PROVISION OF STORE ROOM IN SAGAR PRAHARI BAL (SPB), PROVISION OF LAND DEVELOPMENT AROUND HRDF AND IAAMS SITE TO PREVENT WATER LOGGING AND PROVISION OF GALVALUME SHEET PARKING SHED FOR FOUR WHEELERS NEAR ADMIN BUILDING AT DIGLIPUR

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil.

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out in hard/ dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil.

Removing surplus excavated soil material not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose soil.

M&L for plain cement concrete Type B1, 1:2:4 (using 20mm graded granite stone aggregate) as in columns, pillars, piers, posts and struts.

M&L for PCC Type D2, 1:4:8 (using 40mm graded granite stone aggregate) as in foundations, filling and mass concrete.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete.

M&L for rendering 10 mm thickness in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement.

M&L for rendering 15 mm thickness in cement mortar 1:4 on fair faces of brick work or concrete surfaces in two layers (10mm thickness in CM 1:4 and 5 mm thickness in CM 1:4 mixed with water proofing compound), finishing the surface fair and even. Note: WPC shall be measured and paid separately.

Supply only Integral waterproofing compound.

M&L broken stone or boulders hardcore of guage not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rolled/ rammed to a true surface.

M&L 100 mm thickness PCC Type D2, 1:4:8 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. and finishing cement concrete surface even and rough complete all as specified.

M&L 100 mm thick PCC Type B1, 1:2:4 (using 20 mm graded crushed granite stone aggregate) laid in flooring and pavings, etc. and finishing cement concrete surface even and fair (without using extra cement) complete all as specified.

M&L non - skid coloured ceramic tiles 7 to 8 mm thickness (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thickness screed bed in CM 1:6 complete all as specified.

M&L glazed coloured ceramic tiles of size 300x 200x 7 mm thickness in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thickness backing coat in CM 1:4 complete all as specified.

M&L for Reinforced cement concrete Type B1, 1:2:4 (using 20mm graded granite stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete

M&L for Reinforced cement concrete Type B1, 1:2:4 (using 20mm graded granite stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat fair finished surfaces of concrete.

M&L for Reinforced cement concrete Type B1, 1:2:4 (using 20mm graded granite stone aggregate) as in chajjas

M&L for Reinforced cement concrete Type B1, 1:2:4 (using 20mm graded granite stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for high yield strength deformed TMT steel bars 6 mm to 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for high yield strength deformed TMT steel bars 5mm dia and over upto and including 10mm dia cut to length, bent to shape required, as in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium window and ventilator shutters with 4 mm thickness tinted/ frosted glass, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) including mosquito proof wire cloth of stainless 0.36 mm dia and 1.40 mm aperture fixed with aluminium flat and screws complete all as specified

S&F aluminium Deco grill DG 202 pattern with aperture of size 60x45 mm securing with suitable aluminium channel to frame complete all as specified and directed. Make: Jindal or equivalent section from Hindalco/ Indalco/ MS Ajit Ind Pvt Ltd

M&L 75 mm thick PCC Type C1, 1:3:6 (using 20 mm graded crushed granite stone aggregate) laid in plinth protection, laid in panels and finishing cement concrete surface even and smooth without using extra cement including necessary formwork complete all as specified.

M&L for preparing new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete.

S&F mild steel work as in small articles flat iron of required size as in hold fasts, angle cleats, clamps, hooks, straps, pintal hinge and similar small articles conforming to Fe-290 Gde-E-165.

S&F Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 as in columns, truss, purlins etc.

S&F Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality-A.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm long but not exceeding 10 cm long and Diameter of neck in 16 to 20 mm.

M&L preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L for preparing plastered or unplastered new surfaces of walls and applying three coats of white wash complete.

S&F Second class hardwood factory made kiln - seasoned, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and fixed in position complete all as directed.

S&F 35 mm thick second class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats.

M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of 1st quality synthetic enamel paint over a coat of pink primer complete all as directed.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, and fixed.

S&F 200 mm long aluminium anodised, barrel tower bolts of extruded section and fixed.

S&F 150mm long aluminum handles, cast type, anodised.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F mild steel flat iron 40x3 mm as in valley gutter and wind tie and similar work including securing bolts and necessary drilling work conforming to Fe-290 Gde E-165

Rough excavation of any depth and getting out in any type of soil (soft/ loose or hard/ dense soil) complete all as directed.

Removing excavated soil material to a distance exceeding 500 mtr but not exceeding 1000 mtr and depositing where directed at a level not exceeding 1.50 mtr above the starting point complete all as specified and directed.

Spreading and levelling in layers not exceeding 25 cm thick, well ramming including watering as required.

M&L for Forming Contraction (Dummy) joints 40mm deep x 10mm wide, filled with sealing compound Grade 'A'

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A'

M&L for PCC Type B2, 1:2:4 (using 40mm graded granite stone aggregate) as in foundations, filling and mass concrete.

Supply, fix, test and commissioning solar LED street light fitting (dusk to dawn) with autonomy backup system work for 2 or 3 nights in cloudy weather conditions of 45 Watt solar street light with complete system of panel, LED light, panel frame, bracket, powerful lithium ferro phosphate battery which is integrated with LED driver and LED module as street light source with 5 mtr octagonal pole as per IS including suitable size battery all as specified and directed. Make: Crompton cat No. CSOPSIN5P-45-CDL or equivalent make in Greaves / Philips. Note: Excavation and PCC work shall be measured and paid separately.

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 mtr and making good surface

M&L for PCC Type C1, 1:3:6 (using 20mm graded granite stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Supply, lay and testing XLPE insulated, cores laid up, PVC innersheated, armoured with glavanised wire, heavy duty LT UG electric cable with solid aluminium conductor, 1100 Volts grade, extruded PVC Type ST2 sheathed, conforming to IS: 7098 (Part I) 1988 of cross- sectional area 10 sqmm 2 core .

M & L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including PVC casing and caping with all fittings such as internal bend, end caps etc fixed on the surface of wall, ceiling, roof, steel structure etc. by means of suitable fixing accessories, with GI pressed steel / PVC box suitable for modular switches sunken boxes (with earth dolly) covered with logic modular PVC sheet cover for fixing of switches, sockets etc including PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- NOTE: - Switch and socket to be measured and paid for separately. (a) One light point controlled by one 6 Amps one way switch.

S&F modular switch 6 Amp, flush type, one way, single pole, 1 module complete. Make: Legrand / Philips / Crabtree

S&F ceiling rose, surface bakelite, 65x50 mm, flush type, two to three terminals.

S&F 20 Watts surface and wall mounted 4 feet LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver including connecting up with twin core twisted flexible copper conductor cable with suitable size and length complete all as specified and as directed. Make: Havells cat No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent make in Crompton / Philips

S&F sheet metal enclosure DB SPN 4 way for provision of MCBs of different capacities SP 240 volts with suitable busbar, double door type with IP-44 protection glass complete.

S&F MCB SPN 6-32 Amps, 240 V, 10kA rupturing capacity.

S&F MCB SP 6-32 Amps, 240 V, 10kA rupturing capacity.

A N KUMAR