AMCH/ PICU-40 Setting up of Pediatric Intensive Care Unit (PICU)/ Beds in Assam Medical College and Hospital, Dibrugarh. (Construction of Civil Works, MGPS Works and Electrical Works

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from

natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural

sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and

cantilevers Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement : 4 coarse sand)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement prime

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm

over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Applying Priming Coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete: 100x58x1.90mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete: 300x16mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 100X58X1.90 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Anodized (AC 15 ) aluminium tubular handle bar

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 40 mm dia nominal bore

50 mm dia nominal bore

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

Group B

Group C

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

Group B

Group C

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

15/16 amp switch

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

2 X 16 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way double door

8 way double door

12 way double door

16 way double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Triple pole and neutral

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 Amp, 30KA, FPMCCB

200 Amp, 36KA, FPMCCB

250 Amp, 50KA, FPMCCB

400 Amp, 50KA, FPMCCB

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Supplying including fitting and fixing bus bar chamber ( HPL/ GECO / or equivalent make) with 4 strips bus bar of length 350/450/600/900 mm made of aluminium alloy or wrought aluminium suitable for 100 amp capacity complete with all accessories including connection etc. as required complete

Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C&S, Havells, Indo Asian, HPL, GECO make) 200A

Erection of angle iron/ channel iron cross arm on wood/ RCC/ PCC/ steel tubular/ rail pole etc. as required.

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Erection of all aluminium conductor of 7/1.96 mm to 7/3.10 mm diameter including binding etc. as required.

Supplying fitting and fixing 18 way plastic modular box including cover plate, screw fastener etc. as required complete

Supplying fitting and fixing 12 way plastic modular box including cover plate, screw fastener etc. as required complete

Supplying fitting and fixing 2 way plastic modular box including cover plate, screw fastener etc. as required complete

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Premium model 1400 mm Sweep. (ORIENT PSPO make) /Premium model 1400 mm Sweep SS-390 Deco. Havells make)

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. High Speed 225 mm sweep (ORIENT make), Trans Air 225 mm sweep (Crompton make), Ventil Air DX 250 mm sweep Louver type (Havells make)

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 63A FP 25 KA

Providing and fixing of metalic MCCB Enlosures four pole in wall etc. including drilling holes making connections, etc. as required.

Supplying, erection and commissioning of the following specification as per IS:2713 : 410 SP hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. Pole- 410 SP-60

Supplying and fitting fixing of galvanised channel of 100 mm x 50 mm x 65 x 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying & laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc in hot dip galvenised medium quality 80 mm pipe (cable rate as per RR cable price list and GI pipe rate is as per DSR MP rate) 3½ X 35 sq. mm 1.1 KV grade aluminium conductor armoured UG cable through 50 mm medium quality GI pipe.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV Grade Solid Aluminium conductor up to 10 sq mm balance stranded conductor armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 16.00 Sq. mm.4 Core armoured U.G. cable

25 sqmm 3&1/2 core armoured U.G. cable

35.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

95.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

120.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supplying including installation, testing and commissioning of Air/Water Cooled Diesel Generator set coupled to suitable alternator of 220/415 V, AC, 1/3-Phase 0.8 p.f. mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the Technical Specification.. as per manufacturer. (RANGE FROM 5 KVA TO 625 KV . Kirloskar green/bliss, Leyland, Volvo Penta, Perkinson, Mahindra, Greaves, Escort engine and Kirloskar, Stamford, Leroy somer or equivalent alternator. 200 3 49400x1700x2050 3950 Kg W/C

Supplying, installation testing and commissioning of the following rating copper wound indoor / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure.

200 KVA,50Hz.11/0.433 KV. Oil filled transformer with Off Circuit tap change.

SuppIying incIuding instaiiation of 30 KVA On-Line UPS System (Orion or equivalent maka as approved by the Deptt.) with PWM-IGBT technology360V AC Input (300V – 470V A 3 Ph input- 1 Ph outputWith Isolation Transformer24KW output with 0.8 output PF60 min backup using SMF battery

SuppIying incIuding instaiiation of 60 KVA On-Line UPS System (Orion or equivalent maka as approved by the Deptt.) with PWM-IGBT technology360V AC Input (300V – 470V A 3 Ph input- 1 Ph outputWith Isolation Transformer24KW output with 0.8 output PF60 min backup using SMF battery

Supplying and fixing of 11 KV 400 A Gang operated switch with all accessories complete as required and as directed by the department.

Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

Supplying including installation of 4' dia. C.I. earth pipe complete as required and as directed by the department.

Supplying and erection of CTPT and trivector energy meter including connection as required by the deptt.

Supplying and laying 11 KV AB conductor 3 core 50 sqmm including cable kit etc as required by the deptt.

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical outdoor type double door, floor mounting compartmentalize panel board of size 0.8M X0.9MX 0.40M made of 16 SWG/1.66 mm thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 no legs at the bottom and C.R. sheet roofing on the top. The panel board is to be erected in 1 : 3 : 6 PCC foundation including excavation of trench and brick soling etc. complete neatly Wiring done with provision for one no 400 A 4pole MCCB as incomer and out going as specified and directed by the deptt. confirming to IP 65 protection comprising of the following electrical items: 1. 40mm X 5mm (4X2) strip copper Bus-Bar 0.20M length each 2. Pilot lamp (R Y B) - 3 nos.

(Incoming & Outgoing Switch Gear of reqd. rating will be measured and paid separately) Supplying and erection of wall mounting type panel board including provision foe 200A MCCB incoming and outgoing , required busbar with connections as required complete

Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as approved by the Deptt.) and as directed by the department.

1 Ton Capacity Voltas make

1.5 Ton Capacity Voltas make

2 Ton Capacity Voltas make (Approved rate of the C.E.PWD Bldg, Assam)

Supplying fitting and fixing LED street light light 45W Bajaj make road way liighting luminaries in existing pole ( Approved rate of C.E. PWD(Bldg), Assam) Supplying fitting and fixing LED tube light of 4 ft long 20W HPL make model Neptune plus directlyon wall or ceiling after removing the existing tubefitting as directed by the deptt.

(Accepted rate of the S.E.PWD GEC Guwahati)

Supplying installation and commissioning of Teller com care wireless Nurse Calling System inclung all accessories as reqiured by the deptt.

Supplying installation testing and commisssioning of GST200N-1 Fire Alarm control Panel, 30 zones, LCD display, intelligent Addressable fire alarm system with smoke detector, mannual call point, heat detector, hooter etc as required complete and as directed by the deptt.

Supplying installation testing and commisssioning of CCTV system 4 TB Surveillance Internal Hard Drive HDD-3.5 inch SSATA 6Gb/s 64 MB Cache for DVR NVR Security Camera system with all accessories as required and as directed by the deptt.

Supplying fitting and fixing of EPABX System 8 port analog Euroset 2005 non CLI phone with caller ID system 50 pair MDF box with original Krone Module fitted in wall mounted cabinet box etc as required complete and as directed by the deptt.

Supplying fitting and fixing of time switch and making necessary connection as required.

Supplying installation testing and commissioning of 400V, AVR of input 340-480V and output 415 V with bypass switch as directed and specified by the department. Andrew Yule or equivalent make as approved by the Deptt.

Providing and fixing of Carbon-di-oxide type fire extingushers consisting of welded M.S. cylindrical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamelled paint and fixed to wall with brackets complete withinternal discahrge. Capacity 4.5 Kg

Cost of load security. Meter security etc to be paid to APDCL

MEDICAL OXYGEN (O2) SYSTEM- Supply, Installation, Testing & Commissioning of Oxygen manifold extendable type complete with middle frame with chain for individual cylinder (bulk cylinder D type) along with non-return valves for every cylinder and high pressure annealed copper tail pipes with 1 end having brass adapter and the other end suitable for manifold non return valves and manifold will have 10 brass non return valves for individual oxygen cylinder, middle frame with circumferential M.S. Flat duty powder coated all as specified and as directed. Conforming to 3 digit CE Mark with ISO 9001-2015 certified organization. 2+2

Supply, Installation, Testing & Commissioning of Fully Automatic Digital Gas Control Panel for O2 Features: i) The control panel cover is made using high quality M.S. Duly powder coated. ii) The supply of Gas does not depend on electricity. iii) Display is provided with built-in led to indicate high, normal and low line pressure. iv) Panel cover is fitted with lock to prevent unauthorized access, and can be swing open for maintenance. v) It includes pressure gauge (63mm) that indicated the gas pressure of each header and pipe line distribution pressure. vi) Capable to supply a distribution flow rate in excess of 2500LPM. vii) Manufactured by CE certified/ IS0 9001-2015Organization. vii) Easy usage and maintenance.

Supply, Installation, Testing & Commissioning of Terminal Units (Oxygen Gas Outlets) with probes/ Adaptors as per CE certified/ ISO certified Organization.

Supply, Installation, Testing & Commissioning of Oxygen Flow meter, made with chrome plated brass body. Graduated flow tube and cover made of polycarbonate unbreakable. Adjustable flow by needle valve knob with micrometrical regulation. Humidifier bottle is made of unbreakable polycarbonate material and is autoclavable.

O2 Ventilator Probe

MEDICAL AIR SYSTEM (DUPLEX)

Supply, Installation Testing & Commissioning of INGERSOLL RANDI ANESTIWATA MOTHERSON/FS CURTIS CE marked oil free high pressure Air Compressor machine, 3 Face, Duplex, Durable cast-iron with two intermediate duty applications. With Dual 7.5 HP Motor Supply. Installation Testing & Commissioning of 500 Ltr Air Receiver Tank with safety valve.

Supply, Installation, Testing & Commissioning of Air drye.

Supply, Installation, Testing & Commissioning of Bacterial filterAssy.

Supply, Installation Testing & Commissioning of pressure reducing system with two nos pressure regulator.

MEDICAL VACUUM SYSTEM

Supply, Installation, Testing & Commissioning of INGERSOLL RANDI ANESTIWATA MOTHERSON CE marked vacuum Pump with accessories, base mounting Capacity: 7.5 HP Duplex 7.5 HP each Double Stage Vacuum pump including necessary Vacuum Accessories Like Silencer, Receiver Tank (1000 Ltr) &Vacuum Bacteria Filter. Supply, Installation, Testing & Commissioning of Terminal Units (Gas Outlets) for Vacuum with probes/ Adaptors as per CE certified/ ISO certified Organization.

Supply, Installation, Testing & Commissioning of Ward Vacuum Unit with Regulator alongwith vacuum gauge, collection jar of 600ml capacity reusable plastic collection bottle with overflow safety tap wall mounted type with bracket complete all as specified and as directed.

Copper Pipes Solid drawn seamless, de-oxidized, non arsenical, half-hard, tempered and de-greased copper pipe conforming to latest BS EN 13348 :2001 and manufactured as per BS: 2871, 1971 Part I Table X (or as per EN1057). All copper pipes will be de-greased & delivered capped at both ends The pipes will be accompanied with manufacturers LLOYD test certificate i) 12mm OD x 0.7mm Thick

ii) 15mm OD x 0.9mm Thick

iii) 22mm OD x 0.9mm Thick

iv)28mm OD x 0.9mm Thick

iv)42mm OD x 1.2mm Thick

Supply, Installation, Testing & Commissioning of Zonal Valve Box, are fully designed to suit multiple operational and requirement and ensure considering space for mounting. The configurations are Valve Boxes are described.:- i) 3 Gas Services- O2, Vacuum, Air

Supply, Installation, Testing & Commissioning of Area Line Pressure Alarm with displays for various faults indications and capable of monitoring maximum 5 medical gas service by means of pressure switches etc with audible warning with automatic reedit when the gas service returns to normal as per standard specifications all as specified and as directed for the following Area Line Pressure Alarm:- ii) 3 Gas Line Pressure Alarm

Supply, Installation, Testing & Commissioning of Isolation Valves with brass body with nickel plate valves operating handle suitable for 15mm OD copper pipe to 76 mm OD copper pipes with brass adapter as per standard specifications all as specified and as directed for the following Isolation Valves: 15mm OD

Sri Bhaben Bora