SPECIAL REPAIRS TO BUILDING NO P 355 UNDER GE CME KHADKI

Amount

Taking down chowkat or frame with shutters (without taking off shutters from the frames) area exc 1.50 sqm but n exc 4.0 Sqm each all as specified and as directed.

Taking down Chowkat or frame with shutters without taking off shutters from the frame area n. exc. 1.50 Sqm all as specified and as directed.

Dismantling of single layer Mangalore Pattern roof tiles laid dry all as specified and directed

All as per item No 3 above but bedded in lime or cement mortar all as specified and directed.

Dismantling of battens for tiles, shingles of any size including tilting fillets spacing exc 15 cm all as specified and directed.

Dismantling of timber in scantling 40 sqcm and over in section in any position all as specified and directed.

S&F Framed work such as roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing(beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W(Gde E-250) Quality A all as specified and directed.,

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates Fe-410-W(Gde E-250) Quality A all as specified and directed.

S&F 8 mm thick MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 (gde E-250 Quality B ) all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred, put to gether with glue pinned at joints supplied and fixed all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel and iron work of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

M&L for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. all as specified and directed.

M&L for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters all as specified and directed.

Taking down shutters only of any size exc 1.00 Sqm but not exceeding 2.00 Sqm each all as specified and directed.

S&F 30mm thick flush shutter, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match all as specified and directed.

S&F 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) all as specified and directed.

S&F mild steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded all as specified and directed.

M&L for preparing of surfaces of steel and iron work and treating small articles with tar or col tar or black paint such as stop, covers, gully grating, hold fasts, end of posts area exc 0.1 Sqm each all as specified and directed.

M&L PCC type B1 (1:2:4) (using 20mm graded crushed stone aggregate) as in copings, bed plates, fixing of hold fasts and other similar works and the like including weathering, slightly rounded or chamfered angles and throating as directed includig use and waste of necessary form work all as specified and directed.

M&L for Preparing New Wood and Wood Based Surfaces of any description, over 100mm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Coat of Pink Primer all as specified and directed.

S&F PVC Solid Door Frame of Size 50X47mm made out of 5.0mm Plain Colour PVC Sheet Reinforced with Mild Steel Square Tube as per Manufacture’s Instructions all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face all specified and directed.

Dismantling Wrought Iron or Mild Steel Work, viz. Mild Steel Flat Iron, Mild Steel Bars, Bends, Straps and Similar Work including Mild Steel Bolts, Nuts, etc., fixing to RCC Fencing Posts, Struts, etc. complete all as specified and as directed.

S&F framed work such as grills or grating etc with ends of bars shouldered as framed guard bars conforming to Fe-290 Gde E- 165 all as specified and directed.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodised all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section all as specified and directed.

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Staples all as specified and directed.

S&F in repairs 150mm dia double legged door stopper of aluminium alloy with rubber all as specified and directed.

S&F powder coated Aluminium sliding windows three track with two glass shutters using 4 mm thick glass tinted Modi guard and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, Aluminium cleat, PVC track, bearing, handle lock rubber beading all as specified and directed. Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

S&F Powder coated aluminium ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including pin headed glass necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) all as specified and directed.

M&L for 20 mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and as directed..

Rounding to edges of stone slabs, such as in steps and other similar situation all as specified and directed.

M&L 15mm thick cement plastering on block/stone masonry surfaces in CM 1:4, finishing surfaces even and smooth without using extra cement all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets) all as specified and directed.

M&L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28mm x 0.7mm main tee of size 24mm x38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes, etc. all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of GI Grid work : Armstrong/Swastik/Techno Grid and Make E board Gypsum or equivalent approved .

S&F in repairs 18/19 mm thick Veneered decorateive plywood, grade 1 (with BWR resin) with decorate face veneers on both faces; fixed with screws to timber frame work including dismantling of existing wooden boarding all as specified and directed. Make : Duro/National

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or aboved ground level) all as specified and directed.

M&L 25 mm thick PCC type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in sub base all as specified and as directed.

M&L screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles in store and rubbish of the premises outside of MD land all as specified and directed.

M&L Coloured Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

M&L Non - skid Coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

M&L for Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

M& L rendering 10mm thick in cement mortar 1:4 as in backing coat all as specified and directed

M&L glazed ceramic coloured tiles in verticle surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed,

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection all as specified and directed.

Raking out joints /pointing to random rubble or polygonal rubble uncoursed or brought upto courses built in cement mortar all as specified and directed.

M&L raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM 1:4 including necessary scaffolding upto all floor all as specified and directed.

S&F in repairs 15mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F in repairs 20mm dia steel water tubing medium grade galvanized iron with and including all fittings such as bend, tees, union, etc. and fixed complete to walls and ceilings or laid in floors including taking down existing U/s pipe all as specified and directed.

Cutting chase, pining in and making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps, cills, sunshades, shelves,lintels,etc and cutting chasesfor concealed water tubing and making good, cutting n.exc. 10cm girth in brick walls all as specified and directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses all as specified and directed.

S&F in repairs 110mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old pipe all as specified and directed.

S&F in repairs 75mm dia PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old pipe all as specified and directed.

S&F in repairs 110 mm dia PVC (SWR) bends any radius, provided with access door as specified and directed.

S&F in repairs PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 110 mm bore provided with access door all as specified and directed.

S&F in repairs PVC (SWR) junction single (single T) equal or unequal 110mm bore, provided with access door all as specified and directed.

S&F in reparis 75 mm dia PVC (SWR) bends any radius provided with access door all as specified and directed.

S&F in repairs PVC (SWR) branch pieces, single (single Y) equal or unequal, 75 mm bore, provided with access door as specified and directed.

S&F in repairs PVC (SWR) junction single (single T) equal or unequal 75mm bore, provided with access door all as specified and directed.

S&F in repairs 75mm PVC(SWR) vent cowl all as specified and directed.

All as per item No 64 above but 110mm all as specified and directed.

Demolition of brick or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and directed.

M&L precast solid block masonry in PCC 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 all as specified and directed.

M&L 15mm thick cement plastering on brick/block masonry surfaces in CM (1:4), finishing surfaces even and fair without using extra cement all as specified and directed.

M&L for one coat of synthetic enamel paint over wooden surfaces including preparation of old surfaces over 10cm width or girth all as specified and directed

M&L for painting one coat of synthetic enamel paint on steel surfaces including preparation of old surfaces of any description, over 10 cm width or girth not otherwise described all as specified and directed

M&L for complete scraping down of old decorative surface of walls with steel wire brushes of smoke spots, moulds, moss efflorecent salts and applying complete wall with 3mm thick POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying a coat of POP/Birla wall putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

S&F in repairs table top wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet, outlet connections complete all as specified and directed. Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE.

S&F in repairs viterous china wash down water closet pan (pedestal pattern) white (including fixing bolts, flushing cistern and flush pipe) including provision of flush pipe, plastic seat cover for pedestal pan and CP health faucet including two way angle cock complete all as specified and directed. Make : cera

S&F in repairs brass chromimum plated two way bib cock, fancy type, 15mm bore ( min Wt. 550 grams) of approved make all as specifed and as directed.

S&F in repairs for brass chromium plated, 15 mm bore health foucet, ( flexy type) 1.00 mtr. Long of approved make all as specified and as directed.

S&F in repairs 15mm bore fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed

S&F in repairs decorative cabinet looking mirror with necessary fixing arrangement all as specified and directed.

S&F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stainless steel bracket, guard and railing 60 cm long all as specified and as directed.

S&F in repairs 15mm dia concealed stop valve chromium plated fancy type , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union all as specified and directed.

S&F in repairs Soap dish holder all as specified and directed.

S&F in repairs toilet paper holder all as specified and directed.

S& F in repairs Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe all as specified and directed.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed.

S&F in repairs stainless steel overhead shower rose 200 mm dia with swivel joint and shower arm 20cm all as specified and directed.

M&L 40mm thick PCC type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in sunkun floor all as specified and directed.

M&L 15mm thick plastering in CM 1:3 along the wall and floor of toilet and bath mixed with 3 % WPC and finished surfaces even and smooth without using extra cement all as specified and directed.

Supply only WPC powder all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying complete ceiling with 3mm POP/Birla putty and making smooth surface and applying three coats of white wash over a coat of POP/Birla wall care putty all as specified and directed.

Dismantling of water tanks and removing to store capacity exc 250 & n.exc 500 ltrs all as specified and directed.

S&F 500 ltr. Capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position with ball valve all as specified in SSR Part I

M&L Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish all as specified and directed.

M&L machine cut kota stone slab as in flooring 20-25 mm thick laid over and including 20mm thick (avg thickness) cement screed in CM 1:6 base, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting , waste, rubbing and mirror polishing (granite finish) all as specified and directed.

M&L machine cut kota stone slab as in skirting 20-25mm thick in riser of steps, skirting, dado and pillar including 15mm thick (avg thickness) rendering in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, waste, rubbing and polishing (granite finish) all as specified and directed.

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decoirative type curtain rods including brackets for fixing curtain rod all as specified and directed.

M&L in repairs Roof Treatment on existing Concrete Surfaces with the following Specifications:– (a) Rendering 10mm thick in Cement Mortar 1:4 including mixing of Water Proofing Compound (WPC) as per Manufacturer’s Instructions on Cleaned Concrete Surfaces of Roof after applying a Neat Cement Slurry @ 3.0 Kg per Sqm, Plastered Surfaces Fair finished including Curing of Plastered Surfaces for 7 DAY by pounding of Water over the Roof. (b) Applying evenly one Coat of Cold Bituminous Primer conforming to IS-3384-1986 @ 0.30 Litre per Sqm on the Cleaned Plastered Surfaces. (d) Applying a layer of APP based Polymeric Membrane, 3.00mm thick (minimum) Weighing 3.0 Kg per Sqm (reinforced) with Polyester Non Woven Fabric weighing not less than 160 Gram per Sqm by Torch application. The Overlap shall be minimum 100mm on Traverse direction and 75mm on Longitudinal direction and Sealing Overlap. (e) Applying evenly one Coat of Aluminium Paint @ 0.10 LITRE PER SQUARE METRE over the APP Based Polymeric Membrane. (f) PCC 1:2:4 type BO using 12.5mm graded stone aggregate for filleting and benching slightly rounded or chamfered on edges.

M&L for complete removal of existing treatment from walls, filling the holes/cavities and platering the surface required, cleaning and preparation of the surfaces and applying 3mm thick POP/Birla wall care putty and making smooth surfaces and applying two coats of exterior emulsion paint 100% acrylic (Apex) over a coat of primers as per manufactured instruction all specified and directed. Note : The rate shall be quotted by the contractor including scafolding to carry out the work for height more than 10.00 mtrs.

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat all as specified and directed.

M&L Polythene film black 50 micron laid in floor all as specified and directed.

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut, exc 10cm and n exc 15cm long and 10 to 15mm in dia all as specified and directed

S& F in repairs Wash hand basin mixer complete as specified and directed by Engr-in-Charge. (Jaquar

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings, etc. and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc to match with the existing surfaces all as specified and directed.

Taking down ceiling fan/exhaust fan any size or any type and deposited to AGE E/M store for repair / painting all as specified and directed.

Taking down old and unsrevicable main incoming MCB DB TPN/SPN, main switch including MCCBs/MCBs and making good the disturbed surface all as directed specified and directed.

Taking down carefully unserviceable Sub main wiring of any size and type, removing material from for taking credit and making good the disturbed surfaces of walls, ceilings etc to match with the existing surfaces

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and including not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly including PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators One light point controlled by one one way switch all as specified and directed.

All as per item No. 108 above but One fan point controlled by one way switch and one regulator.

All as per item No. 108 above but One Exhaust fan point controlled by one way switch.

All as per item No. 108 above but One 3 pin switch socket outlet 6A on independent board.

All as per item No. 108 above but One 3 pin socket outlet 6A on same board with other switches

All as per item No. 108 above but one light point controlled by two 2-way switches

All as per item No. 108 above but One bell / buzzer point controlled by one push button.

All as per item No. 108 above but with cable size 2.5 sqmm for switch socket outlet point 16 A on independent board including 2.5 FRLHS cable sqmm PVC insulated unsheathed copper earth continuity conductor as earth wire and connected to earth dolly all as specified and directed.

M&L sub main wiring with Four single core PVC insulated unsheathed stranded copper conductor cable of size 6 sq mm drawn through and including heavy duty PVC conduit 20 mm or higher dia as required at site, totally concealed in walls /floors/ceiling etc including all conduit accessories /fitting/junction box/inspection covers etc of heavy grade, ISI marked with 6 Sqmm PVC insulated unsheathed stranded copper conductor as a continuous earth wire connected to earth dolly all as specified and directed. Note : (i) Four single core cable and one run of earth copper conductor and heavy duty PVC conduit will be measured and paid as one unit length.

M&L sub main wiring with Four single core PVC insulated unsheathed stranded copper conductor cable of size 16 sq mm drawn through and including heavy duty PVC conduit 25 mm or higher dia as required at site, totally concealed in walls /floors/ceiling etc including all conduit accessories /fitting/junction box/inspection covers etc of heavy grade, ISI marked with 6 Sqmm PVC insulated unsheathed stranded copper conductor as a continuous earth wire connected to earth dolly all as specified and directed. Note : (i) Four single core cable and one run of earth copper conductor and heavy duty PVC conduit will be measured and paid as one unit length.

S&F switch Modular, one way, 6 amps, 1 module all as specified and directed.

S&F switch Modular, two way, 6 amps,1 module all as specified and directed.

S&F Modular Bell push, 6A ,1 module all as specified and directed.

S&F switch Modular, one way, 16 amps, 1 module all as specified and directed.

S&F socket modular 6A, 2/3 pin combined 2 module all as specified and directed.

S&F socket modular 6A/16A, 2/3 pin combined 2 module all as specified and directed.

S&F modular fan regulator step type 120W, 2 module all as specified and directed.

S&F Sheet metal enclosures 230v, single pole and nutral enclosure with a two pin and earth plug with socket with one single pole MCB 20 Amp all as specified and directed.

S&F Bell, AC 230 V, single pole all as specified and directed.

S&F ceiling rose, 3 phase PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal including PVC square block all as specified and directed.

Painting of ceiling fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust all as specified and directed.

Re-Fixing of ceiling fan any size and any type, after cleaning and connecting up including provision of cable 1.5 sqmm three core from ceiling rose or connector to fan all as specified and directed.

Re-Fixing Exhaust fan any size and any type after cleaning and connecting up including provision of cable 1.5 sqmm three core from ceiling rose / connector to fan all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose coall as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 1 feet, 5 watt 220 V, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

M& Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as specified and directed.

S&F LED inverter Bulb 9 watt With inbuilt battery back up of upto 4 hours cat part no - SZBLB22009-iBB Make- Shakti, Havells, Bajaj

S&F sheet metal enclosures VTPN as MCCB incomer and MCB SP out going 4 way 415 V, AC dubble door surface/ flush mounting made with CRCA sheet steel, powder coated Cat No 811888 IP 43 protection isolated neutral bar insulated bus bar assembly make INDOASIAN or equivalent all as specified and directed.

S&F MCCB 4 Pole, 415 Volts 50 HZ, of capacity 125 Amp, 16 KA. Suitable for VTPN DB as incomer with spreader terminal Cat No 830273 Make INDO ASIAN, Ics= 100% of Icu or equivalent all as specified and directed.

S&F 415V, 10KA 'C' curve miniature circuit breaker (MCB) of TPN 40 to 100 AMP current carrying capacity in the DB complete with connection testing and commissioning all as specified and directed.

S&F sheet metal enclosures MCB TPN- DB-04 way 415 V as MCB TPN incomer and MCB SPN out going 4 way 415 V, AC dubble door surface/ flush mounting with 200A rated bus bar all as specified and directed.

S&F sheet metal enclosures MCB SPN- DB-08 way, 230 V, double door flush type with 200A rated bus bar all as specified and directed.

S&F 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and neutral (SPN) with current carrying capacity of 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and directed.

S&F 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole (SP) and current carrying capacity 40 Amp in the MCB DB complete with connection testing and commissioning all as specified and directed.

S&F 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole (SP) and current carrying capacity 6 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and directed.

S&F LED fitting for Bldg security, 35 Watt, 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete including conncting with 1.5 sq mm copper condector 3 core flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr lenth with necessary bending all as specified and directed

M&L for earthing complete with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including G.I. wire of size 4 mm dia by means of bolts, nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. including charcoal dust and common salt, packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 & RCC Chamer cover of size 540x540x100 mm made with 1:2:4 type B1, using 8 mm MS bar for reinforcement and handle , 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement including excavation and earth work in any type of strata and testing on completion all as specified and directed.

Taking down electric water heater (geyser) of 25/50 ltr capacity and refixing the same after repair alongwith connected accessories such as PVC connection pipe, fastner etc complete all as specified and directed. Note : cost for spare parts required for repair of geyser is deemed to be inclusive in the unit rate of this item.

Taking down old single phase electric meter and refixing the same alongwith proper connection complete all as specified and directed. Note : Quarter wise last meter reading shall be noted by the contractor and submitted AGE E/M office before taking down metre.

S&F on wall / Roof/surface PVC wiring duct G1 of size 40 mm width and 60 mm height Cat part no -TBWDN40X60LG1 suitable for Sub main wiring all as specified and directed.

S&F Anti Suicide Fan rod including drilling, cutting, threading for ceiling fan 1200/1400mm sweep of length 18" all as specified and directed.

Mukund Engineers and Contractors (BID ID -3451867)

H S TAKHI (BID ID -3452881)

ShreHari Civil Enginneering and Contractors (BID ID -3453537)

vishalconstruction (BID ID -3453151)

MANIYA CONSTRUCTION CO (BID ID -3453515)

UNIQUE ENGINEERS (BID ID -3452894)

MAHESH DADAJI BACHHAV (BID ID -3449625)

Bidder Name

H S TAKHI

BSK Construction

UNIQUE ENGINEERS

vishalconstruction

MAHESH DADAJI BACHHAV

Mukund Engineers and Contractors

ShreHari Civil Enginneering and Contractors

MANIYA CONSTRUCTION CO