PROVN OF INSTRUMENT AND ELECTRO MEDICAL EQPT SHOPS AND SMALL ARMS AND SPL REPAIR TO FLOOR OF TYPE SHED SW, STORE SEC NO P-130 AND P-133, REPAIR/REPLACEMENT OF 13 X WOODEN WINDOW AND PROVN OF PVC CLOSED DRAINAGE PIPE UNDER AGE B/R-I AT GE JHANSI

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, etc or for the shafts, well, cesspits, manholes, pier holes, etc n exc 10 Sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point soft soil complete all as specified and directed.

M&L Cement concrete in foundations, filling and mass-concrete type D2 1:4:8 (40 mm graded aggregate) complete all as specified and directed.

M&L Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface are complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L Brickwork with subclass*'B’ bricks, straight or curved on plan to any radius in half brick thick walis built in CM 1:4 all as specified and directed.

M&L for pre-cast cement concrete block masonary with solid type B-1 1:2:4 (using 20mm graded stone agg) exc 10cm in width and setting in mortar 1:4 complete all as specified and directed.

M&L cement concrete 75 mm thk, type D2 1:4 :8 (40 mm graded stone aggregale) in sub base of flooring complete all as specified and directed.

M&L 40 mm thick plain cement concrete as in flooring type B1, 1:2:4 (20mm graded aggregate) complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type BO (12.50 mm graded Agg) for leveling course complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for Non skid ceramic color tiles of size exc 0.18 sqm not exc 0.38 sqm and 7 to 8 mm thick (square / rectangular) as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) compiete all as specified and direcred.

M&L for ESD flooring mat thiclkness 2mm in rolls of 2.00 mtr X 15 mtr in length, three layered,colour blue,including glue,welding rod,copper strip, contact button and grounding card single side complete all as specified and directed.

M&L Granite (of any type) slab 20mm hick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 20 mm thick screed/ bedding layer in CM (1:6) complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and h laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand ) surface, complete all as specifed and directed. Note The quoted rates are deemed to be inclusive of material agasint form work and joint fillings.

M&L for hardcore of broken stone boulders gauge not exc 63mm deposited, spread and levelled in layers n. exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation etc complete all as specified and directed.

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment etc complete all as specified and directed.

Formwork to edges Rough finished surfaces of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Formwork to edges Rough finished surfaces of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 05 cm but n exc 10cm wide complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

M &L Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Ser item No 27.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde E-250) quality B for roof trusses (framed). trussed, purlins, crane gantnes. rails and fastenings and heavy bracket framing (Beam, tee angle, channel, SHS PIPES or flat sections) including distance pieces, cleats etc, complete all as specified and directed

M&L Reinforced cement concrete (nominal mix) type B0 1:2:4 (12.5 mm garded aggregate) in:- Foundations including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under teamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete (nominal mix) type B0 1:2:4 (12.5 mm garded aggregate) in:Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Rendering 10 mm thick on other than fair faces of brick or concrete surfaces on wall in cement mortar 1:6 mixed with WPC for finished even and smooth without using extra cement complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coat of weather coat paint over a coat of primer complete all as specified and directed.

Preparing newly plastered surfaces of wall and applying two coats of oil bound distember over 1 mm putty and a coat of chalk whitening primer preparating to make the surface to be plain and smooth before primer complete all as specified and directed.

Preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M&L powder coated anodised aluminium door shutters aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber neoprene Packing, handle 2 Nos in each door hinges, anodised aluminium snap bearing screws etc complete all as specified and directed.

S&F 100mm long butt hinges. extruded alluminium alloy with galvanized mild steel hinge pin, anodized and fixed, type B-21 complete all as specified and directed.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 150mm long alluminium handles cast type, anodized and fixed complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue anodised, with hard drawn steel spring 140mm of cover plate length complete all as specified and directed.

S&F Aluminium (Die-cast) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F Mortice lock, vertical type, size 100 m, 4 lever brass complete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S & F 3mm th Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sq.m in each pane complete all as specified and directed.

S & F 5.5mm th Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq.m in each pane complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, handle and steel peg stay complete all as specified and directed. .

M&L for applying two coat of synthetic enamel paint on any surfaces of any description not otherwise described over 10 cm width or girth over red oxide including necessary preparation complete all as specified and directed.

M&L for wrought Second class soft-wood in scantlings complete all as specified and directed

S&F 18mm thick prelaminated MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves/shutter or similar work, complete all as specified and directed

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed.

M&L Aluminium handles 100 mm, cast type, anodised complete all as specified and directed.

Providing and fixing in position, for outer walls 170 mm thick factory made Expanded Polystyrene Core (EPS Core) wall panels consisting of EPS core sandwiched between two Engineered sheets of welded wire fabric mesh duly finished with shortcrete materials on outer faces. The fabric mesh shall be made of 2.5 mm dia G.I. wire mesh with 50 mm pitch in both the directions and on both faces of the wall . The EPS core shall consist of 100 mm thick EPS of density not less than 15 kg/ per cum. Both the outer faces of the panel shall be finished by applying the layer of 35 mm thick cement mortar 1:3 {1 cement: 3 coarse sand (not having more than 40% stone chips of size upto 6 mm)} À with the help of shotcreting/guniting / pressure equipment etc at a pressure not less than 1 bar (100Kn/m2) and both surfaces finished with trowel. Fixing operations of wall panels shall be completed in all respect as per drawings and specifications and under the overall direction of EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design , 3D model design before commencement of work The panel manufacturer should have BMTPC, valid Performance apprasial certificate complete all as specified and directed.

Providing and fixing in position, for inner walls 150 mm thick factory made Expanded Polystyrene Core (EPS Core) wall panels consisting of EPS core sandwiched between two Engineered sheets of welded wire fabric mesh duly finished with shortcrete materials on outer faces. The fabric mesh shall be made of 2.5 mm dia G.I. wire mesh with 50 mm pitch in both the directions and on both faces of the wall . The EPS core shall consist of 80 mm thick EPS of density not less than 15 kg/ per cum. Both the outer faces of the panel shall be finished by applying the layer of 35 mm thick cement mortar 1:3 {1 cement: 3 coarse sand (not having more than 40% stone chips of size upto 6 mm)} À with the help shotcreting/guniting / pressure equipment of shotcreting/guniting equipment etc at a pressure not less than 1 bar (100Kn/m2) and both surfaces finished with trowel. Fixing operations of wall panels shall be completed in all respect as per drawings and specifications and under the overall direction of EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design , 3D model design before commencement of work .The panel manufacturer should have BMTPC, valid Performance apprasial certificate.

Providing and fixing in position for roof 185 mm thick factory made Expanded Polystyrene Core (EPS Core) roof/floor panels made of 2.5 mm dia G.I. wire mesh with 50 mm pitch in both the directions and on both faces of panel,. The EPS core shall consist of 100 mm thick EPS of density not less than 15kg/ per cum. The bottom side of the panel shall be finished by applying a layer of 35 mm thick cement mortar 1: 3 {1 cement: 3 coarse sand (not having more than 40% stone chips of size upto 6 mm)} À with the help shotcreting/guniting / pressure equipment of shotcreting equipment etc at a pressure of not less than 1 bar (100Kn/m2) and surface finished with trowel. The top face of the panel shall be provided and finished by applying 60 mm thick layer of cement concrete 1:1.5: 3 (1 cement :1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). including neassary support for EPS panel /concerete. Fixing operations of roof/floor panels shall be completed in all respect as per drawings and specifications and under the overall direction EPS panel manufactures, the manufactures shall give complete 2D plan design, structural design , 3D model design before commencement of work . The panel manufacturer should have BMTPC, valid Performance apprasial certificate complete all as specified and directed.

S&F steel mesh 50mmx50mmx2.5mm thick fixed with EPS Panels at Corner junctions and other locations as in I mesh, L mesh, C mesh complete all as specified and directed.

Polypropylene construction Fiber complete mixed with concerete @ 1Kg/CUM complete all as specified and directed.

S&F powder coated aluminium sliding window with three track outer frame suitable for sliding aluminium shutters,weight of aluminium section not less than 0.55 kg/RM of three track frame, including necessary joining cleats glazing clips rubber packing shop beading screws with two shutters including 5 mm thick coloured glass and one shutters with stainless steel wire mesh incl necessary locking arrangements,handles and alumunium grill of aperture size 50mm and 4 mm dia, complete all as specified and directed.

M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachmen Fe.290.Gde-E-165 complete all as specified and directed.

S&F 100mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for Brick work old size with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

S&F for mild steel screw bolts (machine made) diameter of neck 16 to 20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exc 10 cm long, complete all as specified.

Demolition of cement concrete(unreinforced) in ground floors and pavings n exc 15 cm thickness(below or above ground level) complete all as specified and directed.

M & L for 100 mm thick PCC 1:4:8 type D2 as in sub base of flooring complete all as specified and directed.

M & L for 50 mm thick PCC 1:2:4 type B-1(20 mm graded aggregate) finished even and smooth using extra cement as in floors complete all as specified and directed.

M & L for 20 mm wearproof topping as specified(incorporating an approved metallic floor hardner ), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) complete all as specified and directed. Note:- (a) Qty of cement and weight of hardener will depend on the propotion recommended by the manufacturer. (b) Metallic hardner shall be measured separately and paid at 'Supplied only' rates

Supply only Metallic floor hardener complete all as specified and directed.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ thickness of concrete slab 100mm complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade A complete all as specified and directed.

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for Finishing surface of concrete roads, pavements, by brooming complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) complete all as specified and as directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame) complete all as specified and as directed.

M &L Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per reopening, all complete as per requirement and direction of Engineer in-charge.

M&L for powder coated aluminum window shutters, side hung type without sash bars, aluminium sections for frame weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber packing, powder coated aluminum snap beading, screws, powder coated aluminum fittings such as peg stays 150mm long (01 No), hinges type B-21 100mm long (02 No), suitable handle (01 No), complete all as specified and directed.

S&F of glass, tinted type, 5.0 mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified and directed.

S&F powder coated anodised aluminium frame for windows and including four track shutter : one gauge and three glazed) sliding type aluminium sections weighting not less than 0.55 kg per mtr including necesarry jointing cleasts, rubber packing anodised aluminium snap gridding, screws, handle of size not less than 100mm, locking arrangement etc complete and 5 mm thick tined glass panles aluminium mosquito proof guage and aluminium guard bar mesh size not less than 75mm x 75mm and making good disturded surface of wall incl PCC,Plaster and OBD/Cement base paint etc complete all as specified and directed.

M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed in floor /trench complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed in floor/trench complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends with access door of any radius complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends with access door of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal.with access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed..

S & F PVC Floor trap of 75 mm outlet with grating including jointing to waste pipe in run lead complete all as specified and directed.

Excavation over areas exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for pipe line or for manholes not exceeding 10 Sqm on plan and not exceeding 1.5m in depth in Soft/loose soil and getting out complete all as specified and directed.

All as per Ser item No 88.00 above but depth exc 1.5m and n.exc 3.00m complete all as specified and directed.

M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Aggregate for loose filling, of gauge 40mm to 80 mm graded as in floor filling complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B0 using 20 mm graded stone aggregate as in sub base etc, complete all as specified and directed.

M&L for glazed ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points:-

One light point controlled by one switch

One Exhaust fan point controlled by one switch.

One ceiling fan controlled by one swith

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Ser item No 94 above but with 2.5 sq mm FRLSH copper wire with 2.5 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

All as per Ser item No 96 above but 2runsX4 Sqmm +1runX4Sqmm complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Notes for item No. 95.00 to 97.00 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.

S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix electronic fan regulator in 5 steps, 240V, 50Hz complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S & F 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix LED batten box type with CRCA sheet steel body pre-wired suitable for and including provision of 1x20Watt (4 feet) retrofit LED tube with PC body and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED batten 9W/10W (2 Feet) complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fix MCB distribution board, TPN, 4 way 415 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 12 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

Supply and fix MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

S& F MCB TPN 63 Amp, 10 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

S& F MCB SPN 40 Amp, 10 KA, 'C' curve, 230 V, 50 Hz complete all as specified and directed.

All as per Ser item No 116.00 above but SP 6 to 32 Amp, 230 V complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 16 sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down existing unserviceable service cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

M&L for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to copper strip 20x3 mm as earthing lead by means of bolts, nuts, check nuts and washers of copper and earth wire protected by 50mm dia GI pipe medium grade and connected to pole structure/ panel board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20x3 mm copper strip all as specified and directed.

Supply and fix in replacement of ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

S&F cooling and heating type split air conditioners , electric driven, single phase of capacity of 1.5 TR BEE 5 star rated completed all as specified and directed.

Supply and fix Voltage steblizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and capacity of 4.0 KVA completed all as specified and directed.

Supply and fix air curtain 4 ft completed all as specified and directed.

NIHAL ENTERPRISES

SHIV SHANKAR MISHRA