CERTAIN B R AND E M REPAIR OF OTM ACCN MH UNDER AGE B R I AT AMRITSAR CANTT

Demolition of cement concrete (unreinforced) of any description or in any position not otherwise specifically provided for, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete in proportion 1:2:4 type B-0 (using 12.5 millimeter graded stone aggregates) as in padding concrete fair finish, roof kerbs or mud stops, rounded or chamfered on edges and similar work, including slight rounded weathering and throating; Complete all as specified and as directed.

For one three pin socket outlet 5 Amps independent board complete.

Supplying and Fixing in replacement, Sub main wiring with two single pole 6 Square Millimeter (nominal area) stranded copper conductor Flame Retardant Low Smoke Polyvinyl Chloride insulated and unsheathed cable drawn in existing non-metallic Polyvinyl Chloride rigid conduit, medium grade, of suitable size, with all standard fittings, including one run of continuous 6 Square Millimeter (nominal area) Flame Retardant Low Smoke Polyvinyl Chloride insulated stranded copper conductor cable for earth continuity. This includes taking out and removal of old sub main wiring, complete as specified and as directed. (Note 1: Two runs of 6 Square Millimeter main cable and one run of 6 Square Millimeter earth cable shall be measured as one unit/one Running Meter.)

Supplying and Fixing powder coated anodised aluminium frame for doors, windows, and ventilators with one or more rebates, including joining cleat for fixing and all necessary items (minimum thickness of powder coating 50 micrometer).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing rubbish off the premises.

Material and Labour for Vitrified Ceramic tiles 10 millimeter thick, light shade (square or rectangular), polished, area of each tile exceeding 0.42 Square Meter but not exceeding 1.00 Square Meter, in floors and similar locations, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15 millimeter thick screed bed of cement mortar 1:6, complete all as specified and as directed.

Supplying and Fixing glazed ceramic coloured tiles 450 millimeter by 300 millimeter by 6 millimeter thick, and similar items on vertical surfaces such as skirting, dados, and risers to steps and similar locations, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10 millimeter thick rendering plaster in Cement Mortar 1:4 on brick surface, complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving not exceeding 15 centimeter thickness (below or above ground level) and disposing the rubbish to a distance exceeding 50 Meter but not exceeding 100 Meter away to low lying areas, complete all as specified and as directed.

Material and Labour for 75 millimeter thick Cement Concrete type D-2 in proportion 1:4:8 (using 40 millimeter graded aggregate) as in sub base of floor, complete all as specified and as directed.

Material and Labour for Providing and laying 60 millimeter thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design and pattern as in footpath, parks, lawns, driveways or light traffic parking and similar areas, of required strength, thickness and size or shape, made by table vibratory method using Polyurethane mould, laid in required colour and pattern over and including 50 millimeter thick compacted bed of fine sand. Compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete in proportion 1:2:4 type B-0 using 12.5 millimeter graded stone aggregate in coping, including weathering, slightly rounded or chamfered angle, and throating, as specified and as directed.

Taking down cement plaster of any description on brick walls, and similar surfaces, including raking out joints, hacking for key, scrubbing down with water, and all necessary operations, complete all as specified and as directed.

Material and Labour for Rendering 15 millimeter thick on fair or unfair faces of brick work or concrete surfaces in Cement Mortar 1:6, and finished even and smooth (without using extra lime or cement), complete all as specified and as directed.

Material and Labour for Rendering 15 millimeter thick on fair or unfair faces of brick work or concrete surfaces in Cement Mortar 1:4, and finished even and smooth (without using extra lime or cement), complete all as specified and as directed.

Material and Labour for preparation of newly plastered surface of wall and applying two coats of cement base paint over a coat of primer to match the existing treatment, complete all as specified and as directed.

Material and Labour for preparation of newly plastered or old decorated surface of wall and applying two coats of oil bound distemper with necessary putty filling, complete all as specified.

Material and Labour for Machine cut Kota stone slab flooring 20 to 25 millimeter thick over cement screed base of 20 millimeter thick in Cement Mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing, complete all as specified and as directed.

Material and Labour for rubbing/grinding and polishing of Kota stone/marble tiles/granite (of any type)/cudappah stone flooring, complete all as specified and as directed.

Supplying and Fixing mild steel TMT bars 10 millimeter diameter and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 millimeter diameter or securing with clips, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete in proportion 1:1.5:3 type B0, using 12.5 millimeter graded stone aggregate, for the repair of elements such as Sunshade (Chajja), Fascia, and parapets, including the use of chicken wire mesh, necessary formwork, and scaffolding up to 8 Meters height. The work also includes applying two coats of cement base paint over a coat of primer, applied over cement plaster in proportion 1:4, complete all as specified and as directed.

Material and Labour for Plain Cement Concrete in proportion 1:2:4, type B-0 (using 12.5 millimeter graded stone aggregates) in bed blocks for hold fast and similar works, complete all as specified and as directed.

Material and Labour for two coats of synthetic enamel painting on new wooden surfaces of any description over 10 centimeter in width or girth, not otherwise described, applied over one coat of pink primer, including preparation of previously untreated surfaces, complete all as specified and as directed.

Material and Labour for applying One coat of synthetic enamel paint on steel surfaces of any description over 10 centimeter in width or girth, not otherwise described, including preparation of old surfaces, complete all as specified and as directed.

Material and Labour for applying One c

Supplying and Fixing 300 millimeter long Aluminium alloy, Anodised, sliding door bolt with hasp and staple (bolt type), including fixing clips of sheet, cast or extruded sections, and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, fixed, complete all as specified and as directed.

Supplying and Fixing Aluminium, anodised, barrel tower bolts 150 millimeter of extruded section and fixed, complete all as specified and as directed.

Supplying and Fixing 150 millimeter long Aluminium handles, cast type anodised, complete all as specified and as directed.

Supplying and Fixing, for repair work, 20 millimeter bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and as directed.

Supplying and Fixing Factory made single extruded Wood Polymer Composite solid plain flush door shutter of 30 millimeter size, comprising of virgin polymer of K value 58 to 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 Grams), having minimum density of 650 Kilogram per Cubic Meter and screw withdrawal strength of 1800 Newton (Face) and 900 Newton (Edge), minimum compressive strength 50 Newton per Square Millimeter, modulus of elasticity 850 Newton per Square Millimeter, and resistance to spread of flame of Class A category, with the property of being termite/borer proof, water/moisture proof and fire retardant. Fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk Stainless Steel screws, complete all as specified and as directed.

Dismantling wall and ceiling board (fibre, pulp, insulation, et cetera), or insulation boards/slabs/blankets of any thickness, including cover fillets, complete all as specified and as directed.

Supplying and Fixing 5 millimeter thick hollow Polyvinyl Chloride wall lining consisting of plain colour Polyvinyl Chloride sheet inclusive of solvent cement, Polyvinyl Chloride frame and all necessary items for fixing at site, complete all as specified and as directed.

Supplying and Fixing Galvanized Iron frame work for seamless ceiling, comprising of Galvanized Iron perimeter channel 0.55 millimeter thick with two unequal flanges of 20 millimeter and 30 millimeter and a web of 27 millimeter fixed to the surrounding wall using nylon sleeves and screws at 450 millimeter center-to-center; intermediate channel 0.9 millimeter thick having two equal flanges of 15 millimeter each and a web of 45 millimeter suspended from soffit at approximately 900 millimeter center-to-center with Galvanized Iron cleat and steel expansion fasteners; with and including ceiling section (not exceeding 1.2 Meter length) of 0.55 millimeter thickness having knurled web of 50 millimeter and flange of 26 millimeter each with lips of 10.5 millimeter fixed to the intermediate channel with connecting clips across the intermediate channel at 457 millimeter center-to-center; including Galvanized Iron Hanger 6 millimeter diameter (Up to 1200 millimeter length) adjusting level, fixed to the roof slab by means of ceiling cleats made out of Galvanized Iron flat 40 millimeter by 3 millimeter size, 60 millimeter long and expansion hold fasteners 12.5 millimeter diameter, 40 millimeter long, complete all as specified and as directed.

Material and Labour for Seamless calcium silicate ceiling 12 millimeter thick, made out of 1800 millimeter by 1200 millimeter size board of siliceous and calcareous material reinforced with cellulose fiber, fixed to the ceiling section with 25 millimeter long self drilling and tapping screws having Phillips head with under head cutter at 200 millimeter center-to-center. Including finishing the joint of the face board with specially formulated jointing compound and 48 millimeter wide fiber tape to provide a seamless finish. (Frame work for ceiling shall be measured and paid separately), complete all as specified and as directed.

Material and Labour for preparation of new ceiling surfaces and applying two or more coats of first quality acrylic distemper (ready mixed) of required shade and colour on new work. The distemper shall be of an approved manufacturer, having a Volatile Organic Compound content less than 50 Grams per Liter, complete as per manufacturer's specification and as directed.

Supplying and Fixing 4 millimeter thick Aluminium Composite Panel sheet as in wall cladding, including frame work with all accessories required for fixing. Colour and design of Aluminium Composite Panel sheets as specified and as directed.

Supplying and Fixing, for repair work, vitreous china squatting pan "Orissa" pattern of size 580 millimeter by 440 millimeter with integral foot rest, including water connection to trap and flushing pipe, flushing cistern, and similar items. Including lime concrete in lime mortar 1:3 using broken bricks 40 millimeter graded, and Polyvinyl Chloride (Soil, Waste, and Rainwater) 'P' trap 110 millimeter bore, complete all as specified and as directed.

Supplying and Fixing Polyvinyl Chloride valve less syphonic action type low level flushing cistern of 10 Liters capacity with inlet ball valve, float valve, push button type handle, including 32 millimeter diameter Polyvinyl Chloride (Heavy duty) flush pipe, including brackets and taking down/dismantling old unserviceable cistern, complete all as specified and as directed.

Material and Labour for Box type steel ventilator made of Electric Resistance Welded tube P-section of size 60 millimeter by 25 millimeter outer frame (single rebated), comprising glazed shutter, frame of Electric Resistance Welded tube and Flat Iron 2 millimeter thick welded or screwed to the frame for fixing of sheet glass, including fixtures and fittings such as Stopper, Cleat, Pintle hinges, holdfast, et cetera, all as shown on Drawing Number CEJZ/TD1019/08 sheets 1/3 to 3/3 dated 01 May 2008, complete all as specified and as directed. Note: Sheet glass and painting shall be measured and paid separately.

Disconnecting existing tanks, exceeding 250 Liters and not exceeding 500 Liters capacity. Setting aside (or lowering if required) for repairs, cleaning, and similar operations, and hoisting if required. Reconnecting and re-fixing in position, including cleaning, repairing, and all necessary operations, complete all as specified and as directed.

Disconnecting existing tanks, exceeding 500 Liters and not exceeding 1000 Liters capacity. Setting aside (or lowering if required) for repairs, cleaning, et cetera, and hoisting if required. Reconnecting and re-fixing in position, including cleaning, repairing, et cetera, complete all as specified and as directed.

Supplying and Fixing, for repair, 25 millimeter diameter stainless steel curtain rods with brackets, stops, rollers, finials, 1 pair of decorative knobs for each curtain rod, and all necessary items, complete all as specified and as directed.

Supplying and Fixing, for repair, 125 millimeter Chromium Plated shower rose fancy type with Chromium Plated arm, complete all as specified and as directed.

Supplying and Fixing, for repair, Chromium Plated brass towel rail of 20 millimeter diameter and 600 millimeter long, complete all as specified and as directed.

per point

Supplying and Fixing of Vitreous china wash down water closet pan (pedestal pattern), white, complete all as specified and as directed. Note: Rate of supply for Flushing cistern and seat cover and similar items have been taken separately.

Supplying and Fixing in replacement Surface Mount Device/PLUTO NEO LED luminaire, 36/40 Watt, 600 x 600 millimeter, 220 Volts Alternating Current LED ceiling light, recessed or surface type, with high efficiency Poly(methyl methacrylate) diffuser, soft glass free light, complete with driver, holders, and LED lamps, suitable for roof/ceiling, including fixing arrangements and connecting with copper wire flexible three core 1.5 Square Millimeter Polyvinyl Chloride insulated 3 core cable from the ceiling rose to the light fitting, complete as specified and as directed.

Supplying and Fixing in replacement decorative Ceiling light, 12 Watt light fitting, Light Emitting Diode type, with accessories, including any type, complete as specified and as directed.

Supplying and Fixing in replacement 1100 volts grade, heavy duty, Polyvinyl Chloride insulated aluminium conductor cable, served with inner sheathing of Polyvinyl Chloride tape and overall Polyvinyl Chloride sheathing, for service connection. This cable is a 2 core, 6 square millimeter, stranded conductor cable, complete as specified and as directed.

For one light/fan/ buzzer point controlled by one 5 Amp switch one way.

Material and Labour for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath, and Water Closets (WCs) and similar areas, as detailed below: (a) Application of two-component acrylic modified cementitious coating on dried surface free from contaminants such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings, and achieve a gripping profile that is clean, dry, and free from laitance and any other form of surface contamination. The installation instructions in manufacturer's literature shall be strictly complied with, including but not limited to the following: (i) Chipping out any visible cracks in a "V-Groove" pattern as applicable (Special attention shall be given to this part). Cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putty/Dr. Fixit 302 SBR latex/perma latex SBR/FOSROC Nitbond SBR latex/Asian paint latex as required. Final cleaning of the surface with a powder grinder, wire brush, hair brush, and vacuum pressure. (b) Dampening all surfaces immediately ahead of application of the acrylic modified cementitious coating (SIKA top seal-107/Brush bond FOSROC/Dr. Fixit/STP/CICO). (c) Whilst the surface is still Saturated Surface Dry (SSD), apply the first coat of acrylic modified cementitious coating (SIKA top seal-107/Brush bond FOSROC/Dr. Fixit/STP). (d) Apply glass fabric sheet (SIKA Fab 1/FOSROC/Dr. Fixit/STP) whilst the first coat is wet. (e) Once touch dry, apply the second coat of acrylic modified cementitious coating (SIKA top seal-107/Brush bond FOSROC/Dr. Fixit/STP/CICO) of viscosity as per manufacturer's instructions on the entire area. (f) The second coat shall be applied after 6 to 8 Hours of application of the previous coat and in a direction at right angles to the previous coat. (g) The waterproofing coating shall be taken to a minimum height of 450 millimeter above the finished floor level on the vertical surface. (h) It is essential to cure the acrylic modified cementitious coating immediately after application (minimum 6 to 8 hours drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking, complete all as specified and as directed.

(j) A protection plaster (12-15mm thick) in cement mortar (1:3) admixed with appropriate integral water proofing compound has to be a applied on the walls. (k) Admixture: Sika plastocrete plus/ FOSROC/ Dr. Fixit/ STP/ CICO confirming to IS 2645. (l) Providing and applying a protection screed 50mm thick in cement mortar (1:4) mixed with SIKA plastocrete over the applied water proofing coating on horizontal surfaces. (m) Admixture: Sika plastocrete plus/ FOSROC/ Dr. Fix

For one three pin socket outlet 5 Amps independent board complete.

For one light point controlled by two way switch.

For one light/fan/buzzer point controlled by one 5 Amp switch one way.

Each Job

it/ STP/ CICO confirming to IS 2645. (n) All the corners and joints should be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansion zone in the centre of make seal tape SIKA/ FOSROC/ Dr. Fixit/ STP. (o) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (p) Water proofing treatment has to be carried out through authorised applicators. (q) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (r) All traps in sunken slabs to be enclosed with PCC (1:1½:3) (min 15cm) alround. (s) The sunken portion shall be filled with PCC (1:5:10) using 40mm graded stone aggregate all as specified. (t) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600mmlong) including cutting hole in existing wall and making good the disturbed surface complete all as specified and directed. (u) Providing 25mm thick cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as sin flooring for laying floor finishes all as specified. Notes :- (i) Item No. (s) and (u) shall be measured and paid seperately. (ii) Plan area (wall to wall/ wall to beam/ beam to beam) shall be measured and paid. No separate measurement for vertical surface shall be accounted and quoted rate shall be deemed to include for the same.

Each job

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, etc., removing materials to store for keeping in safe custody or for taking credit (credit for above items shall be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete as specified and as directed.

Supplying and Fixing Modular switch, flush type, one way, 6 Ampere, 230 volts, complete as specified and as directed.

Supplying and Fixing Modular switch, flush type, two way, 6 Ampere, 230 volts, complete as specified and as directed.

Supplying and Fixing Modular socket, 6 Ampere, 2 or 3 pin combined, 2 module, complete as specified and as directed.

Supplying and Fixing Modular switch, flush type, one way, 16 Ampere, 230 volts, complete as specified and as directed.

Supplying and Fixing Modular socket, 6 or 16 Ampere, 2 or 3 pin combined, 2 module, complete as specified and as directed.

Supplying and Fixing Modular switch, bell push switch, 6 Ampere, 1 module, complete as specified and as directed.

Supplying and Fixing ceiling rose, 65 X 50 millimeter, three terminals, complete as specified and as directed.

Supplying and Fixing Lamp holder, bakelite type, with back plate suitable for batten fitting, complete as specified and as directed.

Material and Labour for point wiring drawn in existing concealed conduit for one light point, fan point, or bell point controlled by one switch (using red, black, and green colour wires as colour coding) complete with 1.5 square millimeter (nominal cross-section area) single core Flame Retardant Low Smoke Polyvinyl Chloride insulated unsheathed and multi-stranded copper conductor cable, 1100 volt (Indian Standards Institution marked), drawn through an existing Polyvinyl Chloride concealed conduit with all fittings and accessories. This includes a pressed steel powder-coated sunken terminal box suitable for a Modular switch socket (minimum 50 millimeter deep and 1.6 millimeter thick sheet, suitable size) concealed in the wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/sockets/regulator, etc. This also includes the provision of a 1.5 square millimeter single core Flame Retardant Low Smoke Polyvinyl Chloride insulated multi-stranded copper conductor wire continuing as an earth wire connected to the earth dolly, etc., including cutting chases in the wall and making good disturbed surfaces of walls, ceiling, or floors, etc., by using Cement Mortar (1:3 mix), including fixing of the switch/socket/regulator, etc., complete as specified and as directed. (Note 1: Switches/sockets/regulators, etc., shall be measured and paid separately.)

Supplying and Fixing in replacement of Ding Dong bell, Alternating Current 230 Volts, complete as specified and as directed.

Supplying and Fixing Modular stepped type electronic fan regulator, flush type, on the existing phenolic laminated sheet etcetera, as required, heavy duty, 230 volts, complete as specified and as directed.

Supplying and Fixing in replacement, sheet metal enclosure Distribution Boards, double door, factory made, flush fixed, complete with 200 Ampere rated bus-bar, 240 Volts, single phase, 8 ways, including necessary brick work and plaster to match with the existing surface, complete as specified and as directed.

Supplying and Fixing in replacement, sheet metal enclosure Distribution Boards, double door, factory made, flush fixed, complete with 200 Ampere rated bus-bar, 240 Volts, single phase, 12 ways, including necessary brick work and plaster to match with the existing surface, complete as specified and as directed.

Supplying and Fixin

g in replacement Miniature Circuit Breaker, single pole, 6 to 32 Amperes, complete as specified and as directed.

Material and Labour for point wiring drawn in existing concealed conduit for one 3-pin socket outlet, 15 Amperes, on an independent board. The wiring is complete with 2.5 square millimeter (nominal cross-section area) single core Flame Retardant Low Smoke Polyvinyl Chloride insulated unsheathed and multi-stranded copper conductor cable, 1100 volt (Indian Standards Institution marked), drawn through an existing Polyvinyl Chloride concealed conduit with all fittings and accessories. This includes a pressed steel powder-coated sunken terminal box suitable for a Modular switch socket (minimum 50 millimeter deep and 1.6 millimeter thick sheet, suitable size) concealed in the wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/sockets/regulator, etc. This also includes the provision of a 2.5 square millimeter single core Flame Retardant Low Smoke Polyvinyl Chloride insulated multi-stranded copper conductor wire continuing as an earth wire connected to the earth dolly, etc., including cutting chases in the wall and making good disturbed surfaces of walls, ceiling, or floors, etc., by using Cement Mortar (1:3 mix), including fixing of the switch/socket/regulator, etc., complete as specified and as directed. (Note 1: Switches/sockets/regulators, etc., shall be measured and paid separately.)

Material and Labour for surface point wiring for one light point, fan point, or bell point controlled by one switch (using red, black, and green colour wires as colour coding) complete with 1.5 square millimeter (nominal cross-section area) single core Flame Retardant Low Smoke Polyvinyl Chloride insulated unsheathed and multi-stranded copper conductor cable, 1100 volt (Indian Standards Institution marked), drawn and including surface Polyvinyl Chloride conduit with all fittings and accessories, that is, pipe bend, pipe hook, elbow, junction boxes, etc. This includes a pressed steel powder-coated sunken terminal box suitable for a Modular switch socket (minimum 50 millimeter deep and 1.6 millimeter thick sheet, suitable size) concealed in the wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/sockets/regulator, etc. This also includes the provision of a 1.5 square millimeter single core Flame Retardant Low Smoke Polyvinyl Chloride insulated multi-stranded copper conductor wire continuing as an earth wire connected to the earth dolly, etc., including cutting chases in the wall and making good disturbed surfaces of walls, ceiling, or floors, etc., by using Cement Mortar (1:3 mix), including fixing of the switch/socket/regulator, etc., complete as specified and as directed. (Note 1: Switches/sockets/regulators, etc., shall be measured and paid separately.)

Supplying and Fixing in replacement Miniature Circuit Breaker, Double Pole, 40 Amperes, 240 Volts, 10 Kiloamperes, complete as specified and as directed.

Supplying and Fixing in replacement 40 to 63 Amperes Miniature Circuit Breaker, Triple Pole and Neutral, 415 Volts, complete as specified and as directed.

Supplying and Fixing in replacement of Sheet metal single pole and neutral enclosure, 240 volts, with a two-pin and earth plug and socket, complete with one single pole Miniature Circuit Breaker, capacity 20 Amperes, as specified and as directed (for Air Conditioner and geyser).

Supplying and Fixing in replacement LED tube light, 20 Watt (4 foot long), 6500 Kelvin, wall mounted, E-lite LED curve with high lumen batten, with efficacy not less than 100 lumens, with integrated electronic driver, complete with all accessories as specified and as directed.

Supplying and Fixing in replacement LED decorative Gate light or Garden lights, 20 Watt light fitting, with all accessories, including making connections by using a suitable size of Polyvinyl Chloride wire of any type, complete as specified and as directed.

Supplying and Fixing in replacement, LED street light fitting, powder coated, pressure die-cast aluminium compact, High power LED street light with heat resistant toughened glass, 25 Watt, with IP66 protection and impact resistance of IK07, including 10 Kilovolt Built-in Surge Protection Device. This includes a bracket made out of Galvanized Iron Pipe 40 millimeter, medium grade, 1.2 meter long, made to shape, with fixing clamps of Mild Steel Flat 40 x 6 millimeter, nuts and bolts, complete as specified and as directed.

Material and Labour for surface point wiring for one 3-pin socket outlet, 15 Amperes, on an independent board, complete with 2.5 square millimeter (nominal cross-section area) single core Flame Retardant Low Smoke Polyvinyl Chloride insulated unsheathed and multi-stranded copper conductor cable, 1100 volt (Indian Standards Institution marked), drawn and including surface Polyvinyl Chloride conduit with all fittings and accessories, that is, pipe bend, pipe hook, elbow, junction boxes, etc. This includes a pressed steel powder-coated sunken terminal box suitable for a Modular switch socket (minimum 50 millimeter deep and 1.6 millimeter thick sheet, suitable size) concealed in the wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/sockets/regulator, etc. This also includes the provision of a 2.5 square millimeter single core Flame Retardant Low Smoke Polyvinyl Chloride insulated solid copper conductor wire continuing as an earth wire connected to the common earth dolly, etc., including cutting chases in the wall and making good disturbed surfaces of walls, ceiling, or floors, etc., by using Cement Mortar (1:3 mix), including fixing of the switch/socket/regulator, etc., complete as specified and as directed. (Note 1: Switches/sockets/regulators, etc., shall be measured and paid separately.)

Supplying and Fixing in replacement for vertical sheet steel metal enclosure distribution boards, double door, factory made, three phase, 415 volts, 4 way, with 200 Ampere rating copper bus bar and Polyvinyl Chloride insulated copper wire of suitable size from the Moulded Case Circuit Breaker to the outgoing circuits. This includes one incoming Moulded Case Circuit Breaker and suitable outgoing Miniature Circuit Breakers circuits, comprising of three phase, four wire of suitable rating, complete with the following accessories as specified and as directed. (a) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz

Supplying and Fixing in replacement, Fresh Air fan, size 250 millimeter, Plastic body, 1200 Revolutions Per Minute, electrically driven, 230 volts, 50 Hertz, single phase, Alternating Current supply, featuring copper winding and dynamically balanced impeller for smooth and vibration free operation, complete with louvers, nuts for fixing the exhaust fan, and 3 foot long bolts and nu

ts for fixing louvers, including associated civil work, making provision for the wall opening, and provision of Polyvinyl Chloride insulated, flexible copper conductor cord of size 23/0.0076, three core, from the ceiling rose to the fan, complete as specified and as directed. (Note: Making suitable opening for fixing the air fan shall be deemed included in the quoted rate of the item.)

Supplying and Fixing in replacement, Exhaust fan of size 300 millimeter, Heavy duty, 1200 Revolutions Per Minute, electrically driven, 240 volts, 50 Hertz, single phase, Alternating Current supply, featuring copper winding and dynamically balanced impeller for smooth and vibration free operation, complete with louvers, nuts for fixing the exhaust fan, and 3 foot long bolts and nuts for fixing louvers, including associated civil work, providing the wall opening, and provision of Polyvinyl Chloride insulated, flexible copper conductor cord of size 23/0.0076, three core, from the ceiling rose to the exhaust fan for giving connection, complete as specified and as directed. (Note: Making suitable opening for fixing the exhaust fan shall be deemed included in the quoted rate of the item. Old items shall be deposited in the store yard.)