REPAIRS REPLACEMENT OF FILTERATION PLANT OF SWIMMING POOL AND CONNECTED ITEMS AND REPAIRS SERVICING OF SOLAR PANELS AND LIGHTS AT WELLINGTON STATION UNDER GE WELLINGTON

Painting of plant including inside painting work of pressure filter vessels 2 Nos using expoxy paint after primer coat and outside painting using aluminium paint after primer coat and pipe line of any dia upto 200mm for entire plant

Disconnecting the electric motor of capacity 10HP from position, strip opening the motor, taking out burnt copper winding wire from slots, cleaning the slots, rewinding the motor with suitable gauge of copper winding wire, insulating and vernishing, baking, including supply and replacing the bearings and refixing the motor with proper alignment with pump set, connecting up the electric connections testing, commissioning and transporting complete all as specified and directed.

Disconnecting the electric motor of capacity 15HP from position, strip opening the motor, taking out burnt copper winding wire from slots, cleaning the slots, rewinding the motor with suitable gauge of copper winding wire, insulating and vernishing, baking, including supply and replacing the bearings and refixing the motor with proper alignment with pump set, connecting up the electric connections testing, commissioning and transporting complete all as specified and directed.

Dismantling the defective centrifugal pump set, multi stage of capacity 10HP from foundation by opening of coupling and foundation bolts and transporting to workshop for repairing and reassembling after servicing and overhauling complete with oiling / greasing, lubricating the parts including repair/ replacement of worn out parts and installation commisioning and testing on full load complete all as specified and directed. Note: (i) The rate quoted for this item shall include labour charge only for maint repair and replacement of defective / unserviceable spares/ accessories. Spares are to measured and paid separately under subsequent items. (ii) Cost of other minor items/ spares such as nut, bolt washers, gaskets, paints etc which are not covered but required for effective functioning of the plant shall be deemed to be included in this item. (iii) The spares shall be of original make of pump as suitable as approved

Supply only CI impeller (one No) for centrifugal pump set, multi stage of capacity 10HP all as specified and directed.

Supply only bearing (2 Nos) for front and rear side of centrifugal pump set, multi stage of capacity 10HP all as specified and directed.

Supply only Key suitable for impeller of centrifugal pump set, multi stage of capacity 10HP all as specified and directed

Dismantling the defective centrifugal pump set, multi stage of capacity 15HP from foundation by opening of coupling and foundation bolts and transporting to workshop for repairing and reassembling after servicing and overhauling complete with oiling / greasing, lubricating the parts including repair/ replacement of worn out parts and installation commisioning and testing on full load complete all as specified and directed. Note: (i) The rate quoted for this item shall include labour charge only for maint, repair and replacement of defective / unserviceable spares/ accessories. Spares are to measured and paid separately under subsequent items. (ii) Cost of other minor items/ spares such as nut, bolt washers, gaskets, paints etc which are not covered but required for effective functioning of the plant shall be deemed to be included in this item. (iii) The spares shall be of original make of pump as suitable as approved

Supply only CI impeller (one No) for centrifugal pump set, multi stage of capacity 15HP all as specified and directed.

Supply only bearing (2 Nos) for front and rear side of centrifugal pump set, multi stage of capacity 15HP all as specified and directed.

Supply only Gun metal bush (2 Nos) for front and rear side of centrifugal pump set, multi stage of capacity 15HP all as specified and directed.

Supply only Key suitable for impeller of centrifugal pump set, multi stage of capacity 15HP all as specified and directed

Arresting water leakge from sluice valve of 80 mm bore, by refacing regrinding of sluice valve, repacking stuffing box of sluice valve spindle including taking apart and reassembling the same including replacing old check nuts with new one made out of MS/CI material with and including replacing perished gland packing, rubber gasker, bolts and nuts complete all as specified and directed

Arresting water leakge from sluice valve of 100 mm bore, by refacing regrinding of sluice valve, repacking stuffing box of sluice valve spindle including taking apart and reassembling the same including replacing old check nuts with new one made out of MS/CI material with and including replacing perished gland packing, rubber gasker, bolts and nuts complete all as specified and directed

Arresting water leakge from sluice valve of 150 mm bore, by refacing regrinding of sluice valve, repacking stuffing box of sluice valve spindle including taking apart and reassembling the same including replacing old check nuts with new one made out of MS/CI material with and including replacing perished gland packing, rubber gasker, bolts and nuts complete all as specified and directed

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth and getting out in hard/ dense soil for laying of GI/DI Pipe all as specified and directed

Returning filling in including spreading, leveling, watering and well ramming in layer not exceeding 25 Cms all as specified and directed

Removal of excavated surplus soil not exceeding 50 m and depositing where directed at al level not exceeding 1.5 m above the starting point all as specified and directed

Supplying & Laying unreinforced precast concrete cable cover ,Class LV, type I ,flat size 250 mm x150 mm x40 mm as in cable protection all as specified and directed.

Supply and spreading clean riddled excavated sand free from stone in trenches for cushioning all as specified for cable protection in trenches/ ducts complete all as specified and directed. Note:The punned down thickness shall only be measured

Taking up/ down carefully serviceable / unserviceable CI/DI pipe(including all fittings) with spigot and socket ends and joints, connections from the trenches of size of 100mm dia all as specified and directed.

Taking up/ down carefully serviceable / unserviceable CI/DI pipe (including all fittings) with spigot and socket ends and joints, connections from the trenches of size of 150mm dia all as specified and directed.

Taking up/ down carefully serviceable / unserviceable CI/DI pipe(including all fittings) with spigot and socket ends and joints, connections from the trenches of size of 200mm dia all as specified and directed.

Ductile iron pipe 100mm bore dia, spigot and socket ends, including specials class 'K-9" and including rubber gasket (push on) joints of same make of DI pipe having two sections of different hardness for spigot and socket pipes as in trenches complete all as specified and directed.

Ductile iron pipe 150mm bore dia, spigot and socket ends, including specials class 'K-9" and including rubber gasket (push on) joints of same make of DI pipe having two sections of different hardness for spigot and socket pipes as in trenches complete all as specified and directed.

Ductile iron pipe 200mm bore dia, spigot and socket ends, including specials class 'K-9" and including rubber gasket (push on) joints of same make of DI pipe having two sections of different hardness for spigot and socket pipes as in trenches complete all as specified and directed.

Aluminium alloy telescopic rod, top dia 30mm and bottom dia 28mm with detachable superior quality brush ISI marked of size 6 metre expanded upto 12 Mtr for brushing the entire area of swimming pool complete all as specified and directed. Make-Astral, Trios or equivalent

Supply only Chlorine Test kit of existing sample complete all as specified and directed

Supply only PH Test Kit of existing sample complete all as specified and directed

Taking down old unserviceable sluice valve and Supply and fix PN-1.60 sluice valve cast iron double flanged type non raising spindle with hand wheel and fixed by means of suitable bolts and nuts etc, after putting new rubber gasket etc for 80mm dia all as specified and directed.

Taking down old unserviceable sluice valve and Supply and fix PN-1.60 Non Return sluice valve cast iron double flanged type non raising spindle with hand wheel and fixed by means of suitable bolts and nuts etc,after putting new rubber gasket etc for 100mm dia all as specified and directed.

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp all as specified and directed.

Supply and fixing LED flood light 210 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

Taking down old unsv unserviceable MCCB, Supply and fixing MCCB of 4 pole 250Amps, 36 KA or higher capacity all as specified and directed.

Taking down old unsv unserviceable MCCB, Supply and fixing MCCB of 4 pole 160Amps, 36 KA or higher capacity all as specified and directed.

Taking down old unsv MCB and Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.(TPN 40 To 100 AMP) all as specified and directed.

Taking down old unsv MCB and Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.(TPN 25 To 63 AMP). all as specified and directed.

Sub main wiring with two single pole 6 sqmm (nominal area) stranded copper conductor FRLS PVC insulated and unsheathed cable drawn in and including non metalic PVC regid conduit medium grade of suitable size with all standard fitting , concealed , including one run of continuous PVC insulated stranded copper conductor FRLS cable 6 sqmm (nominal area) for earth continuty complete all as specified and directed. Note- Three runs of 6 sqmm copper cable and one run of PVC conduit willbe measured in one RM.

Round shape 18 watt 220 volts AC 6500K lumen output 2400, 30 cm dia surface panel type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed Make-Luker product code- LCL18NR or equivalent techno commercial make

Cleaning and removing all scales/ dirt / mud, sediment, silt from dug well at Singarthope,Ghai ground MRC and cleaning of wall holes, shurbs etc. , preparation of surface all as specified and directed. .cleaning the inside surfaces of the tank by scraping down walls & bottom surface using steel wire brushes to remove all disputaion/ fungus other micro organisms etc using light hammer & wire brushes taking out and removing sedimental loose dirt/mud sludge vegetation and other foreign meterial completely from the tank, disposal of all the waste/spoil to out of MD land at a place as specified by local bodies and washing repeatedly the inside surfaces of tank with water and washing with antibacterial solution and clean water thoroughly all as specified and as directed by Engr in charge following hygienic condition &complete all respect, as per reputed specialized process

Construction of brick masonry valve chamber 230 mm thick wall of 1200 mm x 1200 mm x 860mm ht internal size, for valves of size more than 100mm , necessary earth work and excavation in any type of soil, 150 mm thick PCC foundation in 1:4:8 type D2 using 40mm graded stone aggregate, brick work in walls with sub class B bricks built in CM 1:6, PCC Coping 75mm thick and bed blocks for embedding the angle iron hold fasts with PCC 1:2:4 type B -1 using 20 mm stone aggregates, rendering in CM 1:4, 15 mm thick finished fair and even without using extra cement, including provision of MS Sheet cover 2mm thick fixed to MS angle iron frame made out of 40mm x 40 mm 4 mm thick, two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces and locking arrangements with lock and key including taring to the embedded steel surfaces complete all as specifed and direted.

Material and labour for construction of brick masonry valve chamber 230 mm thick wall of 600 mm x 600 mm x 860 mm ht internal size, for valves upto 50mm size necessary earth work and excavation in any type of soil, 150 mm thick PCC foundation in 1:4:8 type D2 using 40mm graded stone aggregate, brick work in walls with sub class B bricks built in CM 1:6, PCC Coping 75mm thick and bed blocks for embedding the angle iron hold fasts with PCC 1:2:4 type B using 20 mm stone aggregates, rendering in CM 1:4, 15 mm thick finished fair and even without using extra cement, including provision of MS Sheet cover 2mm thick fixed to mS angle iron frame made out of 40mm x 40 mm 4 mm thick, two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces and locking arrangements with lock and key including taring to the embedded steel surfaces complete all as specifed and direted.

Material and labour for construction of brick masonry valve chamber 230 mm thick wall of 900 mm x 900 mm x 860mm ht internal size, for valves of size 80/100 mm , necessary earth work and excavation in any type of soil, 150 mm thick PCC foundation in 1:4:8 type D2 using 40mm graded stone aggregate, brick work in walls with sub class B bricks built in CM 1:6, PCC Coping 75mm thick and bed blocks for embedding the angle iron hold fasts with PCC 1:2:4 type B using 20 mm stone aggregates, rendering in CM 1:4, 15 mm thick finished fair and even without using extra cement, including provision of MS Sheet cover 2mm thick fixed to mS angle iron frame made out of 40mm x 40 mm 4 mm thick, two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces and locking arrangements with lock and key including taring to the embedded steel surfaces complete all as specifed and direted.

Taking up/ down carefully serviciable/ unserviceable 15mm dia GI Pipe and connections from the trenches or removal from walls, floors etc all as specified and directed.

Taking up/ down carefully serviciable/ unserviceable 20mm dia GI Pipe and connections from the trenches or removal from walls, floors etc all as specified and directed.

Taking up/ down carefully serviciable/ unserviceable 25mm dia GI Pipe and connections from the trenches or removal from walls, floors etc all as specified and directed.

Taking up/ down carefully serviciable/ unserviceable 50mm dia GI Pipe and connections from the trenches or removal from walls, floors etc all as specified and directed.

Taking up/ down carefully serviciable/ unserviceable 80mm dia GI Pipe and connections from the trenches or removal from walls, floors etc all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 15mm bore all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 20mm bore all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 25mm bore all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 50mm bore all as specified and directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 80mm bore all as specified and directed.

Rectifying leakage of 80mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Rectifying leakage of 50mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Rectifying leakage of 40mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Rectifying leakage of 25mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Rectifying leakage of 20mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Rectifying leakage of 15mm bore GI pipe line including excavation in mud (not exceeding 0.8m x 0.8m x 0.7m) and making arrangement for dewatering by using electric/diesel pump/manual additional labour including cutting,threading, and GI fittings like elbow, tee etc all as specified and directed.

Ductile iron specials such as bends, tapers, tee pieces (single and double branch) any type and angle/ radius and straight connecting piece but all ends socketed/ flanged of size 80, 100 to 150 mm dia bore complete all as specified and directed.

DI mechanical joint 80mm confirmiring to relevant latest IS code all as specified and directed.

DI mechanical joint 100mm confirmiring to relevant latest IS code all as specified and directed.

DI mechanical joint 150mm confirmiring to relevant latest IS code all as specified and directed.

Dismantling and taking out existing damaged / rusted valve pit cover of any size from valve pit chamber, not less than 1 M x 1 M and M & L for new valve pit coverof size not less than 1 M x 1 M made out from MS Angle iron of size 50 x 50 x 5mm frame with fixing the MS sheet of thickness 3 mm welded on MS angle complete including locking arrangement with two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Servicing / Repairs to existing Non clogging pump (suction sweeping pump) of any make, any capacity and head, Suction & Delivery 40mm/ 40mm. Installed at swimming pool . Repair of pumps comprises with following works:- a) Dismantling of pump completely without damaging any parts, degreasing and cleaning of parts and setting aside for inspection of serviceable parts. b) Re assembling the pump by using existing serviceable parts and new parts such as bearing set, bush, CI impeller, trolly wheels etc, including any other repair required for smooth functioning of pump complete. Note: Parts required for replacement shall be measured and paid separately.

Supply only DE and NDE Bearing suitable for Suction sweeping pump non clog type, Pump capacity 5HP (as per existing) all as specified and directed. Make of bearing SKF/TATA

Supply only Gasket set of Suction sweeping pump non clog type, Pump any capacity all as specified and directed..

Supply only CI Gland suitable for Suction sweeping pump non clog type, Pump any capacity all as specified and directed.

Repair carrying out complete deep cleaning of existing swimming pool including draining of water, removal of sludge, algae, dirt and debris; mechanical scrubbing of pool floor and walls; descaling of tiles; pressure jet cleaning; cleaning of skimmers, gutters, balance tank; inspection of all surfaces; minor crack filling with polymer mortar; minor tile repairs; re-grouting of joints; application of anti-algae and disinfectant treatment; refilling of pool and initial chemical balancing including labour, materials, tools and equipment complete all as specified and directed.

Servicing and maintenance of existing filtration plant including valves and piping; dismantling, cleaning, replacement of worn-out parts (gaskets, valves, seals), lubrication, trial run and ensuring proper functioning complete all as specified and directed.

Repair the UIS Sluice Valve of any size for back wash of the Rapid Sand Filter Old Type, Removing carefully and transporting to he Workshop repaireplacement unserviceable parts and servicing, conditioning the valve for continuous operations and refixing the same at existing location and testing the rapid sand filter for backwash and wash out complete all as specified and as directed. Note (1) Incase of any damage occured in any parts of Old Sluice Valve at e at the time of removing, the parts are not available in the market then it will be make in laith with the same material ie (Copper, Brass, Steel) and fixed the same in leu of damaged parts without any extra cost. (ii) In case of any U/S Mtrl not available in the market then it will made from laith and fixed properly The work will excecute and completed within one weak from remove the valve from the site.

Painting for elctric motar of capacity of 10HP to 15 HP with a coat of approved colour paint including inlet and outlet pipelines over a coat of redoxide primer on rusted part complete including prepration of old painted surface and writing MES number all as specified and directed.

Applying two coats of synthetic enamel paint over a coat of red oxide primer after preperation of surfaces of pipe lines of any size/type on surface/floors within the swimming pool ,pump house/ intstallation premises etc for sizes upto & including 250mm bore complete all as specified and directed. Note: Length include running connecting fittings such as bends, tees, crosses etc.

Fully Automatic Star Delta Starter 7.5 HP to 15 HP type ML 1.5 current rating 10 to 25 Amps in Sheet-Steel Enclosure with Single Phase Protection feature (Motor Rating AC-3 Duty, 415 V, 50HZ, 3 Ph) all as specified and directed. Make LK Cat No. SS94362 or equivalent in ABB/ Siemens.

Disconnecting, taking out and removing from trenches/ ducts/ sleeve/on pole/ wall etc existing LT UG XLPE insulated, armoured cable of any description, 95 sqmm 3.5 Core and in any position complete all as specified and directed. Note: Earth work shall be measured & paid separately under respective item.

Disconnecting, taking out and removing from trenches/ ducts/ sleeve/on pole/ wall etc existing LT UG XLPE insulated, armoured cable of any description, 70 sqmm 3.5 Core and in any position complete all as specified and directed. Note: Earth work shall be measured & paid separately under respective item.

Disconnecting, taking out and removing from trenches/ ducts/ sleeve/on pole/ wall etc existing LT UG XLPE insulated, armoured cable of any description, 50 sqmm 3.5 Core and in any position complete all as specified and directed. Note: Earth work shall be measured & paid separately under respective item.

Supplying, laying, jointing and testing XLPE insulated and PVC sheathed armoured LT cable, 1100 volts grade heavy duty with aluminium conductor of 95 sqmm 3.5 Cores laid in trenches/ pipe/ fixed on the wall etc complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated and PVC sheathed armoured LT cable, 1100 volts grade heavy duty with aluminium conductor of 70 sqmm 3.5 Cores laid in trenches/ pipe/ fixed on the wall etc complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated and PVC sheathed armoured LT cable, 1100 volts grade heavy duty with aluminium conductor of 50 sqmm 3.5 Cores laid in trenches/ pipe/ fixed on the wall etc complete all as specified and directed.

Burning out run lead joint of CI pipe line 100 mm dia bore all as specified and directed. Note: Lead shall be recovered by burning out joints carefully from the existing joints of the water mains and shall be the contractor’s property and credit recovery shall be made for the same.

Burning out run lead joint of CI pipe line 150 mm dia bore all as specified and directed. Note: Lead shall be recovered by burning out joints carefully from the existing joints of the water mains and shall be the contractor’s property and credit recovery shall be made for the same.

Burning out run lead joint of CI pipe line 200 mm dia bore all as specified and directed. Note: Lead shall be recovered by burning out joints carefully from the existing joints of the water mains and shall be the contractor’s property and credit recovery shall be made for the same.

Run lead joint for CI/DI spigot and socket pipe line and fittings of size 100mm dia bore all as specified and directed.

Run lead joint for CI/DI spigot and socket pipe line and fittings of size 150mm dia bore all as specified and directed.

Run lead joint for CI/DI spigot and socket pipe line and fittings of size 200mm dia bore all as specified and directed.

Servicing / repairs and testing of solar water heater and checking panel and replacement of spares etc. all as specified and directed. Note: (i) Spares to be changed shall be of same make as per existing. (ii) Spares will be measured and paid separately

Taking down old unservicable solar water vaccum tube and fixing new vaccum tube of existing model all as specified and directed.

Supply and replace toughened glass for solar collector of solar water heater complete all as specified and as directed.

Taking down old unservicable flat plate solar collector and supply and fixing new flat plate solar collector of existing model all as specified and directed.

Taking down old unservicable solar water heater drum and fixing new drum of existing model and capacity all as specified and directed.

Supply and fix heating element as per existing model with inbuilt thermostat for solar water heater all as specified and directed.

Supply and fill distilled water all as specified and directed.

Supply and fix Hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore complete all as specified and directed.

Supply and fix Hot water pipe duly insulated with glass wool and aluminium cladding 20 mm bore complete all as specified and directed.

Supply and fix Hot water pipe duly insulated with glass wool and aluminium cladding 25 mm bore complete all as specified and directed.

Battery lead copper of 50 sqmm as per sample (Red and Black colour) and taking down old unservicable battery lead all as specified and directed.

Battery terminal positive marking /negetaive marking of brass of existing size and taking down old unservicable battery terminal all as specified and directed

Taking down old unsv CFL solar street light fitting Supply and fixing LED Solar street light fitting 16 Watts including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Make- Panasonic/ Havells/ Philips

Taking down old unsv CFL solar street light fitting Supply and fixing LED Solar street light fitting 20 Watts including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Make- Panasonic/ Havells/ Philips

Taking down old unsv CFL solar street light fitting Supply and fixing LED Solar street light fitting 36 Watts including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified and directed. Make- Panasonic/ Havells/ Philips

Schedule of Credit (Minus) Rs. 93830.00 NOTE: Bidder shall insert credit amount of Rs. 93830.00 as rate in Green field under Col-5.

Please Enable Macros to View BoQ information