COMLPETION OF INCOMPLETE WORK FOR PROVISION OF OTM ACCN AND ALLIED FACILITIES (PACKAGE-2) IN MISSAMARI (ASSAM)

Amount

Lump sum price worked out by the contractor for BUILDING WORK as listed in Schedule ‘A’ Part-I of (Representing ________________% ______ _______________Percentage) @ ABOVE/BELOW the lump sum price of Rs. 13155529.89 (Rupees One Crore Thirty One Lakhs Fifty Five Thousand Five Hundred Twenty Nine and Eighty Nine Paise only) inserted by the MES in Schedule ‘A’ Part-I on Serial Page No. 35

Lump sum price worked out by the contractor for SITE CLEARANCE, AREA DEVELOPMENT, EXCAVATION AND EARTHWORK as listed in Schedule ‘A’ Part-II of (Representing ________________% ________ _____________ Percentage) @ ABOVE/BELOW the lump sum price of Rs. 26079176.85 (Rupees Two Crore Sixty Lakh Seventy Nine Thousand One Hundred seventy six and Eighty five paise only) inserted by the MES in Schedule ‘A’ Part-II on Serial Page No. 260

Lump sum price worked out by the contractor for INTERNAL ELECTRIFICATION as listed in Schedule ‘A’ Part-III of (Representing ________________% ____________________ Persentage) @ ABOVE/ BELOW the lump sum price of Rs. 4011656.30 (Rupees Forty Lakhs Eleven Thousand Six Hundred Fifty Six and Thirty paise only) Serial Page No. 273

Lump sum price worked out by the contractor for INTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-IV of (Representing ________________% _____________________Percentage) @ ABOVE/ BELOW the lump sum price of Rs. 249236.00 (Rupees Two Lakhs Forty Nine Thousand Two Hundred Thirty Six Only) inserted by the MES in Schedule ‘A’ Part-IV on Serial Page No. 275

Lump sum price worked out by the contractor for AREA DRAINAGE as listed in Schedule ‘A’ Part-V of (Representing ________________% _____ ________________Percentage) @ ABOVE/BELOW the lump sum price of Rs. 874754.30 (Rupees Eight Lakhs Seventy Four Thousand Seven Hundred Fifty four and Thirty Paise Only) inserted by the MES in Schedule ‘A’ Part-V on Serial Page No. 277

Lump sum price worked out by the contractor for SEWAGE DISPOSAL as listed in Schedule ‘A’ Part-VI of (Representing ________________% ________________ Percentage) @ ABOVE/ BELOW the lump sum price of Rs. 2202222.40 (Rupees Twenty Two Lakhs Two Thousand Two Hundred Twenty Two and Forty paise Only) inserted by the MES in Schedule ‘A’ Part-VI on Serial Page No. 279

Lump sum price worked out by the contractor for COMPOUND WALL FENCING & GATE as listed in Schedule ‘A’ Part-VII of (Representing ________________ % ___________________ Percentage) @ ABOVE/ BELOW the lump sum price of Rs. 1217777.10 (Rupees Twelve Lakhs Seventeen Thousand Seven Hundred Seventy Seven and Ten paise Only) inserted by the MES in Schedule ‘A’ Part-VII on Serial Page No. 282

Lump sum price worked out by the contractor for ROAD PATH & CULVERT as listed in Schedule ‘A’ Part-VIII of (Representing ________________% _____________Percentage) @ ABOVE/BELOW the lump sum price of Rs. 18337075.43 (Rupees One Crore Eighty Three Lakhs Thirty Seven Thousand Seventy Five and Forty Three paise Only) inserted by the MES in Schedule ‘A’ Part-VIII on Serial Page No. 287

Lump sum price worked out by the contractor for LIGHTENING PROTECTION as listed in Schedule ‘A’ PART-IX of (Representing _______________% _____________________Percentage) @ ABOVE/ BELOW the lump sum price of Rs. 63351.50 (Rupees Sixty Three Thousand Three Hundred Fifty One and Fifty paise Only) inserted by the MES in Schedule ‘A’ PART-IX on SERIAL PAGE No. 289

Lump sum price worked out by the contractor for EXTERNAL WATER SUPPLY as listed in Schedule ‘A’ Part-X of (Representing ________________% ___________________ Percentage @ ABOVE/ BELOW the lump sum price of Rs. 831833.20 (Rupees Eight Lakhs Thirty One Thousand Eighty Hundred Thirty Three and Twenty paise Only) inserted by the MES in Schedule ‘A’ Part-X on Serial Page No. 292

Lump sum price worked out by the contractor for EXTERNAL ELECTRIFICATION as listed in Schedule ‘A’ Part-XI of (Representing ________________% _____________________ Percentage) @ ABOVE/ BELOW the lump sum price of Rs. 6261196.32 (Rupees Sixty Two Lakhs Sixty One Thousand One Hundred Ninty Six and Thirty Two paise Only) inserted by the MES in Schedule ‘A’ Part-XI on Serial Page No. 303

SCHEDULE "A" PART-XII Miscellaneous works (External Electrification and External Water supply and other services)

Supplying , installation , testing & commissioning of cubical type Feeder Pillar floor mounted outdoor type ( IP 65 potection ) suitable for 415 V , 3 phase, 4 wire, 50 HZ A C supply system having front surface area .5 sq. mtr (app.) comprising of the followings :- (i) Enclosure (IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.14 mm thick for frame work and 4mm thick covers for gland plates , i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 300 Amp capacity extensible type TPN Aluminium bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required. (i) 1 no 160 A, 415 Volts TP MCCB (ii) 1 set of Phase indicating lamp with MCB (iii) 1 no 100A, 415 Volts 3P MCCB (iv) 1 nos 32A, 415 Volts 3P MCCB (v) 5 nos.32A,230 Volts DP MCB (vi) 7 nos.16A ,415 Volts DP MCB

Supplying , installation , testing & commissioning of cubical type Feeder Pillar floor mounted outdoor type ( IP 65 potection ) suitable for 415 V , 3 phase, 4 wire, 50 HZ A C supply system having front surface area 1 sq. mtr (app.) comprising of the followings :- (i) Enclosure (IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.14 mm thick for frame work and 4mm thick covers for gland plates , i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 300 Amp capacity extensible type TPN Aluminium bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required. (i) 1 no 40 A, 415 Volts TP MCCB (ii) 1 set of Phase indicating lamp with MCB (iii) 5 nos.16A ,415 Volts TP MCB (iv) 1 nos.10A ,230 Volts DP MCB Note : Provision for mounting astronomical switch and its allied accessories shall be made in the Feeder Pillar.

Supplying , installation , testing & commissioning of cubical type Feeder Pillar floor mounted outdoor type ( IP 65 potection ) suitable for 415 V , 3 phase, 4 wire, 50 HZ A C supply system having front surface area 1 sq. mtr (app.) comprising of the followings :- (i) Enclosure (IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.14 mm thick for frame work and 4mm thick covers for gland plates , i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 300 Amp capacity extensible type TPN Aluminium bus bars of high condutivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transpotable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required. (i) 1 no 40 A, 415 Volts TP MCCB (ii) 1 set of Phase indicating lamp with MCB (iii) 3 nos.16A ,415 Volts TP MCB (iv) 2 nos.10A ,230 Volts DP MCB Note : Provision for mounting astronomical switch and its allied accessories shall be made in the Feeder Pillar.

Design, Manufacturing, supplying, fixing in position, testing and commissioning of the following front operated front access 3.15 mm thick CRCA steel enclosure free standing, water, dust and vermin proof Feeder pillars with IP-65 protection hinged and lockable doors complete with interconnections copper crimping lugs, brass glands bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system. All live accessories part shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be of colour coded with Heat shrinkable PVC insulated sleeves. 1 nos. 40 A 415V, 4P MCCB of 16 KA.thermal magnatic releases. 1 set of Phase indicating lamp with MCB 100A TPN bus bars of aluminium alloy. 7 nos 16A, 415 Volts 3P MCB 10kA.( 6 For Road Lighting& 1 spare ) Note : Provision for mounting astronomical switch and its allied accessories shall be made in the Feeder Pillar 1 nos. 63 A 415V, 4P MCCB of 36 KA.thermal magnatic releases. 1 set of Phase indicating lamp with MCB 100 A TPN bus bars of aluminium alloy. 1 no 40 A, 415 Volts 3P MCCB 16kA.(For Admin. Bldg) 2 nos 32A, 415 Volts 3P MCCB 16kA.(1 for HAV & ORS & 1 spare) 2nos.32A\ 25,230 Volts DP MCB 15kA.(1 for Drying & Ironing & 1 spare) 8 nos.16A,230 Volts DP MCB 15kA.( 1 for JCO LIV,1 storage , 1 MT area,3 for parking , 1gaurd House & 1 spare)

Supplying , installation , testing & commissioning of cubical type Feeder Pillar floor mounted outdoor type ( IP 65 potection ) suitable for 415 V , 3 phase, 4 wire, 50 HZ A C supply system having front surface area 1 sq. mtr (app.) comprising of the followings :- (i) Enclosure (IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.15 mm thick for frame work and 4mm thick covers for gland plates , i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 300 Amp capacity extensible type TPN Aluminium bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transportable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to switch gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required. (i) 1 no 40 A, 415 Volts TP MCCB (ii) 1 set of Phase indicating lamp with MCB (iii) 3 nos.16A ,415 Volts TP MCB (iv) 2 nos.10A ,230 Volts DP MCB Note : Provision for mounting astronomical switch and its allied accessories shall be made in the Feeder Pillar.

Supplying , installation , testing & commissioning of cubical type Feeder Pillar floor mounted outdoor type ( IP 65 potection ) suitable for 415 V , 3 phase, 4 wire, 50 HZ A C supply system having front surface area 1 sq. mtr (app.) comprising of the followings :- (i) Enclosure (IP 65 protection) fabricated in compartmentalized design from CRCA sheet steel of 3.15 mm thick for frame work and 4mm thick covers for gland plates , i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade having 300 Amp capacity extensible type TPN Aluminium bus bars of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 sec, bottom base channel of MS not less than 100mm x 50 mmx 5 mm fabrication shall be done in transportable sections, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required. (i) 1 no. 100 A 415V, 4P MCCB . (ii) set of Phase indicating lamp with MCB (iii) 8 nos.16A ,230 Volts DP MCB (iv) 2 nos.32A ,230 Volts DP MCB (v) 3 nos.40A ,230 Volts DP MCB (vi) 1 nos.63A ,230 Volts DP MCB

Supply and install commessioning and testing transformer step down indoor / Outdoor type floor mounted, copper wound 3 phase 50 Hz, vector delta star oil cooled primary voltage 11000 volt, secondary voltage 433 with off load tap changer on primary side to vary secondary voltage + 7.5% of capacity 160 KVA complete with standard fittings including provision of filling of transformer oil all as per IS-2036 complete all as specifed and directed including the following:- (a) Breather filled with silcagel (b) Oil temp guage (c) Oil conservator tank with oil level indicator (d) Explosion vent/saftey release valve (e) Filling/drain and sampling valve (f) Air release valve. (g) B1 Directional roller (h) Name plate showing vector group/Tap changer system with voltage variation. Make - Alstom, Bhel, Crompton Greaves.

M&L for supply for laying jointing & testing of Ductile Iron (DI) pressure pipe of dia 250 mm with spigot and socket ends centrifugally cast (spun) class k -9, with other relevant standards & mettallic zinc coating following by a finishing layer of epoxy paint in outer side, suitable for push on joint (rubber gasket joint) in any length with inside cement mortor lining laid in trenches complete all as specified.

All as per item 9 but 150 mm dia complete all as specified.

All as per item 9 but 100 mm dia complete all as specified.

M&L for ductile iron fittings such as bends (any radius and angle) tapers any type(straight bend increasing decreasing or double socket etc) Tree pieces single branch 'Y' junction. Double branch, cross (all sockets or socket and soigot) collars, tails pieces with one end flanged(integrally cast) and one end socket. spigot and plug suitable upto 250 mm bore ductile iron pressure pipes, of K - 9 classification and push on flexible rubber gasket joints complete all as specified.

SCHEDULE 'A' PART-XIII RECTIFICATION OF DEFECTS OF EXECUTED WORKS (Page 311 to 316)

M&L, Machine cut kota stone slab flooring 20-25mm Thick over cement screed base laid and jointed With grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, Screed bed(1:4) or bedding layer of mortar 20 mm thick for laying floor finishes, for each 5mm thickness over or under 15mm

M&L, Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with Screed bed (1:4)or bedding layer of mortar 20 mm thick for laying floor finishes for each 5mm thickness over or under 15mm

M&L, rubbing and polishing complete Machine cut kota stone slab flooring 20-25mm Thick

M&L,rubbing and polishing complete, Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar

M&L, 75mm hard core on rammed earth (for plinth protection) broken to gauge and exc 63mm (broken stone)

M&L, 75mm thick pcc 1:3:6 type-C-2 in plinth protection 40mm graded aggregate with necessary form work

M&L, for laying PCC 1:2:4 (20mm graded aggregate) type B-1 Cement concrete in surface channels and drains

M&L, Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex-tra cement, including forms, moulds, mi-tred / stopped ends etc.

M&L, Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft/ loose soil

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L, brick work with sub class'B' bricks using old size bricks, straight or curved on plan exc 6 M mean radius built in CM 1:4.

M&L, for rendering 15mm thick in CM 1:6 on concrete surface of internal wall including finish even and smooth surfaces using without extra cement.

M&L, for rendering 10mm thick in CM 1:4 on fair face of brick work or concrete surface of internal wall including using without extra cement (toilet Vertical wall for Glazed tiles)

M&L, for rendering 20mm thick in CM 1:4 in two layer on cement conrete or brick work including finish even and smooth surfaces using without extra cement with using WPC (Extra for cement constant kg/sqm=6.77 & wpc is @ 3% / kg.) in Second layer of 10mm thick rendering. (WPC shall be measured separately).

WPC on external wall (Integral waterproofing compound) (Using for cement constant kg/sqm=6.77 & wpc is @ 3% / kg.)

M&L, Preparation of newly plastered or unplastered surface and applying three coats of white wash on ceiling.

M&L Preparing new plaster surface of walls and applying two coat of oil based Distemper over a coat of primer and two coat of cement based white wall putty

M&L, Preparation of newly plastered or unplastered surface and applying two coats of s weather proof paint to external surface. Apex ultima

S&F, Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc.complete as specified, Supplied and Fixed. Size of frame (165x60mm & 105 x 60 mm)

M&L, Cement concrete filling in pressed steel chowket and other similar works, using for 1:3:6 Type C-1 (20 mm graded aggregates)

S&F, Parliament hinges, aluminium alloy anodised and fixed (100mm)

S&F, Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work type -f (20X3) as specified

S&F, Sheet glass. Ordinary quality and glazing (4mm thick) with oil putty in square n exc 0.5 sq.m in each pane

M&L preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified

M&L, two coats of synthetic enamel paint on steel surfaces over 10cm width or girth over a coat of red oxide primer including preparation of new surfaces.

M & L ,Burnt clay profile tile of size not less than 200 x 150 mm with thickness not less than 7 mm and aesthetic corrugation laid over CM 1:3 and average thickness not less than 15 mm mixed with water proofing compound @ 3 % by weight of cement and jointed in CM(1:3) mixed with crude oil by weigth of cement provided

M&L for Roof Treatment, Aluminium paint over the APP membrane

M&L, 100mm thick pcc 1:2:4 type-B-2 in Ramp 40mm graded aggregate

M&L, Finishing cement concrete surface even and smooth(flooring)

M&L, 100mm thick pcc 1:4:8 type-B-2 in Flooring for ramp top surface 40mm graded aggregate

M&L, 150mm thick pcc 1:2:4 type-B-2 in floors 40mm graded aggregate

M&L, Surface dressing n.exe 150mm deep soft/ loose soil

M&L for cement concrete type C-2 (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in coping or similar works rounded or chamfered on edges including neccessary form work complete all as specified and directed.

M&L pcc 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in surface channel & drain complete allas specified & directed.

M&L for forming fair finished to drain or channel 30 cm inner girth ( inner girth only measured) in cement concrete using extra cement including forms , moulds/slopped ends etc complete all as specified & directed.

Add or deduct to item no. 6 for each 25 mm girth or part there of over or under 30 cm in girth complete all as specified & directed.

M & L for brick work with subclass "B" brick, laid flat, in drains, old size Bricks, beded and jointed in CM 1:6 and pointed in CM in 1:3 completed all as specified and directed.

M & L for brick work with subclass "B" brick, laid on edge, in drains, old size Bricks, beded and jointed in CM 1:6 and pointed in CM in 1:3 completed all as specified and directed.

M & L for precast Cement Concrete block masonry with solid blocks using type C1 1:3:6 ( using 20 mm graded aggregates ) exc 10 cm width & setting in cement mortar in cm 1:6 complete all as specified & directed.

M&L for 10 mm thick cement plaster on fair faces of blockwork or concrete surfaces in CM 1:6 complete all as specified & directed.

M&L, brick work with sub class'B' bricks using old size bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6.

M&L,for precast cement concrete type B0(1:2:4) mix using 12.5 graded stone aggregate for louvers and jalies 50 mm thick (measured solid) including all mouldings and steel reinforcement but excluding frame set in CM 1:4 complete all as specified & directed.

M&L,RCC M-25 in lintels, Beams, cantilevers, bressummers, lintels over 1.5m span using 20 mm graded aggreagate) complete all as specified & directed.

M&L, Form work to Rough finished flat to sides and soffits of floor or roof beams,lintels including supports overhangs etc also splays between floor and beams etc ,complete all as specified and directed

M&L, of TMT steel bars 6 to 8mm ,cut to length ,bend to shape,including cranking,bending spiralloy for hooping for columns,hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia confirm to IS 432 , complete all as specified and directed

M&L, for rendering 15mm thick in CM 1:6 on concrete surface on surface other than fair face of brickwork or on one side of lathing in CM 1:4 complete all as specified and directed

M&L, Preparation of newly plastered or unplastered surface of walls and two coat of colour wash over by coat of white wash complete all as specified and directed.(Compound wall)

M&L, 2 coats of synthetic enamel paint on steel surfaces over 10cm width or girth over a coat of red oxide primer including preparation of new surfaces.

M&L, steel bars 10 mm dia and over hooking ends and binding with and mild steel wire (annealed ) not less than 0.9 mm dia confirming to Fe-410

M & L 150 mm th(compacted thickness) WBM in 2 layer 75 mm each with broken stone agg (63 mm to 40 mm ) of grading & rolled & consolidated to required gradient camber level super elevation with 8 to 10 ton power roller complete all as directed ( each layer shall be measured seperate).

M& L FOR PRECAST cement concrete kerb stone 150 mm thick 1:2:4 mix type B1 (using 20 mm graded aggregate with ) plaine fare faces including chamfferd weathering throughting etc.and setting in cement mortar 1:6 comlete all as specified and directed.

M&L pcc (1:4:8) type D2 using 40 mm graded stone aggregate in foot path/ walk way surfaces finished even & fair without extra cement including use & waste of form work of 75 mm th completed

M&l for machine pressed precast conc interlocking paver block with grey cement and pigment any shape & size confirming to IS 15658-2006 of 60 mm thickness ,M-35 grd laid over & with coarse sand complete all as specified & directed

Cement concrete type B-1 (1:2:4) mix (using 20mm graded aggregates) as in flooring of 75mm thickness finished even and fair without using extra cement(Basket ball court)

Testing of Insulation test, Polirity test and earth continuity test of internal wiring(Admin Block-MCB TPN DB 6 way -01 No,Incoming MCB TPN Four pole 40 Amp-01 No and MCB SP 6-32Amp -18 Nos, ORs Living -MCB SPN DB 6 way -01 No,Incoming MCB SPN 32 Amp-01 No and MCB SP 6-32Amp -04 Nos) to be carried out as per CA/PS Clause 20.10.

M & L Painting of LT poles with one coat of red oxide primer and two coat of aluminium paint over exposed surface and two coats of bituminous paint over embedded portion and the portion above coping shall be painted in alternative bands of black and yellow colour (each band of 30 cm wide) by two coats of super enameled paint upto 1.6 m height complete all as specified.-57 Nos

SCHEDULE 'A' PART-XIV (SCHEDULE OF CREDIT)

Schedule of credit inserted by MES in Sch 'A' Part-XIV on Serial Page No. 315(R). Note : The amount is fixed. The contractor will enter Rs 2559194.19 (Rupees twenty Five lakh fiftynine thousand one hundred ninety four and nineteen paise only) in the Column 6. If bidder enters any other amount the amount shall be amended as Rs2559194.19 (Rupees twenty Five lakh fiftynine thousand one hundred ninety four and nineteen paise only).

RC Madan

MAA BHAGWATI ASSOCIATES

NARSINGH DEVELOPERS LLP

surendra infrastructure pvt ltd

M/s KASHMIRA SINGH BARMI AND SONS

DNS CONSTRUCTION COMPANY

VERMA BROTHERS

STAR CONSTRUCTION

Bidder Name

VERMA BROTHERS

surendra infrastructure pvt ltd

MAA BHAGWATI ASSOCIATES

RC Madan

DNS CONSTRUCTION COMPANY

STAR CONSTRUCTION

M/s KASHMIRA SINGH BARMI AND SONS

NARSINGH DEVELOPERS LLP

M/S SONIA ENTERPRISES