SPECIAL REPAIR TO BLDG NO. P-161 (SINGLE OFFRS DEGREE BLOCK) AND OR MD ACCN BLDG NO. 84 (1 AND 2) OF MT LINES AT CME

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm but not exc. 4.0 sqm each complete all as specified and directed.

Taking down chowkats or frames, not exc. 1.50 sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred, put to gether with glue pinned at joints complete all as specified and directed.

Taking down shutters only of size exc 1.00 sqm but not exceeding 4.00 Sqm each complete all as specified and directed.

S&F 30mm thick flush shutter, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S& F 2nd class hard wood 35 mm thick factory made glazed and skeleton shutters open rebated and prepared to recieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed.

S & F mild steel works as in bands, straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed.

M & L preparing surface of iron and steel, treating small articles such as stop, covers, gully, grating, holdfasts, end of posts area exc 0.1 Sqm each complete all as specified and directed.

M & L cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

M&L preparing new wood and wood based surfaces of any description, over 100mm width or girth and applying two coats of synthetic enamel paint (first quality) over a coat of pink primer, complete all as specified and directed.

S&F PVC solid door frame of size 50X47mm made out of 5.0mm plain colour PVC sheet reinforced with mild steel square tube as specified manufacturer’s instructions complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rails & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in the frame at site as per specifications and drawings, complete all as specified and directed.

S&F in repairs 4mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares of any size complete all as specified and directed.

S&F in repairs 3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares not exceeding 0.50 sqmtr each pane complete all as specified and directed.

M&L preparing old steel and iron surfaces of any descriptions, over 100mm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S & F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 .complete all as specified and directed.

S & F 150 mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F 300 mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks of mild steel wire staples, fixing etc. complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks of mild steel wire staples, fixing in repair etc complete all as specified and directed.

S&F in repair 150mm dia double legged door stopper of aluminium alloy with rubber complete all as specified and directed.

S&F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old window of any description complete all as specified and directed.

M& L 20 mm thick, granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed.

Rounding to edges of stone slabs, such as in steps, cooking platform, and other similar situation complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7 mm using purpose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of GI Grid work : Armstrong/Swastik/Techno Grid and Make E board Gypsum or equivalent approved .

S&F 12 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorate face veneers on both faces, fixed with screws to timber frame work including dismantling of existing wooden boarding complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or above ground level) all as specified and directed.

M&L 75mm thick PCC type D-2 (1:4:8) using 20mm graded aggregate as in sub base etc complete all as specified and directed

M&L 25 mm thick, type B-1, 1:2:4 (20mm graded stone aggregate) as in sub base etc complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6. complete all as specified and directed.

S & F vitrified ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

S & F coloured non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed.

M & L vitrified ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M& L rendering 10mm thick cement mortar in 1:4 as in backing coat for fixing wall tiles complete all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 350mmx250mmx7mm /450mmx350mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat complete all as specified and directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

Raking out joints /pointing to random rubble or polygonal rubble uncoursed or brought upto courses built in cement mortar complete all as specified and directed.

M&L raised pointing to random or polygonal rubble , uncoursed or brought upto courses in CM 1:4 including necessary scaffolding upto all floor complete all as specified and directed.

Dismantling tiling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed

All as per item No 42 above, but bedded in lime or cement mortar complete all as specified and directed.

M&L for roof tiles, mangalore pattern, interlocking at side joints laid dry complete all as specified and directed.

All as per item No. 44 above, but except tile complete

M&L for ridge tiles, mangalore pattern, set and jointed in CM 1:6 complete all as specified and directed.

All as per item No.46 above, but except mangalore pattern ridge

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm complete all as specified and directed.

M&L 2nd class hardwood clean sawn battens at 30cm centres of sectional area exc. 5 & not exc. 15 sqcm complete all as specified and directed.

All as per item No.49 above, but except battens complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and directed.

M&L second class hard wood clean sawn in scantling fixed in framed work complete all as specified and directed.

M&L preparing the surfaces of tiles batten any size and spacing prepared and treated all over (measured overall on one side only) spaces not deducted with two coats of creosote oil complete all as specified and directed.

Dismantling boarding, any description in any position with nails complete all as specified and directed.

M&L 2nd class hardwood clean sawn weather boarding, plain, 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

M&L preparing the surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and directed

S & F 15mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 20mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees , union etc and fixed complete to walls and ceilings or laid in floors complete all as specified and directed complete all as specified and directed.

..Ditto.. all as item No. 57 above, but refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed. Note : The old serviceable tubing obtained from sl item No. 118 hereafter.

All as per item No.56 above, but 20mm bore. Note : The serviceable tubing obtained from sl item No. 119 hereafter.

Cutting chases, pinning in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills, sunshades, shelves, lintels,etc and cutting chasesfor concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old pipe complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including dismantling old pipe complete all as specified and directed.

S & F in repairs 110 mm dia PVC (SWR) bends any radius, provided with access door complete as specified and directed.

S & F in repairs PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 110 mm bore provided with access door complete as specified and directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal 110mm bore, provided with access door complete as specified and directed.

S & F in reparis 75 mm dia PVC (SWR) bends any radius provided with access door complete as specified and directed.

S & F in repairs PVC (SWR) branch pieces, single (single Y) equal or unequal, 75 mm bore, provided with access door complete as specified and directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal 75mm bore, provided with access door complete as specified and directed .

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key, scrubbing down with water all as specified and directed.

M&L 15mm thick cement plastering on stone masonry surfaces in CM (1:4) finishing surfaces even and fair without using extra cement over and including 10mm thick dubbing out on irregular face of wall in CM 1: 4 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying complete wall with POP/wall putty for making smooth surfaces and applying two coats of oil bound distemper over a coat of primer all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying complete ceiling with 3mm POP/wall putty for making smooth surface and applying three coats of white wash over a coat of POP/wall putty all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M & L complete removal of existing treatment by scraping down of old decorative surface of walls with steel wire brushes of smoke spots, moulds, moss efflorecent salts and applying complete wall with 3mm POP/wall putty for making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

M & L complete removal of existing treatment from walls, filling the holes/cavities and plastering the surface required, cleaning and preparation of the surfaces and applying complete wall with 3mm POP/wall putty for making smooth surfaces and applying two coats of exterior emulsion paint 100% acrylic over a coat of primers as per manufacturers instructions complete all specified and directed. Note : The rate shall be quoted by the contractor including scafolding to carry out the work for height more than 10.00 mtrs.

M & L for preparation of old surface of ceiling and applying one coat of oil bound distemper complete all as specified and directed.

M & L for one coat of synthetic enamel paint over wooden surfaces including preparation of old surfaces over 10cm width or girth all as specified and directed

M & L for painting one coat synthetic enamel paint on steel surface including preparation of old surface of any description, over 10 cm width or girth not otherwise described all as specified and directed

M & L for cleaning the Ashlar masonry, RR Masonry surface and removing dirt, dust, bird dropping, grease, oil, algae, fungus, monkey beats, vegetable growth etc., including providing, applying and washing the surface with liquid Ammonia Chemical of 5% solution and other chemical cleaning agent as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacturer, with the help of required scrubbers and also cleaning with machine operated water jet mixed with desired quantity of fine silica where ever required, without causing any scratching/ damage to the stone surface and finally washing the surface with clean water with the help of pressure jet machine, complete in all respect, including taking all precautions to safeguard ventilators, windows, doors etc. by suitable covering so as to avoid any damage to the building/structure, all as per direction of Engineer-in-charge Note:- The rate quoted by the contractor shall deem to include for scaffolding to carry out the work for height of two storey building (Ground+one)

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white (including fixing bolts, flushing cistern and flush pipe) including provision of flush pipe, plastic seat cover for pedestal pan and CP health faucet including two way angle cock complete all as specified and directed.

S&F in repair brass chromium plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specifed and as directed.

S & F in repair brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stainless steel bracket guard and railing 60 cm long etc. complete all as specified and directed.

S&F in repair 15mm dia concealed stop valve chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair soap dish holder stainless steel complete as specified and directed by Engr-in-Charge. (Make :Jaquar or equivalent)

S&F in repair toilet paper holder stainless steel complete all as specified and directed.

S& F in repair brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed complete all as specified and directed.

S&F in repair 10 ltr capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair overhead shower 100mm dia round shape, single flow (ABS body chromium plated with grey face plate) with rabit cleaning system complete fixed to ceiling complete all as specified and directed. Make : Jaquar Cat No. DHS-1989 or equivalent as approved by GE.

Mirrior polishing on marble/ granite/ kota stone/ stone work where ever reqd to give high gloss finish complete all as specified and directed.

M&L cement concrete type E-2, 1:5:10 (40 mm graded stone aggregate) lean concrete as in sunkun floor for filling etc. complete all as specified and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sunkun floor complete all as specified and directed.

M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral WPC complete all as specified and directed.

S & F powder coated aluminium sliding windows three track with two glass shutters using 5 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete including taking down old window of any size all as specified and as directed. Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

M& L for plain colour wood grain printed PVC sheet 2 mm thick on to flush door used instead of plain colour PVC sheet using rubber based adhesive, supplying & fixing at site a per specification and directed.

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L polythene film black 50 micron laid in floor complete all as specified and directed.

S& F in repair wash hand basin mixer complete as specified and directed by Engr-in-Charge. ( Make: Jaquar or equivalent)

Dismantling water tanks and removing to store capacity exc 500 & n.exc 1000 ltrs complete all as specified and directed.

S&F 1000 ltr. capacity three layered rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I and directed.

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed.

M&L PCC 1:2:4 (Type B0 using 12.5 mm graded stone aggregate) as in levelling course to match the undulations of roof and in in coping, roof kerbs, fins including benching etc complete all as specified and directed

M&L 10 mm thick cement screed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab and vertical surface, finished even and smooth by using steel trowel complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by forced complete all as specified and directed. Four course roof treatment consists of as under :- (a) Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm. (b) Laying of APP based membrane as specified thickness and weight. (c) Applying one coat of bitumin grade 85/25 @ 1.2 Kg/Sqm. (d) Applying two coat of aluminium paint @ 100ml/sqm

M&L for light shade joint free Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directed

M&L for ceremic tiles coloured tiles 7 to 8 mm thick area of each tile not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directed

S & F glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10 mm thick rendering on stone masonry surfaces in CM 1:4 all as specified and directed.

M & L Rough dressed sand stone slab 30 mm thick flooring bedded and jointed in CM 1:6, and pointed in cement mortar 1:3

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No.118 above, but 20mm bore

S&F in repair vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling complete all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including seat cover complete all as specified and directed

S & F health faucet (ABS Body) mild steel CP suitable for 15 mm dia pipe with 1.25 mtr long flexiable tube and ABS wall hook incl making connections and fixed in postion complete in all respect as specified

Supply and fixing in repair Brass chromium plated shower rose 125mm size with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and directed.

Supply and fixing in repair Soap dish, approximate size 160x 60x90mm fixed to plug with CP brass screw and complete all as specified and directed.

S&F in repair 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type , screwed down high pressure, with or without lettered 'Hot' or 'Cold' woth long shanks and flynuts, screwed for iron pipe complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

M&L in repair 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item No.128 above, but 110mm complete all as specified and directed.

S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair stainless steel sink, made out of 1.00 mm thick sheet for kitched with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mm bowl size 410mm x 330mm x160mm all as specified and directed. Make: Nirali/Diamond/Blue King/Kingston/

S & F stainless steel plate rack of approved make including taking down old unserviceable all as specified and directed. Make :- Prayag P-346 31x30x10 inch plate rack

Resecuring or easing and adjusting without taking down of shutter from frame exceeding 2 sqm each complete all as specified and directed.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat. The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made steel windows with two shutter (Glass & Wiremesh) with side hung shutters including projecting type hinges with steel handles, 4mm thick glass, wiremesh grill and steel peg stay complete with glazing bars dovetailed or welded and painting with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer including taking down old unservicable complete all as specified and directed.

S&F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old ventilator with frame of any description complete all as specified and directed. (a) SP 20048 (b) Glazing clips 19352

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and directed.

M& L for 18/19 Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, Ditto

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed.

M&L barrel tower bolts stove enamelled black of size 200 mm complete all as specified and directed.

M&L barrel tower bolts stove enamelled black of size 150 mm complete all as specified and directed.

S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised , sliding door bolt with hasp , staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F galvanised steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Demolition of brick or stone/boulder masonry, built in cement mortar including all quoins, aarches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:4 complete all as specified and directed.

M & L cutting hole in brick walls/stone walls exc. one brick but not exc 2 bricks for any purpose and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

M&L for securing 3 mm glass sheet glass, ordinary quality, in squares n exc 0.5 sq. m each in existing metal frame glazed with putty/ beads including removing loose or decayed putty/ beads, painting /oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work

Racking out joints/pointing to random rubble masonry, polygonal rubble uncoursed or brought upto course complete all as specified and directed.

M&L keyed pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto complete all as sepcified and directed,

M&L 15mm thick cement plastering on concrete surfaces in CM (1:4) finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L PCC 1:2:4 type B-1(using 20mm graded crushed stone aggregate) in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed

M&L cement concrete 1:3:6 type C-2 (40mm graded stone aggregate) as in floors plinth protection, path etc 75mm thick smooth finished surface without using extra cement complete all as specified and directed.

M&L preparing old plastered surfaces of wall and applying two coats of oil bound distemper over one coat primer on walls complete all as specified and directed.

All as per item No.160 above, but one coat of cement base paint without wall care puttycomplete all as specified and directed.

All as per item No.160 above, but one coat of white wash on ceiling complete all as sepcified and directed.

M&L one coat of synthetic enamel paint over wooden surfaces including preparation of old surfaces over 10cm width or girth all as specified and directed by the Engineer-in-Charge.

M&L painting one coat of synthetic enamel paint on steel surface including preparation of old surface of any description, over 10 cm width or girth not otherwise described all as specified and directed by Engineer-in-Charge.

M&L for precast concete cover slab of sizes (600 mm x 450 mm x 75mm, 600 mm x 600 mm x 75mm and 900 mm x 450 mm x 75mm thick) for man holes with provision of collar all around to house the cover slab and collar fixed to wall of manhole in cement mortar 1:6 having smooth surface finish complete all as specified and directed by Engineer-in Charge.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc all as directed

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

M&L for point wiring with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc for the following :-

One light point controlled by one switch

One fan/exhaust fan point controlled by one switch and regulator

Socket outlet, three pin 5 Amps on the same board

Socket outlet, three pin, 5 Amp, independent

All as per item No.168 above, but for one multipin 5 amps socket outlet on independent board

All as per item No.168 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board.

All as per item No.168 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board.

S & F switch piano, flush type, single pole one way 5 amps complete all as specified and directed.

S & F switch piano, flush type, single pole one way 15 amps complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 amps flush type complete all as specified and directed.

S & F socket outlet 5 in 1, 5 pin, 15 amps flush type complete all as specified and directed.

S & F bell push flush type single pole one way 5 amps complete all as specified and directed.

S & F ceiling rose, 3 terminal PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

S & F lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complete all as specified and directed.

M&L in replacement of LED lamp 9 watt complete all as specificed and directed.

S & F in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed.

S & F in replacement Call bell ding dong AC, 230 Volts, single pole complete all as specified and directed.

S&F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 No PVC square blocks incl taking down old UNSV fitting. Make- Havells cat No LUMILINEBS20WLED830SPCWH or equivalent of Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar/ C & S / Bentec India Ltd./ Luker.

S & F Decorative ultra slim with polycarbonate housing with high lumen output environmental friendly, energy efficient ready to use pack surface and wall mounted LED batten (LED tube light fitting complete 10W) with integrated electronic driver and 02 No PVC square blocks incl taking down old UNSV fitting.

S&F building security LED light fitting 25 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 including suitable size bracket incl taking down old UNSV one. Make - Havells cat No ENDURASUNDOWNSL25WLED765PASYBOPCIHD or equivalent of Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar/ C & S / Bentec India Ltd./ Luker.

S & F PVC cable ducts 75 x 45 mm with all accessories for fixing of sub main wiring drawn through cable duct along wall complete including taking down old existing all as specified and directed.

M&L for sub main wiring with two run of 4 sqmm single core multi stranded PVC insulated and unsheathed copper conductor of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC conduit of desired colour not less than1.2 mm thick and 25 mm wide & 4 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and directed incl taking down old unserviceable one.

S&F enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

Taking down celing fan of any size after disconnecting the wire from existing ceiling rose and deposited to MES Store (AGE E/M sub divn) and Supply and fixing ceiling fans complete with blades, down rods,regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Taking down electric water heater (geyser) of any 25/50 ltr capacity and refixing the same after repair alongwith connected accessories such as PVC connection pipe, fastner etc complete all as specified and directed. Note : cost for spare parts required for repair of geyser is deemed to be inclusive in the unit rate of this item.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as specified and directed.

S&F in replacement load line vertical TPN distribution board 4 way including 1 incommer MCCB of 125 Amps 4 pole double door IP-43 protection, powder coated, IK08 with provision of suitable size bus bar and cable management kit complete all as specified and directed. Make : Indoasian cat part No 811888 or eqlnt in Hager/Havells/Legrand

S & F MCB distribution board Double door SPN 240 volts 6 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one complete all as specified and directed.

S & F MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one complete all as specified and directed.

S & F MCB SPN 40 to 63 Amps, 230 V, AC incl taking down old unserviceable one complete all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI lead 4 mm dia as earthing lead connecting to equipment by means of GI bolts & nuts and washers of steel after welding of GI wire to earth eletrode to the full length of earth plate, 15 mm dia GI tubing light grade protection pipe upto last point with provision of charcoal and salt etc all as per electrical plate No-3 of SSR part-I 2009 including PCC 1:3:6, type C-1 earth chamber of out dimension 54x54x30 cm and internal dimension 30x30x30 cm with RCC 1:2:4 type B1 cover of size 54x54x10 cm, reinforced with 6 mm dia mild steel round bars @ 15 cm c/c both ways and 8 mm dia mild steel round bars handle, watering with GI pipe 20 mm dia (medium grade) & MS funnel and wire mesh, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed.

Taking down old ceiling fan any size or any type and deposited to AGE E/M store for necessary disposal action complete all as specified and directed.

Taking down single phase electric meter and refix the same after calibration and necessary repair on wooden board complete all as specified and directed. Note : Quarter wise last meter reading shall be noted by the contractor and submitted AGE E/M office for onward submission to BSO.

Supply and fixing LED tube light fitting surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, 2 feet, 10 watt 220 V AC including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F decorative wall light fittings (bracket light), CITY 3 made up of polycarbonate suitable for 10 watt LED lamp incl LED lamp incl taking down old UNSV one.

M&L for sub main wiring with two run of 4 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLSH cable 1100 volt electrical grade in and including PVC casing caping not less than 20mm wide & 4sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed.

S&F MCB distribution board double door 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm complete all as specified and directed.

M&L for LED lamp 9 watt complete all as specificed and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including taking down old existing one and deposited to AGE E/M store yard.

vishalconstruction

N AND G CONSTRUCTION