SPECIAL REPAIR TO C PLATOON (BLDG NO P-521) OF CTW AT CME PUNE

Amount

S&F Framed work such as roof trusses(framed), trusses purlins, crane gantries , rails and fastenings and heavy bracket framing(beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W(Gde E-250) Quality A complete all as specified and directed.,

S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W(Gde E-250) Quality A complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for and complete all as specified and directed

Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide primer complete all as specified and directed

Dismantling of plain or corrugated steel heeting any gauge, thickness, including nainital or similar pattern roof covering

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.

Dismantling water tanks and removing to store capacity exc 500 & n.exc 1000 ltrs complete all as specified and directed.

S&F For 750 ltr. Capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

M&L 10 mm thick cement screed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab and vertical surface ,finished even and smooth by using steel trowel complete all as specified and directed.

Removing existing/old damaged roof treatment of any (Brick tiles and Mudfuska) description by scrapping with using wire brush and removing the same from the site(s) to outside MD land, complete all as specified and as directed by Engr-in-Charge. Note: Dismantling all water tanks carefully and after roof treatment connect all tanks during working time. If any tanks, float valves and GI pipes damaged, contactor should replace the same (upto all storeys) without any extra cost.

M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( wt not less than 150 gms /sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 ltr/Sqm by forced complete all as specified and directed.

Four course roof treatment consists of as under :-

Applying one coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr per sqm.

Laying of APP based membrane as specified thickness and weight.

Applying two coat of aluminium paint @ 100ml/sqm

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete(unreinforced ) in ground floors and pavings not exceedidng 15cm thickness(below ;or aboved ground level) all as specified and directed.

M&L for 75mm thick PCC type D-2 (1:4:8) using 20mm graded aggregate as in sub base etc complete all as specified and directed

M&L For 25 mm thick, type B-1, 1:2:4 (20mm graded aggregate) as in sub base etc complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. Complete.

M& L Fof rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

M&L for glazed ceramic coloured tiles in verticle surface 350mmx450mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed,

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No 22 above but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement to match complete over and including 10mm thick cement screed in CM 1:4 complete all as specified and directed.

M& L For 20 mm thick ,Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed..

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

Roundidng to edges of stone slabs , such as in steps, cooking plateform, and other similar situation complete all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No 27 above, but 20mm bore

S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specifeid and directed.

S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Refixing 15mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed

All as per item No 31 above, but 20mm bore.

S & F under counter wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE.

M & L for half stall ceramic urinal pastel coloured of size 720x485x310mm (Make - Hindware Cat No. 60006 or equivalent approved make indicated in list of make in tender) including Urinal toughned glass / Marble / Granite including grinding, polishing, rounding/moulding/chamfering edges), brass cp bottle trap, electric operated auto censor / Push cock (Including spraders ) flushing arrangements. (Make Hindware Cat No. 500963 or equivalent approved make indicated in list of makes in tender) complete including taking down old u/s one complete all as specified and directed. Note : Type of partition will be decide by Engr-in-charge as per sitr requriment 2) Type of flushing arrangement will be decide by Engr-in-charge. Note : The rate quoted by the contractor is including the connection push cock & spraders.

S&FVitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)including seat cover complete all as specified and directed

S&F in repair 10 ltr capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F For in repair brass chromimum plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specifed and as directed.

S & F For brass chromium plated, 15 mm bore healthfoucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and as directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed.

M&L cement concrete type E-2, 1:5:10(40 mm graded aggregate)lean concrete as in sunkun floor for filling etc. complete all as specified and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4(20mm graded aggregate) as in sunkun floor complete all as specified and directed.

Cutting chase, pining in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chasesfor concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all as directed.

M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Supplied only WPC

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L Polythene film black 50 micron laid in floor complete all as specified and directed.

S&F in repair 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No 49 above but 110mm complete all as specified and directed.

S&F in repair 75mm PVC(SWR) bend any radius complete all as specified and directed

All as per item No 51 above but 110mm dia complete all as specified and directed.

S&F in repair 75mm PVC(SWR) junction single(single T) equal or unequal complete all as specified and directed.

All as per item No 53 above but 110mm bore of pipe complete all as specified and directed.

M&L in repair 75mm PVC(SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item No 55 above but 110mm complete all as specified and directed.

S&F in repair 75mm PVC(SWR) vent cowl complete all as specified and directed.

All as per item No 57 above but 110mm complete all as specified and directed.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia , D type 60cm long between flanges complete all as specified and directed.

S&F For sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steel bracket guard and railing 60 cm long etc. complete all as specified and as directed.

S& F in repair Soap dish holder complete as specified and directed by Engr-in-Charge. (Jaquar

S&F Toilet paper holder

S& F Brass CP Wash basin mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

S& F Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

Taking down chowkats or frames with shutter(without taking off shutters from the frames) not exc 1.5 sqm each and removing from sitecomplete all as sepcified and directed.

All as per item No 66 above but exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred,put together with glue pinned at joints including taking down chowkats with shutters complete all as specified and directed

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as spfd.

M&L for preparing new surface of wood of any decription , not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all, as specified and directed.

Mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

Preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc 0.1 Sqm each complete all as specified and directed.

Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as spd.

Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc including taking down old ventilator etc. complete all as specified and directed.

S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as spd .

M&L barrel tower bolts stove enamelled black of size 200 mm complete all as spd .

M&L barrel tower bolts stove enamelled black of size 150 mm complete all as spd .

S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed.

S&F 300mm long Aluninium alloy, anodised , sliding door bolt with hasp , staple,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, fixing and repair etc, complete all as specified and as directed.

Demolition of brick or stone/boulder masonary , built in cement mortar including all quoins, aarches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonary surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M&L 15mm thick cement plastering on concrete surfaces in CM (1:4) finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying complete wall with 3 mm POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coat of Oil Bond distermper white or tinned over an coat of primer on walls, etc all as specified and directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots, moulds, moss effloerent salts and treading oil and greasy spots and applyuing one coat of white (lime) wash complete all as spec ified and directed by Engineer-in-Charge

All as specified in Item No 93 above but applying one coat of white wash on ceiling.

M & L for one coat of synthetic enamel paint over wooden surfaces including preparation of old surfaces over 10cm width or girth all as specified and directed

M & L for painting one coat synthetic enamel paint on steel surface including preparation of old surface of any description , over 10 cm width or girth not otherwise described all as specified and directed Note:- The rate quoted by the contractor shall deem to include for scaffolding to carry out the work for height of ten storey building (Ground+nine)

M & L for complete removal of existing treatment from walls, filling the holes/cavities and platering the surface required, cleaning and preparation of the surfaces and applying two coats of exterior emulsion paint 100% acrylic (Apex) as per manufactured instruction complete all specified and directed. Note:- The rate quoted by the contractor shall deem to include for scaffolding to carry out the work for height of ten storey building (Ground+two)

M&L PCC 1:2:4 type B-1(Using 20mm graded crushed stone agg) in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed

All as per item No 93 above but two coat of cement base paint without wall care puttycomplete all as specified and directed.

All as per item No 93 above but two coat of white wash on ceiling complete all as sepcified and directed.

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decoirative type curtain rods including brackets for fixing curtain rod all as specified and as directed.

S&F in repairs brackets powder of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge all as specified and as directed.

M & L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete.

M&L cement concrete 1:3:6 type C-2 (40mm graded aggregate) as in floors plinth protection, path etc 75mm thick smooth finished surface without using extra cement complete all as specified and directed.

Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below ;or aboved ground level) all as specified and directed.

M&L For 25 mm thick, type B-1, 1:2:4 (20mm graded aggregate) as in sub base etc complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

M& L Fof rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

Virified Ceramic tiles 8 mm to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directd.

Virified Ceramic tiles 8 mm to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directd.

S & F powder coated Aluminium sliding windows three track with two glass shutters using 4 mm thick glass tinted Modi guard and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, Alumini cleat, PVC track, bearing, handle lock rubber beading, etc complete including taking down old window of any size. Note Size of aluminum sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

Taking down ceiling fans any type/sweep 230 V AC and refixing after cleaning and making connection complete all as specified and directed.

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface type with PVC modular white cover plate for mounting fittings such as switches, sockets, fan regulators etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc

All as per item No.114 above, but for one multipin 5 amps socket outlet on same board with other switch complete all as specified and directed.

All as per item No.114 above, but for one multipin 5 amps socket outlet on independent board complete all as specified and directed.

All as per item No.114 above, but for one light point controlled by 2, 2 way switch complete all as specified and directed.

All as per item No. 114 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board complee all as specifed and directed.

S & F in replacement ceiling rose, 3 phase PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

S & F in replacement lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complee all as specifed and directed.

S&F in replacement switch Modular, one way 6 amps, 1 module with suitable plate and cover complete all as specified and directed.

S&F in replacement switch Modular, two way 6 amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F in replacement switch modular one way 16 amps, 1 module with suitable plate and cover complete as per existing make and model all as specificed and directed

S&F in replacement socket modular 6A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

S&F in replacement socket modular 6A/16A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model all as specified and directed

S&F in replacement modular fan regulator step type 120W, 2 module with suitable plate and cover complete as per existing make and model all as specified and directed.

S&F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 No PVC square blocks incl taking down old UNSV fitting.

S&F surface and wall mounted LED batten (LED tube light fitting 10W), extruded aluminium housing provided for efficeient heat dissipation with polycarbonate diffuser & integrated electronic driver alongwith LED tube 10 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting.

S&F endura gugby NEON- IP 65 environmental friendly, ultra modern energy saving surfae mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 10 Watt incl taking down old UNSV fitting.

S&F building security LED light fitting 25 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 incl taking down old UNSV one.Make - Havells cat No ENDURAPEARLSL25WLED757SASYTOPC or equivalent of Philips/Bajaj

M&L for sub main wiring with two run of 6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC casing caping of desired colour not less than 1.2 mm thick and 25 mm wide & 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one.

All as per item No 131 above but size 10 Sqmm four runs and with one run 10.0 sqmm FRLSH copper wire for earth continuity including taking out old unsv one.

S&F in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt incl taking down old UNSV one.

S&F in replacement MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc incl taking down old unserviceable one.

S&F in replacement MCB distribution board double door 240 volts 4 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

S&F in replacement MCB distribution board TPN 4 way double door 415 volts and making good to disturbed surfaces of floors walls incl taking down old unserviceable one.

S & F in replacement MCB SP 6 to 32 Amps, 230 V AC incl taking down old unserviceable one.

S & F in replacement MCB SPN 32 Amps, 230 V, AC incl taking down old unserviceable one.

S & F in replacement MCB SPN 63 Amps, 230 V, AC incl taking down old unserviceable one.

S & F in replacement MCB TPN 63 Amps, 230 V, AC incl taking down old unserviceable one.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion incl taking down old unsv.

S&F LED lamp 9 watt complete all as specified and directed.

S & F exhaust fan 250 mm sweep PVC body ,230V with blades and frame with louvers complete including provision of 3 core PVC insulated sheathed 1100 volts grade flexible cable with stranded copper conductor from ceiling rose to fan, length as per requirement at site also arrangement to mount the fan as per requirement complete all as directed by EIC..

S & F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers including provision of 3 core PVC insulated sheathed 1100 volts grade flexible cable with stranded copper conductor from ceiling rose to fan, length as per requirement at site also arrangement to mount the fan as per requirement complete all as directed by Engr-in-Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including taking down old existing one and deposited to AGE E/M store yard.

Taking down electric water heater(geyser) of any 25/50 ltr capacity and refixing the same after repair alongwith connected accessories such as PVC connection pipe, fastner etc complete all as specified and directed.

S&F table lamp metal body adustable type having mounting arragement on wall/table including lamp 9 watt complete all as specified and directed.

AJINKYA VIKRAM GAIKWAD

Mukund Engineers and Contractors

vishalconstruction

Aakar Construction

BSK Construction

Intime Commotrade Pvt Ltd

SPS TRADING