8936-NIT-81-21-22 ADDN/ALTN OF MD ACCN No. P-04, P-05, P-06, P-08 AND P-10 AT MANOJ PANDAY ENCLAVE, SPL REPAIR INTERNAL ELECTRIFICATION OF BLDG P-29 OF 10 CSR AND P-119 OF 10 TAC UNDER AGE BR-V AND AGE E/M OF GE NORTH BATHINDA AT BATHINDA MIL STN

Amount

SCHEDULE 'A' B/R Works

Taking down chowkhats or frames with shutters (without taking off shutters from the frames, wooden/PVC doors/steel ventilator) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Demolition of cement concrete reinforced of any discription and in any position, like roofs, floors (other than ground floors), beams, staircases, landing, chajjas, fins, facia and similar suspended works, including reinforcement cut as required to facilitate demolition and prepare the surface to casting chajja, slabs, fins, facia etc and including removing rubbish material from site and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-charge.

Material and labour for PCC ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Material and labour for 40 mm thick damp proof course in cement concrete (1:2:4) type B0 using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary form work and including mixing of WPC in mortar @ 3%, complete all as specified and as directed by Engineer-in- charge.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in beams, cantilevers, bressummers., lintels, cills, steps; seismic and other similar bands complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Material and labour for reinforced cement concrete (1:2:4) (nominal mix) type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule.

Form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick (horizontal or sloping) fair finished complete all as specified and as directed by Engineer-in- charge.

Form work to flat sides and soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs, sides of chajjas etc and similar works rough finished flat surfaces complete all as specified & directed by Engineer-in- charge.

Material and labour for hard core of broken bricks of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for plastering 15mm thick in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 5mm thick in cement mortar (1:3) on any face of ceiling, finished fair and even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

Material and labour for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed by Engineer-in- charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose)

Material and labour for 75mm thick cement concrete ( 1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by Engineer-in-charge.

Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in flooring, hard standing, plinth protection/path etc. finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of wall by applying 3mm thick birla or JK wall care putty on wall surfaces even and smooth and applying two coat plastic emulsion paint on plastered surfaces over a coat of primer whitening complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of ceiling by applying 3mm thick birla or JK wall care putty on wall surfaces even and smooth and applying two coat oil emulsion distemper on plastered surfaces over a coat of primer whitening complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of wall by applying 3mm thick birla or JK wall care putty on wall surfaces even and smooth and applying two coat of weather exterior emulsion paint on plastered surfaces over a coat of primer whitening complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixing, factory made steel ventilators all as per IS 1038/83, with top hung shutters including hinges, suitable steel handle, steel peg stay, fixing lugs in PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) complete all as specified & as directed by Engineer-in- charge.

Supply & fixing and cutting as per size requirement 3mm thick sheet glass ordinary quality in squares/retangular not exceeding 0.5sqm in each pane and fixed in any type of doors / windows / ventilators (openable/fixed type) with fixing material complete all as specified & directed by Engineer-in- charge.

Supply & fixing galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staples complete all as specified & directed by Engineer-in- charge.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Solid PVC Door Frame of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 150mm long, aluminium anodised, barrel tower bolt of extruted section complete all as specified & directed by Engineer-in-charge.

Supply and fixing 100mm long, Butt hinges, medium weight, cold rolled mild steel complete all as specified & directed by Engineer-in-charge.

Supply and fixing 125mm long Aluminium handles, cast type, anodised complete all as specified & directed by Engineer-in-charge.

Returning and filling including spreading, leveling watering and well ramming in layers not exceeding 25cm thick in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge.

Material and labour cutting into existing manholes/septic tank for connecting new drain upto 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round to 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished, and reforming benching as required complete all as specified & directed by Engineer-in-charge.

Material and labour for cement concrete (1:3:6), type C2 using 40mm graded stone aggregate as in bed of drain pipe of size 150mm bore (internal) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in- charge.

Material and labour for 150mm bore (internal dia) salt glazed stone ware (SGSW) drain pipe, grade ‘A’, laid on concrete bed to required slope in trenches, jointing with packed spun yarn and in cement and sand mortar (1:1) and tested, complete all as specified and directed by Engineer-in-Charge. (Note : Excavation, earrh work and concrete bed shall be measured and paid separately under appropriate item of BOQ.)

Material and labour for Salt-glazed stoneware (SGSW) gully traps, 150mm x 150mm size, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as directed ) and making good disturbed surfaces of walls including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as directed) and making good disturbed surfaces of walls including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge.

Supply and fixing Cast iron floor trap 100mm bore, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate complete all as specified and as directed by Engineer-in- charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern) single piece WC with UF soft close seat cover hinges fixing accessories set and accessories set size 365mm x 655mm x 760mm complete all as specified and as directed by Engineer-in- charge. Make: Jaquar cat part No. LYS-WHT-38853S or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing vitreous china wash hand basin, white colour, of size 590mm x 490mm x 185mm excluding taps, but including fancy type 32mm waste coupling and waste pipe, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part LYS-WHT-38801 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in repair vitreous china wash hand basin, white colour, of size 590mm x 490mm x 185mm excluding taps, but including fancy type 32mm waste coupling and waste pipe, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part LYS-WHT-38801 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing Soap dish, vitreous China white, approximate size approximate size 160mmx160mmx90mm, including fixing to wall with CP screws and PVC plug complete all as specified and directed by Engineer-in-Charge.

Supply & fixing brass chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug, bracket with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in repair brass chromium plated tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug, bracket with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

Supply & fixing corner glass shelf with brackets, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part CAN-1173 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing cromium plated towel ring, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part AQN-7721 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in repair cromium plated towel ring, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part AQN-7721 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing cromium plated toilet paper holder, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part AHS-1553 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in repair cromium plated toilet paper holder, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part AHS-1553 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing cromium plated wall mixter three in one system with provision for both and over head shower complete with 115mm long bend pipe connecting legs & wall flange (with out hand & over head shower, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part SOL-6281 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing in repair cromium plated wall mixter three in one system with provision for both and over head shower complete with 115mm long bend pipe connecting legs & wall flange (with out hand & over head shower, complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part SOL-6281 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply and fixing in repair concealed stop cock cast copper alloy, chromium plated, fancy type, long shank and cup, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock shall be as given in SSR or in relevant IS.

Supply and fixing stop valve/angle valve cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in repair stop valve/angle valve cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in repair gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS.

Supply and fixing bib tap cast copper alloy, chromium plated with crutch or butterfly handle with capstan head, wall flange, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in repair bib tap cast copper alloy, chromium plated with crutch or butterfly handle with capstan head, wall flange, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing hand shower (health faucet) ABS body including 1.2 meter long 8mm dia flexible tube and including wall hook, complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ALD-CHR-593N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing in repair hand shower (health faucet) ABS body including 1.2 meter long 8mm dia flexible tube and including wall hook, complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ALD-CHR-593N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply and fixing in repair 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge.

Supply & fixing cromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Supply and fixing mixer valve 15mm bore, brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for WHB or fixed to wall, screwed down for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of mixer valve shall be as given in SSR or in relevant IS.

Supply and fixing in repair mixer valve 15mm bore, brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for WHB or fixed to wall, screwed down for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of mixer valve shall be as given in SSR or in relevant IS.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and fixing ball valve and gate valve, complete all as specified and as directed by Engineer-in-charge. (Note :- Float valve and gate valve shall be measured & paid separately as Supply only under appropriate item of BOQ.)

Supply only ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 25mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm// 450mmX 300mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade) 10 mm thick square or rectangular area of each tile not exceeding 0.36 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade) 10 mm thick square or rectangular area of each tile not exceeding 0.36 sqm, as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (screed) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour 18-20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour for counter sunk wash basin, plateform/cooking plateform or as directed, including screed bed 15mm thick in cement mortar (1:4) (grey cement slurry) including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing stainless steel sink made out of 1.00mm thick sheet, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar to dwarf wall or fixing with cast iron cantilever brackets and connecting union to waste pipe; overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-Charge.

Supply & fixing single lever sink mixer with swinging spout on upper side (wall mounted model) with connecting legs & wall flange complete all as specified and directed by Engineer-in-Charge. Make :- Cat Part FLR-5165 of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply & fixing Continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flap when open 30mm complete all as specified and as directed by Engineer-in-charge .

Supply & fixing Drawer pulls, 3 screw plate with fixed dished pull; 80 mm to 100mm long complete all as specified and directed by Engineer-in-Charge.

Material and labour 19-20mm thick PVC board (for cupboard and kitchen cabinets) one side decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

Supply & fixing stainless steel modular kitchen basket accessories cabinets multipurpose utensils drawer basket wred of different sizes, complete all as specified and as directed by Engineer-in-charge .

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old polished wooden surfaces of any description not otherwise described over 10cm width or girth & applying two coats of french polishing to achieve glossing finish including a coat of wood filler complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted (plastered/unplastered/concrete) surfaces of any description over 10cm girth or width, not otherwise described of walls/pillars/cornices by brooming down or steel patti as required etc. and after preparing the surfaces applying two coats of plastic emulsion paint (finishing smooth and glossy upto entire satisfaction of Engineer-in-Charge) as per approved tint/colour with using paint brush/roller, complete as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing water proofing treatment from roof and providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing membrane comprising of the following for non approachable roofs (i) Cleaning and sweeping and washing down with water to remove all dust etc. from plastered roof surfaces/walls and filling of crack with sealing compound etc. (ii) Bituminous based primer conforming to IS:3384-1965@ 0.3 Kg per Sqm (iii) One layer of super thermo APP modified water proofing membrane with non polyester reinforcement 3mm thick having minimum weight @ 3.5 Kg/Sqm, laid with gas torch and pasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surface after cutting necessary grooves and making good with PCC gola 1:2:4, type B1 etc. adhere to bitumen all as per manufactures instructions. (iv) Applying two coat of aluminium paint @ 0.20 Kg/Sqm per coat over bitumen layer as per manufacturer instruction. (Application including sides lap, over laps shall be provided not less than 10 cm and joint sealed with torch as per manufacturer's instructions/specifications 15mm thick cement plaster in 1:4 (v) Taking down of GI pipe and refixing in the same position and as per particular specifications, complete as specified and as directed by Engineer-in-Charge.

Supply and fixed in repair 8 to 10mm thick toughfened glass of any design (frosted) high quality bathroom wall partitions and panel paired with metal framing channels or clamps, fixed to floor and walls/sliding by means of chromium plated/screws, complete as specified and as directed by Engineer-in-Charge.

Excavation in post holes in soft/loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by Engineer-in-Charge.

Material and labour for PCC (1:3:6), type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, bed block, for embedded fencing posts & similar work etc including form work complete all as specified and as directed by Engineer-in-charge.

Material and labour for mild steel work tubular poles/post including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to latest relevant IS grade St-240 complete all as specified & directed by Engineer-in- charge.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Material and labour for MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc. complete all as specified & directed by Engineer-in- charge.

Dismantling of AC (corrugated, semi corrugated etc) sheet in roof cover, complete all as specified & directed by Engineer-in- charge.

Dismantling timber scantling (unframed work) 40 Sqcm and over in section in any position including taking out iron scrap nut and bolts etc. to replace decayed portion of truss, complete all as specified & directed by Engineer-in- charge.

SCHEDULE 'A' ELECTRIFICATION WORKS

Taking down carefully/aluminium point wiring (light, fan, socket or power point ) complete including fitting such as hylem sheet switches, ceiling rose, pendent holder sockets, regulator including concealed conduit and sunken boxes etc and making good distrubed surfaces of wall and floors etc to match with the existing all as specified and directed by Engineer-in-charge.

Material and labour for concealed point wiring complete modular type with 1.5 sqmm (nominal cross section area ) FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked ) drawn through and including PVC rigid conduit 20mm dia( heavy duty) with all fittings and all accessories i.e pipe bend pipe hook, elbow, junction box, pressed steel powder coated sunken box of suitable for mounting modular switches and socket, fan regulator, for light/fan point controlled by one switch, top cover fixed with brass screws & cup washers including provn of 1.5 sqmm FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc including cutting chases in wall and making good distrubed surface of wall/ceiling/floors etc by using CM (1:3 ) to matching with existing surface complete all as specified and as directed by Engineer-in-charge. Make of cable and conduit :- Havellls/Dcab/Finolex/Anchor

All as per item No 100 here in before but for socket outlet 5 pin 5 Amp on same board complete all as specified and directed.

All as per item No 100 here in before but for socket outlet 5 pin 5 Amp on independent board but not below the switch board complete all as specified and directed.

All as per item No 100 here in before but for socket outlet 6 pin, 5/15 Amp multi purpose, 2 in 1 on independent board with 2.5 Sqmm cable & including 2.5 sqmm single core multi stranded FRLSH copper earth wire to common earth complete all as specified and directed.

All as per item No 100 here in before but one light point controlled by two two way switch, complete all as specified and directed.

All as per item No 100 here in beforebut for one call bell control point wiring, complete all as specified and directed.

Taking down carefully unserviceable copper / aluminum point wiring from existing conduit pipe (light, fan, socket,but not removed conduit pipes) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

Material and labour for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in existing PVC concealed conduit and including modular metal flush box & modular cover plate with frame suitable matching colour of required module for mounting or housing for one fan / exhaust fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly etc including cutting chases in wall and making good distrubed surface of wall / ceiling / floors etc by using CM (1:3 ) to matching with existing surface complete all as specified and as directed by Engineer-in-charge. Make of cable and conduit :- Havellls/Dcab/Finolex/Anchor

All as per item No 107 here in before but for socket outlet 5 pin 5 Amp on same board complete all as specified and directed.

All as per item No 107 here in before but for socket outlet 5 pin 5 Amp on independent board but not below the switch board complete all as specified and directed.

All as per item No 107 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc. complete all as specified and directed.

All As per item No 107 in before but for one light point controlled by Two Two way switch all as specified and directed.

Supply and fixing Modular 6 Amps Switch 250 volts AC one way ISI marked. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing Modular 6 Amps Socket 2/3 pin combined 2 module 250 volts AC ISI marked. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing Modular Switch 16 Amps 1 module 250 volts AC ISI marked. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing Modular Socket 6/16 Amps 2 in one 5 pin universal type 250 volts ISI marked. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing Modular 6 Amps, 1 module, Switch 250 volts, two way ISI marked with suitable frame and covers. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing modular bell push 6 Amp complete all as specified and as directed by Engineer-in-charge.

Supply and fixing ceiling rose 3 plate flush type 6 Amp 250V AC topline series with polycarbonate 65 X 50 mm two to three terminal complete all as specified.

Supply and fixing Batten holder 2 Amp 250V AC with skrit ISI marked top line series , polycarbonate cased body of brass with back plate suitable for batten fittings complete including 9w LED bulb all as specified. Make of holder : Anchor/Havells/Legrand/Indoasian/SSK and Make of LED bulb :- Crompton/Philips/Bajaj/Polycab/Havells

Supply and fixing Modular Fan regulator Electronic step type (1-4), socket type 230- 240 volt complete all as specified. Make:-Anchor/Havells/Legrand/Indoasian.

Supply and fixing Electric / Electronic Bell, ding dong type 230 Volt AC supply complete all as specified. Make : Anchor/SSK /Havells/Legrand.

Supply and fixing wall mounted Retro LED 20 watt, Batten decorative type, appx 4 feet long, pre wired including LED tube light 20W, 6000K with inbuilt driver complete fitting and all other accessories fitting arrangements including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector including taking down old unserviceable light fittings any type complete all as specified and as directed by Engineer-in-Charge. Make - Cat part No. LT8-20-865-2 of Crompton/Havells/Wipro/Philips

Supply and fixing in replacement recessed LED ceiling tile with wide light window for maximized glare free output suitable for 600x600mm and ceiling cutout 595x595mm modular grid/POP ceiling complete fitting with separate electronic driver and high brightness LEDs 36 W (100 lumens per watt), not less than 5700K including connecting electric connection including taking down old unserviceable light fittings any type complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED mirror light fiting 9/10 watt, 6000K, lineer & compact with decorative grey end caps, polycarbonate body and ribbrd opal diffuser complete fitting with lamp and all other accessories fitting arrangements including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector including taking down old unserviceable light fittings any type complete all as specified and as directed by Engineer-in-Charge. Make - Crompton/Havells/Wipro/Philips

Supply and fixing wall mounted/surface mounted decorative wall light fixture in cylindrical/Doom profile made up of polycarbonate for and including LED 7 Watt lamp, base B22, complete fitting with LED lamp and all other fixing accessories including electric connection connecting with using flexible copper wire twin core including taking down old unserviceable light fittings any type complete all as specified and as directed by Engineer-in-Charge. Make - Crompton/Havells/Wipro/Philips

Supply and fixing Sleek Pressure die cast aluminium housing/body, heat resistant clear glass, LED lens for wide beam, energy saving, IP65/66 protection, not less than 5700K, better optics for uniform distribution street/Roadway luminaire with high power LED 35 watt complete fitting with driver, LED strip and all other accessories etc, suitable for 40/32mm OD entry for direct mounting on pipe bracket, fixing on poles/along wall with and including brackets made out of GI tubing light grade 40mm dia, 2 metre long bent to shape at 120 degree angle at half metre from bottom (as per sample), fixing with MS clamp (02 Nos) and nut bolts, including before fixing applying two coats of aluminium paint on bracket and clamp over a coat of red oxide primer, including making electric connection with using twin core copper cable of suitable size and including taking down old unserviceable light fitting complete all as specified and as directed by Engineer-in-charge. Make - Cat part No LSTS-35-CDL of Crompton/ BRLEP 35W LED WH of Bajaj / ENDURA PEARL SL35W LED757SASYTOPC of Havells / HLSLD-09-35CWL-R of Halonix

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 8 Way 240V, double door, earth bar, copper bus bar 200 Amp and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement (concealed in wall or as directed) factory made DB (made out of CRCA sheet) SPN, 12 Way 240V, double door, earth bar, copper bus bar 200 Amp and neutral link, protection class IP-43 suitable for mounting MCB/Isolator, conforming to IS-8623, BS-5484 dust and vermin proof, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement (concealed in wall or as directed) sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB TPN 4 way 200 Amps 415 V AC with 200 Amp rated bus bar, Double Door,8 modules, dust and vermin proof suitable for incorporation of MCB's and isolators, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.

Supply and fixing (concealed in wall or as directed) sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB TPN 4 way 200 Amps 415 V AC with 200 Amp rated bus bar, Double Door, 8 modules, dust and vermin proof suitable for incorporation of MCB's and isolators, and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge.

Supply and fixing MCB TPN 100 Amps, 10 KA 'C' curve 415 V AC, 50 Hz including necessary attachment incl taking down old unserviceable MCB SPN complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB TPN 63 Amps, 10 KA 'C' curve 415 V AC, 50 Hz including necessary attachment incl taking down old unserviceable MCB SPN complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SPN 63 Amps, 10 KA 'C' curve 230 V AC, 50 Hz including necessary attachment incl taking down old unserviceable MCB SPN complete all as specified and directed by Engineer-in-Charge.

Supply and fixing MCB SP suitable for 230 volts AC supply 6 to 40 Amps, SP rupturing capacity not less than 10KA, C Curve ISI Marked, 1 Module incl taking down old unserviceable MCB SP complete all as specified directed.

Material and labour for concealed sub main wiring with 6 Sqmm single core (Two run) FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit from DB and including one run 6 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor continues as earth wire connected to earth dolly etc. including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 6 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Material and labour for concealed sub main wiring with 4 Sqmm single core (Two run) FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 20mm dia (medium quality ISI marked), on independent circuit from DB and including one run 4 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor continues as earth wire connected to earth dolly etc. including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 4 sqmm copper wire and one run conduit shall be measured as one RM length for payment.

Supply and fixing (concealed in wall or as directed) single pole and neutral sheet metal enclosure (AC Box/Gyeser) with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement (concealed in wall or as directed) single pole and neutral sheet metal enclosure (AC Box/Gyeser) with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240 volts, AC supply complete all as specified and directed by Engineer-in-Charge.

Supply and hanging/fixing in replacement ceiling fan 1200 mm sweep in white/off white colour, 50watt, copper winding, 3 Blade, single phase, 230 volts 50 Hz double ball bearing, energy saver/energy-efficient, alongwith hanging rod (length as per site requirement or as directed by Engineer-in-charge), canopy (lower and upper), rubber real, nut bolts, lock pin etc. including making electrical connection with flexible round twin core multi strand copper cable suitable size complete all as specified and as directed by Engineer-in-Charge. Make and cat part :- Entrust 50 of Crompton / Energia of USHA / ES 50 of Havelles / Electra 50 of Bajaj Note :- (i) Srl Number of ceiling fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Ceiling fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account (iii) Old rusted and outdated ceiling fans deposited to MES store.

Supply and fixing exhaust fan 300 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Make - Usha / Bajaj / Khaitan / Orient / Crompton / Polar Note :- (i) Srl Number of exhaust fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Exhaust fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account. (iii) Old rusted and outdated exhaust fan deposited to MES store.

Supply and fixing exhaust fan 450 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Make - Usha / Bajaj / Khaitan / Orient / Crompton / Polar Note:- (i) Srl Number of exhaust fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Exhaust fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account. (iii) Old rusted and outdated exhaust fan deposited to MES store.

Taking down existing Gyesers from site before the work of building tiles/plastering and refix the same after completion of tiles/plastering work including painting of gyesers and fixing arrangements and testing of required for proper functionality & including electric/earth connections and carrying out grouting & complete installations with mounting bolts, nuts including testing after installation complete all as specified and directed by Engineer-in-Charge.

Taking down ceiling fan from existing location and keep safe custody in store and refix the same after completion of false cealing work complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in provn electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed by Engineer-in-Charge.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etctesting of required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete all as specified & directed including taking down old unserviceable water heater and deposit to MES store all as directed.

Removing exhaust fan from existing location and keep in safe custody/store for reuse the same after completion of building plastering works, complete all as specified and directed by Engineer-in-Charge.

Fixing only exhaust fan after alteration of building work, complete all as specified and directed by Engineer-in-Charge.

Supply, Install, Testing and Commissioning in repair and replacement of 'Solar Hot Water System' (Flat Plate Collector) based on indirect transfer of heat of capacity 200 LPD including its connected inlet and outlet pipes as per existing system and taking down old unserviceable solar system, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Hot water pipe duly insulated with glass wool and aluminium cladding 15 mm bore, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6.3mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including earth continuity GI wire 4 mm (upto test point from earth plate i.e. 7.5m min) by means of GI bolts/nuts/washers and including protected by 15mm dia GI light grade protection pipe from earth plate to test point, including making of test point. Earth plate shall be surrounded by packed layer of char coal/coke & salt all around bottom and top with alternative layer. 20mm GI light grade pipe for watering (should be 10cm above GL) and including socket, plug, funnel, wire mesh, RCC cover and (including steel for cover) PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in earthing pit including necessary form work, excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR (Part – I) including taking out/dismantling old unserviceable earthing system complete all as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner.

V K CONTRACTOR

Aman Enterprises

G N CONSTRUCTIONS

M K Enterprises

Easyways Enterprises

N.G BUILDERS

M/s MITTAL CONSTRUCTIONS

KARTIK BUILDERS