SPL REPAIR TO BLDG NO T2 EYE DEPT OF MH DANAPUR PROVN OF 02 X HIGH MAST LAMPS NEAR MT GARRAGE AND OUTSIDE OPD PARKING AREA AT MH DANAPUR AND 01 SERVO CONTROLLED AIR COOLED AUTOMATIC VOLTAGE STABILIZER 3 PHASE OF CAP 30 KVA FOR COMN COMPLEX DANAPUR UN

Amount

Dismantling of floor, walls tiles including bedding but not backing and rubbish off permises all as specified.

M & L for Non skid ceramic colour tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed (1:6) etc complete all as specified and directed.

M&L for Coloured glazed ceramic tiles (450 x 300)x 6 to 7mm thick (digital type) on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or colored cement to match complete including 10 mm thick rendering on fair faces of brick work or concrete surfaces, in cement mortar 1:4 all as specified and directed for shade, pattern and laying of tiles complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick wall in cement mortar (1:6) finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

Supply only water proofing compound (liquid),ISI marked complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in Unframed work complete all as specified and directed.

M&L for cutting holes in brick wall built in cement mortar for inserting holdfast , walls exc half brick n.exc one brick thick and making good dismantled portion in cement mortar 1:3 complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mps as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by E-in-Charge

All as per item No12 above but plain sheet as in ridge fixed with self tapping screws all as specified.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

S&F powder coated Gl frame work for ceiling using Main Tee and cross tee of Size 24mmx32mm having 0.27mm guage and sub cross cross tee of size 24mmx32mm having 0.25mm guage and wall angle of size 19mmx19mm having 0.35mm guage,. The mess size will be of 600mmx600mm including supply and fixing of 6mm thick Gypsum tile of zize 600mmx600mm including fastaner as directed by Engr-in-charge complete all as spd and directed.

M&L PCC 1:4:8 type D-2 (40mm graded stone agg) in fdn, sub base, mass concrete & cinder concrete etc. complete.

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed..

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed

~Ditto~ all as per item Ser No 24.00 above but except bricks complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified

Taking down chowkats or frames exc 1.5 Sqm but n.exc. 4 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

S&F powder coated aluminium door shutter side hung in single or double leaf with frames size 85 x 44 x 1.4 mm thick including 5 mm thick tinted glass in half portion and 9 mm thick prelaminated particle board exterior grade, one side with decorative choice and other side balancing white lamination, standard rubber gasket, powder coated aluminium beadings, disc type handles two Nos for each shutters and one mortice lock and joining cleat etc complete all as specified and directed. Make : Jindal/Hindalco or Equivalent

M & L double action floor spring for aluminium doors hydraulically regulated made up of minimum1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

S&F for powder coated aluminium window three track sliding type with frames including 5mm thick tinted glass, stainless steel wire cloath 0.36 mm nominal dia of wire and average width of aperature 1.40 mm fixed with standard rubber gasket, aluminium beadings and joining cleat for fixing including locking devices complete all as specified. Make : Jindal, Hindalco or Equivalent

S&F anodised aluminium grill for window ventilators (diamond shape of approx size 100 x 100 mm) made out of aluminium channel of size 4x5mm as approved by Engr-in-Charge.

S&F powder coated aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws etc complete all as specified and as directed. Make : Jindal , Hindalco or Equivalent

S&F 4 mm thick figured sheet glass pin head type fixed in aluminium ventiliators with necessary rubber and powder coated aluminium snap beading complete all as specified. Make : Modi Float, Saint Gobin

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified.

Demoliton of cement concrete in ground floor paving n exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate /plinth protection laid in suitable panels finished even and fair all as spd . 6mm Joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand ( all by weight) complete all as specified and directed.

Supply only 38mm wide glass dividing strips, 3mm thick complete all as specified and directed..

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of primer over and including 3 mm thick Birla/ JK wall putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

M&L for preparation of new or untreated steel surface of any description exc. 10 cm. in width or girth and applying two coats of synthetic enamel paints, over a coat of red oxide primer, complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 CM girth all as specified and directred

Taking up or down steel tubing and connections, of 15 mm dia complete all as specified and as directed. .

Supplying and laying of CPVC pipes 16mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Dismantling water tanks and removing to store of capacity exc 500 and n exc 1000 ltrs all as spd.

S&F in repair 500 Ltrs capacity rotational moulded polythene water storage tanks in three layer cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed

S&F in repair 15 mm dia nipple suitable for HDPE water tank (min weight 38 gms) complete all as specified and directed

S&F in repair 20 mm dia nipple suitable for HDPE water tank (min weight 45gms) complete all as specified and directed

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball srewed for iron pipe and fixed (minium weight 15mm-142gms) complete all as specified and directed

S&F in repair Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc complete all as specified and directed .

S&F in repair Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

Supply & fixing in repair vitreous china wash basin, light colour as fitted on MS bracket with painted or flat back size 550x400mm excluding tap, waste, chain etc. Make: Hindware/Parryware (Superfine)/Cera (Ist quality)/Jaquar

S&F PVC (SWR) 75 mm bore floor trap/Nahani with grating including jointing with solvent cement complete all as specified. Make : Finolex/Supreme

S&F pillar tap cast copper alloy fancy type with capastan head chromium plated screwed down high pressure with or without lettered “HOT or “COLD” with long screwed shanks and fly nuts, screwed for iron pipe.

S & F bib tap 15mm chromium plated with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by the Engineer-in-Charge.

S&F 15 mm bore concealed type stop valves, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated, with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F PVC connection 15 mm size with 2 No CP check nut & its washer of length 600 mm complete all as specified and as directed.

S&F CP brass tubular towel rail 20mm dia 600 mm long fixed with CP brass screw and wooden/plastic cleats complete all as specified and as directed.

S&F 100 mm dia grating doom of stainless steel complete all as specified and as directed.

S&F 15 mm bore GI Tubing medium grade with fittings fixed to walls, ceilings or laying in floors in comp all as spd and directed

S&F 20 mm bore GI Tubing medium grade with fittings fixed to walls, ceilings or laying in floors in comp all as spd and directed

S&F powder coated anodised aluminium frame for door window and ventilator with one or more rebates including joining cleats for fixing etc complete all as specified.

S&F glass shelf wall corner size 230 mm with all fittings/brackets complete all as specified and as directed by Engineer-in-Charge. Make : Jaquar/Cera

S & F 3 mm thick frosted glass pin head type and glazing with oil putty in squares exc 0.5 Sqm in each pane etc complete all as spd and directed.

S&F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F Aluminium handles, cast type, anodized 150 mm size comp ISI Marked complete all as specified and directed

S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type and fixing clips of sheet, cast or extruded section or cast aluminium alloy etc all complete all as specified and as directed..

S&F 100 mm size butt hinges extruded aliminium alloy with galvanised MS hinge pin Type B-21 complete all as specified and as directed.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Make : Raj shree or Equivalent

M&L for cutting holes in brick wall built in cement mortar for inserting holdfast , walls exc half brick n.exc one brick thick and making good dismantled portion in cement mortar 1:3 complete all as specified and directed.

M & L for 60 mm thick Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006, M-35 grade as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M&L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidized bitumen based solvent primer @ 0.3 Kg / sqm. (iii) Applying evenly tack coat of industrial bitumen 85 / 25 grade @ 1.2 Kg / sqm. (iv) Laying unrolled over the bitumen coat surfaces polymeric water proofing membrane, hyperplas standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction. (v) Applying a coat of aluminium paint @ 100 gm / sqm over and including a coat of hot air blown grade bitumen of grade 85 / 25 @ 1.2 Kg / sqm duly sanded over polymeric membrane complete. NOTE:- The polymeric water proofing membrane shall be extended upto parapet walls and inserted in walls by cutting groove and making good with cement mortar 1:3 as directed.

M&L for 10 mm thick plaster in cement mortar 1 : 4 as a backing coat for fixing of wall /floor complete all as specified.

M&L for durastone heavy duty coloured vitrified tiles 300x300x9-10 mm thick exterior grade set and jointed with neat cement slurry and painted in coloured or white cement to match complete all as specified.

S&F Steel ventilator with top hung shutter including, hinges, peg stay, lugs (MS hold fast) complete all as spd and directed

S & F of 35 mm thick (Batten thickness) factory made plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood complete all as specified and directed.

S & F steel window with side hung shutters including projecting or box stype hinges with steel handle peg stay and divided into square with glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer with including fixing of hold fast of size 25 x 5 mm flat iron etc complete all as specified and directed.

S & F steel window with side hung shutters including projecting or box stype hinges with steel handle peg stay and divided into square without glazing bars dovetailed or welded, to receive glazing, or gauzing including one coat of primer with including fixing of hold fast of size 25 x 5 mm flat iron etc complete all as specified and directed.

S&F factory made 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed

S&F powder coating aluminum partition wall of aluminum section 100mm x 44mm x 2mm thick frame rectangular section and prelaminated particle board exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination in bottom panel and 5 mm thick frosted/tinted sheet glass in top panel with rubber lining and aluminum beading around length including necessary fixing arrangement for bottom and top member of aluminum frame in floor/PCC/Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre & necessary making good to surface as required at site all as specified and directed by Engineer-in-Charge (Note : Cost of PVC panel or prelaminated board and 5mm thick sheet glass shall deemed included in the unit rate of this item )

S & F of 15 mm bore brass chromium plated Mixer for mixing HOT & COLD water screwed down for iron pipe or for brass ferrule complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M & L for Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M & L dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable and gentally hand ramming and consolidation of thickness of sand 18 cm all as specified and directed by Engr - in - Charge. Note :- Sand thickness shall be measured 18 cm only .

M & L for old size sub class ‘B’ bricks, laid in trenches as cable covers / protection complete all as specified and directed .

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

M & L for horizontal boring mechanically across the existing road without disturbing the road surface for inserting 80/40 mm bore GI pipe all complete all as specified and as directed by EIC. ( Note :- GI pipe will be measured and paid respective item of BOQ').

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables, heavy duty with aluminium conductor of cross sectional area 25 sqmm 3.5 core with all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. (Make: HAVELLS/ POLYCAB/Gloster) (NOTE: Earthwork & Excavation, GI pipe brick protection etc shall be measured and paid separately under relevant items of this schedule of BOQ).

Supply, installation and commissioning of 12.5 Mtrs high mast system with its accessories. Mast shaft shall be in two sections,hot dip galvanised and suitable forwind velocity as per IS 875 and including head frame, steel wire rope 6 mm dia (7/19 construction), trailing cable, double drum winch, Galvanised Lantern carriage drum winch arrangement suitable for 6 (six) luminaires symmetrically and lightning finial. The mast shall have an integral power tool installed inside the base compartment for its operation with siutable size electric motor, foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. The high mast lighting system supplied with the following accessories.Make : Bajaj/Crompton Greaves/Havells/Surya

LED flood light luminaires 200 Watts IP 66 type with lens incl standard fittings pressure die cast aluminium housing with heat reistant toughened front glass housing with epoxy powder coated finsh and , complete with control gear box and all accessories duly prewired.- 06 Nos. Make: Bajaj/ Crompton Greaves/Havells/Surya

Low intensity twin type aviation obstruction lamp of GLS type with super bright red LED 300 Nos per lamp of IP – 65 protection aviation obstruction light complete all as directed. Make – CG / Havells / Bajaj / Surya .

Supply, installation, testing and commissioning, factory made and tested, LT feeder pillar box ,outdoor type , platform mounted. The panel shall be dust and vermin proof, IP65 class protection and made out of 3.15mm thick CRCA MS sheet and 40x40x4mm thick angle iron frame work, powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front opening type, with aprons for cable entry, with double door shutter and locking arrangement including provn of 65mm Godrej (Freedom) stranded lock with 2 keys, internal wiring with PVC insulated, stranded copper conductor FRLS cable, IS-694 marked of adequate size but not less than 10 Sqmm. The following items accommodated with this feeder pillar including 02 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enameled white of size 25 x 20cm with letter figures and conventional skull bones in signal red colour and fixed nuts, bolts and washers etc with voltage and danger indicated in Hindi and English complete all as specified and directed. The scope of work includes the following items accommodate the same panel.

(i) Stag type, 4 way terminal (I/P) 63 Amps – 01 No (PCB 150 ACBC) (ii) MCCB 4 Pole, 415 volts AC grade, 40 Amps 25 KA Icu=100%Ics.(Make: Legrand/L&T/ SIEMENS) - 01 No (iii) Contactor 3 pole 32 Amps – 01 No (Legrand/L&T/SIEMENS) (iv) Toggle switch 6 Amps – 01 No (v) Timer (analogue) with battery backup – 01 No (Legrand/L&T/SIEMENS) (vi) Stage type, 4 way terminal (O/P) 63 Amps-01 No (PCB 150 ACBC) (vii) Over load relay 2/3.5A – 01 No (Legrand/L&T/SIEMENS) (viii) F. contractor 9 A – 01 No (Legrand/L&T/SIEMENS) (ix) R. contractor 9A – 01 No (Legrand/L&T/SIEMENS) (x) Motor terminal 32 Amps – 01 No (Legrand/L&T/HPL) (xi) Push switch terminal (STD) – 01 No (Legrand/L&T/SIEMENS) (xii) Push switch (F/R) (STD) – 01 No (Legrand/L&T/SIEMENS)

Pole drawing and RCC/PCC foundation work for errection of pole shall be carried out as per manufacturers approved drawings.

PCC foundation work for LT control Panel as per manufacturers approved drawings.

Work to be executed by the manufacturer or there authhorized rep and MOU undertaking of the same from the manufacturer be submitted prior to excution of work .

Earthing complete with galvanised steel plate electrodes with 25 X 3mm strip og GI as per manufacturers approved.- 02 Nos.

Material and labour for earthing complete with galvanised steel plate electrodes of size 600x600x6mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 32x 6 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 40 mm bore (Medium grade) for LT panel/FPB complete all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all as specified and directed.

Supply and installation, commissioning of Servo Voltage stabilizer of capacity 30 KVA for automatic operation, Three Phase, 50 Hz., for 'Automatic Controlling / Regulating of Voltage Comprising Auto Transformer, Buck & Boost Transformer (Copper Wound), Servo Motor, Auto Controlled Solid State Control Circuit (suitable for supply from D.G. sets also) and other Fittings & Accessories as under:-voltmeter (0-300 V) to read input/output voltage per phase, Mains/Low/High limit Indicators, Manual Increase/Decrease Push Switch, Auto/Manual mode control switch and output adjustment ,and naturally air cooled, indoor type & designed for input variation between 340 V to 480 V with output voltage stabilized at 415 with accuracy ± 2.5% and speed of correction 8 Volts per second as per IS : 9815 with Additional / Optional features of Electronic control circuit, Low Voltage Cutoff, High Voltage Cutoff, Single Phase Preventor, Time delay,Over Load & Short Circuit including testing on completion complete all as specified and directed by Engineer in charge.

Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

M & L for Point wiring with PVC insulated and PVC unsheathed electric FRLS cable of 1100V single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit on surface will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including 1.6mm thick anodised pressed steel sunken box covered with 3mm thick hylum sheet for mounting switches, sockets, fan regulators etc for fan / light point controlled by one switch complete all as specified and directed.

All as per item no 106 above but one bell point controlled by one bell Push

All as per item no 106 above but one 5 Amps socket out let point controlled by one switch on same board with other switches.

All as per item no 106 above but one 5 Amps socket out let point on independent board controlled by one switch.

All as per item no 106 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

All as per item no 106above but wiring with 4.0 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

Supply and fixing switch piano flush button single pole one way 5 amps, 240 Volts complete all as specified and directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, 240 Volts complete all as specified and directed.

Supply and fixing switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed.

Supply and fixing in socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 240 volts complete all as specified and directed.

Supply and fixing bell push single pole, 6 Amps, 240 Volts, flush type complete all as specified and directed.

Supply and fixing for electronic Fan regulator 450 watt step type complete all as specified and directed.

Supply and fixing Ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

Supply and fixing for batten/angular fittings complete all as specified and directed.

Supply and fix LED Lamp 7/8 watt complete all as specified and directed.

Supply and fixing Bell, AC 240 Volts,single pole complete all as specified and directed.

Supply and fixing double door TPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed .

Supply and fixing double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed .

Supply and fixing with MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing MCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing MCB TPN 50 to 63 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with LED tube rod 18/20 Watt internally pre wired and fixed to wall/ceiling incl fittings accessories connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. Make- Havells/ Bajaj/Philips/ CG.

Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with electronic driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and as directed. Make: Crompton/Bajaj/Havells.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof recessed ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. Make, Havells / Philips / Bajaj / Crompton Greaves

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper wire upto ceiling rose complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Usha.

M&L for Sub main wiring two single core PVC insulated unsheathed cable 1100 volts grade, 4.0 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete.

Taking down fan, ceiling fan and dismantling blades and removing fan and blades to store and after cleaning Refixing of refixing the same with replacement of multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

Supply and fixing of down rod for ceiling fan made out of 15 mm dia MS pipe complete with holes, and MS strip clamp with slotted or threaded upto 1.5 m long all as per site requirement specified and directed by Engg-in-charge.

Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete

M/S SHEO KUMAR SINGH AND SONS

M/s KUMAR ENTERPRISES

MS JAGDAMBA ENTERPRISES

G S CONSTRUCTION

J K CONSTRUCTION

MS JODHI PRASAD SINGH SONS

MS CHAKRAVARTY PRITHIVI RAJ

M/S MODERN CONSTRUCTION

M/S Harsh Traders

M/S NANDA CONSTRUCTION