CA NO GE(H)-16/2024-25 SPECIAL REPAIR TO BLDG NO T-528, T-1394, TL-199 AND TL-200 IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN.

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for in this Schedule complete all as specified

Dismantling boarding, any description, fixed in any position with nails, cover fillets of any description as in false ceiling all as directed.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for in this Schedule all as specified & directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts and including Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc complete all as specified. complete all as specified & directed. Note:- Any gap between Pre-painted galvalume aluminium zinc coating sheet and brick wall, if occures after the fixing of sheet shall be filled by CM 1:3 and wall shall be making good as per existing surface.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F GI powder coated snap grid of size 605 mm x 605 mm frame work for false ceiling with main tee 32x24x1mm thick, cross Tee 26x24x1mm and wall angle 24x24x1mm thick, flange covered with PVC thin includng hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified & directed.

S&F Gypsum board 9-12mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 595mmx595mm and the same shall be placed in snap grid as in false ceiling complete all as specified and directed. Note : The snap grid frame work shall be measured & paid for separately

All as per serial item No. 14 above but for fixing only in snap grid.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Glass pane/wire gauze shall be measured and paid separately.

S&F 3mm thick polycarbonate solid sheet, in square/rectangular size, smooth surface, weather resistant, fine finish, bent and pressed including aluminium glazing clips, rubber beading and clear silicon or glazing with oil putty with putty or fixed with beads complete all as specified and directed

Supply and fixing in repairs Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.specified.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing 4mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, including hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified and directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished flat surfaces of concrete all as specified and directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for preparation of newly plastered surfaces of wall & applying two coats of oil bound distemper of approved shade/tint over a coat of primer on walls over one coat of 1mm thick wall care putty all as specified & as directed.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement including mixed with and including liquid water proofing compound @200 ML per 50 KG by weight of cement complete all as specified and directed.Note:- (WPC shall be measured & paid separately under respective item)

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

Supply only water proofing compound (ISI marked).

Material and labour 50 mm thick PCC (1:3:6) type B2 using 40 mm graded stone aggregate as in plinth protection, surface finished fair and even without using extra cement complete all as specified.

S&F for factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled stainless steel ISI marked complete all as specified.

Supply & fixing aluminium handle 150mm size cast type, anodized complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ ISI marked (IS-2062) all as specified and as directed.

S&F in repairs 32mm bore mild steel powder coated curtain rod with 02 Nos decorative ball type brackets (for each opening) and 02 Nos decorative side stoppers (for each opening) fixed on wall with wooden gutties & screws complete all as specified & as directed

M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 1st quality, 300mm x 450mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for vitrified ceramic tiles premium quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.

M&L for Kota stone slab 20-25mm thick in riser of bricks steps & riser of staircase , skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing with & including backing coat in 10mm thick CM (1:3) to receive Kota Stone complete all as specified and directed (Note : Single piece tiles will be placed on the surface of stair case riser area).

M&L for 20mm thick granite slab approved shade, as in platforms etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing including required cutting to suit the size of platforms including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified & as directed.

M&L for 20mm thick granite slab prepolished of approved shade, fixed in wall as Shelves, partition to urinal with cement & sand mortar 1:3, complete all as specified & as directed. Note : (i) External edges of granite stone shall be rounded by using granding machine / grinder. (ii) Stone shall be cut in desired shape as per site requirement and as directed by Engineer-in-Charge.

M&L for factory made vibrate type chequered cement concrete coloured tiles, glossy finish, 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & as directed.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall.

S&F in repair kitchen sink with drainage board (overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm or nearest higher size) ) made from high grade AISI-304 (18/8) stainless steel of 1mm thickness including 32mm bore brass CP waste coupling, plug, washer, 32mm bore and 600mm long PVC waste pipe including fixing cantilever brackets made of MS angle iron 30x30x3mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning of ends of brackets to errecting stand into wall and making good distrubed portion in CM (1:2) on in PCC (1:2:4) using 20mm graded stone aggregate and connecting union to pipe complete all as specified and directed.

S&F in repairs Brass 15mm bore, CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, including plastic seat cover, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and including S&F chrom plated water jet spray with 1M long PVC pipe . and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified

S&F in repairs vitreous china half stall urinal, 580mmx380mmx350mm (minimum), white with CP brass grating and union for discharge pipe includng providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plugs with and including 60mm long brass screws complete with PVC flush pipe complete all as specified and as directed.

S&F 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed on wall necessary fittings / connection & MS clamps / clip and necessary screwing as required in new or old position complete all as specified and directed

All as per item No 67.00 here-in-above but dia 75mm bore.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F in repairs cast iron floor trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

S&F 15 mm bore steel water GI tube medium grade with all fittings / connections & MS clamps / clips and necessary screwing as required complete and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed

All as per item No 74.00 here-in-above but dia 20mm bore.

Fixing only GI water tubing 15 mm bore, medium grade, with & including supply & fixing all new fittings (ISI marked) / connections & MS clamps / clips and necessary screwing as required complete and fixed with or without concealed to walls, ceilings or laid in floors complete all as specified and directed Notes :- (i) Old serviceable water tubing retrieved from serial item No. 72.00 here-in-before shall be used. (ii) Quoted rate shall be deemed to include cost of new GI fittings (ISI marked). Old fittings shall not be used.

All as per item No 76.00 here-in-above but dia 20mm bore.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 15mm bore.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore

S&F in repairs Bib taps, long shank cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete all as specified and directed.

S&F in repairs 15mm bore Stop valve fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union and fixed complete all as specified and directed

S&F in repairs 15mm bore angle cock, chromium plated, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs, PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repair brass chromium plated overhead shower rose 125mm dia round shape with swivel joints complete all as specified and directed.

S&F in repairs Peg set of 06, steel chromium plated complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.

M&L precast cement concrete (1:2:4 type B0 using 12.5mm graded stone aggregate) louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 including taking down existing jalli all as specified & as directed

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) including shutters with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws including powder coated 'D' type handle of suitable size, tower bolt of suitable size, suitable size hinges heavy grade complete all as specified & as directed. Note :- Mortice lock, Door closer & Glass panes/wire cloth shall be measured & paid seperately under relevant item of BoQ.

S&F 4mm thick ACP (Aluminium composite panel) suitable sheet for aluminium door, window, ventilator etc with one or more rebate including jointing cleats, glazing clips, rubber packing, anodised snap beading, screws etc all as specified and directed.

Supply and fixing brass mortice lock, vertical type, size 100mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified. Make :- Godrej / Harrison / Link

S&F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces complete all as specified.

S&F Door closer aluminium (extruded section body), hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

M&L in repairs for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty & fixed as directed

S&F 5mm thick hollow PVC wall lining, single side prelaminated with flat or fancy patterned on laminated side, PVC sheet inclusive of fixing with screws or with solvent cement required at site on walls including necessary corner angles, filltes etc required at site complete all as specified and directed.

S&F mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete, all as specified & directed.

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed.Note :- Reinforcement shall be measured and paid for separately.

Material and labour for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/RCC drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

S&F Grating stainless steel 100 mm dia with waste hole all as directed.

S&F in repair PVC pipes 50mm dia single socketted in any length as in waste pipe of WHB incl necessary itemslike bend, tee etc incl clamps.

M&L for cutting into existing manholes/Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe.

S&F in repairs vitreous china squatting pan (Orissa pattern) of size 580x440mm white with integral foot rests, with CI 'P' or 'S' trap, and fixing in lime concrete (1 lime, 2 sand and 5Aggreate 150mm thick all around and finished just below level rim of pan to receive the floor finish complete all as specified.

Taking down carefully copper/aluminium point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks, DB, MCB etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 25mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including modular sunk type pressed steel box covered with and including modular press steel with cover plate and frame ’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 109.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 109.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board

All as per item No. 109.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 109.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi stranded on independent board including provn of 2.50 Sqmm unsheathed, multistranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs modular type switch 1 way 6Amp, 230Volts 1 modle complete all as specified and directed

Supply and fixing in repairs modular type switch 1 way 16Amp, 230Volts 2 modle complete all as specified and directed

Supply and fixing in repairs modular type socket outlet 6Amp - 5 pin combined 2 modle 230 volts AC complete all as specified and directed

Supply and fixing in repairs modular type socket outlet 6Amp/16 Amp - 3 pin combined 2 modle 230 volts AC complete all as specified and directed

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F modular type Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed

S&F in replacement LED light fitting 1x40W, regal batten for LED incl ultra bright glass LED tube light Aluminium housing with very high efficiency, singel / double side connection all as specified and directed.

S&F in replacement street light LED light fitting 20 Watt, pressure die cast housing with epoxy powder coating, IP65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 25mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed.

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 40Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 40 to 63 Amps 240 Volts , 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. . Note :-Make of MCB shall be same of that DB.

S&F sheet metal enclosure distribution board SP&N, 12 way, double door, powder coated, protection class IP-43, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

S&F sheet metal enclosure distribution board SP&N, 08 way, double door, powder coated, protection class IP-43, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating copper bus bar, complete all as specified & directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore upto 7.50 metre long GI pipe light grade for earth wire protection fixed with poles/wall with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed including dismantling & taking out old existing unserviceable earthing. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.

Supply and fixing ceiling fans (Copper widing) complete with blades, down rod and accessories, 230V, 1200mm sweep, min air delivery 210 CFM, BEE five star rated with brushless direct current motor (BLDC) with remote complete all as specified and directed.

Supply & fixing and testing exhaust fan of 450mm sweep heavy duty, double ball bearing, 1400 RPM, suitable for SP 230 / 250 volt, 50 Hz AC supply complete with louver shutter including fixing / grouting of frame in wall & cutting opening complete with covers & connecting with & including 3 Nos 1.5 sqmm single core, PVC insulated but unsheathed FRLS 1100 volts grade cable with multi-stranded copper conductor from ceiling rose to fan complete.

S&F in replacement LED lumianire 600mm x 600mm, capacity 35/36 Watt, 220 V AC, recessed type with high efficiency PMMA diffuser soft glase free light complete with driver, holder & LED lamp suitable for roof ceiling including connecting up with driver three core flrxible copper conductor of suitable size complete all as specified and directed.

Supply , laying , jointing, testing and commissioning of size 16 sqmm 2core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, strip armoured heavy duty with multistrand aluminium conductors IS-7098, laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Supply & fixing electric water heater, storage type mild steel body with glass lined coating (Outer body) with titanium armour technology inner tank coating for preventing corrison rusting and heating element upto 2KW cap 25ltr, BEE 3star rated complete with all accessories such as safety vlve, thermostate , NRV, connection piece etc complete & directed.

S&F sheet metal enclosure Single pole and neutral with a two pin and earth plug and socket complete with and including one 20 Amp SPN MCB 'C' curve complete all as specified.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness after laying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Excavation in trenches not exceeding 1.5 m wide and not exc. 1.5 m depth for laying cables, foundation for pole, sewer lines etc and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in incl spreading leveling watering and well ramming in layers n. exc 25cm thick etc complete all as specified and as directed.

Removing excavated material to distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point etc complete all as specified and as directed.

B B BUILDERS

malik constructions

M/S Sulakh Brothers

SHRI HARI BUILDERS

M/S KAVITA CONSTRUCTION

M/S D.N Choudhary

m/s krishna engineers1

Siya constructions