SPL REPAIR TO BLDG NO 402 (SERVANT QTR) AND PROVN OF COVER PARKING SHED OF HQ 24 MTN BDE AT UMROI MIL STN UNDER GE UMROI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish of the premises, complete all as specified & directed

Material and labour for coloured non skid ceramics tiles 7 to 8mm thick (square/ rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors over and including 15mm thick screed bed/bedding layer in CM 1:4 set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor, complete all as specified & directed

Material and labour for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10 mm thick rendering in CM 1:4, complete all as specified & directed

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00 sqm with shutters (without taking off shutters from the frame), complete all as specified & directed

Taking down chowkats or frames n. exc 1.50 sqm with shutters (without taking off shutters from the frame), complete all as specified & directed

Refixing shutter in same opening after repairing complete area exc 1.00 Sqm but not exc 2.00 Sqm complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, complete all as specified and directed.

S&F 100% Soild WPC (Wood Plastic Composite) Double Door Frame 125 mm X 65 mm made of solid WPC density not less than 780 kg/Cum and having good srew holding capacity fixed in position with SS Dash fastener/Hold fast of required length as per specification and deawing including two coat of synthetic enamel paint with priming complete all as specified and directed.

S&F factory made 35 mm thick 100% solid WPC (Wood Polymer Composite) both side laminated flush door shutter of required size of density not less than 650 kg/cum with good screw holding capacity and laminate of 1.5 mm thick and stainless steel butt hinged of 100 mm threaded star headed counter sunk ss srews, complete all as specified and directed.

M&L factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & asgap insert for top rail & bottom rail; but wire gauzed i.e. panel will be of wire gauze in lieu of single side prelam PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S.tubes. The wire gauge shall be stretched to tighten firmly, complete all as specified and directed.

M & L factory made 18 mm thick solid WPC ( Wood Polymer Composite) laminated Board of density not less than 650 kg/cum and laminate of 1.5 mm thick of approved colour and fixing steel butt hinges of required size and full body threaded star headed counter sunk ss srews. complete all as specified and directed.

Supply & Fixing sheet glass ordinary quality 4mm thick glazing in square/ rectangle exc 0.50 sqm each pane with oil putty or aluminium beads fixed to steel etc complete, complete all as specified and as directed.

S&F powder coated (minium thickness 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed.

S&F powder coated (minium thickness 50 micron) aluminium door shutters, aluminium section weighing 0.75 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specifiedSupply and fix powder coated aluminium window and ventilator shutters ,sliding type without sash bar , aluminium section weighing 0.55 kg/RM including necessary joining cleats, glazing clips ,rubber packing, anodized alumnium snap beading screws etc complete all as specified and as directed.

Supply and fix aluminium anodised (powder coated minimum thickness of power coating is 50 micron) . Three track sliding window frame with shutters with ( 2 nos glazed and one wire gauzed shutter)including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including aluminium grill of thickness 5mm and opening not exceeding 75mmx75mm etc completee with the following section of frame and shutter (A) Sections for shutter (i) 'H' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick (iii) 'Edge & Bottom' section 41 x 20 x 1.50 mm thick (B) Section for frame (i) Top & Sides 92 X 29.50X 1.50mm thick (ii) Bottom 92 X 29.70 X 1.50mm thick, complete all as specified and directed . Note:- (a) Quoted rate are deemed inclusive of taking down ventilator of any size and any description and making good to match the existing surface as per existing sch of finishes.

S&F 100 mm butt hinges medium weight cold rolled mild steel and fixed, complete all as specified and directed.

S&F 75 mm butt hinges medium weight cold rolled mild steel and fixed, complete all as specified and directed.

S&F aluminium alloy handles size 150mm fabricated type anodised, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 200mm size of extruded section and fixed, complete all as specified and directed.

S & F 300 mm long aliminium alloy ,anodised sliding door bolt with hasp and staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast alunimium alloy and fixed complete all as specified and directed.

S & F 100 mm hasp and staples of alunimium anodised, safty type including bolt to hinges plate and fixed with screws complete complete all as specified and directed.

S & F helical door spring 300mm long incl roller and roller plate complete all as specified and directed.

S&F false ceiling of designer tile ivory painted (high pressure steam cured ) of 4mm thick (as per IS: 14862) of size 595x595mm and any one of the design (cascade or electra) in true horizontal level. Suspended on inter locking metal grid of hot dipped galvanized steel section (galvanized @120gms both side inclusive and black painted groove on all T webs)consisting of main T runner with suitably spaced joints to get required length and 15x32mm made of 0.3mm thick sheet spaced at 1200mm c/c and cross T of size 15x32mm made of 0.3mm sheet 1200mm long spaecd between main T at 600mm c/c to form a grid of 1200x600mm and secondary cross T of length 600mm and size 15x32mm made of 0.3mm thick sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.Main T runners to be suspended from trusses/ceilings using suitable suspension arrangement as per manufacturers instructions/literature. GI adjustable wire of 4mm dia with galvanized butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all T section of 4mm dia GI wire shall be pre-painted with with polyster paint and black painted groove at centre of size 4mm depth and 4.5mm width, including taking down old false ceiling board of any description alongwith rails and connecting items, complete all as specified and directed.

S&F in repair decorative type tubular 20mm e curtain rod chromium plated, complete all as specified and directed.

S&F in decorative brackets for curtain rod in any size complete all as, complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, complete all as specified and directed.

Ditto all as per item No 26 above but 20mm bore

Ditto all as per item No 26 above but 25mm bore

S&F tubes, 15mm bore 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 and fittings as in walls, ceiling, floor etc, complete all as specified and directed.

. - ditto - all as per item No.30 above here-in-before but 25mm bore, complete all as specified and directed.

S&F 1000 ltrs antimicrobial triple layer white coloured rotaional moulded polythylene water storage tank (Cylindrical vertical with closed top) noised and fixed in position complete all as specified and as directed.

S&F in repair kitchen sink of size made out of 1mm thick sheet of overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm plug washer brackets, connecting union, 40 mm dia waste pipe etc, incl waste pipe and 40mm waste coupling complete all as specified and directed.

S&F in repair PVC valve less syphonic action flushing cistern type 9 to 10 ltrs capacity with inlet, ball valve, float and handle including bracket, white colour of approved make, complete all as specified and directed.

S&F vitreous china white wash down water closet (pedestal pattern) including PVC seat cover and connection to drain or out going pipe and to flushing pipe anit-syphonage pipe etc, and including health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long fexible tube and ABS wall hook including making connections and fixed in connection complete all as specified.

S&F in repair wash hand basin, white flat back of size 550 x 400mm excluding piller taps but including waste cupling, waste pipe and bracket etc complete all as specified and directed.

Dismantling AC/CGI/PPGI corrugated or semi corrugated sheets in complete all as specified and directed.

Fixing only plain or corrugated steel sheet of any guage or thickness as obtained from dismantling item and shall be fixed with 'L' or 'J' type hooks or cranked hook bolts as in roof all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating PPGL based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eave board, fixed with self tapping screws, complete all as specified and directed.

Supply & Fix Square color coated UPVC gutter/runner drop for rain water drain in bldgs of size not exceeding 150 mm with firmly attached downpout of suitable size discharging storm water into PVC SWR pipe of 110 mm dia and similar works etc complete all as specified and directed. Note: the rate shall be inclusive of downpouts, drop outlet, Elbow, End cap, Straight connecter, brackets, downspout couple, splash block, out site corner, clamps as required at site as per standared Engineering practice.

Material & Labour for preparation of old surface applying two coats of synthetic enamel paint on old steel surfaces of any description over 10 cm wide or girth incl preparation of surface etc., complete all as specified and as directed.

Demolition of RCC with concrete cutter machine of any description and in any position not otherwise specifically provided for including taking out and seperating old reinforcement and removal of debries to a distance not exc 50m as directed by Engineer in charge and making site clean complete all as specified and directed.

Material and labour for taking down of existing roof treatment from roof and terrace, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following steps and specifications:- a) Applying crack seal compound of same manufacture of waterproof to fill all cracks of observed on the roof. b) Applying cement slurry over concrete surfaces @3kg/sqm. c) Rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound as per manufactures’ instruction(not less than 3% by weight of cement) on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). d) Applying evenly one coat of primer coating (diluted with water in the ratio specified by Manufacturers) (min @100-110Sq Ft per liter (diluted quantity)) on the cleaned plastered surfaces. The surface shall be left for air dry for minimum period of 2-3 Hrs. e) Applying evenly one coat of elastomeric water proof coat in one direction (as specified by Manufacturers)(min@ 0.9-1.0 sqm per ltrs) and allow to air dry for 4-6 hrs before applying second coat in other direction perpendicular to the first one (as specified by Manufacturers) (min @0.9-1.0 sqm per ltrs. The total thickness of two coats shall be 0.5 to 0.6 mm. f) The whole system shall be left for air cure for min Seven days (without any movement). Make : - Dr Fixit Newcoat Ezee or Berger Home Shield PU RoofKoat or Asian Paints Smartcare Damp Proof or as equivalent approved by GE. Note : - (i) The waterproofing shall be carried out in the last stage of execution to avoid any damages during the execution. (ii) Payment against this item shall not be allowed till completion of all the stages of work for any slab. (iii) The work shall be executed through Authorized well-trained applicators as per manufacturer’s instructions after obtaining written approval from the GE

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc, complete all as specified and directed.

Demolition of brick work built in CM including all quoins, arches, pillars etc, complete all as specified and directed.

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6, complete all as specified and directed.

M&L for Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, chajja, fins, facia etc upto 3 storey height mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed Note :- (a) Supply only water proofing compound shall be measured and paid separately under relevant items. (b) Cost of scafolding upto 3 storied height of building for rendering is deemed included quoted rate of this item. (c) Rendering will be done in two layers. 1st layer will be 10 mm thick and 2nd layer will be 5 mm thick, mixed with WPC.

Supply only integral WPC (Integral waterproofing and application) as per manufacture instruction, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) internal surfaces on other than fair faces of brick work or concrete surfaces, complete all as specified and directed.

Material and labour for 5 mm thick rendering in cement mortar (1:3) on fair faces of exposed/non exposed concrete surfaces such as soffits of slabs, chajja, fasia and simillar work in area of patches n exc 1.0 sqm & including mixing of integral water proofing compound as per manufacture instruction, complete all as specified and directed. Note :- (a) Supply only water proofing compound shall be measured and paid separately under relevant items.

M&L for preparing surfaces of newly plastered surfaces on walls and applying two coat of distemper oil emulsion including 1.5mm thick internal wall putty with alkali resistant primer, complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over over new complete all as specified and as directed.

Material and labour for three coats of white wash on newly plastered surfaces of ceiling including preparation of new plastered surafaces, complete all as specified and directed Engr-in-Charge.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over over old surfaces including complete removal of existing treatment and Washing, rubbing down and stopping of distempered and painted surfaces, complete all as specified and directed Engr-in-Charge.

M&L for complete removal of existing treatment on walls and applying two coats of distemper over a coat of wall care putty of thickness 1.5mm and alkali resistant primer, complete all as specified and as directed.

Material and labour complete removal of existing tretment and applying for three coats of white wash surfaces of ceiling including preparation of surafaces, complete all as specified and directed.

Demolition of RCC chajja and complete/Partial removal of loose/ cracked RCC including cutting of reinforcement from RCC roof projection, chajja, fins, facia etc, complete all as specified and directed. Note:- 1) Quoted rate shall be deemed inclusive of Scaffolding if required up three storey.

Material and labour for RCC (1:1.5:3) type A0 using 12.5 mm graded aggregate) and applying bonding agent as per manufacture instruction as per and making good with the undisturbed portion and in any position finsihed the surface even and smooth without using extra cement including necesary welding/binding of reinforcement if required, complete as directed by Engineer in charge. Note:- (i) Quoted rate shall be deemed inclusive of bondig agent fosroc nitobond EP ,Sika hibond, Pidilite 301 pidicrete URP. (ii) Quoted rate shall be deemed inclusive of Scaffolding if required.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges, complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as specified and directed.

Demolition of stone slabs of any description or thickness, complete all as specified and directed

M&L for Green Marble work 18 to 20mm thick (table rubbed and pre polished) in steps (in single piece), jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble over a screed bed/backing coat of 20 mm thick cement mortar 1:6, complete all as specified and directed.

S&F Stainless steel kitchen rack / plate rack of size 31"x36"x10" , made of stainless steel sheet 0.63 mm thick etc, complete all as specified and as directed.

S&F in repair PVC ball valve 20mm high pressure of PTM with epoxy coated aluminium rod and high density plastic ball serewed for iron pipe, complete all as specified and as directed.

Taking down soil pipe/ rainwater pipes (any size or pattern ) , including all fittings, heads, shoes, bends, swan-necks,etc., including cleaning or refixing (measured overall as fixed along the centre line over fitting and (accessories), complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including scafolding etc, complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including scafolding etc, complete all as specified and as directed.

S&F for 110mm dia pvc bend etc fixed with rubbr ring fixed to wall including scafolding , complete all as specified and as directed.

S&F for 75mm dia pvc bend etc fixed with rubbr ring fixed to wall including scafolding all as specified and directed.

S&F for 110mm dia pvc T etc fixed with rubbr ring fixed to wall including scafolding, complete all as specified and as directed.

S&F for 75mm dia pvc T etc fixed with rubbr ring fixed to wall including scafolding, complete all as specified and as directed.

M&L for Nahani trap with grating for 100mm dia outlet pipe, including making good distrubd area/surfaces with cement concrete/cement mortar 1:2:4 etc including taking down old unserviceable Nahani/Floor trap, complete all as specified and as directed.

M&L for floor trap with grating for 100mm dia outlet pipe, including making good distrubd area/surfaces with cement concrete/cement mortar 1:2:4 etc including taking down old unserviceable Nahani/Floor trap, complete all as specified and as directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup (concealed type) cast copper alloy, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&F in repairs of stop valve 15 mm dia CP fancy type, with long shank and cup cast copper alloy, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repairs 15 mm dia fancy type pillar tap cast copper alloy, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe & fixed, complete all as specified and as directed.

S&F in repairs Shower Rose 125mm size Chromium plated with swivel joints, any size, including fixing to steel pipe or union, complete all as specified and as directed.

S & F in repairs Brass chromium plated tubelar towel rail, 20mm dia, D type, 60,cm long between flanges, complete all as specified and as directed.

Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or reinforced concrete) set in CM, complete all as specified and directed.

S&F PVC (SWR) pipe 150 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors cement, complete all as specified and directed

M&L for concrete bed to drain pipes including pakcing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:3:6 type C2 for 150 mm bore of pipe, complete all as specified and directed.

Demolition of precast concrete block walling set in cement morter, complete all as specified and directed.

Material and labour for brickwork with AAC block (autoclave aerated concrete) brick work in CM 1:6, Straight or curved on plan exc 6 m mean radius, complete all as specified and directed.

M&L for cement concrete, 1:4:8, type D2, (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, complete all as specified and as directed

M&L for PCC 1:2:4 type B0 (using 12.50 mm graded stone aggregate) as in coping, benching/haunching, slightly rounded or chamfred angle and throating etc, complete all as specified and directed.

Demolition of cement concrete of any dsecription and in any position not otherwise specifically provided for etc, complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 Type B-1 ( using 20 mm graded crushed stone aggregate) as in sub base of floor, complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20 mm graded aggregate as in plinth protection finished fair and even with using extra cement, complete all as specified and as directed.

M&L for cement concrete type C1 1:3:6 (20mm graded stone aggregate), in surface channels and drains, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc, complete all as specified and as directed.

Supply & Fix second class hard wood, clean sawn, weather boarding (Eaves Board of second class hard wood) plain 25mm thick and 225mm wide (V jointed to give 20mm laps) and including two coat of synthetic enamel paint with one coat of pink primer and including replace old decayed boarding & including cutting out old pieces and removing dismantling boarding, complete all as specified and directed. Note:- (a) Qouted rate deemed to be inclusive of scafolding work upto 14.00 meter ht.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and as directed.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for painting to steel Surfaces of any description, over 10cm in width or girth with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

M&L for 40 mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in floor/hardstanding, complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed.

Material and labour for point wiring for One light/fan point controlled by one,one way switch, with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and including PVC casing and caping including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of suitable sizes with plastic laminated white/coloured top sheet cover 3 mm thick complete all as specified and directed as below :- Note:-Rate for Cutting, chieseling and making good the existing surface for complete concealed wiring is deemed to be included in quoted rate, complete all as specified & directed.

All as per Sr. Item No. 102 herein-above but for One 3/5 Pin 5 Amps socket out let point on independent board.

All as per item No 102 here-in-before but using 2.5 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board.

Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, one way, complete all as specified & directed

Supply and fixing switch socket out let combination multipurpose 5 pin, 5/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered), complete all as specified & directed

Supply and fixing switch socket out let combination multipurpose 5 pin, 5 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) in independent board, complete all as specified & directed

Supply and fixing ceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals, complete all as specified & directed

Supply and fixing ceiling ceiling fan regulator electronic, deluxe, rotary, step type, 120/280 V, complete all as specified & directed

Supply and fix of MCB SPN DB 4 way double door,IP 43 protection,Glazed door, isolated neutral bar, insulated bus bar assembly, mechanical strength of IK09, complete all as specified and directed

Supply and fix of TPN DB 4 way, double door, complete all as specified and directed

Supply and fix MCB SPN 40Amp, complete all as specified & directed

Supply and fix MCB TPN 63Amp, complete all as specified & directed

Supply and fix MCB SP 6-32 Amp, complete all as specified & directed

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to earth lead wire 4 mm dia by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (medium grade) for watering, charcoal and salt in alternate layers including necessary execuation and earth works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including, complete all as specified & directed.

Supply and fixing Bulb holder angular PVC/Polycarbonate suitable for batten fittings including LED blub 7 watt, complete all as specified and directed.

Supply and fix LED fitting 1x18 watts including Tube rod, 230 Volts, bipin holders connector block etc.complete with all accessories internally pre-wired and including provision of PVC round block 7.5cm dia and 2 cm in depth (2 Nos) for mounting the fittings and electrically connecting with three single core 23x0.0076 PVC insulated multistranded copper conductor flexible cable from ceiling rose to light fitting, complete all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 4 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing capping of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring two run of 6 Sqmm cable one run of casing capping and one run of 6 Sqmm earth continuity wire for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run including taking down of old U/S submain wiring, complete all as specified and directed. Note:- Three runs of 4 sqmm cable and one run of PVC conduite shall be measured as one unit.

Supply and fixing of LED securityt light fittings in aluminium PDC housing, toughened glass cover,individual LEDs with secondary optics,covered with IP66 protection with inbuilt surge protection of minimum 5 kV and repair/replacement warranty of minimum 3 years of capacity 25W including 32 mm dia GI tubing light grade bracket over all 1.2 mtr length with cutting as required and bend to shape with flat iron clamp of size 32 mm 2 Nos, suitable size of nut bolts and washers, complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and directed

Schedule of Credit

M/s Jaiswal and Co

Goswami Traders

S. R. TRADING