REPAIR TO FLOOR, ROOF, WALL, CEILING, PLUMBING AND SANITARY FITTING WORKS IN OASIS COMPLEX, HUNTER COMPLEX AND BTF COMPLEX AT TECH AREA AT AF STN NAL

Amount

Demolition of RCC any description and in any position not other wise specially provided for (reinforcement cut as required to faciliate demolition ) complete all as specified and directed.

Material and labour reinforced cement concerete1:2:4, type B-1 (nominal mix) using 20mm greded crushed stone aggregate) as in slabs supported on walls, beams, columns, shelves and like complete all as specified & directed. (Reinforcement shall be measured and paid for separately)

Use and waste of Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified & directed.

Use and waste of Formwork to soffits of suspended slab such as in chajjas; flat rough finished surfaces of concrete complete all as specified & directed.

Use and waste of Formwork to edges of concrete flats, treads, floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

Material and labour mild steel TMT Bars 6 to 8 mm and above cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed) not less that 0.90 mm dia or securing with chips complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving exc.15 cm thickness above ground level and removing the rubbish outside MoD land complete all as specified & directed.

Material and labour 75mm thick PCC 1:3:6 type C-2 ( using 20mm graded aggregate) as in plinth protection laid in alternate bays, surface finished even & smooth without using extra cement including making joints complete all as specified and directed.

Material and labour 75mm thick PCC 1:4:8 type D-2 ( using 40mm graded aggregate) thick as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed.

Material and labour Fine sand filling under floors or in foundations including watering and consolidation for Interlocking paver block and similar works etc complete all as specified and directed.

Material and labour Vibrator finished rubber moulded concrete coloured interlocking paver block of approved shape and size confirming to IS 15658-2006 of 80mm thickness with grey cement and no pigment, M-40 Grade of approved colour and design complete all as specified and directed.

Rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil complete all as specified .

Material and labour for Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed at a level n.exc 1.5m above starting point complete all as specified and directed by Engr-in-charge.

Material and labour for Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store & rubbish off the premises. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Material and labour Glazed ceramic tiles in vertical surface 350x 250x 7 mm / 450X 350X 7mm thick, (Square/rectangular ) dark/printed in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm set & jointed in neat cement slurry and pointed with coloured cement to match, over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 complete all as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and directed.

Material and labour for vitrified light shade ceramic tiles 8 to 9 mm thick polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as directed by Engr-in-Charge.

Ditto all as per description of above ser item No.19 here in before but in skirting and over 10mm cement backing in CM 1:4 complete all as specified and as directed.

Dismantling of stone patti slabs in roofs including demolition of PCC cover of stone slab , suspended floors, chajjas, landings etc, any thickness jointed in any mortar complete all as specified and directed.

Supply and fixing MS Plates, square cut, with riveted, bolted or welded attachment FE-410-W(Gde-E-250) quality A complete all as specified and directed.

Material and labour for MS work in Roof trusses (framed), trussed, purlins, crane gantries, rails, posts and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.including special shaped washer etc. complete and including all necessary drilling or cutting holes in brick/ concrete surfaces and making good, welding work, bolting or reveting etc and similar work conforming to Fe-290 Gde E-165 complete and all as specified and directed.

Material and labour for Pre-painted galvalume aluminum zinc coating GI based corrugated or semi corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement moryar (1:4) including pointing in white cement (1:2) using marble duet with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and including rounding of edges of granite slabs 10 to 20 mm thick by grainding and rubbing and finished smooth, coloured as approved by GE complete all as specified and directed. Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra paid on this.

All as per description of serial Item no.26.00 here in before but as on vertical surfaces and over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Demolition of brick or stone masonry built in cement morter incl all quions, arches, pillar etc. complete all as specified & directed.

Material and labour brick work with sub class 'B' bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified & directed.

All as per description of serial Item no. 29.00 here in before but as in half brick thick wall built in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Material and labour rendering 15mm thick plastering on other than fair faces of brick work or concrete surfaces in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour rendering 10mm thick plastering on concrete surfaces in cm 1:3 as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour rendering 15mm thick plastering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper (white or tinted) over a coat of approved primer complete all as specified and directed.

Preparing new plastered surfaces of wall and applying two coats of oil bound distemper emulsion over one coat of primer complete all as specified and directed.

Preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Preparing new plastered surfaces and applying two coats of acrylic emulsion exterior paint over a coat of primer, tint as approved by GE in camoflauge pattern to match existing surface complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of plastic emulsion paint over a coat of primer, over two coats of birla white putty complete all as specified and directed.

Complete removal of existing treatment including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescence salts, trading oil and grease etc and applying two coats of plastic emulsion paint over a coat of primer, over two coats of birla white putty complete all as specified and directed.

Preparation of old decorated surfaces of ceiling/bottom of chajja and similar suspended work (plastered or un plastered) including cornices, pilaster etc by brooming down with steel wire brushing, scrapping down, smoke soot, moulds, moss and efflorescence salts, trading oil and greasy spots etc and applying one coat of white wash complete all as specified and directed.

Preparation of old decorated surfaces of walls (plastered or un plastered) including cornices, pilaster etc by brooming down with steel wire brushing, scrapping down, smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc including filling the depressions with birla white putty and applying one coat of oil bound distemper complete all as specified and directed.

Preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of tint/shade as approved complete all as specified and directed.

Preparation of old painted steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of tint/shade as approved complete all as specified and directed.

Dismantling of ceiling boards (fibre, PVC, Pulp, insulation etc ) of any description, any thickness including frame / grid, fillets work etc complete all as specified and directed.

Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after necessary repair work such as setting of floor spring, pivot adjusting etc incl necessary fixing of screws etc for proper function of aluminum door of size n exc 1.5 sqm each complete all as specified and directed.

Supply and fixing as in repairs door closer hydraulically regulated cast iron body, designation No 2, universal type, suitable for door shutters of size 701 to 850 mm in width and of weight between 36 to 60 Kg, complete all as specified and directed.

Supply and fixing as in repairs mild steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed.

Supply and fixing as in repairs aluminium grill of size, 85mm x 85mm hexagonal shaped mesh, fixed to aluminium frame work with 'U' clip of size 15mmx12mm & fastners complete all as specified and directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors, windows, ventilators and partitions (Fixedportions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directionsof Engineer-in-Chief

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,rollers & dust proof brush for sliding door / window complete all as per architectural drawings and the directions of Engineer-in-Chief.

Supply and fixing double action floor door spring hydraulically regulated made up minimum 1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified.

Supply and fixing top pivot of casting body suitable for aluminum door complete all as specified and as directed.

Supply and fixing 170 to 200 mm size extruded aluminium alloy handels fabricated fancy type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads, clips etc complete all as specified and directed.

Supply and fixing 3 mm thick high quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed.

Supply and fixing steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Supply & fixing 1.25 mm thick Pressed Steel door frames size 105x60mm for doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 125x60mm for double doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified.

Supply & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used insted of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS frame welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified in SSR Part -II.

Supply Only 18 mm thick Rajshree Celuka Ply of plain colour Sheet for kitchen cabinets sides , top , bottoms and shelves inside the cabinet.

Supply Only 18 mm thick Rajshree Celuka Ply of one side prelam/Rigidlam and other side plain white colour to make kitchen cabinet shutters / drawer

Supply Only Auto closes hinges for kitchen cabinet shutters.

Supply Only Ball bearing runners 45 mm telescopic Channel ( 20 inch) Full Extention Load capacity 50 kgs.

Supply Only Stainless Steel handles 100 mm size for Kitchen Cabinet Shutters.

Material and labour for providing cupboard shutter in required size at site made out of 18 mm thick PVC colour sheet and provision of shutters one side decorative pre laminated PVC sheet and all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where required. All the edges shall be covered with 2 mm thk edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engr-in-charge.

Supply and fixing factory made 30mm thick flush shutters, solid core construction with particle board core and plywood face panels, both faces is covered with decorative face veneer with lipping for the provision of suitable blocks for taking mortice locks, latches, or other fittings complete all as specified and directed.

Supply and fixing 30 mm thick 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm BWP commercial ply with commercial veneering on both faces; supplied and fitted to chowkats complete all as specified and directed.

Preparation of new wooden surfaces of any description not other described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of new steel surfaces of any description not other described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re-fixing in same opeing after re-securing or easening and adjusting including repair complete all as specified.

Supply and fixing Aluminium butt hinges medium weight, cold rolled, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150 mm size extruded aluminium aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed.

Supply and fixing in repairs in stainless steel wirecloths 0.45 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed.

Supply and fixing In repair 140mm long floor door stoper of aluminium alloy body and toungue, anodised wirh hard drawn steel spring,fixed to door shutter fixed with stainless steel screws complete all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads and S&F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes complete all as specified and directed.

Supply and fix in repairs heavy duty Stainless steel (Grade 305) curtain rods 25mm dia complete all as specified and as directed.

Supply and fix in repairs Stainless steel (Grade 305) brackets with finnals (open ends) suitable for curtain rods of 25mm dia complete all as specified and as directed.

Supply and fix in repairs Stainless steel (Grade 305) brackets (Dead ends) suitable for curtain rods of 25mm dia complete all as specified and as directed.

Taking up or down 15 mm dia steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed..

Taking up or down 20 mm dia steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed..

Supply and fixing 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Supply and fixing 20mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Dismantling water tanks any type of capacity Exc 500 but n.exc 1000 liters complete all as specified and directed.

Supply and fixing 1000 liter capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as secified and directed.

Supply and fixing in repair long body stop valve 15mm bore fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

Supply and fixing in repair 15mm long body bib taps long shank cast copper alloy with crutch or butterfly hadle secrwed for iron piper or for brass ferrule complete all as specified and directed.

Supply and fixing in repair Pillar taps long body fancy type with capasten head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

Supply and fixing in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats complete all as specified and directed.

Supply and fixing in repairs 100 mm dia Stainless steel grating complete all as specified.

Supply and fixing in repairs 75 mm dia Stainless steel with hole grating complete all as specified.

Supply and fixing in repairs waste down pipe 32/40mm bore for wash basin/sink complete all as specified and directed.

Supply and fixing in repair vitreous china wash down water closet pan pedestal pattern ( type white including PVC seat cover, connection to waste pipe and flushing pipe complete all as specified and directed.

Supply and fixing in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, L-Bend complete all as specified and directed

Supply and fixing in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed

Supply and fixing Vitreous China urinals, bowl type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe. fixed in repairs complete all as specified and directed.

Supply and fixing as in repair sinks with drain board made of stainless steel sink of 1mm thick sheet for kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to draft wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed as in repairs complete all as specified.

Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed

Supply and fixing110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

Supply and fixing 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

Supply and fixing PVC (SWR) bends of 110 mm bore complete all as specified and directed

Supply and fixing PVC (SWR) bends of 75 mm bore complete all as specified and directed

Supply and fixing in repair 75mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Taking down U/S existing sub main wiring copper/ aluminium conductor including conduit/ casing and capping etc.

Material and labour for point wiring using 1.1 kV grade single core FR-LSH flexible cable, conforming to IS 694: 2010, having multi-drawn thin strands of electrolytic copper conductors and insulation for phase, neutral, and earth continuity conductor connecting to earth dolly, colour-coded as per IS 11353: 1985, drawn in medium grade UPVC surface / recessed conduits, conforming to IS 9537 (Part- 3): 1983, of size not less than 20 mm NB, including cutting chases, factory made not less than 1.2 mm thick sunken, modular flush sheet galvanized metal enclosure haing zinc coating not less than 120 GSM, , conforming to IS 14772: 2000, having top, bottom, side and back-wall knockouts for conduit entry from any direction, suitable modular cover-plates and making good of disturbed surfaces of wall / ceiling / floor, etc. complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

One fan point / Light Point controlled by one switch, with cables 1.5 mm² size

One 6 A socket outlet on same Board, with cables 1.5 mm² size

One 6 A socket outlet on ind Board, with cables 1.5 mm² size

One 16 A socket outlet, independent, with cables 2.5 mm² size

Supply and fixing modular type 2/3 pin combined shuttered type 16 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 2/3 pin combined shuttered type 6 A socket, conforming to IS 1293: 2005 complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 6 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge.

Supply and fixing modular type 16 A 1-way SP switch conforming to IS 3854: 2012 with finger-proof terminal complete all as specified in IS 732: 2019 and directed by the engineer-in-charge

Material and labour for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed.

Supply and fixing sheet metal enclosure 20 Amps single pole and natural with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 20 Amp fixed properly in concealed position including making good disturbed surface all as directed by Engineer-in-charge.

Supply and fixing exhaust fan 300 mm dia including louvers AC single phase 240 volts of size 300 mm sweep(metal body) and not less than 900 RPM including flexible wire 3 core 1.5 Sqmm from ventilator fan to ceiling rose all as specified and as directed.

Material and labour for sub-main wiring with two single core 4 sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of masonary including 20 mm dia non-metallic PVC conduit fixed in wall including 4 sqmm copper earth continuity wire, accessories and connecting to earth dolly complete, (for AC points). Note : 2 Run of 4 Sqmm, 1 Run of PVC conduit & 1 Run of 4 Sqmm earth cable shall be measured as single unit length

Supply and fixing modular cover plate with frame, of following modules complete all as specified and directed. Note- Modular switches, sockets & Cover plates with frame shall be of same make & model.

8 Module

6 Module

3 Module

2 Module

Supply and fixing rectangular modular flush mounted Sunken block of following modules suitable for mounting, Modular switches & sockets, complete all as specified and directed.

8 Module

6 Module

3 Module

2 Module

Supply and fixing in repair stepped type electronic fan regulator, 2 Module white polycarbonate body, flush type, 230 V, including connecting complete all as specified and directed.

Suply and fixing as in repairs recesse mounted 36w LED ceiling light fitting provided with best in class aesthetics premium white poeder coated frame blends seamlessy with ceiling layout suitable for 600X600 MM modular ceiling grid and also can be suspended with provided kit.

N.K. CONSTRUCTION COMPANY (BID ID -3120170)

SHREE GURU NANAK CONSTRUCTION COMPANY (BID ID -3109609)

Durga Construction Company (BID ID -3124261)

m/s gaurav enterprises (BID ID -3111708)