SPECIAL REPAIRS TO SWIMMING POOL AT MISC AND S UNDER GE (SOUTH) AHMEDNAGAR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete complete all as specified and directed. .

Demolition of cement concrete (un-reinforced) in ground floors & pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

Taking down chowkhats or frame with shutter without taking off shutter from the frame n.exc 1.50 sqm & removing from site.

S&F for Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube,suppling and fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Fatory made solid panel PVC door shutter, 30mm thick (stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded feathered edges plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struk inside with solvent cement for stiles and plain colour feathered edges PVC sheet for top rail,lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles & rails with suitable for feathered edges PVC sheet, and jointed together with solvent cement, suppling and fixing in the frame at site as per specification & drawing complete all as specified and as directed

S & F for Aluminium handles, cast type, anodised, Size of handle in 150 mm,etc complete all as specified and directed.

S&F Aluminium anodised,barrel tower bolts of extruded section and fixed, length of bolt in 150 mm etc complete all as specified and directed.

S&F for SS Butt hinges, with SS hinge pin, bright polished and fixed, of size 100mm long etc complete all as specified and directed.

S & F for Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 250 mm etc complete all as spd and directed.

Demolition of brick/ stone masonry built in cement or lime mortar all as specified and as directed.

M&L for filling of Crack with Fiber glass reinforced crack filling compound all as specified and as directed. Note:Cracks shall be sealed at a depth of 2 times the crack width, surface overband shall be limited to a maximum width of 3 inches with the maximum thickness of 1/8th inch. when repairing cracks.

M&L for brick work with old size fly ash bricks, class designation 75(Kgf/cm2) straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick masonary surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over and including primer complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick masonry surfaces or concrete surface, finished even and smooth with sagol finish without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered wall surfaces, and applying minimum 1mm thick wall care putty over prepared wall surface including sanding of the putty surface after drying to achieve even and smooth finish and applying two coat of OBD over and including a coat of primer complete all as specified and directed.

S&F GI wire netting 0.90 mm dia and 12mm mesh, in walls, celling, beams etc including all laps cutting and waste, including making V groove in crack portion and filled with cement mortar 1:2 etc complete. all as specified and as directed.

Dismantling asbestos cement (corrugated, Semi-corrugated etc.) sheets in roof coverings above 10 meter height from ground level complete all as specified and as directed. .

Excavation over areas n exc 1.5m in depth in soft soil for foundation etc and getting out complete all as specified and directed.

M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core of gauge exc. 63 mm but n. exc. 100 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D2 (using 40mm graded aggregates) as in foundation, filling and mass concrete etc complete all as specified and directed .

M & L for Mild steel bars 10mm dia TMT bar and over, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in floors complete all as specified.

M&L for reinforced cement concrete M25 using 20mm graded stone aggregate as in foundation including raft, footing foundation beams, plinth beams , bases for column ,basement of slab, etc mass concrete all as specified and as directed.

M&L for 25 mm thick plain cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in floor or basement of slab, etc mass concrete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coated galvanised Iron based corrugated steel sheeting 0.5 mm thick, with side lap and end lap of any colour having tensile strength 550 MPA ridges, hips, valley gutters, drip and straight flashing or in roof covering fixed with self taping screws (length & girth as fixed) at any height complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coated galvanised Iron based Plain steel sheeting 0.5 mm thick, with side lap and end lap of any colour having tensile strength 550 MPA ridges, hips, valley gutters, drip and straight flashing or in roof covering/cladding fixed with self taping screws (length & girth as fixed) at any height complete all as specified and directed.

S&F joist, channel,angle, pipe,or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengthsbie. Within 20mm of length indicated) of Fe-290(Gde E-165)

S&F Rolled section as in main and cross beam , hip and jack rafters; purlin where connected to running rails fixed with angle cleats or other connecting plates of Fe-290 (Gde E-165)

M&L for extra over rendering or plastering for work in isolated width or in widths not forming part of general plastering such as in bands , sunk panels, cornices, skirtings, drip moulds and simmilar work n exc 15 cm in width and girth

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc. (ii) Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying as in roof slab with mixing of WPC and surface finished fair and smooth without using extra cement. (Note: WPC shall be measured and paid under separate items) (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.70kg /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm (minimum) reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of bituminous aluminum paint over the APP modified membrance @ 0.11Kg/sqm each.

Supply only water proofing compound complete, ISI mark all as specified and as directed.

M&L for glazed coloured ceramic tiles of size 450 x 300 x 7mm thick in vertical surface of walls,color/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles over & including 10mm thick rendering in CM 1:3 on other then fair faces of brick work wall finished rough to fix tiles complete all as specified & directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, color/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

M&L for factory made vitrified paver tiles , 300mm x 300mm x 10mm thick , as approved by GE as in floors , laid over and including screed bed 15mm thick in cement mortar 1:4 set, jointed and pointed in neat cement slurry all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like as in RCC plateform incl necessary cuttings for fixing of sanitary oval type WHB and bedded over and including 20mm thick screed bed in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 20-25 mm thick, machine cut cudappah stone slab flooring, laid over and including 20mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

M & L for preparation of old plastered surfaces of ceiling and applying two coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered wall surface and apply two coat of white wash on wall as directed by the Engineer-in-Charge.

M&L for preparation of old decorated plastered surfaces of wall including filling the holes and cracks with white cement and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for Complete removal of existing treatment and applying minimum 1.5 mm thick of Birla white or equivalent wall care putty to achieve smooth surfaces and applying two coats of Oil Bound Distemper of approved shade/tint over a coat of primert complete all as specified and as directed.

M&L for complete removal of existing surface of wall and applying two coats of cement base paint over one coat of primer complete all as specified and as directed.

M&L for preparation of old plastered or unplastered decorated wall surfaces and applying one coat of cement base paint complete all as specified and as directed.

M&L for complete removal of existing treatment and applying two coats of premium acrylic emulsion paint having VOC less than 50 gm/lit and UV resistance as per IS 15489:2004 Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted ) with silicon additives @ 1.43 liter /10Sqm over and including priming coat of exterior primer applied @ .90 liter/10 Sqm over new surfaces complete all as specified and as directed.

M&L for preparation of wood and wood based materials old surface of any description exc. 10cm width and girth other wise described applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth,not otherwise described applying one coat of synthetic enamel (ordinaty tint) at any height up to 12.00m complete all as specified and as directed.

Taking up or down 20 mm bore GI water tubing and connections, including removing form site complete all as specified and directed.

Taking up or down 15 mm bore GI water tubing and connections, including removing form site complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing complete all as specified and directed.

M&L for Cutting chases, of girth not exceeding 10 cm for concealed water tubing or concealed conduit wiring, etc. in stone / brick masonry wall built in cement mortar and making good, disturbed surface in Cement mortar 1:3 complete all as specified and directed.

S&F in repair 15mm bore stop cock cast copper alloy, fancy type, chromium plated, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed. .

S&F in repairs, 15mm bore pillar taps, cast copper alloy with capstan heads , fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair Chromium plated brassTowel rail of 20mm dia, D type, 60cm long between flanges including CP brass screws & wooden/plastic cleats complete all as specified and directed.

S&F in repair brass chromium plated shower roses with or without swivel joints 125mm size with CP long shank arm including fixing to steel pipe or union complete all as specified and as directed.

S & F in repairs, stop valves/ angular stop valve (concealed type), 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

M&L for grating doom 100mm dia PTMT all as specified and as directed.

S&F in repairs , 32/40 mm bore PVC flexible outlet pipes for wash basin /sink /urinal fixed complete all as specified and as directed

S & F in repairs, PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

M&L in repairs , for PVC (SWR) floor trap , plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1 all as specified and as directed.

S&F in repairs, CP health faucet (hand shower) with 8mm dia , 1200 mm long flexible tube , wall mounted / hooked all as specified and as directed.

S&F in repairs vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set including Plastic water closet seat cover white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC with 02 Nos PTMT nuts and rubber washer and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S & F in repair Vitreous china squatting pan of pattern Orissa Pattern of size 580x 440 mm white with 110mm bore PVC ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( 1:5:10, using 40 mm graded stone aggregates), and finishing the top surfaces to match with the existing flooring as in repairs complete all as specified and directed

S & F in repairs vitreous china wash Oval shaped wash hand basin of size 560 x 400 mm, white flat back including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs for vitreous China bowl urinal bowl type or half stall pattern back, with grating and union for discharge pipe (excluding flushing cistern, flush pipe) including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), PVC connection, 40mm PVC waste pipe & 40 mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, complete all as specified and as directed.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. with grating and union for discharge pipe all as specified and as directed by Engineer-In-Charge.

Supply & Fixing drapery / curtain rod fancy type made out of 25mm dia MS conduit having PVC powder coated pipe bright finish colour and pattern including matching end finial as approved by Engrin-charge complete all as specified & directed.

Supply & Fixing MS brackets with hold fasts suitable for drapery rod / curtain rod 25mm dia and fixed to wall (concrete/ brick masonary) with the help of 2Nos 50mm long steel screws and rawl plug including drilling with electric drill and making good the disturbed surface complete all as specified & directed.

S&F in repair FRP diving boards of size 4.80m long,0.50m width and 45 to 65 mm thickness tapered, made of burma teak wood laminated with 99.70 % water resistant polyster resin compositely reinforced with CSM-450 chopped fiber glass strand mat molded with anti slippery top laminated with WR-300 mat thickness, including providng and fixing of MS fulcrum with roller of stainless steel back swing rubber coated rolled stand with steering and hinges for diving board of make as approved by GE. Note - Fixing / installation of FRP diving boards to be done by company authorised skilled workers.

M&L Welding in repairs n exc 2.5cm in length and thickness of metal to be welded not exc 6 mm all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, bell push, holders, ceiling roses, pendants, regulators, sockets etc but excluding DBs, light fittings etc and making good disturbed surfaces of walls, floors etc. and matching with existing surface all as specified and as directed.

M & L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,PVC insulated and unsheathed , FRLSH cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLSH cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards for mounting switches, sockets, fan Regulators, accessories etc as specified and directed for one light point or one fan point controlled by one, one way switch . NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2. All points shall be earthed up to fixtures i.e holders,tube lights,ceiling lights,bldg security lights etc.

(a) All as per serial item No. 83 here in before but one 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified.

(b) All as per serial item No. 83 here in before but on independent board.

(c) All as per serial item No. 83 herein before but with 2.5 Sqmm, PVC copper stranded cable FRLSH type for phase,Neutral and earth for one 15 Amp, 6 pin socket on independent board.

S&F switch piano, flush button, 5 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.

S&F socket outlet, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way suitable for 3 pin/2pin, 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin ) 5/15 Amps, 230V, AC. all as specified & as directed.

Supply and fix in replacement lamp holder, PVC / Polycarbonate type with back plate suitable for LED bulbs all as specified & as directed..

Supply and Fixing in replacement LED bulb of capacity upto 12 watt complete with all as specified & as directed.

Supply and fix in replacement ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish.

Supply & fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep.Five star rated with brushless direct current motor (BLDC) with out remote including taking down old Ceilingt fan all as specified & directed. Note: Quoted rates includesTaking down of ceiling Fan and deposited to MES Store Yard.

S & F in replacement square profile LED lighting fixture with extruded polycorbonate,environmental friendly,energy efficient ready to use pack LED Tube light fitting 20 Watt with LED light source 6500k with uniform light output,with all accessories including its connection complete with all as specified and directed by Engineer-in-charge.

S & F in replacement square profile LED lighting fixture with extruded polycorbonate,environmental friendly,energy efficient ready to use pack LED Tube light fitting 10 Watt with LED light source 6500k with uniform light output,with all accessories including its connection complete with all as specified and directed by Engineer-in-charge.

S&F in replacement, 600 mm x 600 mm x 35 mm size,230 vollts 40 watt LEDs luminaire fixture, with driver, ultra modern , surface mounting, suitable for amstrong / grid ceiling in MS housing with high brightness, prewired, including connections from ceiling rose to light fittings,complete all as specified & as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450 mm sweep with, blades, and frame and louvers including taking down old exhaust fan all as specified & directed. Note: Quoted rates includesTaking down of Exhaust Fan and deposited to MES Store Yard.

S&F in replacement,LED security light fitting of building with single piece new generation energy saving and environmental friendly, long life, LED 60W, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of light grade GI Pipe 40 mm dia, 1.5 mtr long, fixed to wall with two clamps made out of mild steel flat iron 40 mm x 5 mm and connect to nearest electric supply by three core 1.5 sqmm copper cable all as specified and as directed.

S&F in replacement,LED Flood light fitting of capacity 160 watt single piece new generation energy saving and environmental friendly, long life, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including fixed to wall with one bracket suitable clamps,nuts,bolts, and connect to nearest electric supply by three core 1.5 sqmm copper cable all as specified and as directed.

S&F in replacement,LED Flood light fitting of capacity 50 watt single piece new generation energy saving and environmental friendly, long life, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including fixed to wall with one bracket suitable clamps,nuts,bolts, and connect to nearest electric supply by three core 1.5 sqmm copper cable all as specified and as directed.

S&Fin replacement, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), Tripple pole and neutral, 415 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F in replacement, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 8 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed

S&F in replacement, on load change over switch 440 Volts in sheet metal enclosures four pole 63 Amps capacity complete all as specified and as directed.

S&F in replacement, MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in replacement, MCB SPN, AC 240 V, 32 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in replacement, MCB TPN, AC 440 V, 63 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in replacement sheet metal enclosures with plug socket, Tripple pole and neutral with three pin and earth plug with one MCB of 63 Amps (TPN) complete all as specified and as directed.

S & F in replacement PVC weather proof, hinged door, junction box with Aluminium bus bar, 240V, Neutral link and 1No MCB SP of 6 Amps, necessary fixing arrangement such as clamps, nut, bolts, etc all as specified and directed.

M&L for submain wiring with four single core PVC insulated unsheathed, multistranded flexible FRLSH copper conductor 1100 volts grade cables 4 sqmm drawn through in and including heavy duty PVC rigid conduits 20mm or higher dia as reqd at site, totally concealed in walls/floors including conduit accessories etc. including one single core 4 sqmm 1100 volts grade PVC insulated unsheathed multi stranded flexible FRLSH copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified & directed. Notes: 1. Unit rate includes for cutting chases for conduits and making good to wall floors etc. 2. five runs (4+1) of single core FRLSH PVC insulated unsheathed multi stranded flexible copper conductor and one run of PVC conduit heavy duty shall be measured as one unit.

Supply, install, and commissioning and testing in repairs factory made and tested (including CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compartmantalised and IP-65 suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, all as specified and directed, having bus bar chamber with insulated copper bus bars 300 amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, made of 3.15mm CRCA MS sheet and with base frame of 50x50x6mm angle iron , powder coated, having front and rear openiable hinged double door shuters with aprons for cable entry and locking arrangement complete.(Notes : The rate quoted shall include for earth work & excavation for angle iron frame for foundation of panel board upto 0.50 m below GL in any type of soil & PCC (1:4:8), D2 filling in foundation the ground clearance of panel board shall be 0.40 m GL to the bottom of panel board ). Note:(i)Panel board shall be approved by CPRI and certificate to be produced and to be submitted in the office.(ii) Panel Board should be fixed at Swimming Pool.

M & L in replacement Earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.0 mm thick buried directly in ground in any type of strata (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI strip 32 x 6mm, by means nut bolt, nuts, check nuts and washer of the GI Earth strip protected by provision of GI light grade pipe 40 mm incl provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregated with 40 mm thick cover with RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2020 and connection to earth test point all as specified incl testing on completion”.Note:The unit Rate includes earth strip and protection pipe up to (max 7.5 metre) from earth plate/earth point/test point.

M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.

Dismantling of Heavy duty Steel, Horizontal, cylindrical type, Pressure Media Filter having a capacity of 60000 GPH, emptying filter media from Existing MS filter, dismantling of piping from header to filter, Sluice valves. Gas cutting of MS vessel, suction piping of pumps from pump to suction tank and submitted above old U/S items safely to MES Store Yard all as specified and directed by Eng-in-charge. (NOTE :- Cost deemed to include the transportation and manpower required for shifting of UNSV filter & fittings to MES store yard at GE(South) Ahmednagar.

Supply,installation, testing and commissioning of Factory made Vertical cylindrical type multi grade pressure sand filter capacity of minimum 110 cum / hour fabricated from MS sheet of shell thickness of 6mm and dish end thickness of 8mm. Filter shall be of size 2200 mm dia , 1875 mm HOS, duly painted (inner & outer) with red oxide primer and two coats of epoxy paint complete with suitable size of inlet &outlet valves, NRVs, control valves for operation,pressure gauge at inlet and outlet line, with Backwashing provision including valve manifold, drain out facilities complete, including 150 mm dia. MS frontal piping with suitable sizes pipes for discharge of 80 cum /hour and pressure rating minimum 2.5 Kg/cm2 with all necessary fittings, with filter media quantity 6560 KGS & media depth of 915 mm, filteration velocity of 25 m3/m2/hr, etc complete all as required for smooth function and operation all as per manufacturer/OEM design discharge capacity and instructions . Make- Ion Exchange India Ltd /Pentair or equivalent as approved by GE. Note: 1. Rate quoted shall be inclusive of MS frontal piping, control valves connected to the pressure filter complete with all accessories. 2.Rate quoted shall be inclusive of PCC/RCC foundation required for installation of vertical cylindrical type muti grade pressure sand filters of suitable size as per OEM instructions. 3. Piping up to pressure filter in-let & beyond out let of pressure filter and drain pipe shall be measured and paid separately under respective item.

Supply, installation, connection and testing of MSEP/UPVC pipe confirming to IS :4985 Class IV 10Kg/Cm2 and Interconnecting Piping work for all four MGF 2200 dia filter including all necessary fittings such as bends ,elbow ,reducers ,tees ,union coupler tail piece flange, etc as required at site to make good the connections complete all as specified and directed by Engineer-in-Charge. NOTE:-Cost shall be inclusive for providing supports as per specification and making good pipes shall be connected to pumps, equipment ,valves etc through tail piece Flange 150 mm diameter.

Supply, installation, testing and commissioning of chlorine /PH correction dosing pump CDS 3, 0 - 6 LPH with PP/PVC dozing tank capacity 150 LTR- 1 No and piping for inlet & outlet connection complete with control valves, NRV, metering, electric cabling & copper wiring through PVC conduit from Main control panel to booster pump. Make: Ion Exchange /Voltas /Eureka Forbes or equivalent as approved by GE

Supply installation, test and commissioning of Alum or poly dosing CDS 3 -Dosing pump (venture drive pump) 0 - 6 LPH with PP/PVC dozing tank capacity 150 LTS with high speed stirrer and piping for inlet & outlet connection complete with control valves, NRV ,electric cabling & copper wiring through PVC conduit from Main control panel to booster pump. Make: Ion Exchange /Voltas /Eureka Forbes or equivalent as approved by GE

Supply installation, testing and commissioning of Air Blower with suitable 3 PH motor IE-2 rated , ISI marked required for filtration unit back wash process of suitable capacity but not less than 250 Cum /Hr , or as recommended by OEM for swimming pool as given in schedules – Make:- Ion Exchange /A1 Blower /Everest or equivalent as approved by GE

Supply installation, testing and commissioning of heavy duty high performance and high efficiency Suction Sweeper Submersible Pump 2HP, 415 V, 3 Phase, 2850RPM, having 50 mm dia delivery including all connecting acceessory like Nylon Brushes, Filters, Cable, Pulling Pipes complete all as specified and as directed. Make:- Mody/Kirloskar/Crompton /KSB

Vinod Enterprises

M/s. N D Karande

OM SAI ASSOCIATES

MS. G.A. CONSTRUCTION