Special repair to Electrical work at JNV Balasore (Odisha)

Sl. No. Description Amount DSR Amount Non-DSR

School Building 7,64,463.00 3,68,133.50

Staff Quarter 16,83,370.00 7,33,191.00

Principal Quarter 4,38,013.00 50,481.50

Group D Quarter 21,11,002.00 4,38,630.00

Kitchen & Dining 6,72,173.00 2,68,821.00

Boys Dormitory For 320 nos of Students 10,06,907.00 3,58,596.00

Girls Dormitory For 240 nos of Students 9,32,130.00 2,76,822.00

External Electrical Works 2,31,131.00 26,12,631.05

Electric Sub Station building works 11,15,322.79 2,23,079.73

Total Cost Of Work 1,54,80,234.57

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF EXTERNAL ELECTRICAL WORK AT JNV, BALASORE, ODISHA

Amount on DSR - Amount on

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) Non DSR (In Rs)

G. DSR 2022 Repairs to Internal Wiring and Fans/Light Fittings

Design, fabrication, assembly, wiring and supply of front operated dead front cubicle

type compartmentalised as per Form 3B, rear access free standing, dust and vermin

proof (IP42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase

4 wire 50 Hertz system suitable for a symmetrical fault level of 50kA at 415 volts,

fabricated from 2 mm thick CRCA MS Sheets with hinged, gasketted, (metal based

neorene) and lockable doors having structural reinforcement with suitable

angle/channel/T/flat sections including 3 mm thick gland plates on top & bottom and

including lifting hooks and including GI earth strip of required size with 2 nos. earthing

terminals and including powder coated paint finish of approved shade over metal

surface cleaned and treated with seven tank process complete with interconnections

etc. as per specifications as required and as below.

(Note: The contractor may select next higher fault rating of MCCB if it is not readily

available, without any extra cost, as the figure indicated within the bracket are required

maximum fault level of the panel.)

The panel must be as per IC 60439 PTTA type from any India Based Test Laboratory

(CPRI/ERDA etc.) for protectiion against short circuit/temperature rise /internal arc/

degree of protection

1 NS-1 LT panel Emergency Panel

Supply, Installation, Testing & Commissioning of 58.5 kVA DG Set AMF panel

including power contractor (Main & DG), and all panel accessories wit AUTO/MANUAL

selector switch alongwith cost of materials, labour, T&P and transportation etc as per

the direction of Engineer-In-Charge

Incomer from DG Set-1 (58.5 kVA)

1 nos. 100A 4P MCCB, 25kA breaking capacity wit thermal release and rotatary handle.

Metering & Indication

1 set of RYB phase indicating lamps each with 3 nos. 2A SP MCBs

Digital multifunction meter for Voltage, current & KW with selector switch Each with 3

nos. of 2A SP MCCB & 3nos. 100/5A CTs (100A/500V) rating 1 Nos.

1 sets of ON/OFF/Trip/Spring Charged & Trip circuit healthy indicating lamps

1 set of 125A TPN Aluminium bars with colour coded PVC Sleeves

3 Nos 63A, TPN, MCCB, 15kA breaking capacity with Thermal Magnetic release &

rotatary handle with adjustable settings , ON/OFF/Trip Indication lamps including

control MCBs inserted energy meters with 1 outgoing

3 Nos 63A, TPN, MCB, 10kA breaking capacity

Supplying, Receiving, fixing, testing & commissioning of above described panel

Incomer from Transformer (Transformer-1, 250 kVA)

Each incomer shall consist of the following

1 nos. 400 A, FP MCCB, 35kA breaking capacity with microprocessor release and

adjustable setting and with rotatory handle

1 sets. Digital multifunction meter (showing harmonics along with all other electrical

parameters such as Voltage, current & KW with RS 485 port with matching cast resin CTs

1 nos. indicating lamps for MCB on/off trip with protective SP MCBs

1 sets of CTs of the ratio 400/5A for APFC Relay burden 15VA

1 sets of CTs of the ratio 400/5A with class 0.5 accuracy for metering, burden 15VA

1 nos. 400/5A, 15 VA, 5P10 CTs for Protection

1 Nos. under voltage relay (59)

1 Nos. over voltage relay ( 27)

Negative phase protection relay, reverse power relay

1 set of 500A TPN Aluminium bars with colour coded PVC Sleeves

1 Nos 200A, TPN, MCCB, 35kA breaking capacity with microprocessor release & rotatary

handle with adjustable settings , ON/OFF/Trip Indication lamps including control MCBs

1 Nos 160A, TPN, MCCB, 25kA breaking capacity with thermal release & rotatary handle

with adjustable settings , ON/OFF/Trip Indication lamps including control MCBs

6 Nos 100A, TPN, MCCB, 25kA breaking capacity with thermal release & rotatary handle

with adjustable settings , ON/OFF/Trip Indication lamps including control MCBs

6 Nos 63A, TPN, MCCB, 25kA breaking capacity with thermal release & rotatary handle

with adjustable settings , ON/OFF/Trip Indication lamps including control MCBs

Supplying, Receiving, fixing, testing & commissioning of Main LT Panel as described

Design, manufacturing, supplying, fixing in position testing & commissioning of the

following front operated front access2 mm thick CRCA steel enclosures free standing,

dust and vermin proof outdoor type feeder pillar with IP55 ingress protection) hinged

and lockable doors complete with interconnections copper crimping lugs, brass glands

bonding to earth and painting suitable for use at 415 volts, 3 phase 4 wire 50 Hertz

system. The panel faults withstanding capacity shall be 25 mva at 415 volts. All live

accessories shall be shrouded and all equipment shall be finger touch proof.The bus bar

shall be of colour coded with heat shrinkable PVC insulated sleeves.

2 NS-2 FEEDER PILLAR-1

Digitally signed by JAYA

Amount on DSR - Amount on

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) Non DSR (In Rs)

1 nos. 125A FP MCCB, 25kA breaking capacity with thermal release and rotatary handle.

Metering & Indication

1 set of RYB phase indicating lamps each with 3 nos. 2A SP MCBs

Digital multifunction meter for Voltage, current & KW with selector switch Each with 3

nos. of 2A SP MCCB & 3nos. 100/5A CTs (100A/500V) rating 1 Nos.

1 sets of ON/OFF/Trip/Spring Charged & Trip circuit healthy indicating lamps

1 set of 160A TPN Aluminium bars with colour coded PVC Sleeves

7 Nos 63A, FP MCCB

Supplying, Receiving, fixing, testing & commissioning of above described panel Set 1.00 248819.13 248819.130

Supplying,installation, testing & commissioning of the M.V cubicle type totally enclosed

dust and vermin proof Meter boards complete with bus bars, MV danger notice, plate

on surface ISI marked electronic kWH meter, indication lamps, CTs, Interconnection with

suitable capacity aluminium strips, /rods, door cover, separate compartment for each

meters, glass inspection window , connection of incoming & outgoing cables with

thimbles, powder coated having incoming & outgoing MCBs, MCCBs, and kWh meters

complete as required

3 NS-3 Panel-Kitchen Dining

1 nos. 40A FP MCCB, 15kA breaking capacity with thermal release adjustable setting and

rotatary handle.

Metering & Indication

1 set of RYB phase indicating lamps each with 3 nos. 2A SP MCBs

Digital multifunction meter for Voltage, current & KW with selector switch Each with 3

nos. of 2A SP MCCB & 3nos. 100/5A CTs (100A/500V) rating 1 Nos.

1 sets of ON/OFF/Trip/Spring Charged & Trip circuit healthy indicating lamps

1 set of 50A TPN Aluminium bars with colour coded PVC Sleeves

2 Nos 25A, TPN MCB of 10kA

3 Nos 40A, DP MCB of 10kA

Supplying, Receiving, fixing, testing & commissioning of above described panel Set 1.00 90479.69 90479.690

4 NS-4 Meter Board-Staff Quarters

1 nos. 63A FP MCCB, 15kA breaking capacity with thermal release adjustable setting and

rotatary handle.

Metering & Indication

1 set of RYB phase indicating lamps each with 3 nos. 2A SP MCBs

Digital multifunction meter for Voltage, current & KW with selector switch Each with 3

nos. of 2A SP MCCB & 3nos. 100/5A CTs (100A/500V) rating 1 Nos.

1 sets of ON/OFF/Trip/Spring Charged & Trip circuit healthy indicating lamps

1 set of 100A TPN Aluminium bars with colour coded PVC Sleeves

4 Nos 40A, TPN MCB of 10kA

2 Nos 40A, DP MCB of 10kA

Supplying, Receiving, fixing, testing & commissioning of above described panel Set 3.00 117623.59 352870.770

4 NS-4 Panel- School Building

1 nos. 63A FP MCCB, 15kA breaking capacity with thermal release adjustable setting and

rotatary handle.

Metering & Indication

1 set of RYB phase indicating lamps each with 3 nos. 2A SP MCBs

Digital multifunction meter for Voltage, current & KW with selector switch Each with 3

nos. of 2A SP MCCB & 3nos. 100/5A CTs (100A/500V) rating 1 Nos.

1 sets of ON/OFF/Trip/Spring Charged & Trip circuit healthy indicating lamps

1 set of 100A TPN Aluminium bars with colour coded PVC Sleeves

4 Nos 40A, TPN MCB of 10kA

3 Nos 40A, DP MCB of 10kA

Supplying, Receiving, fixing, testing & commissioning of above described panel Set 1.00 143259.50 143259.500

Sub Head-II- Supplying & Laying of Cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1

KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

7.5.2 Above 35 sq. mm and upto 95 sq. mm Mtrs 200.00 57.00 11400.000

7.5.3 Above 95 sq. mm and upto 185 sq. mm Mtrs 150.00 77.00 11550.000

7.5.4 Above 185 sq. mm and upto 400 sq. mm Mtrs 134.00 0.000

Supply of following sizes of XLPE insulated aluminium conductor strip/wire armoured,

2 NS-1 overall PVC sheathed 1.1kV grade cables conforming to IS 7098, and technical

Digitally signed by JAYA

Amount on DSR - Amount on

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) Non DSR (In Rs)

Supplying and making end termination with brass compression gland and aluminium

3 9.10 lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium

conductor cable of 1.1 KV grade as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground

complete with RCC collars jointing with stiff mixture of cement mortar in the proportion

of 1:2 (1 cement : 2 fine sand) including trenching (75cm deep) and refilling etc. as

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc. conforming to IS 14930. Part II complete with

5 14.16.1 fitting and cutting, jointing etc. direct in ground (75cm below ground level) including

excavation and refilling the trench but excluding sand cushing and protective covering

etc. complete as required.

14.16.1 63mm dia (OD-63 mm & ID-51 mm nominal) Mtrs 150.00 247.00 37050.000

14.16.2 90mm dia (OD-90 mm & ID-76 mm nominal) Mtrs 200.00 290.00 58000.000

Repairs to Internal Wiring and Fans/Light Fittings Total : 2,31,131.00 26,12,631.05

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF ELECTRICAL SUB STATION WORK AT JNV, BALASORE, ODISHA

Amount on DSR - Amount on Non

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) DSR (In Rs)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),

1 2.8.1 including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting

out the excavated soil and disposal of surplus excavated soil as directed, within a lead of

2.8.1 All kinds of soil cum 15.14 260.30 3939.64

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations

2 2.25 etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by cum 10.60 196.00 2076.62

ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete.

Excavating, supplying and filling of local earth (including royalty) by mechanical

4 2.25a transport upto a lead of 5km also including ramming and watering of the earth in cum 11.05 700.50 7740.53

layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to plinth

1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate

40 mm nominal size)

Providing and laying damp-proof course 40 mm thick with cement concrete

6 4.10 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm sqm 3.16 410.85 1298.29

Extra for providing and mixing water proofing material in cement concrete work in doses 50kg

by weight of cement as per manufacturer's specification. cemen

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality

8 4.13 using 1.7 kg per square metre on damp proof course after cleaning the surface with sqm 3.16 146.15 461.83

brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick

ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand,

including finishing the top smooth

Brick edging in full brick width and half brick depth including

excavation, refilling and disposal of surplus earth lead upto 50 metres.

With common burnt clay F.P.S. (non modular) bricks of

class designation 7.5

Centering and shuttering including strutting, propping etc. and removal

5.9.1 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 6.10 392.15 2390.15

5.9.3 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 33.04 927.25 30631.70

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.16.1 Edges of slabs and breaks in floors and walls: under 20cm wide rm 17.58 208.55 3666.31

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars qtl 7.81 10785.00 84176.93

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

5.22.A6 Thermo-Mechanically Treated bars qtl 10.00 10785.00 107850.00

14 5.30 Add for plaster drip course/groove in plastered surface or moulding to RCC projections rm 37.34 78.40 2927.46

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design

mix shall be payable separately.

In case the cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to either re-design

the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of grade M25 with minimum cement content of 330kg/cum

5.33.1 RCC work in footing cum 3.10 9504.75 29417.20

RCC work in beams cum 1.41 9504.75 13354.17

RCC work in columns cum 0.27 9504.75 2566.28

All works above plinth level

Concrete of grade M25 with minimum cement content of 330kg/cum

Digitally signed by JAYA

Amount on DSR - Amount on Non

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) DSR (In Rs)

16 5.33.1 RCC work in lintel cum 0.14 9860.40 1380.46

RCC work in beams cum 1.31 9860.40 12867.82

RCC work in columns cum 0.81 9860.40 7986.92

RCC work in slabs cum 4.30 9860.40 42350.42

Brick work with non modular fly ash lime bricks (FALG Bricks) conforming to IS:12894,

class designation 10 average compressive strength in super structure above plinth level

up to floor V level in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of

17 6.1.2 class designation 7.5 in foundation and plinth in: cum 3.38 7132.25 24071.34

Cement mortar 1:6 (1 cement : 6 coarse sand)

Wood and PVC Work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and

well matched commercial 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters :

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

19 9.23 minimum depth on all edges of flush door shutters (over all area of door sqm 2.52 462.35 1165.12

shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S.

21 9.48.1 flats, square or round bars etc. including priming coat with approved steel primer all kg 26.73 219.10 5856.54

complete.Fixed to steel windows by welding

Providing and fixing oxidised M.S. casement stays (straight peg type)

with necessary screws etc. complete.250 mm weighing not less than 150 gms

Providing and fixing aluminium hanging floor door stopper, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade, with necessary screws

etc. complete.Twin rubber stopper

Providing and fixing bright /matt finished Stainless Steel handles of approved

quality & make with necessary screws etc all complete. 125mm

Providing & fixing stainless steel sliding door bolts ISI marked anodised (anodic coating

25 MR not less than AC 10 as per IS 1866) transparent or dyed to required colour or shade with nos. 2.00 560.00 1120.00

nuts and screws etc complete 250x16mm

Providing and fixing stainless steel tower bolts (barrel type ) with necessary screws etc.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths,

interlocked together through their entire length and jointed together at the end by end

locks, mounted on specially designed pipe shaft with brackets, side guides and

arrangements for inside and outside locking with push and pull operation complete,

including the cost of providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required thickness

for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 3.13 3653.20 11416.25

28 10.70 Providing and fixing ball bearing for rolling shutters. nos. 1.50 492.35 738.53

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar

29 10.90 instead of laths as per design approved by Engineer-in- charge, (area of grill to be sqm 0.75 768.25 576.19

Providing and fixing factory made ISI marked steel glazed doors, windows and

ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11

B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt

welded and sash bars tenoned and riveted, including providing and fixing of hinges,

30 10.11.1 pivots, including priming coat of approved steel primer, but excluding the cost of other kg 9.72 131.05 1273.81

fittings, complete all as per approved design, (sectional weight of only

steel members shall be measured for payment).

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm

of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard

with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred,

welded and grinded finish, with profiles of required size, including fixing of necessary

butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard

with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred,

welded and grinded finish, with profiles of required size, including fixing of necessary

butt hinges and screws and applying a priming coat of approved steel primer.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses

etc., including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer, including welding and bolted with special shaped washers etc.

complete. Electric resistance or induction butt welded tubes

Providing & fixing glass panes with putty and glazing clips in steel doors,

windows, clerestory windows, all complete with :4.0 mm thick glass panes

Digitally signed by JAYA

Amount on DSR - Amount on Non

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) DSR (In Rs)

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed

with neat cement slurry mixed with pigment to match the shade of tiles, including

35 11.20.2 rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 sqm 3.15 1328.35 4184.30

cement: 4 coarse sand).Medium shade pigment using 50% white cement 50%

Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade

36 11.26.1 of the slab, including rubbing and polishing complete with base of cement sqm 32.00 1948.25 62344.00

mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm

(average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey

cement slurry mixed with pigment to match the shade of the slabs, including rubbing

and polishing complete.

Providing and laying factory made coloured chamfered edge Cement Concrete paver

blocks of required strength, thickness & size/shape, made by table vibratory method

using PU mould, laid in required colour & pattern over 50mm thick compacted bed of

fine sand, compacting and proper embedding/laying of inter locking paver blocks into

the sand bedding layer through vibratory compaction by using plate vibrator, filling the

joints with jamuna sand and cutting of paver blocks as per required size and pattern,

finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic

parking etc. complete as per manufacturer's specifications & direction of Engineerin-

Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design &

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated

with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface

with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete

:With residual type petroleum bitumen of grade VG - 10

Supplying and fixing of prepainted coloured trapezoidal or approved profiled sheeting

1000-1020mm cover width, 28-30 mm high crests with subtle square flutting in the five

pan at nominal 190-255mm as approved by EIC centre to centre manufactured out of

0.50mm TCT hitensile prepainted zincalume/galvalume steel (AZ-150 gsm. Aluminium -

Zinc alloy metallic coating of total both sides 550Mpa yield stress as per AS 1397.

Colour/exterior coat of RMP 20 micron top coat applied over 5 micron primer and a 5

micron polyester back coat applied over 5 microns primer or equivalent

coating/painting. The sheet shall have wide pans with stiffening ribs for effective water

shedding and special male female ends with full return legs on side laps for purlin

support. The male end of the sheet shall have anti capillary flute at side laps to prevent

leakages. The sheet shall be fixed by means of anti corrosive approved make "rust

shield" (Epoxy polymer) coated self drilling self tapping fasteners 12-14x 55mm with

EPDM seals through crest for roofing and 12-24 x20 mm through valley (pans) for wall

cladding. The sheet shall be supplied in lengths maximum up to 6-12 meter long to suit

site dimensions. The scope includes all sealing of joint, curves, edges or other

accessories with

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses

etc., including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer, including welding and bolted with special shaped washers etc.

complete. Electric resistance or induction butt welded tubes

15 mm cement plaster on rough side of single or half brick wall of mix :1:6 (1 cement: 6

12 mm cement plaster on fair side of single or half brick wall of mix :1:6 (1 cement: 6

44 13.16.1 6mm cement plaster on ceiling a) 1:3 (1 cement: 3 fine sand) sqm 35.00 300.45 10515.75

Distempering with oil bound washable distemper of approved brand and manufacture

to give an even shade :

13.41.1 New work (two or more coats) over and including water thinnable priming coat

with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of

required shade :

13.47.1 New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including

priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Applying priming coat

With ready mixed aluminium primer of approved brand and manufacture on resinous

wood and plywood

With ready mixed red oxide zinc chromate primer of approved brand and manufacture

on steel galvanised iron/ steel works

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as

49 13.52.1 per manufacturer's specifications including appropriate priming coat, preparation of sqm 32.00 241.75 7736.00

surface, etc. complete.On steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an

13.61.1 Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of

51 13.80 approved brand and manufacturer, over the plastered wall surface to prepare the sqm 33.35 156.05 5203.50

surface even and smooth complete.

52 MR Providing & fixing GI chain link fencing with in mesh size 50x50mm sqm 43.00 3801.65 163470.95

Repairs to Internal Wiring and Fans/Light Fittings Total : 1115322.79 223079.73

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF SCHOOL BUILDING - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

G. DSR 2022 Repairs to Internal Wiring and Fans/Light Fittings

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

118 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

120 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 50.000 334.00 16700.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

122 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

123 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

124 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

126 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

127 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 10.000 69.00 690.000

Supplying and fixing two module stepped type electronic fan

128 1.25 regulator on the existing modular plate switch box including Each 132.000 369.00 48708.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

129 1.29 phenolic laminated sheet cover in front including providing and Each 20.000 358.00 7160.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

130 1.30 phenolic laminated sheet cover in front including providing and Each 20.000 488.00 9760.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

131 1.33 junction box/ wooden block including connections etc. as Each 120.000 87.00 10440.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

134 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 10.000 599.00 5990.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

141 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 20.000 706.00 14120.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

145 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

149 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 75.000 339.00 25425.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

150 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

153 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 75.000 2837.50 212812.500

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

155 MR standard item with copper wiring, control gears and lamps as required as per the Each 8.000 2812.00 22496.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Repairs to Internal Wiring and Fans/Light Fittings Total : 7,64,463.00 3,68,133.50

Digitally signed by JAYA

NAME OF WORK:- REPAIR WORK OF 7no. OF STAFF QUARTERS - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

G. DSR 2022 Repairs to Internal Wiring and Fans/Light Fittings

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

75 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

77 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 150.000 334.00 50100.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

79 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

80 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

81 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

83 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

84 1.23 existing switch box/ cover including connections etc. as

Digitally signed by JAYA

Supplying and fixing two module stepped type electronic fan

85 1.25 regulator on the existing modular plate switch box including Each 84.000 369.00 30996.000

connections but excluding modular plate etc. as required.

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

86 1.29 phenolic laminated sheet cover in front including providing and Each 80.000 358.00 28640.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

87 1.30 phenolic laminated sheet cover in front including providing and Each 50.000 488.00 24400.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

88 1.33 junction box/ wooden block including connections etc. as Each 112.000 87.00 9744.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

91 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

93.1.1 2.10.2 Single pole and neutral Each 10.000 599.00 5990.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

98 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 70.000 706.00 49420.000

bolt, spring, washer excavation and re-filling etc. as required.

Digitally signed by JAYA

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

102 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting /

compact fluorescent fitting of all types, complete with all accessories and

105 1.41 tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. Each 80.000 206.00 16480.000

mm FRLS PVC insulated, copper conductor, single core cable and earthing

etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

106 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 84.000 339.00 28476.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

107 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with

all accessories and tube etc

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting

complete with all accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod,

110 MR blades, 2 nos. caps & regulator etc. ISI with 5 star marked & energy efficient Each 84.000 2837.50 238308.000

complete as required. 1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts,

bolts, mounting FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures

complete as per standard item with copper wiring, control gears and lamps

as required as per the satandard catalouge item..(Such as Decon Cat. No.

L05AAM - 2x 12 or Equivalent).

Repairs to Internal Wiring and Fans/Light Fittings Total : 16,83,370.00 7,33,191.00

Digitally signed by JAYA

NAME OF WORK:- REPAIR WORK OF PRINCIPAL QUARTERS - JNV, BALESORE, ODISHA

Amount on DSR - Amount on

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) Non DSR (In Rs)

G. DSR 2022 Repairs to Internal Wiring and Fans/Light Fittings

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

75 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

77 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 100.000 334.00 33400.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

79 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

80 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 0.000 894.00 0.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

81 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

83 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Digitally signed by JAYA

Supplying and fixing following piano type switch/ socket on the

84 1.23 existing switch box/ cover including connections etc. as

Supplying and fixing two module stepped type electronic fan

85 1.25 regulator on the existing modular plate switch box including Each 5.000 369.00 1845.000

connections but excluding modular plate etc. as required.

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

86 1.29 phenolic laminated sheet cover in front including providing and Each 10.000 358.00 3580.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

87 1.30 phenolic laminated sheet cover in front including providing and Each 10.000 488.00 4880.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

88 1.33 junction box/ wooden block including connections etc. as Each 10.000 87.00 870.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

91 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

93.1.1 2.10.2 Single pole and neutral Each 5.000 599.00 2995.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Digitally signed by JAYA

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

98 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 20.000 706.00 14120.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

102 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting /

compact fluorescent fitting of all types, complete with all accessories and

105 1.41 tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. Each 6.000 206.00 1236.000

mm FRLS PVC insulated, copper conductor, single core cable and earthing

etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

106 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 5.000 339.00 1695.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

107 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with

all accessories and tube etc

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting

complete with all accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod,

110 MR blades, 2 nos. caps & regulator etc. ISI with 5 star marked & energy efficient Each 5.000 2837.50 14187.500

complete as required. 1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts,

bolts, mounting FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures

complete as per standard item with copper wiring, control gears and lamps

as required as per the satandard catalouge item..(Such as Decon Cat. No.

L05AAM - 2x 12 or Equivalent).

Repairs to Internal Wiring and Fans/Light Fittings Total : 4,38,013.00 50,481.50

Digitally signed by JAYA

NAME OF WORK:- REPAIR WORK OF PRINCIPAL QUARTERS - JNV, BALESORE, ODISHA

Amount on DSR - Amount on

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs)

2023 (In Rs) Non DSR (In Rs)

G. DSR 2022 Repairs to Internal Wiring and Fans/Light Fittings

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

75 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

77 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 300.000 334.00 100200.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

79 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

80 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

81 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

83 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Digitally signed by JAYA

Supplying and fixing following piano type switch/ socket on the

84 1.23 existing switch box/ cover including connections etc. as

Supplying and fixing two module stepped type electronic fan

85 1.25 regulator on the existing modular plate switch box including Each 15.000 369.00 5535.000

connections but excluding modular plate etc. as required.

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

86 1.29 phenolic laminated sheet cover in front including providing and Each 30.000 358.00 10740.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

87 1.30 phenolic laminated sheet cover in front including providing and Each 30.000 488.00 14640.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

88 1.33 junction box/ wooden block including connections etc. as Each 30.000 87.00 2610.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

91 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

93.1.1 2.10.2 Single pole and neutral Each 15.000 599.00 8985.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Digitally signed by JAYA

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

98 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 0.000 706.00 0.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

102 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting /

compact fluorescent fitting of all types, complete with all accessories and

105 1.41 tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. Each 120.000 206.00 24720.000

mm FRLS PVC insulated, copper conductor, single core cable and earthing

etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

106 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 45.000 339.00 15255.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

107 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with

all accessories and tube etc

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting

complete with all accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod,

110 MR blades, 2 nos. caps & regulator etc. ISI with 5 star marked & energy efficient Each 45.000 2837.50 127687.500

complete as required. 1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts,

bolts, mounting FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures

complete as per standard item with copper wiring, control gears and lamps

as required as per the satandard catalouge item..(Such as Decon Cat. No.

L05AAM - 2x 12 or Equivalent).

Repairs to Internal Wiring and Fans/Light Fittings Total : 21,11,002.00 4,38,630.00

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF 0.5 UNIT FOR 96 nos OF BOYS - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

G. DSR 2022 Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

102 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

104 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 25.000 334.00 8350.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

106 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

107 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

108 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

110 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

111 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 5.000 69.00 345.000

1.23.5 6 pin 15/16 A socket outlet Each 5.000 137.00 685.000

Supplying and fixing two module stepped type electronic fan

112 1.25 regulator on the existing modular plate switch box including Each 40.000 369.00 14760.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

113 1.29 phenolic laminated sheet cover in front including providing and Each 5.000 358.00 1790.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

114 1.30 phenolic laminated sheet cover in front including providing and Each 5.000 488.00 2440.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

115 1.33 junction box/ wooden block including connections etc. as Each 40.000 87.00 3480.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

118 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 5.000 599.00 2995.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

125 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 20.000 706.00 14120.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

129 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

133 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 25.000 339.00 8475.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

134 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

137 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 40.000 2837.50 113500.000

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

139 MR standard item with copper wiring, control gears and lamps as required as per the Each 4.000 2812.00 11248.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Electrical Works Total : 5,49,974.00 2,21,860.50

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF M.P. HALL - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

G. DSR 2022 Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

37 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

39 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 10.000 334.00 3340.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

41 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

42 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 8.000 894.00 7152.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

43 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

45 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

46 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 5.000 69.00 345.000

1.23.5 6 pin 15/16 A socket outlet Each 5.000 137.00 685.000

Supplying and fixing two module stepped type electronic fan

47 1.25 regulator on the existing modular plate switch box including Each 3.000 369.00 1107.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

48 1.29 phenolic laminated sheet cover in front including providing and Each 2.000 358.00 716.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

49 1.30 phenolic laminated sheet cover in front including providing and Each 2.000 488.00 976.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

50 1.33 junction box/ wooden block including connections etc. as Each 2.000 87.00 174.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

53 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 1.000 599.00 599.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

60 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 25.000 706.00 17650.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

64 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

68 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 4.000 339.00 1356.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

69 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

72 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 25.000 2837.50 70937.500

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

74 MR standard item with copper wiring, control gears and lamps as required as per the Each 4.000 2812.00 11248.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Electrical Works Total : 2,66,554.50 1,56,948.00

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF KITCHEN & DINING - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

H. DSR 2022 Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

100 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

102 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 25.000 334.00 8350.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

104 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

105 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

106 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

108 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

109 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 5.000 69.00 345.000

1.23.5 6 pin 15/16 A socket outlet Each 5.000 137.00 685.000

Supplying and fixing two module stepped type electronic fan

110 1.25 regulator on the existing modular plate switch box including Each 40.000 369.00 14760.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

111 1.29 phenolic laminated sheet cover in front including providing and Each 5.000 358.00 1790.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

112 1.30 phenolic laminated sheet cover in front including providing and Each 5.000 488.00 2440.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

113 1.33 junction box/ wooden block including connections etc. as Each 40.000 87.00 3480.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

116 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 5.000 599.00 2995.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

123 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 50.000 706.00 35300.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

127 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

131 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 40.000 339.00 13560.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

132 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

135 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 40.000 2837.50 113500.000

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

137 MR standard item with copper wiring, control gears and lamps as required as per the Each 8.000 2812.00 22496.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Electrical Works Total : 6,72,173.00 2,68,821.00

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF BOYS DORMITORY FOR 320 nos OF STUDENTS - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

G. DSR 2022 Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

111 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

113 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 50.000 334.00 16700.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

115 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

116 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

117 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

119 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

120 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 10.000 69.00 690.000

Supplying and fixing two module stepped type electronic fan

121 1.25 regulator on the existing modular plate switch box including Each 80.000 369.00 29520.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

122 1.29 phenolic laminated sheet cover in front including providing and Each 10.000 358.00 3580.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

123 1.30 phenolic laminated sheet cover in front including providing and Each 10.000 488.00 4880.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

124 1.33 junction box/ wooden block including connections etc. as Each 80.000 87.00 6960.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

127 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 10.000 599.00 5990.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

134 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 40.000 706.00 28240.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

138 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

142 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 50.000 339.00 16950.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

143 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

146 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 50.000 2837.50 141875.000

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

148 MR standard item with copper wiring, control gears and lamps as required as per the Each 8.000 2812.00 22496.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Electrical Works Total : 10,06,907.00 3,58,596.00

Digitally signed by JAYA

COST ABSTRACT :- REPAIR WORK OF GIRLS DORMITORY FOR 240 nos OF STUDENTS - JNV, BALESORE, ODISHA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

H. DSR 2022 Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

111 1.8 conduit, with piano type switch, phenolic laminated sheet,

suitable size M.S. box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way piano type switch,

phenolic laminated sheet, suitable size MS box and earthing the

point with 1.5 sq.mm. FRLS PVC insulated copper conductor

single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

113 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm Mtr 40.000 334.00 13360.000

FRLS PVC insulated copper conductor single core cable for loop

earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single

core cable in surface/ recessed medium class PVC conduit as

Rewiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

115 1.15 single core cable and 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable as earth wire in existing surface/

recessed steel/PVC conduit including dismantling as required.

Rewiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable and 1.5 sq.mm

116 1.16 FRLS PVC insulated copper conductor single core cable as earth Point 10.000 894.00 8940.000

wire in existing surface/ recessed steel/PVC conduit including

dismantling as required.

Supplying and drawing following sizes of FRLS PVC insulated

117 1.17 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing metal box of following sizes (nominal size)

119 1.22 on surface or in recess with suitable size of phenolic laminated

sheet cover in front including painting etc. as required.

Supplying and fixing following piano type switch/ socket on the

120 1.23 existing switch box/ cover including connections etc. as

1.23.4 3 pin 5/6 A socket outlet Each 8.000 69.00 552.000

1.23.5 6 pin 15/16 A socket outlet Each 8.000 137.00 1096.000

Supplying and fixing two module stepped type electronic fan

121 1.25 regulator on the existing modular plate switch box including Each 70.000 369.00 25830.000

connections but excluding modular plate etc. as required.

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Supplying and fixing metal box of 150mm X 75mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

122 1.29 phenolic laminated sheet cover in front including providing and Each 10.000 358.00 3580.000

fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch,

connections, painting etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm

deep (nominal size) on surface or in recess with suitable size of

123 1.30 phenolic laminated sheet cover in front including providing and Each 10.000 488.00 4880.000

fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type

switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing

124 1.33 junction box/ wooden block including connections etc. as Each 80.000 87.00 6960.000

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

127 2.3 complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.2 Single pole and neutral Each 10.000 599.00 5990.000

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150

mm, made of mild steel, at least 2 mm thick, and vitreous

enameled white on both sides, and with inscription in single red

colour on front side as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

134 5.11 pipe from earth electrode including connection with G.I. nut, Mtr 40.000 706.00 28240.000

bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode

with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth

electrode including connection with G.I. thimble excavation and

re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing as required.

Providing, laying and fixing following dia G.I. pipe (medium

138 14.13 class) in ground complete with G.I. fittings including trenching

(75 cm deep)and re-filling etc as required

Digitally signed by JAYA

Amount on DSR -

Sl No DSR 2023 Item Description Units Total Qty Rate (In Rs) Non DSR (In

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact

fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly

on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper

conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including

wiring the down rods of standard length (upto 30 cm) with 1.5

142 1.45 sq. mm FRLS PVC insulated, copper conductor, single core cable, Each 30.000 339.00 10170.000

including providing and fixing phenolic laminated sheet cover

on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including

143 1.50 making good the damage, connection, testing, commissioning

etc. as required.

Supply of pre-wired 1x36 watt electronic fluorescent fitting complete with all accessories

Supply of pre-wired 2x18 watt CFL Square type mirror optics fitting complete with all

accessories and tube etc

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps

146 MR & regulator etc. ISI with 5 star marked & energy efficient complete as required. 1200 mm Each 40.000 2837.50 113500.000

Supply of AC 230/250 volts, 50 HZ exhaust fan including providing nuts, bolts, mounting

FRL same and other accessories etc. complete

300 mm sweep 900 rpm

Supply of 2x12 watt LED Single CWG Pipe Glass Wall Bracket fixtures complete as per

148 MR standard item with copper wiring, control gears and lamps as required as per the Each 6.000 2812.00 16872.000

satandard catalouge item..(Such as Decon Cat. No. L05AAM - 2x 12 or Equivalent).

Electrical Works Total : 9,32,130.00 2,76,822.00

Digitally signed by JAYA