SPL REPAIR TO C WELL IN ZONE 2A AND PROVN OF TRAINING SHED AT FORMATION TRAINING AREA AT TALBEHAT MIL STN

Amount

Taking down cement or cement lime plaster on brick wall/concrete surface, ceiling incl. raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L 15mm thick plaster in CM 1:3 on fair surfaces of walls finished even and smooth w/o using extra cement in mixed with liquid water proofing compound as per manufacturer instructions (at any depth of well) including necessary scaffolding complete all as specified and directed.

M&L for 15mm thick external plastering in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth w/o using extra cement complete all as specified and directed.

M & L preparation new plastered surfaces of walls and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of white wash complete all as specified and directed

M & L complete removal of existing treatment of old wall and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

Supply only liquid water proofing compound.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping or chamfered on edges in any description or like other wks. including necessary form work complete all as specified and directed by Engr-in-charge.

M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate 50mm thick as in plinth protection finished fair even laid in alternate bays n.exc 2m in length all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site as specified and directed.

S&F Framed/ Unframed work as in doors or gates of angle or other section with gusset plates, rails, braces, also small article for old gates etc complete, all small articles including drilled for fixing of steel sheeting or other covering etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete all as specified and directed.

S&F MS sheet1.25 mm plain black sheet cut to size, holes punched including rounded headed screws, clout nails or rivets and fixed to steel framing with plain 40mm lap joints with riveted or welded seams including bending or as in covering to door shutters complete all as specified and directed.

M&L for MS framed work such as square guard bar any size conforming to Fe 290-0 or Fe 330-0 welded to ventilator/window or opening portion complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or girth & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified & directed.

M&L for preparation of old steel painted surface of any description and applying two coat of synthetic enamelled paint complete all as specified and as directed by Engr-in-Charge

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm completed all as specified & directed.

Cutting holes into or through brick wall built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates confirming to Fe 410W(Gde E-250 quality A)complete all as specified & directed.

Dismantling Asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F for Pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified & directed.

Demolition of cement concrete (unreinforced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone as in foundation /sub base of floor, filling and mass concrete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:3:6) Type C-2 100 mm thick using 40 graded stone aggregate as in sub base of floor complete all as specified and directed..

M&L PCC 1:2:4 type B-1using 20mm stone crushed aggregate 100 mm thick as in floor complete all as specified and directed.

M & L for PCC inter locking tiles, coloured, reflective type/rubber moulded, conforming to IS-15658-2006 of 60mm thick,M-35 grade of approved quality, laid over and incl 50 mm thick sand cushion vibrated with mechanical vibrator complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth and removing surplus soil to a distance n.exc 50 m in soft/loose soil complete all as specified and directed.

M&L for PCC 1:3:6 , type C-2, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates confirming to Fe 410W (Gde E-250 quality A)complete all as specified and directed.

S&F for Post steel work in tubular pipe in suitable dia complete all as specified and directed.

S&F pre-painted Galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws complete all as specified and directed.

S&F MS plate or angle, channel, square cut or notched with riveted, bolted, or welded attachment complete all as specified and directed.

M/S R.S.BUNDELA & SONS

HARNAM SINGH ANIL SINGH