PROVN OF SINGLE LIVING ACCN FOR NFS NODE AT DANAPUR CANTT

Surface Dressing n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out Soft / Loose Soil complete all as specified and directed.

M &L for ATT Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M & L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Boring holes 3m deep in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50m (dia of pile 300mm) complete all as specified and directed.

Excavation in trenches in soft/ loose soil not exc 1.5m wide and not exc 1.5m deep for foundation, pier holes etc n. exc 10sqm on plan and getting out complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in columns, pillars, posts, struts etc complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in coping, beams, cantilevers, bressummers, Lintels over 1.5m span etc complete all as specified and directed.

M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggreagate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns raft, beam sides and soffits (if any) of foundations & plinth beams and similar wk etc rough finished surface of concrete complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers, columns stachions flat with rough finished surface of concrete complete all as specified and directed.

Form work to sides of concrete floor or roof beams, beam haunchings, bressummers, lintels, cantilevers, shelves including supports overhangs etc also sprays between floor beams, etc on flat with rough finished surfaces of concrete complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cracking, bending, spirally for hopping for columns hookings ends and binding with and incl mild steel wire (annealed) not less the 0.9mm dia or securing with clips complete all as specified and directed.

Same as per item No 16 above but 5 mm dia and over in stirrups, spacers and binders complete.

M&L for old size Brick work with sub- class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L 15mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extra cement) complete.

M&L 15mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and directed.

Supply only water proofing compound (liquid), ISI marked.

M&L hard core of broken bricks of gauge n exc 63mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L 100 mm thick plain cement concrete (1:3:6), type C-2 using 40 mm graded stone aggregate as in sub base including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L 25 mm thick plain cement concrete (1:2:4), type B-0, using 12.50 mm graded stone aggregate as in floors including finishing the surface rough & even for receiving kota/tiles ccomplete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm and not exceeding 0.18 sqm in floors etc over and including over 15mm thick screed bed in CM 1:6 set & jointed in neat cement slurry and pointed with white cement mixed with pigments to match the shade of tiles complete all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match with shade of tiles over and including over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 10mm thick dark shade vitrified ceramic tiles, exceeding 0.36 sqm but not exceeding 0.42 sqm as on vertical surfaces skirtings, dados etc, over and including 10 mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles complete all as specified and directed.

M&L for glazed ceramics coloured tiles of size 450x300x7mm thick on vertical surfaces such as skirting/dados/wall, etc over and including 10mm thick rendering in cement mortar (1:4) set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles complete all as specified and directed.

Returning filling in inclunding spreading levelling watering well raming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material exc 50m but n exc 150m and depositing where directed at a level n exc 1.5m above the starting point.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete all as specified and directed.

S & F 30 mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats.

S & F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with omogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165.

S & F pressed steel frame of size 105 X 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc. complete all as specified and directed.

S & F pressed steel frame of size 125 X 60 mm and 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

M & L for plain cement concrete 1:3:6 type C-0 (using 12.50 mm graded stone aggregate), as in back filling of pressed steel frames and similar work including necessary form work as required complete all as specified and directed.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long.

S&F mild steel, 150 mm long ordinary helical door spring incl roller and roller plate complete all as specified and directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F floor door stopper 140 mm overall length of cover plate of aluminium alloy body and tongue, anodised. With hard drawn spring, fixed in floor complete all as specified and directed.

S&F small fitings of 2nd class hard wood door, window stops and the like not exc 200 cum each including MS butt hinges, medium weight, cold rolled 50mm long complete all as specified and directed.

S&F GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified and directed.

S&F 18/19 mm thick Block baords, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, including teak wood lipping, 6 mm thick on sides complete for cupboard shutter and incl shelves complete all as specified and directed.

S&F 100 mm long hasp & staple aluminium anodised wire type, incl bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F mild steel conduit curtain rod with PVC coating fancy type curtain rod 25 mm dia of any colour as approved complete all as specified and directed.

Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors complete all as specified and directed.

S&F of CPVC 20 mm Outer dia Brass Elbow complete.

S&F of CPVC 20 mm Outer dia Brass Elbow (3/4 x 1/2) complete.

S&F of CPVC 20 mm Outer dia Brass Tee complete.

S&F of CPVC 20 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 25 mm Outer dia male Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 20 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/FBTA) complete.

S&F of CPVC 25 mm Outer dia female Brass threaded Adoptor (3/4 x 1/2) (MTA/MBTA) complete.

S&F of CPVC 20 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 25 mm Outer dia Brass Tank Adoptor complete.

S&F of CPVC 20 mm Outer dia Brass Union complete.

S&F of CPVC 25 mm Outer dia Brass Union complete.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in chromium plated central hole basin mixer single lever without popup waste system with 450 mm long braided hoses complete all as specified and directed.

S&F of wash basin vitrous china (flat back and angle back Type) size 630X450mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe.

S & F Vitreous china wash down water closet pan (pedestal pattern) cascade type of size 365 X 635 X 770 mm coloured with cistern (with twin flush fittings) complete including seat cover and fixing of flushing cistern, brackets, flushing pipe etc complete all as specified and directed.

S&F white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F in 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S & F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in PVC connection 15mm dia size and 600 mm long with 2 Nos check nuts its washers complete all as specified and directed.

S&F cabinet mirror, box type of size 19" x 21" of colour as approved fixed to wall complete.

S&F 5.5 mm thick looking mirror ordinary quality glass in square n exc 0.5 Sqm grinding polishing and rounding off edge , drilling hole in glass fixed to wall with brass screws, cups and washers complete as specified and directed.

S&F in bib tap 15 mm bore,cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F CP brass tubular towel rail 20 mm dia 60 cm long.

S&F in angle cock 15 mm bore cast copper alloy fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railling 60cm long all as speicified.

S&F in of stainless steel soap dish, of standard size and shape complete.

S&F in chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed.

S&F PVC (SWR) 'P' trap for 110 mm dia etc complete.

S&F chromium plated toilet paper holder with flap complete all as specified and directed.

M&L Machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine including rubbing and polishing over and including 20 mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors/ trenches complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors/trenches complete.

S&F PVC (SWR) pipes 50mm bore single socketed in any length with rubber ring joints laid in floors/trenches complete.

S&F clamp made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete.

M/L PVC(SWR) bend of 110mm dia of any radius etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

M/L PVC(SWR) Single T of 110mm dia etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 75 mm dia

S&F PVC (SWR) vent cowl 75mm bore

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I of 1000 Ltr capacity complete all as specified and directed.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete.

M/L PVC(SWR) bend of 75mm dia of any radius etc complete all as specified and directed

M&L 50 mm thick PCC 1:3:6 type C-1 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/ kerbs/ sunken slab etc complete all as specified and directed.

M&L 10 mm thick rendering on roof surfaces / concrete surface in CM 1:4 complete all as specified and directed.

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm

Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

Applying two coats of black bituminous paint including preparation complete

M & L for concrete bed in P.C.C. 1:4:8 type D2 (using 40mm graded stone aggregated) to drain pipes including packing under and haunching against the sides of the pipes after laying and testing for the following dia of pipes.

100 mm dia.

150 mm dia.

M & L for salt glazed stoneware (SGSW) drain pipes grade 'A' laid in trenches and jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed for the following internal dia of pipes.

100 mm dia.

150 mm dia.

M & L for plain cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates in foundation for manholes, Septic tanks and drains complete all as specified and directed

M & L for plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate), as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregates) as in bedding of drain etc all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregates) as in drain benching etc. surface finished even and fair all as specified and directed.

M&L for PCC 1:2:4 type B-1(using 20mm graded stone aggregates) as in coping of drains including necessary formwork etc all as specified and directed.

M&L for 15mm thick cement plaster on brick surfaces of drian in cement mortar 1:4 surface finished even and smooth without using extra cement all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc all as specified and directed.

M&L for pre-cast RCC slabs as in manhole covers in 1:2:4 type B1 using 20 mm graded stone aggregate, set in cement mortar (1:4) incl use and waste of form work complete all as speciied and directed.

M&L for Chequered cement concrete tiles (in any shade) 20cmx20cmx25mm /30x30x25 mm thick, set, jointed and pointed with grey cement and pigment in floors over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L poviding and laying 60mm thick factory made chamfered edge cement concrete paver block M-35 grade with approved colour, design & pattern as in footpath, parks, lawmn, drive, ways or light traffic parking etc of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and patterns, finishing and sweeping extra sand all as specified.

M&L 300mm dia Reinforced concrete pipes, class NP2, laid and jointed on concrete bed including PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) packing under and haunching against the side of pipe after they are laid and tested complete with collars all as specified and directed.

M & L Providing and laying at ground level factory made kerb stone of M-25 grade plain cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete as required all as specified and directed.

Form work of rough finished flat surface to edges of concrete flats, breaks in floors openings in concrete walls ,floor and roofs and sides of RCC/PCC bands in walls ,horizontal or slopping ,and similar work all exc 20 cm wide (where RCC/PCC band in walls, spanning and opening ) complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for cutting holes in brick wall built in cement mortar for inserting holdfast , walls exc half brick n.exc one brick thick and making good dismantled portion in cement mortar 1:3 complete all as specified and directed.

S&F steel windows with side hung shutters including hinges with MS handles and tower bolts hold fast complete without glazing bar & wire gauzed bars dovetailed or welded with one shop coat of zinc chromate primer complete all as specified.

S&F steel ventilators with top hung shutters including hinges, steel peg stay hold fast including taking down existing ventilators complete all as specified and directed.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

S & F solid PVC door frame of size 75 mm x 50 mm made out of choice colour PVC with wood grain solid complete all as specified and directed.

S&F 200mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed

S&F 100mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed

S&F 100 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S& F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick figured glass pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each panel etc complete all as specified and directed.

S&F continuous (Piano) hinges 40 mm width of flaps, mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F 40 mm dia cup board knobs, fixed with nut, screw and washer of mild steel bright finish complete all as spfd & directed

S&F of ball catches with 8 mm dia steel ball and brass body and striking plate incl letting in complete all as specified and directed.

M & L for 2nd class Hard wood as in plain fillets, square, rectangular, traingular in section clean sawn secured with nails or brads of sectional area exc 13 & not exc 25 Sq cm complete all as specified and directed

S&F 2 lever brass cupboard lock grade-I size 65 mm etc complete all as specified and directed.

S&F 100 mm dia extruded brass handle, fabricated type polished fixed to board complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/ / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Same as item No. 141 here-in-before but one 3 pin, 5 Amp socket out let on independent board complete all as specified and directed.

Same as item No. 141 here-in before but 3pin ,5 Amp socket out let on the same board with other switch complete all as specified and directed.

Same as item No. 141 above but for one bell/buzzer point controlled by one bell push single pole one way .

Same as item No. 141 above but for one 6 pin 15/16 Amps socket outlet point on an independent board with cables of size 2.50 Sqmm.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 4.0 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 4 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including 6.0 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of exsting sub main wiring complete all as specified and directed. NOTE : Two runs of 6 Sqmm and one run of 6.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

M&L for sub main wiring with PVC insulated 1100V grade FRLS single core multi stranded copper conductor cable of size 2x4 sqmm + 1x2.5sqmm as earth continuity cable passing through and including 25/20mm dia PVC conceal conduit all as specified and directed by Engr-in-Charge. Note - Two runs of 4sqmm including one run of 2.5 sqmm including PVC conduit shall be measured as unit length.

S & F for switch piano, flush type, 5 amps, single pole , one way , 230 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for bell, ding dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F ceiling rose single phase , PVC poly carbonate,insulated body three terminals ISI marked complete all as specified and directed.

S&F sheet metal enclosure for 4 way TPN DB double door 415 Volt with 200 amp rated bus bar complete with suitable for 1 x 63Amp TPN as incomer and MCB SPN as outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of 4 poles and current carrying capacity 63 Amp in the DB complete with connection testing and commissioning complete all as specified and directed.

S& F for sheet metal enclousre factory made for MCB DB's SPN, 12 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

S&F MCB SP 240 Volt 6 TO 40 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F MCB SPN 40 to 60 Amp 30mA for earth leakage. Over load and short circuit protection ISI marked complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserveciable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode.)

S&F stepped type electronic fan regulator flush type AC 230 volt suitable for BLDC ceiling fan complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC integrated type including driver, Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser , 4 ft,2000lm,voltage protection range 140V -270 V,NW 4000K , ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix Decorative, wall mounting, champagne fixture with plastic body including 9 W LED lamp B22 base wall light complete all as specified and directed.

Supply and fixing LED lights fitting 1x 10W, 220V,AC integrated type including driver, Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser , 2 ft ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified.

S & F Building security/street LED light fitting 35 watt IP-65 protection pressure diecast alluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 m long complete fixed in and including GI pipe medium grade 40 mm fixed to pole complete all as specified and directed.

Supply, fixing and testing of ceiling fan 1200 mm sweep, heavy duty, single phase, AC, 230 Volts, 50Hz, BEE 5 star rating, ISI marked complete with down rod, canopy, blades, BLDC motor etc and connecting up complete including complete connection from ceiling rose to fan including writing of MES Number with synthetic enamel paint complete all as specified and as directed including taking down old unsv one and deposit in MES store for BER.

Supply and fix wall fan high speed 400 mm electric corded 2100 RPM air delivery 105 CMM ,input voltage 240 V sturdy base and thermal overload protectionfor safety and durability complete all as specified and directed.

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed.

Supply and fix 7 W round white LED Panel light ceiling/recessed mounted luminous efficiency 75 Lm/W IP 20 including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply, laying , jointing and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

M & L clean dry river sand in trenches/ducts for cushioning to cable, 8 cm in depth before laying the cable and 15 cm in depth after laying the cable complete all as specified. Note:- Punned thickness shall be measured and paid.

M & L for old size sub class ‘B’ bricks, laid in trenches as cable covers / protection complete all as specified and directed.

Supply and laying galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc in trenches complete all as specified and as directed of following sizes :-.

25 mm (1”) dia.

20 mm (3/4”) dia.

S & F for Gun metal gate valve with iron wheel head screwed both ends ISI marked fixed to GI pipe complete all as specified and directed of following sizes :-

25 mm (1”) dia

20 mm (3/4”) dia.

M & L for Cutting existing GI/CI water mains 80 mm dia in position for insertion of tee, branch line etc to new water connection complete all as specified and directed.

Please Enable Macros to View BoQ information