Construction of proposed washroom for general public, litigants at the space where Max Lab proposed to be opened in the premises of Hon ble Punjab and Haryana High Court Building, Sector 1, UT Chandigarh

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. .2.8

All kinds of Soil. .2.8.1

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : .2.10

All kinds of soil .2.10.1

Pipes, cables etc, not exceeding 80 mm dia. .2.10.1.1

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia .2.10.1.2

Providing and laying in position cement concrete of specified grade excludingthe cost of centering and shuttering - All work up to plinth level : .4.1

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) .4.1.3

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) .4.1.10

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). .5.3

Centering and shuttering including strutting, propping etc. and removal of form for all heights : .5.9

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Shelves (Cast in situ) -- Wash Basin Shelves .5.9.4

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. .5.22A

Thermo-Mechanically Treated bars of grade Fe-500D or more. .5.22.A6

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: .6.1

Half brick work with common burnt clay F.P.S (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor V level. .6.13

Cement mortar 1:4 (1 cement : 4 coarse sand) : DSR 6.13.2 .6.13.2

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry .6.15

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. .8.2

Granite stone slab of colour black, Cherry/Ruby red .8.2.2

Area of slab over 0.50 sqm .8.2.2.2

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including .8.5

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Size 300mm x 600mm) .8.31

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: .9.21

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws .9.21.1

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). .9.23

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. .9.83

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: .9.95

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : .9.96

Providing and fixing aluminium tower bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. .9.97

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with essary screws etc. complete : .9.100

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: .10.14

Profile B .10.14.1

Fixing with adjustable lugs with split end tail to no's jamb .10.14.1.1

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 15 mm (± 1 mm) thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. .11.56

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. .11.56.1

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. .13.80

Distermpering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 gram/litre, of approved brand and manufacture including applying additional coats wherever required to achieve even shade and colouur .13.81

Old work (one or more coats) .13.81.1

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in- harge. .15.2

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) .15.2.1

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- harge. .15.7

In Cement Motar .15.7.4

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead .15.12

: Of area 3 sq. metres and below .15.12.1

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. .15.23

For thickness of tiles 10 mm to 25 mm .15.23.1

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. .15.56

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. .15.60

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. .17.16A

Providing and fixing C.P Brass 32mm size bottle trap of approved quality and make and aas per the direacction of Engineer-in-charge. .17.22A

Providing and Fixing 600x450mm superior quality mirror with bevelled edge (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. .17.31

Providing and fixing soil, waste and vent pipes : .17.35

100 mm dia .17.35.1

Centrifugally cast (spun) iron socket & spigot (S & S) pipe as per IS:3989 .17.35.1.2

75mm diameter .17.35.2

Centrifugally cast (spun) iron socket & spigot (S & S) pipe as per IS:3989 .17.35.2.2

Providing and fixing plain bend of required degree. .17.39

100 mm dia .17.39.1

Sand cast iron S&S as per IS:3989 .17.39.1.2

Providing and fixing heel rest sanitary bend .17.40

100 mm dia .17.40.1

Sand cast iron S&S as per IS:3989 .17.40.1.2

Providing and fixing collar : .17.57

Sand cast iron S&S pipe as per IS: 3989 .17.57.1.2

Sand cast iron S&S pipe as per IS: 3989 .17.57.2.2

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : .17.58

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors .17.60

100 mm inlet and 75 mm outlet .17.60.2

Sand Cast Iron S&S as per IS- 3989 .17.60.2.1

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including cutting chases and making good the walls etc. .18.10

15 mm dia nominal bore .18.10.1

20 mm dia nominal bore .18.10.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : .18.17

20 dia nominal bore .18.17.1A

Providing and fixing uplasticised PVC connection pipe with brass unions : .18.21

45 cm length .18.21.2

15 mm nominal bore .18.21.2.1

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : .18.46

15 mm dia nominal bore .18.46.1

20 mm dia nominal bore .18.46.2

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. .18.48

Providing and fixing c.p Brass bib cock of approved quality conforming to IS:8931 .18.49

15 mm nominal bore .18.49.1

Providing and fixing C.P. Brass extension nipple (size 15mm x 50mm) of approved make and quality as per direction of Engineer-in-charge. .18.53A

Cutting holes up to 30x30 cm in walls including making good the same: .18.76

With common burnt clay F.P.S. (non modular) bricks .18.76.1

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. .18.77

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: .19.4

100x100mm size P Type .19.4.1

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .19.4.1.1

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: .19.30

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : .19.30.3

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 .19.30.3.1

Providing and fixing in position wall mounted european style white vitreous EWC of Hindware and other necessary fitting required to make the item functional complete in all respect and to the entire satisfaction of Engineer in Charge .NSR

Providing and fixing concealed flushing cistern alongwith push plate, the necessary fixing required to make the item well functional complete as per allotment. .NSR

Providing and fixing C.P. angle valve with wall flange of Make Jaquar Model Continental or equivalent model of approved makes .NSR

Providing and fixing 1 mm thick stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete in all respect as per Makes approved by EIC. .NSR

Providing and fixing of C.P. towel ring of Make Jaquar Model CON or equivalent model of any other approved make. .NSR

Providing and fixing soap dispensor 200ml with C.P. screw complete in all respect as per Makes approved by EIC. .NSR

Providing and fixing Pressmatic pillar cock Auto closing system complete in all respect s per entire satisfaction of EIC and make as approved by Enggineer-in-charge: (Make Jaquar Model PRS-031) .NSR

P/F of under counter wash basin with C.I. brackets without pillar taps including 32mm CP brass waste of standard pattren ,including painting of fittings and brackets cutting and making good the walls whereever require make as approved by EIC Cera (Ocean) .NSR

Providing and fixing CP Handshower (Health Faucet) with 1 metre long Easy Flex tube in Chrome finish & Wall Hook & flow restrictor of 6.0 LPM at 3 bar pressure complete in all respect as per Makes approved by EIC. .NSR

Providing and fixing C.P. finish Toilet paper holder of Jaquar AKP-35751P/Hindware F450027CP/Cera F 5001109 complete in all respects and to the entire satisfaction of the Architect and EIC. .NSR

Providing and fixing of Sensor Concealed type flush valve of urinal complete set with installation box & Control valve having 9V transformer make Jaquar Model SNR-STL-51077E or equivalent Model of approved make list. .NSR

Providing and fixing of Urinal (Back Inlet) with fixing accessories, Size: 385x325x635 mm complete in all respect as per Makes Jaquar Model URS-WHT-13253N or equivalent Model of approved Make list. .NSR

Providing and fixing of frosted glass urinal partition Hindware make of size 900x450x8mm complete with stainless steel cleats, fixing arrangement complete in all respect as per entire satisfaction of EIC and make as approved by Engineer - in - charge .NSR

Providing and fixing C.P. brass finish concealed stop cock of Jaquare solo /Cera Gayle /Hindware Flora series with the necessary fixing required to make the item well functional all complete in all respects and to the entire satisfaction of the Architect & Engineer in charge .NSR

Dismantling of GI Pipe up to 20 mm dia in open or in chase including stacking the dismantled pipe and disposal of malba complete. .NSR

Providing and fixing of MS Angle and IRC Jali Frame including the cost of MS Angle 40X40X5mm thick IRC Jali 30 mm x 30 mm. complete with cutting, welding, fixing with CC 1:2:4 painting complete in all respect to the entire satisfaction of EIC complete in all respect. .NSR

Please Enable Macros to View BoQ information