PROVISION OF DEFICIENT OFFICE ACCN CUM OPEN SHED AT BSO AT NDA KHADAKWASLA

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth;for foundation,etc. or for shafts,wells,cesspits, manholes, pier holes,etc.not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth;for foundation,etc. or for shafts,wells,cesspits, manholes, pier holes, laying cables etc.not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in hard / dence soil complete all as specified and directed.

M&L broken Brick bats deposited spread and leveled in layers n.exc 15cm thick water and rolled/rammed true surfaces (for rising of path level) complete all as specified and directed

M&L for PCC in foundation, filling and mass concrete in M7.5 (Nominal Mix) using 40mm nominal size graded crushed stone aggregate complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in foundations, including rafts,footings,foundation beams,plinth beams;bases for columns,etc; basement slabs,under-reamed piles and mass concrete comlpete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in columns, pillars,piers,posts and struts etc. complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in beams, cantilevers, bressumers,lintels over 1.5m span etc.complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in chajjas comlpete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs,landings, balconies, canopies, deck slabs and in shelves and the like comlpete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, landings and similar work not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for formwork to sides of concrete foundation, footings, base of coloumns, raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels. Cantilevers, shelves including supports, overhangs, etc also splays between floor and beam etc for rough finished flat surfaces of cocrete complete all as specified and as directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surfaces of concrete complete.

M&L for formwork to sides of pillars, posts, struts, piers, coloumns and stanchions for rough finished flat surfaces of concrete complete.

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan,exceeding 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan,to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate all as in floors, finished even and smooth without using extra cement all as specified and as directed.

M&L for plastering 10mm thick on fair faces of brick work or concrete surfaces (on vertical surface) in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for plastering 15mm thick (in two coats of 10mm and 5mm thick) on fair faces of brick work or concrete surface ( on vertical surfaces) in cement mortar 1:4 with integral water proofing compound finished even and fair complete all as specified and as directed. Note Water proofing compound will be measured and paid for separate complete all as specified and as directed.

M&L for 75mm thick, plain cement concrete 1:3:6, type C-2 (40mm graded stone aggregate) finished surface even and fair as in plinth protection all as specified and as directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63mm, deposited, spread, & leveled in layers n.exc 15cm thick watered & rammed to a true surface complete all as specified and as directed.

M&L for cement concrete 1:4:8, Type D-2 using 40mm nominal size graded crushed stone aggregate 75mm thick in sub base for laying tiles, pavings etc all as specified and as directed

M&L for plastering 5mm thick on fair faces of brick work or concrete surface on ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick damp proof course in cement concrete M15 (Nominal mix) using 12.5mm nominal size graded crushed stone aggregate mixed with integral water proofing compound to horizontal or vertical surfaces including necessary form works complete all as specified and as directed. Note :- Water proofing compound will be measured and paid for separately.

S&F pressed steel door frames conforming to IS 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness size 125mm x 60mm profile B, one or more rebate including hinges, mortar guards, lock strike plate, shock absorbers complete all as specified and as directed.

S&F solid PVC door frames of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawaingcomplete all as specified and as directed.

S&F 30mm thick factory made solid panel PVC door shutter as per IS 15931 : 2012 with 19 gauge thickness mild steel tube and tapering 20mm in 45 degree angle on both sides forming styles and on the inner side to form top and bottom rail and on both sides to form lock rail complete all as specified and as directed.

S&F flush door shutter 30mm thick solid core of block boards construction, MR grade, commercial type with stiles rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1) : 1999 both sides face panel of plywood as per IS 710 : 2010 internally lipped complete all as specified and as directed

S&F 2nd class hardwood Glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F hot rolled medium and high tensile structural steel of grade E-165 as per IS 15911:2010 as in clamps, hold fasts, wall ties, hooks for hanging fansn plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S&F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 250mm long anodized to a bright natural, mat finish complete all as specified and as directed.

S&F 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified & as directed.

S&F 100mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341:1992 complete all as specified and as directed.

S & F for aluminum powder coated (poder coated of required colour) three track sliding windows frame top & sides of size 92 x 31.75 x 1.50mm (section No 20831) bottom of size 92 x 31.72 x 1.50mm (Soction of 20832) and shutter top & bottom of size 40 x 18 x 1.55 (section 20738) and lock side shutter frame of size 40 x 15 x 1.45mm (Section 20737) with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc complete all as specified and as directed.

M & L for Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and as directed.

S&F sheet glass ordinary quality 5.5mm thick glazed with oil putty or fixed with beads in square not exc 0.5Sqm in each pane complete all as specified and as directed.

M & L for preparing new wood and wood based surfaces of any description over 10 cm width or girth,not otherwise described applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M & L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over 3mm thick wall care putty and one coat of alkali resistant primer complete all as specified and as directed.

M & L for preparation of plastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

S & F vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed.

S&F PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flush pipe, brackets complete all as specified and as directed.

S&F for Wash basins white, vitreous China, flat back, size 580x450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed to wall complete all as specified and as directed.

S & F Vitreous China urinals,half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe (excluding flushing cistern, flush pipe and waste pipe) Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) including all fitting complete all as specified and as directed.

S&F sinks made of stainless steel 01 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M & L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

S & F flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm connected to PVC waste fittings complete all as specified and as directed.

S&F for 32mm waste coupling of PTMT (half or full threaded) (minimum weight 40mm-60 gms) complete all as specified and as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S & F towel rail 600 mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastics cleats, minimum weight 190 gms complete all as specified and as directed.

S&F for PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified & directed.

S&F for 15mm bore Tubes, 'midium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F fancy type 15mm dia Bib taps cast copper alloy, chromium plated screwed down to iron pipe or for brass ferrule & fixed complete all as specified & directed.

S&F fancy type15mm dia pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipe & fixed complete all as specified & directed.

S&F 15mm bore dia stop valves / angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed.

M&L for providing two way bib cock with wall falange copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup complete all as specified and as directed.

S&F for hand shower (health faucet) with 8 mm dia, 1 mtr long flexible tube and wall hook complete all as specified and as directed..

S&F for 20mm bore Tubes, 'midium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors or laid in trenches complete all as specified and as directed.

S & F for 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete all as specified and as directed.

S&F for rotational moulded polyethylene water storage tanks of 500 ltr capacity,(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I complete all as specified and as directed.

S&F for 20 mm nominal size brass float valve, high pressure, with polythene float and flynut, screwed for iron pipe and fixed complete all as specified and as directed.

S&F for PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 75 mm, complete all as specified and as directed.

S & F for 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and as directed.

S & F for 100mm cast-iron sanitary connection bend (92½0), with arms 380 to 450mm, excluding joint complete all as specified and as directed.

S & F for 100mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Bends, any radius fixed complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F PVC vent cowl, 75 mm dia complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Bends, any radius fixed complete all as specified and as directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M & L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M & L for mild steel TMT bars 6 mm to 8 mm dia, in stirrups cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for Glazed Ceramic Matt Finish/Anti Skid Tile size of each tile 300x300mm as per IS 15622:2017 20mm over 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Glazed Ceramic Wall Tile of Size of each tiles 600x300mm, thickness 8-10 mm as per IS 15622:2017 of Group Blll with water absorption not more than 10% over 10mm thick cement plaster CM 1:4 complete all as specified and as directed.

M&L for Vitrified Tiles of Polish Finish of thickness 8-10mm, size of each tile 600x600mm Ultra Charge/Double Charge/Multi Charge of Light Shade as per IS 15622:2017 of Group Bla with water absorption less than 0.08% over 20mm screed bed in CM 1:6 complete all as specified and as directed.

M&L for Applying two coats of distemper oil bound including preparation of newly plastered surfaces on ceilings and complete all as specified and as directed.

Supply only approved intrgral water proofing compound complete all as specified and directed.

M&L water proofing treatment on floor/roof etc comrising with the following operation complete all as specified and directed (a) M&L 15mm thick plastering in cement mortar 1:4 finished even and smooth. (b) Preparing & cleaning of fully dried cement concrete. (c) Applying one coat of cold bituminious primer to the plastered surfaces @ 0.3liters per sqm conforming to IS-3384-1986. (d) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.50 kg per sqm reinforced with polyester non woven fabric (weighing not less than 150gms/sqm) shall be applied over bituminious primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100mm on transverse direction and 75mm in longitudinal direction. (e) One coat of aluminium paint over the APP based membrane @ 0.11 kg/sqm.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm of soft loose soil complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Wind ties etc grade Fe-410-W Quality A complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes complete all as specified and as directed.

M&L for Cutting chases for concealed conduit wiring, pinning in and making good to surface where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., cutting not exc 10 cm girth including 3 mm thick wall care putty on wall, making surface matching to adjacent surface complete all as specified and directed.

M&L for concealed sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm, 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed. Note: Two runs of 04 Sqmm cable with 01run of 4 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed sub main wiring with Two single core PVC insulated FRLS cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including PVC conduit medium grade with all fitting & other accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed. Note:Two runs of 6 Sqmm cable with 01 run of 6 Sqmm earth wire along with PVC conduit medium grade shall be measured as one RM

M&L for concealed point wiring in and including new PVC conduit medium grade with the help of multi-stranded unsheathed FRLSH copper cable 1.5 sqmm 650/1100V conforming IS:3419 -1988 adhereing to colour code including earth wire of the size 1.5 Sqmm green colored with modular steel or cast iron terminal boxes and modular cover plates as required at site including making good the distrubed surfaces and matching it with existing surface for the following :- (a) One light /fan point controlled by one switch one way

(b) One 3 pin 5 Amps socket outlet point on independent board

(c) One 3 pin 5 Amps socket outlet point on Same board

M&L concealed point wiring with 4 sq mm copper conductor FRLSH (multistrand) PVC insulated ISI marked unseathed cable in and including PVC conduit not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 4 sq mm copper conductor as earth wire to common earth dolly complete all as specified and directed.

S&F modular switch 1 way 10 A 1 module complete all as specified and directed. Make: Crabtree cat part no ACWSXXW101 or equivalent make as mentioned at makes list in PS

S&F Modular socket 6 A 2/3 Pin 2 module complete all as specified and directed. Make: Crabtree cat part no ACWKPXW063 or equivalent make as mentioned at makes list in PS

S&F modular switch 1 way 16 A 1 with indicator module all as specified and directed. Make: Crabtree Cat Part No ACWSXIW161 or equivalent make as mentioned at makes list in PS

S&F Modular socket 6 A/16A 2/3 Pin 2 module complete all as specified and directed. Make: Crabtree Cat Part No ACWKCXW163 or equivalent make as mentioned at makes list in PS

S&F modular BLDC fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep complete all as specified and directed. Make: Crabtree cat part no ACWRFXW006 or equivalent make as mentioned at makes list in PS

S&F ModularType C 2.1 A USB Charger all as specified and directed by Engr-in-charge. Make: Crabtree cat part no ACWKRXG002 or equivalent make as mentioned at makes list in PS

S & F RJ-11 telephone socket with transparent shutter 1 module alongwith flush metal box 2 module and front cover plate 2 module complete all as specified and directed. Make: Crabtree cat part no ACWKRXW112 or equivalent make as mentioned at makes list in PS

S &F for LAN RJ-45 Jack With Cat 6 socket UTP Cat with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed. Make: Crabtree cat part no ACWKRWW451 or equivalent make as mentioned at makes list in PS

S &F for TV socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed. Make: Crabtree cat part no ACWKTOG001 or equivalent make as mentioned at makes list in PS

S&F ceiling rose, 3 terminals / PVC / Polycarbonate, isolated body complete all as specified and directed..

M&L for concealed Telephone cables for indoor applications up to 10 pair pvc insulated copper conductor wire including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm concealed in wall, roof, etc, with all connected fittings from tag block to telephone outlet complete as required at site including making good surfaces and matching with the existing surface complete all as specified and directed.

M&L for concealed including termination of RG-11 cable for TV including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm concealed in wall, roof, etc, with all connected fittings complete as required at site including making good surfaces and matching with the existing surface complete all as specified and directed. Make-Havells WHOJTTKARG11 or equivalent make as mentioned at makes list in PS

M&L for concealed of Cat6-4 pair,23 AWG, UTP Cable, 305m waith cross member pair spearator including heavy duty non metalic PVC conduit, ISI marked, not less than 20 mm dia of thickness 1.8 mm concealed in wall, roof, etc, with all connected fittings complete as required at site including making good surfaces and matching with the existing surface complete all as specified and directed. Make-Havells WHLJTTERCAT6 or equivalent make as mentioned at makes list in PS

S&F 18/20watt,230V surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser and integrated electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified and directed. Make- Luker LT5M20 / Havells ENDURALINEARNEOBS20WLED865SPCWH / Bajaj BCLAB 20W WH LED P or equivalent make as mentioned at makes list in PS

S&F 12 watt,230V surface and wall mounted LED Mirror Light including connecting up with twin core twisted flexible copper condctor cable from ceiling rosecomplete all as specified and directed. Make- Luker LMCL 12 or equivalent make as mentioned at makes list in PS

S&F 20 watt,230V surface and wall mounted LED Smart batten, Smart extruded aluminium housing with higher efficaay.Microwave sensor to save more energy.Reduces the light intensity by 70% during non occupancy including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified and directed. Make- Bajaj BCLAB 20W LED P S or equivalent make as mentioned at makes list in PS

S&F LED building security light fiitting 30 W, IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having TOP opening seperate driver compartment complete all as specified and directed. Make- Luker LSTE-30/ Havells ENDURACITYLITEPLAT PLUSSL30WLED757SASYBOPC / Wipro LR02-331-XXX-57-XX or equivalent make as mentioned at makes list in PS

S&F decorative suspended LED Light with high efficiency providing soft-light and glare free symmetrical illumination including suspension kit E 27 holder with lamp including connecting up with twin core twisted flexible copper cable to fitting complete all as specified and directed.

S&F Infrared Presence Surface Mount Sensor for light fittings including connecting up with twin core twisted flexible copper cable to switch and fitting complete all as specified and directed.

Supply and fixing ceiling fan complete with blades, down rods and other accessories, 230 V, 1200 mm sweep with Minimum air delivery of 210 CMM BEE Five star rated with brushless direct current motor (BLDC), white/Ivory in colour complete all as specified and directed. Make:Crompton /Havells/Orient/Atomberg

S&F of high speed wall mounted fan of sweep 400 mm,,Full copper motor (BLDC),auto thermal overload protection,compact style and powder coated gurads & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories complete all as specified and directed. Make:Crompton /Havells/Orient/Atomberg

S&F of Plastic ventilation Energy Saving Exhaust Fan with BLDC Motor fan of 200 mm sweep inclduing replacing the plywood as per the site requirement complete all as specified and directed. Make:Crompton /Havells/Orient/Atomberg

S&F factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified and directed . Note:MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F MCCB with rating of 100 Amps, 415 Volts 3 pole with 16 kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu). MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and directed.

S&F MCB DB 12 way SPN Double door sheet metal enclosure factory made suitable for MCB DB's 240 volts,concealed in wall complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete all as specified and directed. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoingcomplete all as specified and directed.

S&F MCB DP 40-63 Amps C Curve working on 240 volts, 50 HZ,10 KA complete all as specified and directed.

S&F sheet metal enclosures with single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc complete all as specified and directed.

Supply and Laying including testing and commissioning LT UG Power cable, XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables 4 Core 25 Sqmm (heavy duty) 1100 Volts grade with multi-stranded aluminium conductor including termination with LT Panel/Feeder Pillar with galvanised or Cadmium plated high tensile nuts, bolts and washers etc including Sheddling /clamping on any type of wall with suitable size of GI Clamps, nuts, bolts & washers etc complete all as specified and directed

Supply and laying 50 mm outer dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e coupler, Tee, elbow clamp for cable protection complete all as specified and directed.

S&F GI tubing 'light grade' 50 mm dia ISI marked with all fittings laid in trenches and fixed on pole by flat iron clamps, nut, bolt, washer of suitable size complete all as specified and directed.

Excavation in trenches in soft / Hard Rock/dense soil/loose soil not exceeding 1.5 metre wide and not exc 1.5 metre in depth and getting out for taking out / laying of GI / CI pipe line and making bottom surfaces of excavation leveled and to a gradient complete all as specified and directed.

Supply and laying in trenches / on ground GI tubing 'Medium grade' of 25 mm bore with all fittings like Tee,socket,elbow etc complete all as specified and directed. Note: excavation of earth work shall be measured and paid seperately

Supply and fix in Bronze Gate Valves (Hexagonal type) 25mm with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

Supply and fix in Bronze Gate Valves (Hexagonal type) 20mm with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

Cutting existing cast iron pipes 80mm dia in position for insertion of new tees (80x80x25)/ branch including short nipple for branch connections complete all as specified and directed.

M & Labour for Valve Pit Chember of size 750x750x500 mm ( Internal Dimension) with block massioary including all necessary excavation and earth work in any type of soil, returning filling and disposal of spoil to a distance .exc 50m and depositing where directed, PCC in foundation of the mix (1:4:8) type D-2 ( Using 40mm graded stone cruched stone aggregate) brick mesonary 15 mm thick plaster work in CM 1:4 over all internal and external wall with white wash of both surface and MS sheet cover of suitable thickness for with hinges, equal angle iron frame and necessary locking arrangement painting of synthetic Enamel paint over coat of red oxide primer on MS Plate complete all as specified and directed.

M&L Boring of holes under road, pavements, hard standing by Trenchless Technology using Ultra Sounding technique and necessary machine including HDPE pipe of upto 150mm dia suitable for 0.4mpa working pressurecomplete all as specified and directed for passing GI Pipe of bore size 50/25/15mm. Note : Damages to any existing Electric/ Tele communication cable, Water/Sewage pipeline if any, will be repaired immediately by the Contractor and cost for the repair is deemed to be included in quoted rate.

SUN Enterprises

M/s. Shige Construction