CA NO. CWE/CHM-63/2020-21 NAME OF WORK MANUFACTURE AND SUPPLY OF FURNITURE FOR KLP ACCN OF ENGR REGT AT CHANDIMANDIR (PHASE-I) AND AGAINST CERTAIN SANCTIONED WORK UNDER GE CHANDIMANDIR

Amount

PART I - WOODEN FURNITURE

Chair Dining with Cushion (DRG NO FD/MAP-II/04) All wood work shall be of 1st class hard wood (Teak). (b) Seat shall be 75MM thick foam of 40 density covered with good quality tapestry cloth (cost of cloth not less than Rs 350/- per meter) as approved by GE over 12MM thick commercial plywood as per IS- 303. (c) Nylon buffers of appropriate size shall be screwed to the bottom of each leg. (d) All exposed surfaces of timber and plywood shall be frech polished. (e) All joint fixingg shall be done in accordance with standard workmanship and specification and all as shown on drawing NO FD/MAP/E6/10 complete all as specified and directed. Note 1 to 30 :- Drawings for the same is also available in GE Chandimandir.

Chair For Card Table (DRG NO FD-353) As per drawing and approved by GE/Engineer-in-Charge.

Chair D'Man (DRG NO FD-204)- As per drawing and as approved by GE/Engineer-in-Charge.

Desk Stand Lecture (DRG NO FD-125) DIMENSION :Over all size shall be 970mm wide and 1220mm high. DESCRIPTION: Two upright of mild steel rectangular tube of 75mmx25mm of 1202mm high shall be provided in rear side and shall be 635mm apart. The two upright shall be joinded with bottom, middle and top rails with 75mmx50mm mild steel tube of wal thickness 1.6mm. The two sides rails at bottom fixed at 125mm from bottom shall be 430mm long 75mmx50mm mild steel tube of wall thickness 1.6mm and shall form the part of bottom rails and join the long side of bottom rail of size 785mm long, . All edges of pre-laminated particle board remained exposed shall be covered with teak wood edging as per the size of board edging. FINISH : All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces and all wooden surfaces shall be melamine polish with lacquer finish as approved by Engr-in-Charge.Rest all as per drgs.

DESK (DRG NO FD-107M) All as shown on drawing. Overall size shall be 1270mm long. 530Mm wide and 840mm high. Steel frame shall be of 1270mmx430mmx 810mm. Legs shall be four in numbers and shall be made in inverted U-shape and shall be made of 25mm dia. Mild steel tube of wall thickness 1.6mm with front height as 760mm and rear height of legs shall be 810mm. Two short stiffeners 380 long joining legs in short side at 100 mm from bottom of legs and sheall be provided of 25mm dia mild steel tube of 1.6mm wall thickness. A long stiffener joining the short stiffeners in the middle shall be provided with 1220mm long and 25mm dia tube of wall thickness 1.6mm. Two 1220mm long bearers shall be provided for the support of desk and shall be provided at 615mm from bottom of legs Desk shall be made of 18mm thick pre-laminated particle board of natural teak veneer shade made as box with front side open and top sloping with PVC edging on front side irrespective of what is shown on drawing. The size of desk shall be 1220mmx530mm and 170mm high in front and 220mm high at back. The back of desk shall be of 6mm thick MDF board or 6mm thick pre-laminated particle board with teak veneer shade as directed by Engineer-in-charge with PVC edging alround irrespective of what is shown on drawing . All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint over a coat of primer with spray machine after preparation of surfaces.

Hat Stand with Mirror (DRG NO FD-361) DIMENSION:Overall size shall be 1330 mm long, 710mm high. DESCRIPTION:The inner frame shall be of 50mmx20mm teak wood battens six in nos .The back and front of frame shall be covered with 6mm thick commercial ply.The edges of the frame shall be covered with 6mmx35mm teak wood edging fixed alround the frame with headless nails and adhesive.Six brass pegs 120mm long shall be fixed over the wooden membrane with brass screws as shown in drg.5mm thick looking mirror of (saint gobian,Modiguard/Atul) shall be provided as shown on drg with beading alround . Mild steel key plate shall be provided at both top corners of the hat stand. FINISH: All teak wood surfaces shall be given high gloss French polish with lacquer finish. All steel surfaces shall be painted with two coats of enamel paint over a coat of primer. Rest all as per drgs.

Table 600 x 600 x760mm (DRG NO FD-293) As per drawing and as approved by GE/Engr-in-Charge.

Chair Easy with Detachable Cushion (DRG NO FD-358) DIMENSION:Overall size shall be 510mm long, 545mm wide and 710mm high. DESCRIPTION: Timber shall be seasoned teak wood(MP) Ist Quality. Front legs shall be of size 70mmx25mm in section 520 mm high and rear legs shall be of section 70 mm x25 mm in section slanting 185 mm horizontally in the height of 490 mm . The front and rear rails shall be provided below the seat joining front legs and rear legs .Front legs shall be 510 mm apart and rear legs shall be 480 mm apart . The top of front legs shall have wooden arms rest of 65 mm x25 mm in section and 610 mm madfe to shape as shown on drg. The legs shall be joined by side rails 70 mm x 25 mm in section teak wood. The bottom frame of seat shall be of 55 mm x 20 mm in section over which 3/4 mm thick plywood commercial shall be fixed. 75 mm thick foam cushion of 32 density with upholster with leathersied rexine of approved shade and texture as directed by BSO/ GE.Hard rubber/ PVC shoes of 25 mm dia 25 mm high shall be provided to the bottom of legs with screws. FINISH:All wooden surfaces shall be polished with two coats of melamine polish with spray machine after preparation of surfaces.

TV Trolly (DRG NO FD/E6/MAP/04) DIMENSION:-Overall size shall be 650mm long x 500mm wide and 750mm high. DESCRIPTION:-The sides,back,shelf and front openable shutters shall be of prelaminated MDF board of 18/19mm thick with 4mm thick teak wood beading alround the edges of the MDF board fixed with headless nails and adhesive.The front shutters shall be of 5.5 mm thick glass shutter with magnetic catcher.Brass handle and door catchers shall also be provided to the TV trolley as described on drg..The pull out drawers shall be provided with two telescopic channel.The top of the trolley shall be of prelaminated MDF board of 18/19mm thick with 4mm thick teak wood beading alround the edges of the MDF board fixed with headless nails and adhesive .50mm dia swivel type castors heavy duty twin wheel 4 in numbers shall be provided at base .rest all as per drg. FINISH:- All wooden surfaces shall be french polished in high gloss finish.

Pointer 1525mm Large (DRG NO FD-1041 & 71) As per drawing no and approved by GE/Engineer-in-Charge.

Stool dressing with cushion (DRG NO FD/E6/MAP/14) (a) The plywood 12mm thick wherever shown on drawing shall be 18/19 MM thick decorative type with Prelaminated partical board finish on one side. (b) The seat shall be removable type made of 75MM thick synthetic foam of 40 density covered with tapestry cloth of shade and texture as approved by GE. The tepestry cloth shall be coating not less than Rs 350/- per runing meter. (c) All expoased edges of particle board shall be provided with 4MM thick teak wood edging unless otherwise shown on drawing. (d) All exposed surfaces of wood and wood based material shall be French polished. (e) Rest all as shown on drawing and as directed by GE/ Engr -in-charge.

Teapoy Wooden (DRG NO FD-278) All as shown on drg. Overall size of peg table shall be 600mm long, 450mm wide 540mm high. All wood shall be of Ist class teak wood. Top of table shall be made out of prelaminated particle board 18mm thick exterior grade and 4mm thick teak wood beading shall be provided all round the table irrespective of what is shown on drg and all as per drg No FD-278 complete all as specified and directed.

Table Bed Side (MAP) DRG NO FD/E6/MAP/15(R) (i) Pipe shall be 18mm MS square pipe (18 gauge) black powder coated. (ii) Top and back portion above top of Table bed side shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination) as specified here-in-before. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in top and pull out tray. Back of table bed side shall be of 6mm thick commercial plywood as per IS-303. (iii) Sides and back of drawers shall be provided with 12 mm thick commercial plywood as per IS-303. Bottom of drawer shall be provided with 6 mm thick commercial plywood. (iv) Movement of Pull out tray and drawers shall be made on teak wood runners. One aluminum anodized handle shall be provided to each drawer. (v) Stoppers shall be 2nd class Hard wood (Sal/benteak/Bijasal/Hollock). (vi) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vii) All exposed surfaces of timber and plywood shall be French polished. (viii) All joints fixing shall be done in accordance with standard workmanship and specifications. (ix) Rest all as shown on drawing.

PART II - STEEL FURNITURE

Trestle Store Room Steel (DRG NO FD-1043) DIMENSION:Overall size shall be 2440mm long, 600mm wide a 300mm high. DESCRIPTION:Two long angle iron 40mmx40mmx6mm of mild steel 1980mm long shall be provided 520mm apart at bottom connected with 50mmx3mm iron bracing, four in numbers, and equally spaced with 50mmx 50mmx 6mm iron.Rest all as per drg. FINISH: All Steel and iron work surfaces shall be painted with two coats of enamel paint over a coat of primer with spray machine after preparation of steel surfaces on exposed to view when placed in position.

Table Cook House Large (DRG NO FD-1019) DIMENSION: Over all size shall be of 900x540x840mm. DESCRIPTION :All steel used in the manufacturing of frame structure shall be of 25mm square MS with wall thickness 1.6mm .Top shall be of 25mm thick marble stone slab duly finished and rounded edges.6mm dia MS lugs (04 in nos) shall be provided at top of upper rails through welding for the support of stone top.Hard rubber toes shall also be provided to bottom of each leg.All Dimensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table D'Man Steel (DRG NO FD-1016) DIMENSION:-Over all size shall be of 1650x 800x 900mm. DESCRIPTION:-The top shall be of prelaminated MDF board of 18/19mm thick with 4mm thick teak wood beading alround the edges of the top fixed with headless nails and adhesive. Timber shall be seasoned teak wood Ist Quality knot free.The Sliding/adjustable top shall also be provided as shown in drg with suitable arrangment of height adjustment providing tee highes and 300mm long steel stays .The frame of the table shall be of 25mm square tube of wall thickness 1.6mm.The drawers shall be provided with lock and chrome plated handle.PVC shoes shall also be provided to the bottom of each leg.All steel surface shall be painted with silver hammer paint after preparation of surfaces. All Dimensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg. FINISH:-All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine. Rest all as per drg.

ALMIRAH STEEL (MEDIUM) (DRG NO FD-1032) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1mm MS plain black sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. Six lever brass lock shall be provided as per Godrej pattern. (iv) One steel chrominium plated handle shall be provided to the drawer. (v) Locker of the almirah shall be provided with locking arrangement operated with handle as per Godrej pattern. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamelled paint (silver grey colour) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (xiii) Rest all as shown on drawing.

Almirah Large Steel (DRG No FD-1031) (i) Steel Almirah (body, shutter, drawer, locker, vertical partitions and shelves) shall be made out of 1 mm thick mild steel sheet all as shown on drawings. (ii) All joints/welding/fixing shall be done all as shown on drawings and with standard workmanship. (iii) Almirah shall be provided with three way locking device as per ‘Godrej’ pattern .The handle shall be made out of steel chrominium plated as per ‘Godrej’ pattern. 4 lever brass lock 65 mm size shall be provided as per Godrej pattern, of make GODREJ, LINK, HARRISON. (iv) Almirah shall be provided with three numbers adjustable shelves with four compartments (v) One steel chrominium plated handle shall be provided to the drawer. (vi) All steel surfaces internally and externally shall be painted with two coats of synthetic enamel paint (olive green) with spray gun over a coat of zinc chromate steel primer. (vii) The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint. (viii) Rest all as shown on drawing.

BED MAP STEEL (DRG NO FD/E6/MAP/08(R)) (i) Bed hard shall be manufactured all as per details shown in the drawing. All dimensions, shape and size shall be followed as per drawing. (ii) All square and rectangular MS pipes shall be of thickness 18 gauge. (iii) Top of bed shall be of 12mm thick commercial plywood (unpolished) as per IS-303 (iv) Head board and foot board shall be of 18mm thick Prelaminated particle board (both side decorative finish shade as approved by GE ) as specified here-in- before, screwed to MS strip all as per details shown in drawing. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in Head board and foot board . (v) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vi) All exposed steel surfaces shall be painted with two coats of synthetic enamel olive green paint over a coat of zinc chromate steel primer. The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (vii) Rest all as shown on drawing.

BOOK CASE STEEL( DRG NO FD-1028) Item to be fabricated as per drg. Overall size shall be 840mm long, 310mm wide and 1675mm, cold rolled, cold annealed MS sheet 1mm thick to be used for channel base, top, sides, back, bottom, front and shelves. The book case shall be provided with four compartments of equal size. The shutters of each compartment shall be open towards top and slide into the depth of the book case. Two steel handles of 100mm shall be provided to each shutter of the compartment. The locking device shall be provided to each compartment. All joints and welding, fixting shall be done in accordance with standard workmanship. rest all as shown on drawing.

Charpaoy GI Pipe with 12mm thick Ply wood top (DRG NO FD/E6/MAP-II/01) Overall size shall be 1980mm long, 900mm wide and 440mm high. Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mmx25mmx16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer. Rest all as per drg.

Chair Verandah : (DRG NO FD/MAP/06/01) DIMENSION :- The overall size of the chair shall be 455mm wide 455mm deep and 940mm high. DESCRIPTION :- The frame of the chair shall be of 19mm dia MS tube of wall thickness 1.6mm duly powder coated 70 microns by 7 tank process and oven dried . The seat and back of the chair shall be of PVC 4mm of weight not less than 1.85 kgs and grooves 90x10mm ten in nos on seat and back. One stiffener 19mm dia MS tube shall be provided in between the front legs as shown in drg. An additional support in seat and back shall be provided at centre between the seat and back duly welded for rest of PVC seat irrespective of what is shown on drg. Rubber shoes of best quality shall be provided to each end of legs.Rest all as per drg. FINISH:-The frame of the chair shall be powder coated 70 microns by 7 tank process and oven dried in white.

Rack Three tiers (Steel) (DRG NO FD-106) Over all size shall be 915 mm long, 610mm wide and 990mm high. (The width is variable and shall be considered for procurement as per requirment of users. However this specification has been considered with 610mm width. Four vertical angle iron of 40mmx40mmx4mm shall be provided at four corners. Top, bottom, sides, back and shelves shall be 1mmthick mild steel sheet. The bottom sheet shall be at 100mm from bottom of legs. Two shelves equally spaced too form three compartments shall be provided of 1mm thick mild steel sheet. Four 75mmx75mmx3mm flat iron cut to shape oto form angle brackets shall be provided on front side as shown on drawing. All steel surfaces exposed to view when placed in position shall be painted with two coats of enamel paint over a coat of primer after preparation of steel surfaces. Painting shall be done with spray machine.

Stool Steel 305mmx305mmx510mm(DRG NO FD-81M) DIMENSION:Over all size shall be of 305mmx305mm x510mm. DESCRIPTION:18 Gauge MS sheet for top and angular frame shall be provided.The top shall be made out of 1mm MS sheet.All Dimensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg. FINISH:Paint synthetic enamel colour olive green 1st class shall be used two coats over a coat of primer (internal and external).

Table Steel 900mmx600mmx760mm (DRG NO FD-1008) DIMENSION;Overall size shall be 900mmx600mmx 760mm. DESCRIPTION:Steel frame shall be of 800mmx500 x742mm.Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm.Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm top rails on long and short sides. Two short stiffeners joining legs in short sides at 100mm from bottom of legs shall be provided with 25mm square mild steel tube of wall thickness 1.6mm .One long stiffener shall be provided in the middle of short stiffener joining short stiffeners with 25mm square mild steel tube of wall thickness 1.6mm at 100mm from bottom of legs. A drawer on left side of table near top stiffener shall be provided of size 350mmx130mm and 500mm deep with locking arrangement and recessed handle. Mild steel sheet used for drawers shall be of 1mm thickness.Top of table shall be of 18 mm thick pre-laminated particle board of walnut shade and 4mm teak wood edging al -round the top of table. PVC/Hard rubber toes shall be provided to the bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Table Steel 900mmx900mmx760mm W/o Drawers (DRG NO FD-1009) DIMENSION :Overall size shall be 900mlong,900mm wide and 760mm high. DESCRIPTION: Steel frame shall be of 800 mm X800mm X742mm . Four legs shall be of 25mm square mild steel tube of wall thickness 1.6mm. Legs shall be joined together with the top rails of 25mm square mild steel tube of thickness 1.6mm. Top of the table shall be of 18mm thick pre-laminated MDF board with 4mm teak wood edging all round the top of table. Hard rubber/PVC toes shall be provided to bottom of legs. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

Chair Writing Map (DRG NO FD/E6/MAP/12) (a) All work shall be of Standard class. All dimensions shape and size shall be followed. (b) Rest all as shown on drawing.

Rack shoe steel (DRG NO FD/E6/MAP/02(R) As per drawing and as approved by GE.

PART - III TRADE PATTERN FURNITURE

Board Notice 6'x4' Make : Alkosign Model No ASB or of equivalent Make as approved by GE.

BATH MAT PVC (FD/MAP/E6/07) (i) All PVC work shall be of standard class PVC. All dimensions shape and size shall be followed as per drg. (ii) Hard rubber shoe shall be provided to the bottom of each leg. (iv) Rest all as shown on drawing No FD/MAP/07 complete all as specified and directed. (iii) PVC Bath Mat shall be of make: Blow plast/Neel Kamal/Supreme/Cello/Polyset/Brite/syntex.

Chair Visitor Cushioned Make Godrej, Model No PCH-7003 or of equivalent Make as approved by GE.

Black board with Easel (size of board 1200 x 1500) Size of stand shall be 1800 mm at bottom and 1200 mm at top in trape zoidal shape. Legs of stand shall be of teak wood and shall be of two numbers of 1830mm long and 75mmx25mm in section. Five holes for pins shall be provided on at 100mm spacing .Bottom stiffener 650mm long , 75mmx25mm in section shall be provided at 460mm from bottom . Intermediate Stiffener shall be 355mm long and 75mmx25mmin section shall be 300mm long and 75mm x25mm in section. Iron strap 40mmx3mm, made to Shape so that 65mmx19mm in section "T" can smoothly slide into it. Horizontal bar of tee shall be 900mm long , 65mmx19mm in section and tee bar shall be of 1065mm long.65mmx19mm in section shall be provided with six holes for inserting pins Make -Alkosign Art No IW BS /4L 120180 or equivalent Make as approved by GE

Chair Office Steel Cushioned with Arms. Make:- Godrej Model No 5002T or of equivalent Make as approved by GE.

Chair Computer W/O Arms. Make :- Godrej Model No 7045 or of equivalent Make as approved by GE.

Chair Revolving Executive. Size : Width 77CM, Depth 77CM, Height 113.5-122.5 CM, seat height 49.9-58.9 CM. Make: Godrej Model No BRAVO HIGH BACK or of equivalent Make as approved by GE.

Conference Table for 25 Pers. Make Godrej U shaped, Model Encarta table height 750mm, width 1350mm or of equivalent Make as approved by GE.

Chair Steel Padded with Arms (Spl Pattern) Make Godrej Model Office 1018 or of equivalent Make as approved by GE.

Cabinet Filling. Filling Cabinet vertical 4 drawers (1320Hx470Wx620D) of Make Godrej Model No FN1232079-S-PM-5458 or of equivalent Make as approved by GE.

Drugget 3.00m x2.00m (Spl Pattern) As per TP and approved by GE/Engineer-in-Charge.

Chair Witing with Writing Pad. Make Godrej Model CH 18 C with desklet or of equivalent Make as approved by GE.

Display Board 900x1200mm (Spl Pattern) Make:- Alkosign Model No ASB 90120 or of equivalent Make as approved by GE.

Form with Back (Chair Steel Type- 3 No.) Make Godrej Model Nano Perch with Arms or of equivalent Make as approved by GE.

Form w/o Back (Chair Steel Type- 3 No.) Make Godrej Model Nano Perch with out Arms or of equivalent Make as approved by GE.

Receptical PVC (DRG NO FD/E6/MAP/13) (a) Recepticle shall be of covered plastic container of 75 ltr capacity made with thick polymer plastic alongwith lid and handles. Recepticle shall be of bright colours ie. Red,Green,Blue etc. (b) Recepticle shall be of make: Blow plast/Neel Kamal/ Supreme/ Cello/Polyset, as approved by GE.

Sofa set 3 Seater. Make Godrej Model Parto sketch FN1502458-S-5458 or of equivalent Make as approved by GE.

Mobile Storage Unit Steel Large. Make Godrej Model Personal Locker 6 Door PLU or of equivalent Make as approved by GE.

Table office Clk Steel (Spl Pattern) Make Godrej Model T-8 or of equivalent Make as approved by GE.

Table Dining 6 Pers (Spl Pattern) Make Godrej Jack or of equivalent Make as approved by GE.

PEG TABLE (TP) Make Godrej Model Glaze Sketch FN 1502458-S-PM-5458 or of equivalent Make as approved by GE.

Table Office Officer Steel (Spl Pattern) Make Godrej Model T-104 or of equivalent Make as approved by GE.

Table computer. Make Godrej Model Stylo or of equivalent Make as approved by GE.

Daya Nand Jindal

agarwal and company

Jiwan Singh AND Associates