REPAIRS TO WOODEN AND STEEL FURNITURE RECANNING OF CHAIRS AND POLISHING OF WOODEN FURNITURE AND PAINTING OF STEEL FURNITURE AT AF STN DEOLALI UNDER GE AF OJHAR

Amount

WOODEN FURNITURE Removing the unserviceable/worn out components without damaging the serviceable components, supply and fix new components all as given below. The new components shall be made of 1st class hard wood (Indian Teak wood) as shown on respective drgs and also to match with the existing components, including sanding, rubbing and polishing to new component provided.1 (a) BED NEWAR/BED HARD WITH PLY TOP (i) Foot board

(ii) Head board

(iii) Long Rail

(iv) Short Rail

(vi) Stiffener

(vii) Removing of old damaged/unserviceable top from bed hard and replacing the top with 12mm thick plywood make Assam Power/Kit Ply/Eco Board all as specified and directed by Engr-in-Charge.

(viii) S&F Steel bent clamp for corner made from flat iron of size 40 mm x 5 mm and painted with two coat of synthetic enemel paint over a coat of red oxide primer.

Taking out the unserviceable components without damaging the serviceable components, supply and fix new components made of Teak wood as per drawing and also to match with the existing components including sanding, rubbing and polishing and applying one coat of French polish to new component or complete table after repairs 1 (b) Table 900x600mm w/o drawer (i) Leg

(ii) Top rail short

(iii) Top rail long

(iv) Stiffener

(v) Side stiffener

1 (c) Table writing (i) Leg

(ii) Leg of cupboard of table

(iii) Top rail long

(iv) Short Rail

(v) Stiffener Long

(vi) Side stiffener

(vii) Drawer complete

(viii) Shutter for cupboard

(ix) Side for cupboard

(x) Removing of old damaged/ unserviceable MS hinge from table writing and replacing the same of size 50mm fixed with suitable screws to table.

(xi) Removing of old damaged/unserviceable knob from table writing and replacing new knob of best quality fixed with suitable size of screw to table.

1(d) Table 900X900mm (i) Leg

(ii) Top rail

1 (e) Table dining 6 persons (i) Leg

(ii) Top rail short

(iii) Top rail long

1 (f) Table 1200 x 900mm (i) Leg

(ii) Top rail short

(iii) Top rail long

1 (g) Table Bed Side (i) Side (LT & RT)

(ii) Shelves

1 (h) Table Centre (i) Leg

(ii) Long rail

(iii) Short Rail

1 (j) Table Peg (i) Leg

(ii) Side rail

1 (k) Teapoy (i) Leg

(ii) Long Rail

(iii) Short Rail

1 (l) Table dining 8 Persons (i) Leg

(ii) Top rail short

(iii) Top rail long

1 (m) Table dressing Gents (i) Mirror

(ii) Drawer complete

1 (n) Table dreesing Ladies i) Leg

(ii) Mirror

(iii) Drawer complete

Removing the unserviceable/worn out components without damaging the other components or structure of chairs, supply and fix new components given below. The new components shall be made of Ist class Hard wood ( Indian Teak wood ) as shown in drawings and also to match with the existing components including sanding, rubbing and applying one coat of French polish to complete chair or only component after repairs 2 (a) CHAIR EASY i) Front Leg

(ii) Rear Leg

(iii) Top and bottom rails of back frame and front rail of seat frame

(iv) Sides and rear rail of seat frame and side rail of back frame

(v) Arm rest

2 (b) CHAIR DINING i) Front Leg

(ii) Rear Leg

(iii) Top rail

(iv) Back rest

(v) Stiffener

2 (c) CHAIR WRITING i) Front Leg

(ii) Rear Leg

(iii) Top rail

(iv) Back rest

(v) Stiffener

(vi) Arm rest

Removing the unserviceable/worn out components without damaging the other components or structure, supply and fix new components given below. The new components shall be made of Ist class Hard wood ( Indian Teak wood ) as shown in drawings and also to match with the existing components including sanding, rubbing and applying one coat of French polish to complete after repairs Side Board 3 (a) Leg

3(b) Long rail

3 (c) Short rail

3 (d) Removing the unserviceable/worn out components without damaging the other components or structure of side board, supply and fix new components given below. The new components shall be made of pre-laminated particle board make ECO BOARD/Kit ply/Assam power as shown in drawings and also to match with the existing components including and applying one coat of French polish to edge beading after repairs(i) Top

(ii) Shutter

(iii) Drawer

3 (e) Removing of old damaged/unserviceable knob from side board and replacing new knob of best quality fixed with suitable size of screw to table and as directed by Engr-in-Charge.

3 (f) Removing of old damaged/unserviceable continuous hinge from side board and replacing new continuous hinge of best quality fixed with suitable size as required of screw and as directed by Engr-in-Charge.

Removing the unserviceable/worn out components without damaging the serviceable components, supply and fix new components all as given below. The new components shall be made of 1st class hard wood (Indian Teak wood) as shown on respective drgs and also to match with the existing components, including sanding rubbing and polishing to complete repairs. 4(a) Stool Dressing (i) Leg

(ii) Side rail

(iii) Stiffener

Removing of old damaged/unserviceable table top from table and replacing the top with 18 mm thick pre-laminated particleboard (one side teak face another white balancing coat) 6 mm thick teak wood beading all around and fixed with suitable size of screws to table frame as per drawing including polishing to teakwood edging all as specified and directed by Engineer-in- Charge 5 (a) Table 900x600mm w/o drawer

5(b) Table Writing

5(c ) Table 1200 x 900 x 760mm

5(d) Table 900x900mm

5(e) Table dining 6 persons

5(f) Table 900x600mm with drawer

5(g) Table Centre

5(h) Table dining 8 persons

5(i) Table Peg

5(j) Teapoy

5(k) Table 600x600mm

Removing the worn out tapestry cloth and lining cloth of both seat & back and S&F new tapestry cloth of quality and texture as approved by the GE and lining cloth duly stiched including chain at one side for seat only. Fitting to frame work as shown on drawing including providing matching buttons to back rest all as shown on drawing and as directed by Engr-in-Charge for the following :- 6(a) Sofa set 3 seater with arms

6(b) Sofa set single seater with arms

Removing the unserviceable/worn out components without damaging the other components or structure, supply and fix new components given below. The new components shall be made of Ist class Hard wood ( Indian Teak wood ) as shown in drawings and also to match with the existing components including sanding rubbing and applying one coat of French polish to complete after repairs Sofa set three/single seater 7(a) Long rail for 3 seater

7(b) Long rail for single seater

7(c) Side/support rail

7(d) Stiffener of bottom and top

8) Removing/taking out of worn out/unserviceable foam cushion & tapesty cloth from seat and back both of sofa set and S&F new foam cushion 100mm thick 40 density make Jyoti/Pooja/Priya duly covered and stiched with superior quality of tapesty cloth, as approved having chain at one side as per existing shape and size, as shown as drawing or as directed by GE/Engr-in-Charge.

9) Removing of old cane and recanning with new indigenous plastic cane not made of recycled plastic as per existing pattern and size of cane for any type of chairs (seat & back), Stool dressing, Bin Soild Linen, Coach sofa etc all as specified and shown in the drg and as directed by Engr-in-Charge a) Chair Easy

b) Chair Dining

c) Chair Writing

d) Stool dressing

10) Material and labour for polishing of furniture including scrapping of rough surface and old worn out polished layer with scrapper /sand paper for smoothing the surface and polishing the same with one coat of approved quality of french polish to glossy finish for the following items of furniture :- 10(a) Chair easy

(b) Chair Dining

(c) Chair Writing

(e) Table Bed side

(f) Table dining 8 persons

(g) Bed Hard/Bed Newar

(h) Table 1200x900x760mm

(k) Sofa set four seater

(l)Sofa set 5 seater in 3 pieces

(m) Table dining 6 pers

(n) Table writing

(o) Table 900x600 with/without drawers

(p) Table peg

(q) Teapoy

(r) Working Table all type

STEEL FURNITURE REPAIRS TO TABLE OFFICE CLERK/OFFICER STEEL 11(a) Taking out existing worn out front/side portion complete of the drawer. Supply & fix new front side/portion complete with lock to the drawer. Removing the dents and bents welding/riveting the damaged portion of the drawer and rectifying portion of the drawer and rectifying other defects to have smooth movement of the drawers all as specified and directed.

12(a) Taking out worn out following components without damaging the other components. Supply the new components made out of 25mm square 16 gauge MS Square tubing and fixing the same by welding to the table office clerk steel in place of removed components :- (i) Legs

(ii) Top rails long

(iii) Top rails short

(iv) Foot rest long stiffners

(v) Stiffeners short

12(b) Taking out worn out following components without damaging the other components. Supply the new components made out of 25mm square 16 gauge MS Square tubing and fixing the same by welding to the table office officer steel in place of removed components :- FD-1003 (I) Legs

(ii) Top rails long

(iii) Top rails short

(iv) Foot rest long stiffners

12(c) Removing dents and bents and carrying out the minor repairs, repairs to locking device complete of the drawers to have smooth movement. Material and labour for preparation of steel surface of table providing high class glossy finish synthetic enamel paint over a coat of red oxide primer wherever required. Providing PVC shoes to the legs:- (i) Table office clerk steel

(ii) Table office officer steel

12(d) Removing of old damaged/unserviceable table top from table steel and replacing the top with 18 mm thick pre-laminated particleboard (one side teak face another white balancing coat) 6 mm thick teak wood beading all around and fixed with suitable size of screws to table frame as per drawing including polishing to teakwood edging all as specified and directed by Engineer-in- Charge (i) Table office clerk steel

(ii) Table office officer steel

12(e) Removing existing unserviceable old locks from table. Supply and fix new lock, made out of steel body Grade I type of 50mm size with six brass levers and with duplicate keys, all and fixed to the steel table with screw, complete all as specified and directed

CHAIR CB STEEL WITH/WITHOUT ARMS 13(a) Taking out the old worn out and unserviceable portion of MS tubular frame of chairs as listed below. M&L for new portion/part duly fabricated to shape and size as shown on drawing to match/fit in the chair and made out of 25mm dia 16 gauge MS tubing. Welding the new fabricated portion/part to the chair frame all as specified and directed. (i) Complete all shape base portion of steel chair frame

(ii) Pair of L shape vertical base portion of steel chair frame

(iii) 25 mm dia 16 gauge 460mm long on tubing support between the seat and back frame of each steel chair frame

(iv) 50 x 25 x 3mm Mild Steel cleats with a hole to hole a screw, four cleats each, to seat and back frame of each steel chair frame to support wooden seat/back wooden frame all as specified and directed

14(a) Removing damaged unserviceable Seat frame from chair CB tubular steel with arm/without arm and back frame from chair CB steel with/without arm supply and fix new seat and back frame complete with suitable size of screw as specified all as per drawing and directed by Engr-in-Charge. (i) Back frame for chair CB tubular steel with arm

(ii) Seat frame for chair CB tubular steel with arm

iii) Arm Rest for chair CB tubular steel with arms

CHAIR VARANDAH 15(a) Removing of old cane and providing new plastic cane white coloured indigenous not made of recycled plastic, as per existing pattern and size for chair verandah after applying one coat of synthetic enamel paint (white colour) on frame complete all as specified, shown on drawing and as directed by Engr-in-Charge.

(b) M&L for spot welding joints of frame of chair varandah as where required

CHAIR VARANDAH (c) Removing of old cane and providing new PVC moulded seat and back white color to the existing frame of chair varandah after applying one coat of synthetic enamel paint white color complete all as specified and directed by Engineer-in-charge.

16(a) CHARPOY GI PIPE WITH NYLON NEWAR Supply and fixing of nylon newar 50 / 55 mm wide virgin quality and re-weaving closely with the charpoy GI frame. Nylon newar shall not be less than 1.50 kg in each charpoy. (Recyle newar shall not be used) all as specified on drawing and as directed by Engineer-in charge.

(b) Removing damaged unserviceable long rail of charpoy GI pipe and replacing with new long rail of 32mm dia medium grade GI pipe with ISI mark duly threaded at both ends (minimum 10 threads for each end) and fixing as per drawing all as specified and directed by Engineer-in-Charge.

(c) Removing damaged unserviceable short rail from Charpoy GI pipe and replacing with the pipes obtained from sl item No 142 above as long rails, but cut to the size duly threaded at both ends (minimum 10 threads for each end) fixing as per drawing, all as specified and directed.

(d) Removing damaged unserviceable GI elbow 3 way 32mm dia from charpoy GI pipe. Supply and fix new GI elbow 3 way 32mm dia medium grade with ISI including GI Check Nut where ever requried fixing as per drawing, all as specified and directed.

REPAIRS TO ALMIRAH LARGE/MEDIUM STEEL:- 17 (a) Removing existing unserviceable old locks from Almirah steel. Supply and fix new lock, made out of steel body Grade I type of 75mm size with six brass levers (Make Aligarh or equivalent as approved by GE) and with duplicate keys, and fixed to the steel Almirah with four screw or as required, complete all as specified and directed

17 (b) Removing existing unserviceable handle from steel Almirah. S & F new steel chromium plated handle of 150mm size all as per Godrej pattern and fixed to steel Almirah with hexagonal nut and steel pin of appropriate size complete all as specified and directed.

17 (c) Taking out existing locking device carrying out all minor repairs, dent and bents to the Almirah Large/Med steel refixing the same to the steel Almirah with providing of new screw or nut and bolt all as specified and directed by Engineer-in-Charge

17 (d) M&L for removing old worn out hinge from Almirah Large/Med Steel and S&F new hinge of best quality and fixed with welding.

17 (e) Removing dents, bents of steel Almirah, welding to broken portion. Rectifying all minor defects and repairs. Material and labour for preparation of steel surface of Almirah (inside & outside surface) including doors shelves and legs. Providing high class glossy finish synthetic enamel paint over a coat of red oxide primer wherever required. All complete specified shown on drawing and directed for following Almirah:- i) Almirah Large Steel with Shelves

(ii) Almirah Med Steel with Shelves

TABLE DINING ORS :- 18(a) Removing of old damaged/unserviceable table top from table dining OR’s FD-165(M) and replacing top with 18mm thick particle board duly covered with aluminium sheet of 22 gauge and fixing with suitable size of screws to table frame including one coat of black synthetic enamel paint as specified all as per drawing and as directed.

18 (b) Taking out worn out component as listed below removing dents/bents welding broken frame. Supply & fixing new component made out of 25mm 16 gauge square tubing to match & fit in place of worn out component of steel frame of Table Dining OR’s. i) Leg Frame complete

(ii) Stiffener Long

M&L for removing/scrapping old worn out paint from the following steel furniture by sand paper and painting with two coats of OG synthetic enamel paint make Asian/Berger over a coat of red oxide primer. Rest all as specified in the drg and as directed by Engr-in-Charge:- 19 (a) Almirah Large steel 1/2 H 1/2 S steel

(b) Almirah steel with mirror 1950x1500x600mm

(c) Book shelf open large med steel

(d) Book case steel

(e) Rack steel adj 6 tier

(f) Rack Pigeon hole steel

(g) Rack Shelf open steel 1000x600x1125mm

(h) Rack side steel with tray

(i) Stool steel 600mm high

(j) Stool Steel 305x305x760mm

(k) Shoe Rack Steel 1500x650x300mm

(l) Stool steel 305x305x510mm

(m) Table Typist Steel 1219x711x762mm

(n) Chair CB Steel with/without arms

(o) Almirah Large Steel with shelves

(p) Almirah Med Steel with shelves

(q) Rack Steel 975x900x500mm

(r) Table office officers steel

(s) Table office clerk steel

CHAIR EXECUTIVE REVOLVING WITH BACK Taking out unserviceable/worn out the following componets of the chair exectutive revolving high back, S&F new components as per existing shape and size to the chair color as approved or as directed by Engr-in-Charge:- 20 (a) Cushioned seat

(b) Cushioned back

(c) PV Handle

(d) Bottom stand (PVC) with caster wheel

(e) Hydraulic pump steel

(f) MS Tilting MS Frame

CHAIR COMPUTER Taking out unserviceable/worn out the following componets of the chair computer, S&F new components as per existing shape and size to the chair color as approved or as directed by Engr-in-Charge:-21 (a) Cushioned seat

(b) Cushioned back

(c) PV Handle

(d) Bottom stand (PVC) with caster wheel

(e) Hydraulic pump steel

(f) MS Tilting MS Frame

CHAIR EXECUTIVE VISTER WITH BACK Taking out unserviceable/worn out the following componets of the chair exectutive Vister S&F new components as per existing shape and size to the chair color as approved or as directed by Engr-in-Charge:- 22(a) Cushioned seat

(b) Cushioned back

(c) PV Handle

Mahesh Traders