Certain B/R maint works, joinery, plumbing, flooring, roof treatment etc in Bn A Md accn under AGE B/R-II, GE Gurdaspur.

Amount

Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L plaster 15mm thick in cm 1:3 in sunken portion of slab using waterproofing compound all as specified and directed Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed.

M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tile complete all as specified.

S&F non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 and dismantling of existing tile floor and screed complete all as specified and directed

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified.

M& L for dark coloured vitrified tiles10 mm thick joint free (square/rectangular) area of each tile n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified.

M & L for Green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and demolition of existing marble complete all as specified and directed.

M&L Granite (of any type) work (table rubbed and polished ) 20 mm thick in steps, jambs, pillars, window cills, cooking platform and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 including demolition of existing work complete all as specified and directed.

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by EIC.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

All as per Srl item No 17 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 16 shall be reused after necessary cleaning of mortar)

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork and welded mesh, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of walls/ roofs etc. finished surface even and fair complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of white putty on plastered surface wall complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed by EIC.

M & L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as directed by Eng-in-charge

S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 completeincl two coat of painting incl taking down old existing window :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, painting with one shop coat of zinc chromate primer incl two coat of painting incl taking down old existing window/ventilator complete all as specified and directed. Note: Glass/ wire cloth shall be measured and paid for separately

S&F anodised aluminium door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. incl taking down old existing complete all as specified.

S&F anodised aluminium window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.75 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl taking down old existing complete all as specified.

S&F anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates including joining cleat for fixing etc.incl taking down old existing and complete all as specified.

S&F 4.8mm thick sheet glass ordinary quality in squares or rectangular not exceeding 0.50sqm in each pane in aluminium door or window shutter complete all as specified and directed.

S&F in repair 4.8mm thick black sheet glass ordinary quality in squares or rectangular not exceeding 0.5 sqm in each pane in aluminium door or window shutter complete all as specified and directed.

M & L for Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers all as specified and directed.

S&F in repairs Mortice lock ,aluminium vertical type size 65mm 2 levers complete all as specidfed and directed.

S&F in repairs Aluminium (Die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F in repair Floor door stopper 140 mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floorcomplete complete all as specified and directed by Engineer-in-Charge.

Repairs, easing & adjusting of shutter without taking down shutters of any description exc 1.00 sqm & nexc 2 sqm each.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed.

Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter for the chowkats) complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame125 X 60mm with single or double rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces and complete all as specified and directed.

S&F pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces complete all as specified and directed.

S&F MS framed work as in door chowkhts or gates of angle or other section with gusset plates,rail, braces,etc and similar work incl primer conform-ing to Fe 410-0 complete.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed.

S&F 2nd class hard wood (Hallock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specified and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

S&F figured glass pin head type glazing with oil puty glass 3mm thick, fixed with oil puty in square n exe 0.5sq m in each pane.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out complete all as specified and directed. .

S&F Aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed.

S&F Aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed.

Supply and fixing in repair cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

M & L for 18/19 mm Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed.

S & F 150 mmHasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

S&F in repair 7-8 mm thick PVC hollow wall panelling consisting of wood grain printed pvc sheet inclusive of solvant cement and fixing at site on PVC frame formed by sticking high density EPS, flame retardent (TF) grade, heavy duty with tipper strip weather proof, water proof, termite proof including all C and U type PVC section with matching of panelling fixing at border of panelling and complete all as specified and directed by Engr-In-Charge.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks ISI marked(cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks nISI marked (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet(pedestal pattern)fixing with bolts ,white colour, incl SS L-type jet spray with 1 m hose pipe, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. incl seat covercomplete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 using 40mm stone aggregate complete all as specified and directed.

S&F in repair vitreous China wash basin, with full pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and 32mm PTMT coupling complete all as specified and directed.

S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) white with grating, waste coupling and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing aroug urinal back in cement, grating and union for discharge pipe incl PTMT waste coupling, waste pipe,brass CP urinal spreader complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1200 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

S & F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 81 above but fixing only (old serviceable pipe re-used).

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 83 above but fixing only including cleaning and new fittings (old serviceable pipe re-used).

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F PVC (SWR) pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S & F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ), ordinary or inverted ) ( or with parallel branches with oval access door complete all as specified and directed.

S & F in repair 75 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ), ordinary or inverted ) ( or with parallel branches with oval access door complete all as specified and directed.

S&F in repair PVC vent cowl of size 110mm.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 100mm dia complete all as specified and directed.

M&L in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm dia complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F in repair Grating doom 100 mm dia with waste hole of PTMT complete all as specified and directed.

S&F in repair Brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge.

M&L for pre cast cement concrete louvers and jali 1:2:4 type B-O (Using 12.5 mm graded aggregate) in jalie 25 mm thick set in cement plaster in CM (1:4) including taking down complete all as specified and directed by Engineer-in-Charge.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified as directed.

75 mm thick, PCC (1:3:6), type C-2 (using 40 mm graded stone aggregate), as in sub base under floor for incr ht. complete all as specified.

Dismantling of existing tiles and M&L for 60 mm thick PCC (M-35) factory made with gray cement and pigment interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand, complete all as specified and as directed by Engr-in-Charge. Note Sand will be paid under relavent item.

M & L coloured Chequered cement concrete tiles with grey cement and no pigment , 30cm x 30cm x 25mm thick,set, jointed and pointed in neat cement slurry in floors in floors over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

S&F machine cut kota stone slab flooring 20-22mm thick over cement screed base 20mm thick in 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing complete all as specified and directed by Engineer-in-Charge.

S&F Gl powder coated frame work for seamless false ceiling, size of grid 605 x 605mm with main tee of size, 32mmx 23.5 mm x1.5mm thick, cross tee of size 25mmx23.5mmx1.28mm and angle of size 23.5mmx23.5mmx1.2mm fixed on wall all powder coated finish on exposed surface of tee and angle, hung from ceiling using 2mm dia GI suspension wires and 'J' bolts , washers, nuts spaced at 1200mm both ways including making niches for fans/light all as specified and as directed.

S&F 12mm thick perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid complete all as specified and directed.

S&F in repair 15 mm brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Demolition of cement concrete (Reinforcment) of any description upto 12 m ht all as specified and directed by Engr-in charge.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs.

S&F 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securing with clips as specified and directed.

M&L for RCC in 1:2:4 type B-1(using 12.5 mm graded stone agg) as in cover slab, chajjas facia, shelves etc and similar work all as spd.

S&F Pre-painted galvantume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls,fixed with self tapping screws including dismantling of old asbestos/corrugated/semicorrugated sheet all as specified and directed.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in Roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (Beam, tee, angle, Coulmn, Gusset Plates, channel, Hollow square/Rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge.

M & L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete etc.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

RATTAN CHAND CHANDAN AND CO (BID ID -3052843)

buta singh and sons (BID ID -3056307)

AVTAR SINGH RAJU (BID ID -3056558)

DEEPAK AND CO (BID ID -3065071)