PROVISION CERTAIN SPECIAL REPAIRS,LBW,REVENUE AND MINOR WORKS IN AGE E/M AND AGE B/R I SUB DIVISION AT MIL STN BIKANER UNDER GE (N) BIKANER.

Amount

Supply, laying and testing Cross linked poly-ethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power under ground cable ( heavy duty) with aluminium conductor, 1100 volts LT grade of cross-sectional area 50 Sqmm 3.5 core laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc supplied, fixed/ laid in repair including commissioning and testing complete all as specified and as directed by Engineer-in-Charge. (Note: :- (i) Necessary excavation and earth work, brick protection, sand cushioning and cover and GI pipe shall be measured and paid for separately.(ii) Road manually cutting/floor cutting/cutting holes etc in wall required for laying /fixing of cable etc shall be made good as per existing site condition. Nothing extra shall be admissible on this account and quoted rate for this item shall be deemed to include for the same)

Ditto All as per Srl item No 01 here in above but size of cable 10 Sqmm 2 core.

Ditto All as per Srl item No 01 here in above but size of cable 10 Sqmm 4 core.

Ditto All as per Srl item No 01 here in above but size of cable 25 Sqmm 4 core.

Ditto All as per Srl item No 01 here in above but size of cable 35 Sqmm 3.5 core.

Ditto All as per Srl item No 01 here in above but size of cable 95 Sqmm 3.5 core.

Supply and erecting steel tubular swaged poles complete with MS base plate, finial taper plug as specified type 410 SP-31 (9.00 mtr long) incliuding painting above planting depth with 2 coats of aluminium anti-corrosive paints of first quality over a coat of red oxide primer includings paintings to pole upto 1.5 m height form top of PCC coping with sythetic enamel paint 02 coats in black and white alternates strip includings numbering in 8 cm height of number with white paint both paint aluminum/sythetic duly approved by the GE complete all as specified.

M&L Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections conforming to Fe-410-0 or Fe-310-0 grade including necessary nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape and size as directed and including applying two coats of aluminium paint (under & finishing coats) over a coat of red oxide zinc chromate primer on exposed steel surfaces after preparation of surfaces, supplied and fixed in repair complete all as specified and as directed by Engineer-in-Charge. (Note: - (i) Sizes & types of members and shape of the cross arms etc shall be as required at site all as directed by the Engineer-in-Charge.(ii) Un-exposed steel surfaces shall be given one coat of red-oxide zinc chromate primer only. Cost of the same is included in unit rate of the item and nothing extra shall be paid on this account.)

M&L Plain cement concrete (1:3:6) type C-2 using 20mm graded stone aggregates for stays and coping of poles above ground level including finishing to exposed concrete surfaces even and fair and provision of form work for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.complete

M&L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregates as in foundation of poles all as specified and as directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 3.0 metre in depth and getting out complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in soft/loose soil including spreading, leveling, watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engineer-in-Charge.

Removing of surplus soil to a distance not exc. 50 meter and depositing where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M&L sand cushioning using clean local tibba fine sand for under ground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified. (Note Punned thickness shall be considered for payment purpose)

Supply and laying burnt bricks sub class 'B' old size for cable protection laid length wise perpendicular to the axis of cable complete all as specified.

Boring of holes 110 mm dia, manually without disturbing the top surface for laying of cables/GI pipes under road , pavement, hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L Earthing complete with galvanised iron earth plate electrode of size 60 x 60 x 0.60 cm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia (upto the cross arms) by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh,RCC cover & frame, PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR Part – I. Note:- The unit rate includes earth lead upto 7.5 metre length from top of earth plate.

M&L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI Strip 32 x 6 mm mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I. Note:- The unit rate includes earth lead upto 7.5 metre length from top of earth plate.

M&L galvanized iron pipe light grade ISI Marked complete for cable protection , laid in trenches, floors, fixed to walls, pole complete all as specified and directed ISI marked. of following sizes. (a) 40 mm bore.

(b) 50 mm bore

(c) 80 mm bore.

M&L LED based street light, housing made up of LM6 pressure die cast aluminium alloy with effectie thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 4000 lumens and maximum system wattage 40 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be wthstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make:CG / Wipro/Philips

M&L LED based Flood light fitting, housing made up of pressure die cast aluminum Alloy with effective thermal management, sturdiness . The fixture should have a minimum system efficacy of more than 115 lumen/Watt and maximum system wattage 200 Watts. The fixture shall have a corelated color temperature of at least 5000K and a CRI of minimum 70 .The fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection of IP66 (lamp and gear Compartment and Mechanical Impact Resistance Rating of IK >=05. The fixture driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF >0.95 and THD<20% .The fixture should comply with the parameters as per IS10322 and for EMI and LM 79 test reports .Including suitable size street light fitting bracket with suitable size clamps,nut bolts and washers as per site requirement complete all as specified as directed by Engineer-in-Charge. Make CG LFLPI 200 CDL of equalient make of Philips / GE.

M&L thermplastic cable junction box with IP 66/67 weather prrof protection for outdoor installation with knockouts for cable entry of size 205x255x122 mm suitable for LT UG cable 10 Sqmm to 25 Sqmm Make Hensel / Sintex

M&L FRLS PVC insulated Copper conductor, two single core of size 1.5sqmm complete for terminal box to street/ flood light fitting.

M&L Stove enamelled, blank rigid conduit 20 mm for terminal box to street/ flood light including fittings complete

M&L automatic street light switch using infrared sensor based Nture Switch, 08 kw equally distributed, 63 Amps,1-pole, Model - Swadeep-02 EC 8 Kw1P for automatic switching of street lights based on LUX level of natural light . The sensor(Nature switch ) along with suitable power contactor rating 63 Amps 3- pole & 40 Amps 2-pole, MCB SP 63 Amps -03 nos and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof ,electric shock proof, termite proof and FR grade SMC Junction box (Sintex make) confirming to IP54.The contactor suitable to 1- phase load of 08 kw , rating 63 amps 3pole, MCB rating 63 amps SP 01 NOS. Make of Nature switch-Kakatiya Energy systems Pvt Ltd.Hyderbad/ Bajaj/Healer.Contactor-BCH/L&T/Schneider (asper IEC-60947-4-1/IS-13947-4-1), MCB- Hager/ Schneider/ Legrand/L&T, Circuit Wiring-Polycab/RR Cable /Finolex.

M&L automatic street light switch using infrared sensor based Nture Switch-, 25 kw equally distributed, 63 Amps,3-pole, Model - Swadeep-02 EC 25 Kw3P for automatic switching of street lights based on LUX level of natural light . The sensor(Nature switch ) along with suitable power contactor rating 63 Amps 3- pole & 40 Amps 2-pole, MCB SP 63 Amps -03 nos and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof ,electric shock proof, termite proof and FR grade SMC Junction box (Sintex make) confirming to IP54.The contactor suitable to 3- phase load of 25 kw , rating 63 amps 3pole, MCB rating 63 amps SP 03 NOS. Make of Nature switch-Kakatiya Energy systems Pvt Ltd.Hyderbad/ Bajaj/Healer.Contactor-BCH/L&T/Schneider (asper IEC-60947-4-1/IS-13947-4-1), MCB- Hager/ Schneider/ Legrand/L&T, Circuit Wiring-Polycab/RR Cable /Finolex.

M&L Switch Fuse Units (Rewireable Type) , Triple Pole, 415V, with Neutral Link capacity, 63 Amps fixed on pole/ wall etc including suitable size clamp, nut bolts etc all as specified and directed. Make Havells/C&S/L&T/ABB

M&L cable route indicator made out of jodhpur stone of size 900cm x 20 cm x 20 cm all finished surface with "LT" lettering size 6 cm x 6 cm engraved on the store complete all as specified by Engineer in charge. Note:1. Necessary PCC and earth work for planting cable route indicator is measured separatly in relevate items.

M&L Cable indoor / outdoor end terminals jointing kit for LV/LT 1100 V cable heat shrinkable type joint kit complete with jointing material and accessories, thimbles etc suitable for 25 Sqmm to 50 Sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing, fixing in replacement complete all as specified as directed by Engineer-in-Charge.

Ditto All as per Srl item No . 36 here in above but 70 Sqmm to 150 sqmm 3.5 Core

M&L Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia. for working pressure 1100 volts grade, complete all as specified and as directed by Engineer-in-Charge.

M&L Shackle type, vitreous, white, brown, or green insulators, including galvanised mild steel strips, washers, insulators bolts, washers and nut for working pressure 1100 Volt, 100mm height 115mm dia, glavanised steel fitting strips of size 21 x 5mm, 14mm dia bolts complete all as specified and as directed by Engineer-in-Charge. Make : Bengal potteries/ Jay Sree/Bikaner ceramics/Mysore.

Supplying and stringing in replacement Aluminium conductor, steel reinforced (ACSR) any type of ACSR conductor as per site requirement of size /make as ordered including stringing for overhead line on LT poles including aluminum binding wire 14 SWG, jumpers, line tapes, conducting jelly etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The ACSR conductors shall be conforming to IS-398 and as specified in SSR Part-I.(ii) The unit rate quoted shall also be deemed to include for supply & fixing of aluminium binding wire, aluminium tapes etc which shall not be included in the weight of conductors.(iii) Weight of conductors shall be determined by measuring true horizontal distance between centers of two adjacent poles and compounding the weight of conductors of that size and length and 3% extra added for sag, jointing, jumpers etc. (iv) Weight of the conductors shall be calculated from the nominal weights given in tables in the relevant IS.)

M&L bus bar chamber of size 300 mm x 300 mm x 150 mm made out of 2 mm thick MS sheet ,painted with one coat of red oxide and two coats of grey colour synthetic enemal paint with 100 Amp capacity 20 cm long 4 No aluminium bus bar fixed of insulator with locking arrangements with provition of cable entry from two sides including fixing arrangement on wall with suitable size anchore bolt 04 Nos complete complete all as specified and as directed by Engineer- in- charge

Dismantling of ACSR of any size.

Dismantling poles/struts any size

Dismantling cross arms of MS channel angle sections etc. complete

Dismantling insulators any type any size

Dismantling stay wire with bow and stay rod.

Dismantling earth wire or copper conductor,service feeder or distributor span

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

M&L Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 50 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 50 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 50 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

M&L Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Legrand/Wipro/Havells

M&L Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Make : Legrand/Wipro/Havells

M&L Socket outlet flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : - Legrand/Wipro/Havells

M&L Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : SSK /Leader

M&L Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Legrand/Wipro/Havells

M&L Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/Wipro/Havells

M&L Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge. Make LEADER/SSK.

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by engineer-in-charge.Make Surya /Phillips/wipro/CG /Bajaj

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 8/10 Watt(2Fit) complete all as specified and directed by engineer-in-charge.Make Surya /Phillips/wipro/CG /Bajaj

S & F LED recess mounting luminarie fitting 36 W of size 2' X 2' back lit LED panel having white CRCA body, high quality PMMA diffuser. Separate HPF driver. Suitable for Armstrong and Grid ceiling.CCT 5700K , make : Polycab/Bajaj/ Havells/Philips.

Supply and fixing Street light bracket in replacement, made of GI pipe 40mm bore, light grade not less than 1.2 m long bent to shape including fixing with 2 nos suitable size of MS flat iron clamps, nuts, bolts and washers and making connections all as directed by the Engineer-in-Charge.Make of GI pipe : Jindal/Surya/Prakash

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 2500 lumens and maximum system wattage 25 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG/C&S/Bajaj/Havells

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 12 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard/BCH/HPL

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Schneider/ HPL/Legrand/ GE/ Seimens/L&T/Indo sian/C&S/Havells/BCH/ABB

S&F MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ GE/ Seimens/L&T/Indo Asian/C&S/ABB/BCH /Havells

Supply & fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 Volt. complete all as specified and directed by Engineer in charge.

S&F concealed sub main wiring and providing new sub main wiring with 3 core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 4 sq mm drawn PVC concealed conduct including earth continuity conductor cable of size 4 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

S&F concealed sub main wiring and providing new sub main wiring with 3 core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 6 sq mm drawn PVC concealed conduct including earth continuity conductor cable of size 6 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 415 volts with 200 Amps rated bus bar, load line DB's are fittied with bus bar nutural links blank plates TPN vertical load line 4 ways suitable for TP/FP 'A' frame MCCB,includeing 100 Amps MCCB -01Nos ,MCB SPN 32 -04 Nos and MCB SP as required, complete all as specified and as directed by Engineer-in-Charge. Make - Havells or equivelent Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/ABB/BCH/HPL Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings complete, laid in trenches, including connections of 25mm bore, complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 50mm bore with & including all fittings complete, laid in trenches, including connections of 50 mm bore, complete all as specified and directed.

S&F 25mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed.

S&F 50mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 100 mm bore GI/DI water pipe line including drilling and welding of 25/50mm GI socket and necessary rubber insertion, nut, bolts & washers complete all as directed.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level.

Dimantling water tanks cap exc 250 & n.exc.500ltrs.

Taking down chowkhats or frames not exc. 1.50sqm each but with shutter (w/o taking of shutter from the frame )

Taking down chowkhats or frames exc. 1.50sqm each but with shutter (w/o taking of shutter from the frame )

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water including all necessary finishes (tiles,mosaic etc ) of any thickness complete all as specified.

M&L for coloured non skid ceramic tiles 300 x 300 x 7mm thick in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in CM 1:6

M&L Glazed ceramic tile 450 x 300 x 06-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified.

M&L for17-18mm thick granite machine cut slab table rubbed and polished granite as on cooking platforms incl. pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade laid over 20mm thick cement screed in cement mortar 1:6.including all necessary mouldings, making holes for gas pipe etc complete all as directed.

Racking out joints/pointing to brick work or stone patti ceiling laid flat in lime concrete complete

M& L flush pointing in cement mortar 1:3 on ceiling surfaces of stone patti laid flat in lime concrete complete

M&L Brickwork with sub class bricks (old sized bricks ), straight or curved on plan exc 6 m mean radius, built in ement mortar 1:4

S&F Rotational moulded polythene water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 500 ltrs

S&F factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately

S&F framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type B-21 of 100mm.

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 150mm

M&L Aluminium handles cast type anodised of 150mm

M&L Stainless steel wire cloth 0.56mm nominal dia of wire and avg.width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples fixed in any position.

M&L sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane

M&L Rendering 15mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:4,even and smooth w/o using extra cement .

M&L for Preparing new plastered or unplastered surfaces of walls and applying three coats of white wash on ceiling complete.

M&L for Preparing old plastered or unplastered surfaces of walls and applying one coats of white wash on ceiling complete.

M&L Preparing old finished surfaces of walls including cornices, pilasters etc and applying one coat of distemper oil emulsion, white or tinted as directed by the Engr in Charge.

M&L Preparation of old plastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over a coat of primer as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge.

M&L Preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

M&L Preparing old surface of steel of any desc over 10cm width or girth and applying one coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing.

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 15 mm .

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing.

S&F steel water tubing 20mm dia and connection ,incl cleaning for refixing .

M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete lived in repairs and making good to floor complete.

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete.

S&F Pvc connection 15mm size with PTMT nuts of length 450mm.

S&F Vitreous china wash basin, white flat back, size 580x450 excluding traps waste pipe fixed with brackets fixed in repairs.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified .(Min weight 45 to 60 gms .

S&F kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers and waster, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and conneting union to pipe overall size 915mm x 460mm bowl size 410 x 330 x 160mm

S&F Waste pipe 40 mm for SINK with coupling fixed in repair

S&F Bib tap standard of PTMT 15 mm bore any colour high pressure screwed for iron pipe fixed. (minimum weight 15 mm 90 gms/20 mm 125 gms

S&F 15 mm dia bore brass chromium plated stop cock concealed type with long shank for iron pipe.

S&F Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F Chromium platedshower rose with swivel jointas 75 mm size

S&F Towel rail 600mm long of cast copper alloy, chromium plated, fixed in repair complete all as specified and directed by Engineer-in-charge.

S&F PVC Toilet cabinet with shelves and shutters fixed with looking mirror of size 600 x 450 mm (Make : Commander or equivalent) 5 mm thick glass

S&F Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia fixed in repair

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

S&F PVC floor trap 75 mm incl CP grating

S&F PVC floor trap 110 mm incl for WC Connector

Dismantling pipe of any description fixed to wall or laid under floor

Refixing of PVC storage water tanks of any capcity

M& L PVC (SWR) bends any radius 110 mm bore with oval acess door.

M& L PVC (SWR) bends any radius 75 mm bore with oval acess door.

M&L PVC (SWR) junction single, (Single T) equal or unequal 10 mm bore with oval acess door.

M&L 15 mm dia bore brass chromium plated long body bib taps .

M&L stainless steel soap dish all as specified .

M&L 15 mm dia bore cetre hole WHB mixer with and including necessary fittings.

M&L Rendering 15mm thick cement plaster on fair faces of brick or conc. Surfaces in cement mortar 1:6,even and smooth w/o using extra cement .

M&L 15 mm dia bore 450 mm long PVC connection with PTMT nuts.

M&L Stainless teel Peg set of 5.

M/s Rohit Construction Co.

M/S BUDHRAM BISHNOI