Upgradation of DIET Leh as centre excellence Phase II

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

Dumping of stone In Horizontal level including cost of stone

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Centering and shuttering including strutting, propping etc. and removal of form for: Foundation,Plinth Beam, footing bases of column Foundations, footings, bases of columns etc. for mass concrete.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, piers, abutments, posts and struts.

Suspended floors, roofs, landings, balconies and access platforms.

Slab Edge Shuttering - Under 20cm Wide

Stairs (excluding landings) except spiral staircases.

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts etc. upy floor five level excluding cost of centering, shuttering, finishing and reinforcement: (1:1.5:3) 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 5.3.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing & fixing upto floor five level compressed stabilized earth blocks (CEB) made an appropriate mix of dry inorganic subsoil, non-expansive clay, sand, and aggregate with 5% cement as stabilizer, in mud mortar, including cost of materials complete.

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:3:6(1 cement :3coarse sand :6graded stone aggregate 20 mm nominal size)

WALL PLASTER - EXTERIOR CEMENT PLASTER (IN FINE SAND) 12mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand)

6mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, - M.S. tube

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 50 mm thick with 20 mm nominal size stone aggregate

20mm cement plaster finished with a floating coat of neat cement of mix : 1 : 3 ( 1 cement : 3 fine sand)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and onforming to IS: 15622, Shade and Texture as approved by Architect In charge. Laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600x600 mm

Providing and laying Vitrified Full Body Floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and onforming to IS: 15622, Shade and Texture as approved by Architect In charge. Laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of tile 600x600 mm

LAMINATED FLOORING Providing and fixing Interlock Laminate (AC-4) 12mm on floors including necessary fittings and accessories like base foam and edge beading.All Job Complete

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab with Shade as approved by Architect in charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 250x10 mm

Providing and fixing bright finished brass 175mm mortice latch and lock with 6 levers and a pair of leverhandles of approved quality with necessary screws etc. complete. Make Godrej Model no- ELC 06 , Hettich, Dorma or Equivalent

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.Of make Godrej, Dorma or equivalent

Providing and fixing factory made uPVC White colour Double glazed windows/ Doors comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. Cost inclusive of double glass panes and silicon sealant ) and necessary fittings. Double Glazed Panes to have inert gas(Argon) filled gap and UPVC Door shutter( wherever required). All job Complete Approved quality.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3.On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/ grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in- Charge. (Final coat to be done in 1 or 2 layers without gap of time.) Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Designing, Supplying, Assembling / fabricating, Installation, finishing, testing and fixing in position of Concrete Jaali Blocks of approved make, color, shape, size & design to be installed in the External Elevation,complete to the satisfaction of the Architect & Engineer in charge and as per directions .

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; Budloo wood

Dry random rubble masonry with hard stone in foundation and plinth: 7.3.1 With bond stone.Tie Beam at Mid Height of Thickness 1 feet

Providing and applying polyurethane insulation foam in the exterior cavity walls , having an eveen thickness of 3 inches.All work complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (Hessian based self finished bitumen” felt) and fourth and final course of stone grit 6mm and down size or peasized gravel spread at 6 cubic diameter per square metre including preparation of surface but excluding grading complete with : Bitumen felt (Hessian base) type 3 grade I conforming to IS : 1322.

Carriage of material by MT from source to site of work including loading, unloading complete job Cement & Steel -----------5 Km

Sand -------10Km

Stone Aggregate--- 10 km

Stone Blocks -------10 Km

Earth-------10 Km

Supply and install white vitreous china Rimless single piece water closet (European type) with Soft close slim seat cover (size: 655mmx355mmx720mm), and CP flush bend with fittings and C.I. brackets, 40mm flush bend, S Trap 220mm, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required (Make: Jaguar Cat No.CNS-WHT-851S300SPP, Essel Cat No. 77091653, or equivalent)

Supplying and install white vitreous china urinal with spreader of size 355x 340x535mm approx having water inlet from back side including fixing to wall with suitable brackets all as per manufacture specification and direction of engineer make jaguar cate number URS-WHT 13261 H Essel cate number 73011010 or equivalent

Supplying and install thin rim Wash basin vanity in white color for over counter mounting ( Size 463mmx 325x 135mm ) specially fabricated brackets, painted white 32mm dia cp waste coupling and 12'' bottle trap with nipple nut ring and rubber washer etc complete white C.P wall flange and rubber adoper for waste connection comple including cutting and making good the walls wherever required, ( make : jaguar cat No solo sls-wht-6901, Essel Cat No 72031300, or equivalent )

Supply and install CP brass single lever hi flow wash basin mixer with wall mounted exposed part and concealed installation- Diverter (35mm) complete including cutting and making good the walls where required. (Make: Jaguar Cat No. OPP-15233NKPM, Essel Cat No. 132301(Exposed Part) ,180208(Concealed Part) , or equivalent)

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: 510x1040 mm bowl depth 225mm.

Supply and install CP brass Sink mixer - wall mounted with full motion 355mm extended spout and aerator complete including cutting and making good the walls where required. (Make: Jaguar Cat No. LYR-CHR-38165, Essel Cat No. 131269, or equivalent)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Supply and install hand shower (Health faucet) Flow rate at 45 psi ≤ 6 lpm with 1.2mtr long Easy Flex Tube in chrome finish and wall hook.(Make: Jaguar Cat No.ALD-563 , Essel Cat No.309003 or equivalent)

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with CP brass screws and washers.

Supply and install Toilet Paper Holder complete including cutting holes in wall and making good the wall wherever required. (Make: , Essel Cat No.131027 or equivalent)

Supply and install of cp brass soap dish of approved design (Make:Essel 124024 or equivalent)

Supply and install of 20mm dia C.P shower arm 18" long with 8" over head rain shower (single flow )with wall flange including cutting and making good the walls, wherever required. (Make: Jaguar Cat No. SHA-479L450(shower arm) OHS-1759(shower head) , Essel Cat No. 306318(shower arm) 303008 (shower head), or equivalent)

Supply and install of 45mm single lever hi flow divertor(Exterior + Concealed) with with spout and with wall flange including cutting and making good the walls, wherever required. (Make: Jaguar Cat No.LYR-38079NK(Exposed Part), ALD-079N(Concealed Part), Essel EQUA Cat No.202004(Exposed Part) ,180105(Concealed Part) , or equivalent)

Providing and fixing soundproof Multilayer Polyproplene piping system as per EN 1451-Part 1-6 with 3 layer pipe made of PP + PP-MD + PP in white color and three layer fittings in PP MD, push-fit type,Halogen and Calcium free, having high impact resistance as per DIN EN ISO 291:2008-08 , Ring stiffness SN6 6KN/m2 as per ISO 9969, offering sound levels of not more than 17 dBA as per EN 14366 at a flow rate of 4 l/s, water tightness as per EN 1451-1 minimum of 0.5 bar for 15 minutes, density of pipe = 1.15gms/cm3, elongation = 0.09mm/m0K and E modulus 2300-3000 as per ISO 178, along with factory fitted EPDM lip ring. (Including pipe, fittings and supports complete in all respect.) 40 mm OD (class 3 (6 kg/cm2)

50 mm OD (class 3 (6 kg/cm2)

63 mm OD (class 3 (6 kg/cm2)

100 mm Dia

Providing and fixing Polyproplelene (PP) P-Trap including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects 100 x 100 mm outlet

Providing & fixing (PP) inlet fitting with one or more inlets fabricated from 110 mm outer dia (PP) pipe and solvent welded sockets and fixed to (PP) Trap and set in cement concrete as per drawing complete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources

Providing, fixing and testing of reducing floor drain of 110x63 mm OD as floor drain in cement concrete 1 : 2 : 4 float with floor complete in all respects as directed by Engineer-incharge complete as per standard design.

Providing and fixing 125 mm dia, 1 mm thick CP grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete in all respects as directed by Engineer-incharge complete as per standard design. 125 mm dia

Providing and fixing in position 125x125 mm square / 125 mm dia stainless steel cockroch trap consisting of 0.45 mm thick inner and outer cup and 1.0 mm thick top grating (Jali) with ring to be fixed inside uPVC ‘P’ traps with cement concrete. (for kitchen and pantry)

Providing, fixing, jointing and testing of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) including injection moulded fittings with bosses like tees, bends, access door bends, single/double 'Y' , crosses, reducers, end caps, cowl etc. with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, including under floor or fixed to walls and ceilings with Hilti powder coated pipe support channel, clamp with EPDM rubber, rod/hardness, fastner, nuts, bolts etc. as per manufacturer's recommendations complete including cutting and making good the floors and walls where required complete in all respects as directed by Engineer-incharge complete as per standard design. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Chajge. (Concealed work including cutting chases and making good the walls etc.,) PN-16 Pipe, 20 mm OD (SDR-7.4)

PN-16 Pipe, 25 mm OD (SDR-7.4)

PN-16 Pipe, 32 mm OD (SDR-7.4)

PN-16 Pipe, 40 mm OD (SDR-7.4)

PN-10 Pipe, 50 mm OD

Providing & fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape, rockwool 6 inch per side wire mesh , polyethlene tapping with cello tape aluminium sheet 26 gauge cladding with dia complete job including carriage 9mm thick 50mm dia (OD) PPR 20mm

19mm thick 50mm dia (OD) PPR 32mm

19mm thick 50mm dia (OD) PPR 40mm

Providing & fixing of material for the insulation of pipe with nitrile tube, tapping with cello tape for inner wall fittings, complete job including carriage, 19mm thick 50mm dia (OD) PPR 25mm

Providing & fixing heat tape 33 watt on PPR pipes made of denforced or chromelox or equivalent make , as approved by engineer in charge , complete job

Providing and fixing ball valve (brass) of approved quality complete : High or low pressure with plastic floats: 20 mm nominal bore

25 mm nominal bore

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 40 mm dia

50 mm dia

Providing and fixing motorised valve (with by pass line including ball valve) with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box, pipe, butter fly/ball valves, flanges, union, nutbolt etc., complete in all respects as directed by Engineer-incharge complete as per standard design. 32 mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources

Providing and Fixing of material for the insulation of water storage tank of with nitrile sheet, tapping with cello tape, rockwood 6 inch per side, wire mesh, polythene, aluminum sheet 26 gauge cladding with dia of, complete job. 19 mm thick nitrile sheet.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and the base support for tank

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kind of soil Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With FPS Brick.

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With FPS Brick.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as perstandard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. Extra for depth for manholes size 90x80cm

Extra for depth for manholes Size 120x90 cm

Supplying, installing, testing, and commissioning of a 2000 LPD solar water heating system with a heat exchanger type, including electrical heater backup, 1000 Ltrs. make-up water tank, recirculation pump, and electrical Panel. (As per the Approved Technical Data sheet).

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required Group A

wiring of following light point with 1.5 sq.mm FRLS PVC insulated copper conductor cable in PVC conduit recessed including chasing of wall, filling of chases with cement mortar 1:3 mix and /or fixing conduit on surface of wall/ceiling including fixing of saddles etc. including modular range of plate switches, modular cover plate, ceiling rose, surface or deep tee, circuit wiring (2x2.5+1x2.5), 1.5 sq.mm FRLS PVC insulated copper earth wire, etc. complete as required. One point controlled by one number 10 Amp MCB (First point)

Looping Point above

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 25 mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supply & fixing of Universal Socket with 4.0 sq.mm PVC insulated multistranded copper conductor cable (FRLS Type) in surface / recess 1.8 mm thick PVC conduit including cutting the chases in wall & making good the same including providing & fixing of M.S. Switch & outlet box, modular range 13Amp switch with 3 pin 13Amp socket, modular cover plate, earthing with 4.0sq.mm PVC insulated copper conductor cable / wire (FRLS Type) etc. complete as required & as per specifications.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 6 way (4 + 12), Double door

6way (4 + 18), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Supply & fixing of 20A Switch socket with 4.0 sq.mm PVC insulated multistranded copper conductor cable (FRLS Type) in surface / recess 1.8 mm thick PVC conduit including cutting the chases in wall & making good the same including providing & fixing of Switch & outlet box, modular range, earthing with 4.0sq.mm PVC insulated copper conductor cable / wire (FRLS Type) etc. complete as required & as per specifications.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. TV antenna socket outlet

Telephone Socket Outlet

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

SITC OF 9 W LED 6500 K Slim, compact, auminum die cast edge lit panel. Recess mounted round fixture with opal diffuser and separate electronic driver. MAKE :- Havells

SITC of 10 W WH LED Bulkhead Light as/Specification,PDC AL Housing,system watage -10 w,Lumen pack - 800 with eficacy - 800lm/w,CRI-80. , IP -65,Surge protection - up to 5 kv with IS 10322 (part 5/Sec.1)-2012.SITC of 5 W WH LED Mirror Light

Supply installation testing commissioning of 10W Wall bracket light

Supply installation testing commissioning of 20W SFTL

Supply, Installation, Testing & Commissioning of Network WDR 2MP IR Rugged Mini Dome Camera having 12.8” 2 Megapixel progressive CMOS image sensor, Min. Illumination required 0.002ux/F1.5(color,30IRE) 0Lux/F1.5(IR on), 120dB True WDR, H.265/H.264B/Smart Codec / MJPEG (Sub Stream), 2.7mm~13.5mm, Motorized, F1.5 lens, Smart IR with upto 40m IR distance, Up to 128 GB microSDHC card, Class 10 (not included), DC12V, PoE (802.3af) (Class 0), ingress protection IP67, vandal resistance IK10, ONVIF Profile S/G/Q, FCC Part 15B, EN 55032,EN 50130-4,UL 60950-1, EN 62368-1,EN 50581,etc as required. (HONEYWELL/CP PLUS/HIKVISION) or equlvent

Supply, Installation, Testing & Commissioning of Network WDR 2MP IR Bullet Camera having 1/2.8” 2 Megapixel progressive CMOS, 2.7 mm – 13.5 mm MFZ Lens,True day/night (IR-cut filter),Wide dynamic range up to 120 dB,Low-light performance down to 0.002 Lux / F1.5 (color, 30IRE), 0 Lux (IR ON),Up to 197 ft (60 m) IR lumination, H.264/H.264B/H.265/Smart Codec/MJPEG (Sub Stream) , Support up to Up to 128 GB micro SDHC card, Class 10 (not included), DC12V or PoE (802.3af)(Class 0), IP67 INGRESS PROTECTION ,ONVIF Profile S/G/Q, FCC Part 15B, EN 55032, EN 50130-4, UL 60950-1, ROHS- EN 62368-1, certifications, etc as required.(HONEYWELL/CP PLUS/HIKVISION)

Supplying , installation , Testing commissioning integeration of 24- channel 4k NVRs- Third- [arty network camenas supported Up to 5 Megapixels resolution recording with 2 SATA PORT UP TO 12 TB Supported support 1- ch HDM1, 1- CH VGA, HMDI at up 4k ( 3840x 2160 ) resolution 4- ch network cameras can be connected with 40M / 60 M /80M income band width Support dual-os to ensure high reliablity of system running Support various VCA detection alarm and VCA search support H . 265/ H 264/ MPEG 4 video formate.

Supply, installation, testing and commissioning of 4TB Surveillance Hard Disk S V SERIES-offer high capacities, durable reliability and performance tuned to the high-write workloads of today’s 24×7 video surveillance systems as required. ( SEAGATE/WD/HITACHI)

Suppling,Laying & fixing of 15 MTR HDMI cable on surface as reqd .(Stackfine/Extron/Kramer)

Supply, installation, testing and commissioning of 3 KVA UPS with 30 minutes back-up with inbuilt battery complete etc as required. (APC/MICTOTEK/VGUARD)

Supply, installation, testing and commissioning of 32" LED monitor includes Screen size :43" Diagonal Size, LED BLU type technology, resolution- 3840 X 2160 ,250 nits brightness, 4700:1 contrast ratio, stereo mini jack, HDMI I/p-2 , USB-1, compatability for wifi, bluetooth suitable for operation on AC Power supply AC 240 V~ (+/- 10 %), 50/60 Hz,etc required.(SAMSUNG, Model – BE 43TH/SONY/LG)

Supplying instalation testing & commissioning of fault isolator complete with base as required

Supplying instalation testing & commissioning of intelligent anolog addressable photothermal detector complte with mounting base complete as required ( if the device does not have inbuilt isolator module then the bidder has to provide isolator module after every 15 devices within the detector and for this nothing extra shall be paid )

Supplying installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying installation testing & commissioning of addressable manual call point complete as required Approved by EN 54/VDS/LPCB/UL

SITC of contact dual input module used for monitoring contacts and signals to the Fire Controller, status of monitored contacts and wiring to the contacts can monitor a single normally closed contact. Approved by EN54/VDS/LPCB/UL.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying & laying of 2 x 1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

SITC of Digital 250 W (mini.) Class D, high efficiency amplifier shall be an EN54-16 compliant and certified system device in a 2 RU, 19”cabinet . The amplifier shall be permanently monitored by the system controller. A special standby mode shall be provided for saving energy during the time the amplifier is not is use with respect to all economical and supervision aspects. • 480 Watt Class D amplifier • 4 channel input on RJ45 connector, amp link in and out (4 channel dynamic input channel switching for each amplifier • Amplifier efficiency >= 78% • Limiter prevents audible distortion Signal to noise ratio, A-weighted: >104 dB

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning talk back slave station in surface/ recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/ microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.