TP1-071/2019-20

Amount

Fixing bore well point by well qualified geologist lincluding cost of all materials labours, lead and lift etc., complete as direted by the departmental Engineer at site

Drilling of 12" dia. Vertical borewell so as to have a finished size of 6" dia. Bore well in Boulder area to any required depth as decided by the TWAD Board officers by direct rotany mud circulation method using contractor's rigs, tools, labour etc.,

Reaming from 175/200 mm dia pilot bore up to required depth below ground level as directed by the Engineer at site.

Supply the 160mm Special Blue casing pipes (with slot or without slots) including cost of pipes, all lead, lift, etc., complete. 160 mm casing pipe [ without slot ]

Supply the 160mm Special Blue casing pipes (with slot or without slots) including cost of pipes, all lead, lift, etc., complete. 160 mm casing pipe [ with slot ]

Supply the 160mm Special Blue casing pipes (with slot or without slots) including cost of pipes, all lead, lift, etc., complete. 160 mm End cap

Labour Charges for inserting the casing pipes assembly (with slot or without slots) in the drilled hole including the joints pipes etc., complete and supplying and packing the annular space with pebbles of size and quality as approved by the Executive Eng

Charges for developing the bore well for the entire depth with suitable air compressor (minimum 8 hours) including transportation charges for Air Compressors as directed by TWAD Board officers and conducting yield test by "V" notch method. Using 300 cfm.

Supplying and erection of 3HP ELGI Compressor or any other requted make of pump having ISI make with 3 Phase suguna or any other approved make 400 V/440/50 cycle motor (5 HP) having ISI make or as approved by the Board Engineer at site with air pipe of 20 mm dia to pump water to height of 175 Mtrs. and delivery unit with foot valve V belt arrangement including cost of al materials, labour erection charges as per the instructions of Engineer incharge at site etc., complete in all respects and 5 HP 400 /440V L&T make starter to suit the compressor including the cost of all materials, labour, lead, and as per the instruction of Engineer incharge at site complete in all respects.

Supplying, laying and jointing of 40 mm dia HDPE pipes [class - 5.1 Mpa or 10 Kg / sq.m pressure] of Approved quality / ISI make for sub mersible pump in bore well including fixing pipe with motor / any specials, cutting and jointing where ever required,

Supplying, laying and jointing of 20 mm dia HDPE pipes [class - 5.1 Mpa or 10 Kg / sq.m pressure] of Approved quality / ISI make for sub mersible pump in bore well including fixing pipe with motor / any specials, cutting and jointing where ever required,

Supplying and fixing approved make for 1 no sintex water tank of the capacity 1000 litter

Engaging JCB excavator for uprooting trees levelling approach road filling low lying areas on hourly basis

Earth work excavation with intiial lead, lift etc., complete Hard stiff clay, stiff block cotton hard red earth, shales, muram gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil.

Earth work excavation with intiial lead, lift etc., complete Soft disintegrated rock laterite soft rock (or ) kankar not requiring blasting

Earth work excavation with intiial lead, lift etc., complete Medium rock dense medium rock not requiring blasting

Earth work excavation with intiial lead, lift etc., complete Hard rock by weding & chiseling in proper shape

Providing PCC 1:4:8 using 40 mm HBG metal for foundation including cost of all materials labours, lead and lift etc., complete as direted by the departmental Engineer at site.

Providing PCC 1:3:6 using 40 mm HBG metal for foundation including cost of all materials labours, lead and lift etc., complete as direted by the departmental Engineer at site

PCC 1:2:4 using 20 mm HBG Metal for foundation with out form work including cost of all materials labours, lead and lift etc., complete as direted by the departmental Engineer at site

PCC 1:2:4 using 20 mm HBG Metal for foundation with form work including cost of all materials labours, lead and lift etc., complete and as direted by the departmental Engineer at site

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement and as direted by the departmental Engineer at site. Raft & Footings

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Column below GL & Gate pillars

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Cable duct wall.

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Culvert and retaining wall.

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Grade beam

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Plinth beam

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Column above GL

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Lintel cum sunshade

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Beam

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. 130mm thick RCC roof slab,

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. 100mm thick RCC roof slab

R.C.C 1:1.5:3 using 12 to 20 mm HBG metal with form work including cost of all materials, labour, lead lift and curing etc., complete but excluding cost of steel reinforcement. Cover slab

Brick work in C M 1:5 using good quality secound class chamber burnt bricks for basement including cost of all materials labour, lead & lift etc., complete and as directed by dept engineer at site.

Brick work in C M 1:5 using good quality secound class chamber burnt bricks for superstructure including cost of all materials labour, lead & lift etc., completeand as directed by dept engineer at site..

Brick work in C M 1:3 using good quality secound class chamber burnt bricks for superstructure including cost of all materials labour, lead & lift etc., completeand as directed by dept engineer at site.

Refilling with excavated earth other than sand including cost of labour, lead and lift etc., completeand as directed by dept engineer at site.

Filling sand with the foundation and basement with river sand including watering and consolidation as per standard specification, including cost of all labour, material, lead and lift etc., complete and as directed by dept engineer at site.

R.R Masonry in CM 1:5 using random rubble including cost of all materials leads and lifts etc. complete and as directed by dept engineer at site.

Supplying and tying chain link size 50mm Sq. 1.80 m ht including cost of all materials, labour, lead, lift etc.complete and as directed by dept engineer at site.

Providing and fixing 10mm dia GI bolts with minimum 100 mm long and thread and two number washers and nuts for corner posts painting one coat of red oxide and aluminum paint including cost of all materials labour lead lift etc complete

Filling with well gravel including cost of all materials leads, lift, labour etc., complete and as directed by dept engineer at site.

Filling with stone dust including cost of all labour, materials, leads, lift,etc., complete and as directed by the department engineer at site.

Filling with 12mm chips including cost of all labour, materials, leads, lift,etc., complete and as directed by the department engineer at site.

Supplying and filling 40mm BG metal for inside of dispension trench and around the loose jointed stone ware pipes as per drawing and specificaiton including cost of all materials,labour,lead and lift etc., for septic tank complete and as directed by dept engineer at site..

Providing steel reinforcement for all RCC works including cutting, bending, tying, binding and fixing in position including cost of steel and binding wire, labour, and lift etc., complete and as directed by dept engineer at site.

Plastering with CM 1:3,12mm thick celling and sunshade including cost of materials all labour,curing, lead, lift etc., complete and as directed by dept engineer at site.

Plastering with CM 1:5, 12mm thick for inside and outside walls including cost of all materials, labour, curing leads and lift etc., complete and as directed by dept engineer at site.

Flush pointing with cement mortor 1:3 for exposed surface of RR masonry including cost of all materials, lead, lift, curing etc. complete and as directed by dept engineer at site.

Supplying and assembling of template for foundation bolt and nut including cost of all materials lead lift labour etc. complete and as directed by dept engineer at site.

Providing grout holes at required position including cost of all materials, curing, labour, lead, lift, etc., complete and as directed by dept engineer at site.

Supplying and fixing GI bolt and nuts with minimum 100mm long bend and thread 100mm including all materials, labour, lead, lift etc., complete and as directed by dept engineer at site. 20mm dia - 1.5 mtr length

Supplying and fixing GI bolt and nuts with minimum 100mm long bend and thread 100mm including all materials, labour, lead, lift etc., complete and as directed by dept engineer at site. 25mm dia - 1.5 mtr length

Labour Charges for fixing 90 lbs rails including cost of all materials, labour, lead and lift etc., complete and as directed by dept engineer at site.

Flooring and laying marbonite tiles 0.60 x0.60 m (Naveen, Johnson, bell make) in CM 1:3,20 mm tk in pointed with same colour cement including cost of all materials, labour, lead and lifts etc., complete in all respec and as directed by dept engineer at site.

Flooring and laying non slippering tiles 0.3x0.30m (Naveen, Johnson, bell make) in CM 1:3 in pointed with same colour cement including cost of all materials, labour, lead and lifts etc., complete in all respects and as directed by dept engineer at site.

Supplying and laying acid proof tiles of size 300x300x6mm in cement mortar 1:3, 20mm thick and pointing with white cement using 0.40 Kg/ Sq.m approved colour and quality as directed by the engineer at site including cost of all materials lead lift labour etc. complete and as directed by dept engineer at site..

Dadooing and laying glazed tiles 0.3 x 0.15 (Naveen, Johnson, bell make) in CM 1:3 in bath and FOL and pointed with same colour cement including cost of all materials, labour,lead,lift etc., complete and as directed by dept engineer at site.

Dadooing walls with Acid proof tiles of size 150x150x6mm laid in C.M (1:2 ) 20mm thick and pointing with white cement using 0.40 Kg. Sq.m approved colour and quality as directed by the engineer at site including cost of all materials lead lift labour etc. complete and as directed by dept engineer at site.

Providing and laying weather proof cooling white tiles 300x300 size over screed concrete 1:3:6 with average thickness of 25mm for required gradient and using best quality of one course of weather proof tiles of approved quality using CM 1:3, 12mm thick and using 3mm spacer and pointing with water repellent U bond and grout inclusing cost of all materials, labour, lead, lift, transport, curing, etc., complete and as directed by dept engineer at site.

White washing two coats using emulsion paint inside walls two coats including cost of all materials, labour, leads and lift etc., complete and as directed by dept engineer at site.

Painting the walls with emulsion paint two coat over one coat primer including coat of all materials, scoffolding, labour with all lead, lift etc., complete as per specification and as directed and approved by the dept engineer at site

Painting two coats of approved acid resistance paint over one coat of primer for battery room including cost of paint,labuor,lead and lift etc., complete and as directed by dept engineer at site.

Supplying and fixing of 100mm dia PVC rain water down fall pipe of approved quality with the bottom clamps shoes, bend coupling etc., including cost of all materials,labour,lead,lift, for fixing in position etc., and jointing of properly and making holes in masonry on concrete and restoring the attended surface to original condition complete in all respects and as directed by dept engineer at site.

Providing Oriya type W.C approved make of 640mm x 450mm size with trap connection 'Y' bend etc., complete and connecting the same to the main sewer or taking to a length of 2.45m from outs face of the wall if the main sewer is not within 2.45 m and provided with PVC 100mm dia ventialating shaft 4.20m height including cost of all materials,leads,lift,etc., complete and as directed by dept engineer at site. .

Supplying and fixing approved make white glazed wash basin of size 500x400mm fixed on cost iron brackets screws with plugs and screws with 1No. 15mm dia CP screws down 75mm nose pillar tap approved make chain plug and waste coupling 32mmCP adopter including 12.5mm CP drop valve with various cleaning under proof joints including filling to gap between edges and wall with white cement and supplying and fixing 610x407x5.5mm thick plain edged mirror of approved make and hard board backing with detachable edged screws and wall plugs and supplying and fixing towel rod 20x600mm along withpair of brackets of approved size complete in all respects and as directed by dept engineer at site.

Supplying and fixing MS grills for windows 18x4mm thick flats as per specificaitons and drawing with painting one coat of red oxide over with one coat of enamel paint including cost of materials,labour,lead and lift etc., complete.

Providing and supplying for cutting M.S angle at size 50x50x6mm and MS channel to required length fixing in cable duct correct level to alignment complete and as directed by dept engineer at site.

Labour charges for fixing in position of MS chequared plate 8mm thick for cable duct including cost of all materials, labour, leads, lift,cutting,grinding, painting,placing in position etc., complete and as directed by dept engineer at site.

Providing cudappah slab of 20mm thick polised on both sides for cupboard including cost of all mateials,lead,lift etc.,complete and as directed by dept engineer at site.

Construction of inspection chamber at following size 0.60X0.60mtr to an average depth of 0.80m with providing cast iron heavy duty manhole cover, with bracket suitable size including cost of all materials labour CI manhole cover as per drawing and specification (Brick work in CM 1:3, Plastering with CM 1:3, with 5% admixture of water proof compound 12mm thick for inner side and on the out side with CVM 1:3,12mm thick plastering to be carriedout to 250mm below ground level complete in all respects.

Supplying fabrication and fixing in position of anodised aluminium door of various size in accordance with ISI 1868 / 1962 for T bottom gutter arrangement so as to drain the water entry and extended ano. Alu section of bottom track of size 100x45mm with gutter arrangements shutter / plain top & bottom section of size 45x45mmx2mm plain frame 63x38.4mm switch lock special U rubber L angle alu.clip 17.15 x 17.27 x 1.5mm thick at 0.118Kg/m screws and fixing 5mm fristed glass, providing floor gear, all materials, lead lift transportation , labour for fabricating and fixing in position including drilling holes in RCC / brick work with electric power driller etc. complete and as directed by dept engineer at site. . Alu.door fully glazed

Supplying fabrication and fixing in position of anodised aluminium door of various size in accordance with ISI 1868 / 1962 for T bottom gutter arrangement so as to drain the water entry and extended ano. Alu section of bottom track of size 100x45mm with gutter arrangements shutter / plain top & bottom section of size 45x45mmx2mm plain frame 63x38.4mm switch lock special U rubber L angle alu.clip 17.15 x 17.27 x 1.5mm thick at 0.118Kg/m screws and fixing 9mm thick Novapan board / 5mm fristed glass providing floor gear, all materials, lead lift transportation , labour for fabricating and fixing in position including drilling holes in RCC / brick work with electric power driller etc. complete and as directed by dept engineer at site. Alu.door partly pannelled and partly glazed

Supplying fabrication and fixing in position of anodised aluminium door of various size in accordance with ISI 1868 / 1962 for T bottom gutter arrangement so as to drain the water entry and extended ano. Alu section of bottom track of size 100x45mm with gutter arrangements shutter / plain top & bottom section of size 45x45mmx2mm plain frame 63x38.4mm switch lock special U rubber L angle alu.clip 17.15 x 17.27 x 1.5mm thick at 0.118Kg/m screws and fixing 9mm thick Novapan board providing floor gear, all materials, lead lift transportation , labour for fabricating and fixing in position including drilling holes in RCC / brick work with electric power driller etc. complete.and as directed by dept engineer at site. Alu.door fully pannelled with particle board

Supplying and fixing of PVC door of required size single leaf with PVC frame and shsuttering of approved quality and colour including cost of all fittings, handle, tower bolt, aldrop, hold fast etc., complete

Supplying , fabricating and fixing in position of Anodized Aluminium window natural colour sliding type with locking arrangements in accordance with ISI 1868 / 1962 T bottom gutter arrangements so as to drain the water entry and extended Aluminium section of bottom track of size 62x37mm with gutter arrangements for shutter / plain top & bottom section of size 40x18mm at 0.38Kg/m plain side vertical section of size 40x18mm at 0.63Kg / m ventilator bore frame 63x37 at 0.85Kg/m switch lock special U rubber, L angle aluminium clip 17.15 x 17.27 x 1.5mm thick 0.118Kg/m screw and fixing 4mm thick frosted glass of all materials, load , lift, labour for fabricating and fixing in position including drilling holes in RCC work / brick work with electric power driller to the required extent and made to the original after fixing etc., the Aluminium frame is to be anodized with matt finish under the electrically controlled condition

Supplying and fabricating and fixing in position of anodized Aluminium natural colour ventilator louvers type with frame of 63.5x38.10mm 0.85Kg/m glass fixing anodilzed alu. Groove clip with screws and fixing 4mm thick frosted glass louvers, model including cost of all materials lead, lift labour for fabricating and fixing in position including drilling holes in RCC / brick work etc., wherever necessary with power driller to the required extend and made to the original condition after fixing etc., complete and as directed by dept engineer at site.

Wiring with 2 x 1.5 Sqmm (22/0.3) PVC insulated single core unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box in flush with wall with 5A F.T.Switch covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / Tubelight paint / Buzzer paint inclluding cost of all materials lead, lift, etc., complete and as directed by dept engineer at site.

Wiring with 2 x 1.50 Sqmm (22 x 0.30) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable TW box in flush with wall to house the control switch regulator and covered with 3 mm hylem sheet with painting of suitable colour with continuous earth connection of 14 SWG TC wire for fan point (For rheostatic type regulator) std data

Wiring with 2 x 4 SQ mm(56/0.3) PVC unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113 mm TW switch box in flush with wall with 3 mm thick hylem sheet cover for 5 A 3 pin flush type non interlocking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point (SD 34,35 ) including cost of all mateials, lead, lift, etc., complete.

Wiring with 2 x 4 SQ mm(56/0.3) PVC unsheathed copper conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113 mm TW switch box in flush with wall with 3 mm thick hylem sheet cover for 15 A 3 pin flush type non interlocking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point (SD 39 ) including cost of all mateials, lead, lift, etc., complete.

Supplying and fixing best quality 16Watts CFL bulb with best plastic pattern holder, EI shade including cost of all materials, labour lead, lift etc., complete and as directed by dept engineer at site.

Supply and fixing of water tight bulk head fitting with guard suitable for CFL bulb including cost of all materials, labour lead, lift etc., complete and as directed by dept engineer at site.

Supply and fixing of single box type 4'40 W flourescent fitting complete with copper choke and condenser with TW round blocks on wall or ceiling with flourescent tube with PVC unsheathed copper leads from terminals to the fitting (SD 83)

Supply and fixing of 1200 mm (48") sweeping AC ceiling fan with all accessories and stepped electronic 300 watts regulator with 300 mm (1') down road in the existing clamp including cost of all materials, lead, lift, etc., completeand as directed by dept engineer at site. (SD110)

Supply & fixing of heavy duty industrial AC exhaust fan complete with necessary wall opening and maling good of the wall (SD114) including cost of all materials, lead, lift, etc., complete and as directed by dept engineer at site.

Supply and fixing louvers shutters arrangements for light duty AC exhaust fan (SD.116) including cost of all materials ,lead, lift, etc., complete and as directed by dept engineer at site.

Supply and fixing of 4 way SP DB of 16A /4 way with 32A DP switch with metal clad of 500 V with fuse and neutral (side handle) and one number 25 amps / 30 MA DP RCCB Electricity board on suitable TW board with PWD earthing (SD 139 + 149) including cost of all materials, lead, lift, etc, complete and as directed by dept engineer at site.

Supplying, laying of PVC pipe with required PVC bend L bend, union including cutting, jointing, wherever necessary earth work excavation refilling dismantling masonry if necessary including cost of all materials, lead & lift etc.., complete and as directed by dept engineer at site. 40mm dia

Supplying, laying of PVC pipe with required PVC bend L bend, union including cutting, jointing, wherever necessary earth work excavation refilling dismantling masonry if necessary including cost of all materials, lead & lift etc.., complete and as directed by dept engineer at site. 32mm dia

Supplying, laying of PVC pipe with required PVC bend L bend, union including cutting, jointing, wherever necessary earth work excavation refilling dismantling masonry if necessary including cost of all materials, lead & lift etc.., complete and as directed by dept engineer at site. 25mm dia

Supplying & fixing gunmetal gate value including cost of materials, labour, lead & lift etc., complete and as directed by dept engineer at site. 40mm dia

Supplying & fixing gunmetal gate value including cost of materials, labour, lead & lift etc., complete and as directed by dept engineer at site. 32mm dia

Supplying and fixing 12mm dia PVC bibcock including cost of all materials labour, lead & lift etc., completeand as directed by dept engineer at site.

Supplying and fixing of 12.5mm dia brass charomium plated screw down bib cocks of approved quality including cost of materials,labour charges for fixing lead,lift etc., complete and as directed by dept engineer at site.

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer steel table with threee drawers.

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer 'S' type chair

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer steel half bench of 3 feet length

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer steel stool

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Digital wall clock

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Mirror 1' x 1½'

Supply steel furniture manufacture by 'TANSI' or any other ISI mark including cost of all materials, labour, lead and lift etc., complete. sample to be approved by department Engineer Towel rod

GST for bidders within TamilNadu

GST for bidders outside TamilNadu (IGST)

A.H.CONSTRUCTIONS

K S CONSTRUCTION