PROVN OF COVER SHED FOR VEH PARKING NEAR BLDG NO. T-4 OF 4 CI DET ECIB AND CERTAIN REVENUE AND MINOR WORKS UNDE GE DINJAN

Amount

Surface dressing not exceeding 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, or for shafts, wells, cesspits, manholels, pier holes, laying of cable etc, area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading in layersnot exceeding 25cm, levelling, watering and well ramming as in soft/loose soil complete all as specified and as directed.

Removing excavated/surplus material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

M&L for hardcore of broken stone or boulders guage not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for cement concrete type B0 (1:2:4) (using 12.5mm graded aggregate) for coping complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PCC, type C2 (1:3:6), (using 40mm graded stone aggregate) as in foundations of post holes, filling and mass concrete complete all as specified and as directed.

M&L for 100mm thick PCC, type D2, (1:4:8), (using 40mm graded broken stone aggregate) as in sub base etc complete all as specified and directed.

M&L for 40 mm thick, PCC (1:2:4), type B-0 (using 12.50mm graded broken stone aggregate) as in under layer of flooring and finishing the surfaces rough complete all as specified and as directed.

M&L for precast cement concrete (1:2:4), type B1, (using 20 mm graded aggregate) as in landings, cover slabs of manhole, septic tank etc, and similar articles with plain faces set in cement mortar (1:4) including necessary formwork, moulds etc and incl taking out/removal of existing unserviceable cover slab from manhole /septic tank complete all as specified and as directed. Note : Reinforcement shall be measured and paid separately.

M&L for RCC (Nominal mix), type M-25, (20 mm graded agg) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC (Nominal mix), type M-25, (20 mm graded agg) as in chajja etc complete all as specified and as directed..

M&L for RCC (Nominal mix), type M-25, (20 mm graded agg) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for RCC (Nominal mix), type M-25, (20 mm graded agg) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC (Nominal mix), type M-25, (20 mm graded agg) in column, pillar, piers, post and struts complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc rough finished flat surface of concrete complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished flat surface of concrete complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) complete all as specified and as directed.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F for mild steel TMT bars 8 mm and over for stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) including finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer (water proofing compound measured separately) and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces in cement mortar (1:4) including finished the surface even and fair complete all as specified and as directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

S&F for 15 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

S&F for 20 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

S&F for 25 mm bore, steel tubes, galvanised, medium grade with all fittings with all fitting; laid in trenches etc complete all as specified and as directed.

S&F for 40 mm bore, steel tubes, galvanised, medium grade with all fittings with all fitting; laid in trenches etc complete all as specified and as directed.

S&F for Joist, channel, angle, or tee sections of Fe 290 (Gde E-165) fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats et complete all as specified and as directed.

S&F for rolled mild steel in steel work tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F for roof plates with sleeve pieces riveted or welded thereto, and similar roof and ceiling connection complete all as specified and as directed.

Dismantling of asbestos cement (corrugated or semi corrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of ceiling etc and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of oil bound distemper over a coat of clearcholle primer complete all as specified and as directed.

M&L for second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

M&L for 35 mm thick second class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for 30mm thick, glazed/skelton shutters with second class hard wood,open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, sizes of members of shutter as specified in SSR Part I Section 8, clause 8.24 (b) complete all as specified and as directed.

S&F for 35mm thick, glazed/skelton shutters with second class hard wood, open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, sizes of members of shutter as specified in SSR Part I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter, 30 mm thick (style) consisting of frame, made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 complete all as specified and as directed

S&F for anodised aluminium windows/ventilator sliding shutter, three track way type without sash bars, alumimium sections weighing 0.55 Kg/m including necessary joining cleats, glass clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings, such as peg stays, 150mm long (1 No) hinges type B-21, 100mm long (2 Nos) suitable handle, with complete accessories including glass, wire mesh, anodised aluminium frame (chowkhat) complete all as specified and as directed.

S&F for 75mm long butt hinges, medium weight, cold rolled mild steel fixed to chowkats complete all as specified and as directed.

S&F for 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and as directed.

S&F for 150mm long, aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F for 150mm long, aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F for aluminium handle 100 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F for aluminium handle 150 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick backing coat of cement mortar (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in 1:6 for laying floor finishes complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement and pigment including 75mm thick compacted bed of coarse sand filling with joint fine sand etc complete all as specified and as directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 15mm thick screed bed in cement mortar (1:6) & cutting, edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection, footpath, etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) making impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 ltrs hoisted and fixed in position all as specified in SSR Part-1 complete all as specified and as directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 ltrs hoisted and fixed in position all as specified in SSR Part-1 complete all as specified and as directed.

S&F for 20 mm bore dia of pipe, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20 mm - 210 gms) complete all as specified and as directed.

S&F for 25 mm bore, gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and as directed.

S&F for 40 mm bore, gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and as directed.

S&F for 15 mm bore dia bib taps, chromium plated cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F for 15 mm bore dia, two way bib cock, chromium plated cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make : Cat Part No. G3034A1 Parryware/Hindware/Cera.

S&F for 15 mm bore dia stop valves (concealed type), fancy type, chromium plated cast copper alloy with long shank, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F for 15 mm bore dia angular stop cock/ stop valves, chromium plated cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F for 15 mm bore dia pillar taps, chromium plated, cast copper alloy, fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F for brass chromium plated shower rose, 125 mm size fixing to steel pipe or union complete all as specified and as directed.

S&F for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F for for tubular towel rail, 20mm dia, D type, 60cm long brass chromium plated between flanges complete all as specified and as directed.

S&F for soap dish vitreous china coloured approximate size (160mmx 160mm x 90mm) complete all as specified and as directed.

S&F for PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, with PVC conection pipe 600mm long and flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and as directed.

S&F for vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed.

S&F for 32 mm waste coupling of PTMT (half or full threaded) (Minimum weight 32mm?45gms/40mm-60 gms) complete all as specified and as directed

S&F for vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed. Make : Cat No. C0117 of Parryware/Hindware/Cera.

S&F for vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed.

S&F for vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) front or back inlet including seat cover, connection to drain ( outgoing pipe) and to flushing pipe, anti syphonage pipe, etc and making good to existing surface complete all as specified and as directed. Make : Cat No. C0287/0288 of Parryware/Hindware/Cera.

S&F for plastic water closet seat, black, closed pattern with recessed bottom and cover and mild steel chromium plated hinging device complete all as specified and as directed.

S&F for towel ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and as directed.

S&F in repair health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and as directed.

M&L for salt glazed stoneware drain pipes 150mm internal dia grade 'A' laid in trenches and jointed complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore drain pipes complete all as specified and as directed.

S&F for 16mm of CPVC pipes SDR 11& plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, tranches complete all as specified and as directed.

S&F for 20mm of CPVC pipes SDR 11& plain CPVC SDR 11 fittings on walls/ceiling or laying in floors , tranches complete all as specified and as directed.

S&F for 16mm outer dia, CPVC Brass thread elbow complete all as specified and as directed.

S&F for 20mm outer dia, CPVC Brass thread elbow complete all as specified and as directed.

S&F for 16mm outer dia, CPVC Brass thread Tee complete all as specified and as directed.

S&F for 20mm outer dia, CPVC Brass thread Tee complete all as specified and as directed.

S&F for 16mm outer dia, CPVC Brass thread union complete all as specified and as directed.

S&F for 20mm outer dia, CPVC Brass thread union complete all as specified and as directed.

S&F for 16mm outer dia, CPVC ball valve complete all as specified and as directed.

S&F for 20mm outer dia, CPVC ball valve complete all as specified and as directed.

S&F for 25mm outer dia, CPVC ball valve complete all as specified and as directed.

S&F for 25mm outer dia, CPVC tank adopter complete all as specified and as directed.

S&F for PVC (SWR) floor trap, 75mm dia, plain with grating including jointing with solvent cement including disconnection of old existing trap, and connected with existing water pipe complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

Cutting the existing 50/40 mm bore GI pipe line and making necessary arrangement for taping of new pipe line of 40mm dia including threading, welding and all required accessories complete all as specified and as directed.

M&L for valve pit and construction of brick masonry valve pit of internal dimension 40 x 40 x 40 cm depth with sub class 'B' bricks in CM (1:6) and 10 mm thick plastering in CM (1:4), PCC (1:4:8) type D2 (Using 40 mm graded broken stone aggregate) as in foundation lean concrete, PCC (1:2:4) type CI (using 20 mm graded broken stone aggregate) as in bedding and copping MS frame with 40 x 40 x 5 mm angle iron and 3 mm thick MS sheet cover plate with locking arrangements, hinges and two coats of synthetic enamel paint over one coat of red oxide primer including preparation of surface, two coats of white wash on plastered surface (exposed to view) including necessary excavation in soft loose, soil, returning filling in and removal of surplus soil to a distance not exceeding 50 m complete all as specified and as directed.

M&L for surface point wiring complete with 1.5 Sqmm FRLSH, PVC insulated unsheathed, multi stranded copper conductor single core cable 1100 volts grade, drawn into PVC casing caping 20mm dia with all fittings, including 1.2mm thick pressed steel terminal switch boxes, 3mm thick bakelite sheet top cover(ISI marked) fitted with CP brass screw & washers including provision of PVC insulated FRLSH 1.5 sqmm copper conductor for earth continuity and connected to common earth dolly and brass washers etc. for one light/ fan point controlled by one number one way switch complete all as specified and as directed. Note : Cost of PVC casing caping, cover plate and box of suitable module, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortar (1:4), matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 118 above but for one 3 pin socket outlet, 5 Amps on Independent board.

All as per item No 118 above but for one 5 Amps, 3/5 pin socket outlet on the same board with other switches.

All as per item No. 118 above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 3 pin socket outlet, 5/15 Amps on Independent board complete all as specified and as directed.

S&F for switch piano, 5 Amp single pole, flush type one way 230 volts bearing ISI marked complete all as specified and as directed.

S&F for socket outlet, 2 in 1, 3 pin, 5 Amps, flush type bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 5/16 Amps, 240 volts, bearing ISI marked flush type complete all as specified and as directed.

S&F for ceiling rose, 3 phase/PVC/polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S&F for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F for LED bulb of 9 Watt complete all as specified and as directed. Make : Havells /Philips/Bajaj .

S&F for stepped type(five steps) electronic fan regulator flush type complete all as specified and as directed. Make : Model No. 14502 of Anchor or equivalent.

S&F for 20 Watt, surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed. Make : Cat part No. LTTB4F20WLEDEW Button of C&S/ Havells/ Philips / Bajaj /Crompton/Century.

S&F for factory made board distribution (DB) double door in sheet steel enclosure with common bus bar at incoming end, SPN, 8 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

S&F for factory made board distribution (DB) double door in sheet steel enclosure with common bus bar at incoming end, SPN, 4 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

S&F for MCB, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, breaking capacity 10KA complete all as specified and as directed.

S&F for MCB, 'C' Series, single pole, 240 Volts, 6 to 32 Amps, 'C' Series, breaking capacity 10KA capacity complete all as specified and as directed.

S&F for MCB, 'C' Series, double pole, 240 Volts, 6 to 32 Amps, 'C' Series, breaking capacity 10KA capacity complete all as specified and as directed.

Supply, installing, testing and commissioning of light duty metal anti dust exhaust fan, suitable for Single Phase AC supply, earthing etc, power input 50 W, 220/240 V, 300 mm sweep size, fan speed 1350 RPM, 3 nos. blades, copper winding, Air delivery minimum 1160 CMM and including all fixing accessories complete all as specified and as directed. Make : Model No Tarns Air 12" - reversible of Cropmpton/Bajaj/Khaitan/Havells/Orient.

S&F for 10 Watt, LED, energy saving new generation bulk head luminaire with opal diffuser including lamp incl connecting with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make : Havells/Philips/Bajaj/Crompton/Century.

S&F for 25 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07 complete all as specified and as directed. Make : Havells/Philips/Bajaj.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4mm GI wire by means of bolts and nuts checknuts and washers protected by 20mm bore galvanised iron light grade pipe, funnel with 40mm bore GI medium grade pipe for watering, wire mesh including concrete pit PCC 1:3:6 type C1, precast RCC 1:2:4 type B1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @ 150 mm centre to centre in both direction and 10mm dia MS handle of suitable size, charchole or coke and salt in alternative layers, including necessary excavation and earth work in any type of soil, all as specified and shown in electrical plate no 3 of SSR part-1 complete all as specified and directed and tested on completion.

Supply, laying and testing cable low tension UG XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 Sqmm 2 core including taking out old unserviceable cable complete all as specified and as directed.

Supply, laying and testing cable low tension UG XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 core including brass compression cable gland, terminal lug, etc complete all as specified and as directed.

M&L for sand cushioning (dry) in trenches for protection of UG cables (below, above and around the UG cable laid in trenches) of 23cm spread thick ness and consolidated (punned) upto 18cm thicknesscomplete all as specified and as directed. Note : For the purpose of payment, punned thick-ness of sand cushioning only shall be measured and paid for.

S&F for sub-class B brick, well burnt, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG Cable protection complete all as specified and as directed.

S&F for ceiling fan, BEE 5 star rated, 1200mm sweep, complete with electronic type fan regulator and accessories 230V complete all as specified and as directed.

Fair cutting straight or racking cutting not exceeding 10 cm width or girth on exposed surfaces of brick work such as in splays, chamfers, etc. including rubbed finish and waste complete all as specified and as directed.

M&L for overhouling of DG Set by opening engine head assembly and taking out piston with ring complete set, carrying out necessary cleaning work including all machine work required for smooth running of DG set of size 250 KVA and reassembling after carrying out necessary repair replacement, fixing only new parts by taking out unserviceable part and testing complete for satisfactory working complete all as specified and as directed. Note : spare parts replaced shall be measured and paid separately under relevant items.

Supply only valve pair inlet & Exhaust for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only valve seat inlet for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only valve seat exhaust for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only valve guide for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only valve seal for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Cylindrical Head Gasket for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Liner with O Ring for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Piston for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Piston Ring for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only CR Bearing piston Stud for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only set of copper washer for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only set of Hose for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only set of Gasket for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Air filter primary element for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Air filter Secondry element for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Cylinder head bolt for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Turbo charger for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only CR Bearing bolt for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Filter element with O ring for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Self starter with O ring for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Lub Oil filter for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Lub Oil 20 ltr for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Lub Oil 10 ltr for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only PM Kit for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Fuel pipe Set for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Feed Pump for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Water pump Pump for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Lube oil Sensor LLOP for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Electrical Governor for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Excuater for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

Supply only Solenoid switch for Kirloskar engine to be incorporated as and when required for 250 KVA DG Set complete all as specified and as directed.

S&F for compressor seal unit of suitable capacity/model for 1.5 /2.0 TR split type AC, ISI marked after necessary repair complete all as specified and as directed.

M&L for comprehensive maint of Air Compressor which includes the following works:- (a) Checking of V belt and repair and replace it (b) Oil, Greasing of bearing of moters and shaft c) Checking of non return valve of compressor and if damage repair it. d) Tighting and cheking of panelwiring with proper thimble (e) Painting of Air compressor with with synthetic enamel paint , one coat after cleaning scrubing the surfaces incl wrirting by paint the capacity , marking of fuel level indicator etc complete as directed by Engineer in charge. Note : (i)Rate Includes for writing in White Paint Date of Cleaning and capacity. (ii) Parts are measured and Paid separately.

M&L for disconnecting for removing the 10 HP Air compressor motor of any make and model type from air compressor and foundation base frame , by disconnecting elecgtrical connecitons, taking it to workshop for repair, removing burn out winding wire complete , rewinding the stator with same guage and type of insullation copper conductor winding wire and insullation sheets , applying isnulating varinish over the complete winding , drying up by heaeting , assembling back the stator inlcuding replacing of nuts, bolts , studs, gasket packing , locking pin , terminal blocks and terminal bolts and misc accessories and hardware required for motor functional both end bearings (labour only) with same size and make complete all as specified and as directed.

S&F for V Belt suitable for Air compressor to motermain drive Pully complete all as specified and as directed.

S&F for high pressure seamless stainless pipe of 16 mm(OD) suitable for distribution of compressed air in hanger as per user requirement including all fittings complete all as specified and as directed.

S&F for high pressure seamless stainless pipe of 18 mm(OD) suitable for distribution of compressed air in hanger as per user requirement including all fittings complete all as specified and as directed.

S&F for head gas ket complete all as specified and as directed.

S&F for piston ring complete all as specified and as directed.

S&F for connecting rod complete all as specified and as directed.

S&F oil seal complete all as specified and as directed.

M&L for servicing of 5 KVA ,380 V online UPS by servicing of all parts, making all electrical connections ,applying petrolium jelly to battery terminals repair / replacementof battery leads ,repairs of parts make the UPS functional complete all as specified and as directed.

S&F in repair sealed lead acid battery of 12 Volt 42 H complete all as specified and as directed.

FREEZCON

NChetia and Sons Trading

boruah construction

R D Enterprises

Bimal Trading Company

AFTAB ENTERPRISES

MAZUMDAR ENTERPRISE