SPECIAL REPAIR TO BUILDING NO P 157 AT NDA KHADAKWASLA

Amount

Dismantling of single layer of manglore pattern or similar tiles in roofing

Dismantling of wooden boarding of any description fixed in any position with nails(weather boarding/ eaves board) all as specified

Dismantling timber scantlings 40 sqcm & over in section, in any position work.

Dismantling timber scantling in fillets rails, rafter, purlins etc n. exc 40 Sqcm in section

Dismantling of battens for tiles, shingles etc., of any size and description spaced exc 15 cm including tiling fillets

Dismantling wrought iron or mild steel work of any description not other wise provided for

S&F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick plain.curve, zigzag any pattern of an coloure having tensile strength of 550Mpa as in roof covering fixed with self tapping screws or fixed with L type of J type hook bolts all as specified

S&F for pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any coloure having tensile strength of 550Mpa as inridge,valley or hip ridge etc. fixed with self tapping screws complete all as specified

M&L for mild steel rolled section connected with each other with welding (angle,tee,channel, beam, hollow sections, tubulur steel etc) as in main and cross sections fixed with angle cleats or other connecting plates conforming to GdeFe-410- W(Gde- E-250) quality- B complete all as specified and directed

M&L for providing cement concrete Type B1, (1:2:4) (Using 20 mm graded stone aggregate) in between roof sheet and wall and like complete all as specified and directed

Dismantling of AC Ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets

M&L for 4mm thick non asbestos cement plain sheet 600 x 600 for ceiling over & including Powder coated aluminium grid work 610 x 610 mm with using 36.5mmx23.5mmx 1.5mm thick main tee, 23.5 x23.5mm x1.28mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 610x610mm on RCC slopping complete all as specified.

Dismantalling floor hearth and wall tiling including cement mortar bedding but not backing complete all as specified

Demolition of cement concrete in ground floors and paving n. exc 15 cm thickness (above or below ground level).

M&L for vitrified tiles flooring 10mm thick (square/rectangular) polished laying in design pattern (Pattern approved by GE) area of each tiles not ecx 0.36 Sqm in floor etc laid bedded over & including screed 20mm thick CM (1:6) bedding & pointed in white/coloured cement to match coloured tiles etc complete all as directed.

M&L for vitrified tiles 10mm thick and 10 cm height as in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match tiles including 10 mm thick backing plaster in CM (1:4) complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 sqm but n. exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:6) bedding complete all as specified and directed

M&L for ceramic tiles as in vertical surfaces of size 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed incl 10 mm thick backing plaster in CM (1:4) complete all as specified and directed

M&L for 50 mm thick PCC (1:4:8) type D-2 (Using 40mm graded stone aggregates) as in sub base

Dismantling of wooden kitchen cabinat and cupboard fixed in any position

M&L for 18 mm thick ply wood grade BWR, type BB fixed with screws to timber frame work for kitchen cabinat,cupboard etc.

M&L for 12 mm thick ply wood grade BWR, type BB fixed with screws to timber frame work for kitchen cabinat,cupboard etc.

M&L for 0.9 mm thick decorative laminate type I, of surface finish, colour and pattern as approved , fixed with approved adhesive as per manufacturer,s instructions.

S&F for conitinious piano hinges,mild steel bright finish or electrogalvanised ,30mm wide of flaps

S&F for 50 mm size butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed type E-II

S&F ball catches with 8 mm dia steel ball, and brass body and strikoing plate including letting in and fixed

S&F for 100 mm long Stainless steel handle ,casst type polished bright for cupboard,cabinate ,etc.

M&L for first class hardwood plain fillets, square, rectangular or tringular in section ,clean sawn, secured with nails or brads sectional area not exc 3 sqcm

S&F telescopic sliders with ball bearings, as in kitchen shelves, 45 mm wide, 450 mm long, fully extendable to 900 mm, fixed to plywood with screws, complete all as specified and directed.

M&L for french polishing on wooden surfaces of any description, including cleaning and preparing the surfaces including a coat of wooden filler on new works with two or more coats

Taking down chowakat with shutters of any description n exe 1.5 sqm each

Taking down chowakat with shutters of any description exe 1.5 sqm but not exc 4.0 Sqm each

Taking down shutters exe 1 sqm n exc 2 sqm each

Taking down shutters exe 2.0 sqm each

M&L for second class hardwood plain solid straight chowkhats and frames, wrought, framed rebated of the solid rounded or chamferred put together with the pinned and joints.

S&F factory made IInd class hard wood plain framed panel shutter (two panel), with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003(Part I), kiln seasoned and chemically pressure treated and thickness of shutter is 35 mm.

S&F second class hard wood glazed and skeleton shutter open rebated and prepared to receive glass gauze, etc. ( without sash bars) edges of framing plain, chamferred or rounded fitted with cut and mitered bends for securing glass etc size of members of shutters as specified in as Part I Sec 8 Cl 8.20 (a), 35mm thick

S&F 40 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides & both face is covered with decorative face veneer with lipping /frame to match incl 100mm motice latch with two levers (vertical type) , mild steel body complete all as specified and directed

S&F aluminium powder coated three track sliding window with 5.5 mm thick tinted glass shutters and stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed (a) Bottom frame - 20620, (b) Top frame and vertical - 20621 (c) Handle (side) - 20606, (d) Shutter inter lock - 20724, (e) Shutter top & bottom - 20844 & (f) glazing clip -19352

S&F mild steel frame work such as grills, gratings,hold fast etc, with ends of bars shouldered and or riveted, or forged into spikes; framed guard bars barred iron doors ladders framed balusers walk ways railing etc and similar work conforming to Fe.290Gde-E-165

S&F stainless steel wire cloth 0.36 mm nominal dia of wire average width of apperture 1.40 mm and fixed in steel window with aluminium clip / wooden beading /stainless steel nut bolt complete all as specified and directed

S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification all as directed

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with particle board core with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back face complete all as per specification and directed

S&F first class hardwood beading straight for any type of shutter, fixed complete with nails or glue incl mitered etc complete all as specified

S&F butt hinges, medium weight, cold rolled mild steel , size of hinges 100mm and fixed to wooden surface

S&F for 150mm long stainless steel barrel tower bolt , stove enamelled black ,with bright bolt and fixed complete

S&F extruded aluminium alloy handle fabricated type annodised size of handle 100mm size

S&F 300 mm long mild steel sliding door bolt , plate type stove enamelled black , with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate and fixed.

S&F 140 mm overall length of cover plate floor door stopper of aluminium ally body and tongue anodised, with hard drawn steel spring fixed in floors complete all as directed

S&F 20mm dia MSCP curtain rod with fixing fancy brackets, stops,rollers etc. complete all as per directed

Dismantling stone slab of any description or thickness in floors, approns etc

M&L for 20 mm to 25mm thick hand/machine cut polished kota stone slab as in tread and landing etc length of slab equal to length of thread fixed after and including 15mm thick screed bed in CM (1:6), jointed with grey cement slurry mixed with pigment to matched the shade of the slab including rubbing and mirror polishing complete, complete all as directed.

M&L for 20 mm to 25mm thick machine cut kota stone slab as in riser of steps,skirting,dado etc length of slab equal to length of riser of steps fixed after and including 10mm thick backing coat in CM (1:4), jointed with grey cement slurry mixed with pigment to matched the shade of the slab including rubbing and mirror polidhing complete, all as directed

M&L for 25mm to 40mm thick unpolished cuduppah stone slab as in cooking platform below granite stone and like incl necessary jointing and pointing and making good to disturbed surface complete all as specified

M&L for 25mm to 40mm thick unpolished cuduppah stone slab as in vertical support for cooking platform and like incl necessary jointing and pointing and making good to disturbed surface complete all as specified

M&L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) as in cooking platform , wash basin platform and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over cement slurry 15 mm thick in CM (1:6) complete all as specified and directed

M&L for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) as in vertical surface (fasia ect.) and like complete all as directed.

Labour only for chamferring and rounding the straight cut edges of stone slab such as in steps , cooking platform and other similar situations complete all as specified

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, wahers and wastes incl bedding in cement mortar on the dwarf wall or incl fixing cantilever brackets and incl all necessay fitting , connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330 mm x 160 mm

S&F for in repairs Stainless steel plate utensil rack of size 900 X 600 X 1mm thick, 30cm width and fixed to wall surface with necessary bolts complete all as specified (Make : HINDUSTAN / NIRALI)

S&F in repairs vitreous china ware wash basin white, flat back size 550 X 400mm including 32 mm CP waste coupling, chain and plug, waste fittings, union and waste pipe 32mm dia of required length and all necessary inlet, out let PVC connections 600 mm complete all as directed.

S&F in repairs Vitreous china wash down water closet (Pedestal pattern) with P or S trap , white in colour including fixing bolts, connection to drain and to flushing pipe with & including low level PVC valve less symphonic action type flushing cistern of 10ltrs capacity white in colour with inlet, ball valve float and PVC flush pipe 32mm dia with white seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or hinging device complete all as directed.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with long screwed shanks and fly nuts(Make :Jauqar Cat No.FLR-5015)

S&F in repairs bib taps cast copper alloy chromium plated fancy type with crutch or butter fly handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia

S&F in repairs two way bib cock cast copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup (Make : Jaquar Cart Part No CAN-FLR -5041 N)

S&F in repairs angular stop cock cast copper alloy fancy type screwed down high pressure with cruntch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shunk and cup (concealed type)

S&F in repairs shower rose with arm,15 mm dia bore, 450 mm long with 90 degree bend for rain showers. (Make:-Jaquar cat No. SHA- 479L450)

S&F in repairs hand shower (health faucet) with 8 mm dia, 1 mtr long flexible tube and wall hook (Make : Jaquar Cat No. ALD-CHR 593)

S&F in repairs, wall mixture brass CP for mixing hot and cold water with connection to overhead shower with 115 mm long bend pipe and wall flange, screwed down for iron pipe and fixed for 15mm bore of pipe. (Make - JAQUAR Cat No FLR- 5273 UPR )

S&F bathroom cabinet of size 450 mm X 300mm with door and shelves and mirror in front side of door and fixed to wall complete with washer

M&L for providing sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plates brackets, guard and railing 60cm long all as directed

S&F in repairs, Corner glass shelf (with back) CP (Make : Jaquar Cart Part No ACN-1173) complete all as specified .

S&F in repairs tubular towel rail 20mm dia 'D' type 60cm long of brass chromium plated complete all as specified

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed

Refixing old steel tubing 15 mm bore pipes and connections in new or old positions etc complete all as directed.

S&F 15 mm bore tube medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed

Refixing old steel tubing 20 mm bore pipes and connections in new or old positions (walls, ceiling, floors etc) complete all as directed.

S&F 20 mm bore tube medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

Taking down of 75 mm to 100 mm dia CI or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified

S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified and directed

S&F for 110mm dia PVC (SWR) bends any radius with access door complete all as specified and directed

S&F for 110mm dia PVC (SWR) junction single(single T) complete all as specified and directed

S&F for 110mm dia PVC (SWR) vent cowl complete all as specified and directed

S&F for 110mm dia PVC (SWR) branch piece, single(single Y) equal or unequal complete all as specified and directed

S&F for 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified and directed

S&F for 75mm dia PVC (SWR) bends any radius with access door complete all as specified and directed

M&L in repairs 75 mm dia PVC floor trap with grating including jointing with solvent cement concrete type B-1 (1:2:4) complete all as specified and directed

M&L for 100 mm dia cast iron Nahani trap, with grating including jointing cement concrete type B-1 (1:2:4) complete all as specified and directed

M&L for cutting chases, pinning in making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades shelves, lintlesetc and cutting chases for concealed water tubing and making good cutting not exc 10 cm girth as in stone walls complete all as directed

M&L for 25mm to 30mm thick thick rough dressed sahabad stone slab flooring bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) incl 15 mm thick screed bed complete all as specified and directed

Taking down cement plaster of any description including racking out joints hacking for key and scrubbing down with water to remove dust etc complete all as specified.

M&L for rendering 10mm thick cement plaster in CM (1:6) surface finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick on ceilings concrete surface in cement mortar (1:4) finished fair and even without using extra cement complete all as directed.

M&L for rendering 15mm thick cement plaster in CM( 1:6)on block/stone walling surface finished even and smooth without using extra cement upto 20m height complete all as specified .

Dubbing out average 15mm thick on irregular face of walls (when specificially ordered in writing) in CM (1:4) upto 20 m height complete all as specified

Raking or cutting out Joints and decayed mortor etc ,washing the joints and keeping the surface to be pointed wet for 2 days prior to re-pointing in random rubble or polygonal rubble uncoursed or brought up to courses work built in cement mortor etc upto three storyed bldg or 20m height complete all as directed.

M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto courses in CM (1:4) upto and including height 20m. Complete all as directed. Note : Rates all as included for scafollding, shuttering, ladder etc

M&L for preparation of newly plastered/concrete wall surface and applying two coats of cement base paint over a coat of primer .

M&L for preparation newly plastered surfase of wall and applying two coats of OBD over a coat of primer including 3mm thick wall care putty complete all as specified

M&L for complete removel of existing treatment on old plastered surface of wall and applying two coats of OBD over a coat of primer including 3mm thick wall care putty complete all as specified

M&L for preparation newly plastered surface of ceiling and applying two coat of OBD over a coat of primer including 3mm thick wall care putty, complete all as specified.

M&L for preparation of new wooden surfaces of any description exc 10cm in width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as directed.

M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer complete all as directed

Dismantling water tanks of capacity exc 500 & n. exc 1000 ltrs and removing to store complete all as specified and directed

S&F 1000 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layer, ISI marked hoisted and fixed in position complete all as specified and directed

S&F in repairs 20 mm dia gate valves cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified

Excavation in trenches, n. exc 1.50 mtr wide and n. exc 1.5m in depth for foundation etc n. exc 10 Sqm on plan and n. exc 1.5m in depth and getting out in hard/dense soil

M&L for PCC (1:4:8) type D-2 (Using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia PVC(SWR) pipe complete all as specified & directed.

Demolition and breacking up 150 mm bore drain pipes (SWG,AC or RCC pipes) set in CM

M&L for PVC(SWR) 150mm pipes single socketed ,in length with rubber ring joints laid in trenches or in floors

Demolition of brick or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facing dressed stone work and pre-cast concrete articles.

M&L for precast cement concrete block masonry with solid block, type C-1,(1:3:6) mix (Using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

Returning, filling including, spreading, leveling, watering and well ramming in layers n.exc 25cm.

Removal of surplus soil to a distance n.exc 50mtr and deposited above directed at a level n.exc. 1.5 m where the starting point.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D-2 (Using 40 mm graded stone aggregate) as in sub base .

M&L for 40 mm thick PCC (1:2:4) type B-1 (Using 20 mm graded stone aggregate) as in top layer finishing Course including spike rolling.

S&F for glossy finished chequered cement concrete tiles 30cmx30cmx30mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors complete all as directed

M&L for PCC (1:3:6) type C-2 as in plinth protection & finishing the surface even & smooth (witout using extra cement ), 75 mm thick complete all as specified & directed.

Taking down unserviceable sub main wiring twin core (two single core) any size with teak wood battens/Casing capping/PVC Conduit/ and making good disturbed surface complete.

M&L for sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and copper cable 4 sqmm continuous earth wire complete all as specified and directed (Two runs of 04Sqmm cable with 01 run of 04 Sqmm earth wire along with casing caping shall be measured as one RM)

M&L for sub main wiring with two single core PVC insulated FRLSH cables with stranded copper conductors 6 Sqmm , 1100 Volts grade in and including PVC conduit medium grade not less than 25 mm complete with accessories and copper cable 6 sqmm continuous earth wire complete all as specified and directed (Two runs of 06 Sqmm cable with 01 run of 6 Sqmm earth wire along with PVC conduit shall be measured as one RM)

S&F sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as specified.

Taking down carefully copper/aluminium point wiring (light/fan/socket) including all accessories wire, casing caping/conduit, screws etc and making good the disturbed surfaces all as specified

M&L for point wiring with 1.5 sq mm copper conductor FRLSH (multistrand) PVC insulated ISI marked unsheathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including modular PVC box with cover plate suitable for modular type switches, sockets, fan regulator etc for One light/Fan point controlled by one way switch 6 Amps 240 volts

Ditto all as per item No. 127 above but for one 3 pin socket outlet, 5/6 Amps, independent

Ditto all as per item No. 127 above but for one 3 pin socket outlet, 5/6 Amps on the same board with other switches

Ditto all as per item No. 127 above but for one 3 pin socket outlet , 15/16 amps on independent board with cable 4 Sqmm and 4 sqmm as earth wire

Ditto all as per item No. 127 above but for one bell/ buzzer point controlled by one push button on independent board with cables 1.5 sq.mm size

S&F modular switch piano type 10 amps one way one module. Make - Roma/Vinay Adora

S&F modular Socket with safety shutter, 10 A - 2/3 pin combined 2 module. Make - Roma/Vinay Adora

M&L for modular Switch with neon indicator 20 A, one way, 1 module. Make - Roma/Vinay Adora

M&L for modular Socket (Heavy Duty) 10/20 A with safety shutter, 6 pin, 2 module. Make - Roma/Vinay Adora

M&L for modular bell push with neon indicator, 10 A, 1 module. Make - Roma/Vinay Adora

S&F modular Fan step regulator, 2 module. Make - Roma/Vinay Adora

M&L in replacement of door bell AC 230 volts single phase ding dong type all as specified and directed. Make:Anchor/Vinay

S&F ceiling rose surface shall comply with IS :371-1979 Bakelite 60x 25 mm two to three terminals plates and of outside diameter not less than 63.5mm.

S&F polycarbonate angle holder retrofit type suitable for CFL/LED bulb of B-22 base all as specified and directed.

S&F LED tube light with diffused optics ultra bright LED tube light 18/20watt with high efficiency,integrated aluminum heat sink complete all as specified.

S&F in replacement 1x18/20W,230V surface and wall mounted batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified .

S&F 1x10 watt, 230 V surface and wall mounted LED batten (for mirror) including connecting up with twin core twisted flexible copper cable from ceiling rose to fitting all complete as specified and directed. Make: Luker/Philips/Havells

S&F in replacement Decorative wall mounting brushed nickel fixture suitable for B22 base bulb upto 14 watt including 01x10 W LED bulb (warm white) and connecting up with twin core twisted flexible copper conductor cable from ceiling rose complete all as specified. Make:Havells FLORETINE WL 1LS B22 SS or equivalent in Philips/Jaquar

S&F in replacement 1x10 watt,230V surface mounted LED downlight with white powder coated polycarbonate housing and pressure die-cast heat sink having high efficiency, including connecting up with twin core twisted flexible copper condctor cable from ceiling rose complete all as specified . Make - Havells Cat part No INTEGRANEOSURFACELS10WLED840S / Luker LBKRDSL10 / Philips

Taking down the ceiling fan carefully and cleaning/Servicing the fan if any repairs/replacing of parts required complete including painting the fan with enamel spray paint white coloured and fixing back the fan with fixing accessoires required at site.

Taking down the Exhaust fan carefully and cleaning/Servicing the fan if any repairs/replacing of parts required complete including painting the fan with enamel spray paint Grey colored and fixing back the fan with fixing accessoires required at site.

S&F MCB DB 12 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper/aluminium cable lugs with suitable size for incoming and outgoing.

S&F MCB DP 40 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing.

S&F MCB DP 63 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper/aluminium cable lugs with suitable size for incoming and outgoing.

S&F in replacement factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB ) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified (Make/Model of VTPN DB : Legrand/L&T/C&S) Note:MCBs/ MCCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F MCCB with rating of 100 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc all as specified.

S&F in replacement LED Building Security Light/Street Light fiitting 30 W,IP-65 protection made up of die cast aluminium housing with high power LED as lighting source complete fixing with GI bracket made out of 25 mm bore GI pipe light grade 1.2 Mtr long bend to shape and fixed to pole/wall with necessary MS clamp accessories complete all as specified and directed by Engr-in-charge. Make:Havells ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC/ Luker LSTE-30/ Philips

S&F electrical meter box compartmentalized design suitable for four energy meter, wall mounted type, weather proof fabricated out of not less than 2.0 mm thick CRCA sheet, powder coated in siemens grey colour, double door. The enclosure shall be front openable with locking arrangement and provided with 5 mm thick bakellite sheet for mounting the energy meter and MCB DB. The enclosure shall be provided with suitable size PVC cable glands for incoming and outgoing cables/wires. The overall size of the meter box shall not be less than 600 x 600 x 300 mm complete with all accessories prewired twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with solid aluminium conductor of size 25 sqmm 3.5 core

Excavation in trenches in hard/dense soil n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed

Excavation in trenches in soft/dis integrated rock n exc 1.5m wide and n.exc 1.5m in depth and getting out complete all as specified and directed

Returning filling in including spreading leveling watering and well ramming in layers n.exc 25 cm complete all as specified and directed

Removing excavated surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5 mtr above starting point complete all as specified and directed

M&L for laying of half round reinforced concrete pipe, of dia 150 mm, half round for bottom and half round for top and before laying excavated area shall be leveled. complete all specified and directed. Note : 01 Half round top and 01 half round bottom together will be considered as one running meter. Make as per sample.

M&L for cutting of existing road/ hard standing by providing suitable T&P to make suitable size bore for fixing 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed

S&F GI tubing medium grade 40 mm dia ISI marked with all fittings laid in trenches and fixed pole by flat iron clamps, nut,bolt,washers suitable size complete all as specified and directed at size.

Taking down existing service connection of any type with all acessories complete.

Mehta and Co.

M/S OMSAI ENTERPRISES