REPAIR/MAINT OF FIRE EQUIPMENT, FIRE ALARM, FIRE HYDRANT AND PIPE LINES AT AF STN TUGHLAKABAD UNDER GE (AF) TUGHLAKABAD

Amount

Supply, fixing, installation and testing in replacement of analogue addressable smoke sensor having removable high performace chamber with twin fire LED's allow 360 degree vewing lock mechanism (sensor to base), variable sensitivity , electronically addressed, approved by LPCB, EN 54 approved complete all as specified and as directed. Make : Ceasefire/Hochiki/LST/Agni

Supply, fixing installation,testing and commissoning in replacement of analogue addressable manual call points ESP analogue addressable protocol having status LED for alarming and standby mode, electronically addressed approved by LPCB, EN-54 approved complete all as specified and as directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of analogue addressable dual input module which allows 2 independently controlled change over relays, relays operated at 30 V DC at 1 Amps having auxiliary monitored input, followed by ESP analogue addressable protocol, electronically addressed, approved by LPCB, EN-54 complete all as specified and directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of analogue addressable dual relay controller which allows 2 independently controlled change over relays, relays operated at 30V DC at 1 Amps having auxiliary monitored input, followed by ESP analogue addressable protocol, electronically addressed, approved, by LPCB. EN-54 approved complete all as specified and directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of microprocessor based 8 Zone conventional fire alarm control panel robustly designed and easy to operate, fully compliant with and tested to BS EN 54-2 and BS EN 54-4, compatible for use on BS5839, Part 1, 2002 installation, 2 wire repeaters and ancillary boards, fully programmable using simple menu options, simple, single board construciton, installer friendly, compatible with Hochiki, conventional range of devices, two monitored sounder outputs, 3 Amp power supply, auxiliary power output, The control must be EN 54 approved complete all as specified and as directed by Engr-in-Charge Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of microprocessor based 4 Zone conventional fire alarm control panel robustly designed and easy to operate, fully compliant with and tested to BS EN 54-2 and BS EN 54-4, Compatible for use on BS5839, Part 1, 2002 installation, 2 wire repeaters and ancillary boards, fully programmable using simple menu options, simple, single board construciton, installer friendly, compatible with Hochiki, conventional range of devices, two monitored sounder outputs, 3 Amp power supply, auxiliary power output, The control must be EN 54 approved complete all as specified and directed. Make : Ceasefire/Honeywell/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of microprocessor based 2 Zone conventional fire alarm control panel robustly designed and easy to operate, fully complaint with and tested to BS EN 54-2 and BS EN 54-4, Compatible for use on BS5839, Part 1, 2002 installation, 2 wire repeaters and ancillary boards, fully programmable using simple menu options, simple single board construciton, installer friendly, compatible with Hochiki, conventional range of devices, two monitored sounder outputs, 3 Amp power supply, auxiliary power output, The control must be EN 54 approved complete all as specified and directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of (multi criteria) type detector with combination of both heat and smoke detection arrangement of the same make as of fire alarm control panel. Detector should have a third terminal to provide an integral remote indicator output, removable high performance chamber, remote indicator output, wide voltage range (9.5 to 30V d.c) low profile design with one piece outer cover, twin fire LED's allow 360 degree viewing, range of mounting bases, approved by LPCB complete all as specified and directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, fixing installation and testing and commissoning in replacement of conventional manual call point of the same make as of fire control panel, based upon the industry standard KAC world series housing and features easy to install, push fit wiring terminals.The unit can support either a Frangible glass element or a 'Non frangible plastic' element. Approved to EN54-11 : 2001 terminals can accommodate upto a 2.5mm solid conductor. approved by LPCB complete all as specified and directed. Make : Ceasefire/Hochiki/LTS/Agni

Supply, laying and fixing in replacement on wall or in trench/ducts, 2 core 1.5 sqmm armoured cable copper conductor including steel saddles, screw for fixing of cable on wall and ducts in and including PVC heavy duty conduit ISI marked fixing with saddles of size 25mm dia complete all as specified and directed. Make : Havells/Finolex/Plaza

Supply and laying in replacement of 2 core 1.5 sqmm armoured cable copper conductor into existing conduit (concealed type) complete all as specified and directed. Make : Havells/Finolex/Plaza

Supply & fixing in replacement of battery 6 Volts 7 AH of approved make suitable for FACP panel complete all as specified and directed.

Supply & fixing in replacement of PCB suitable for FACP circuit incl wiring kit of existing capacity and of Make Hochiki complete all as specified and as directed.

Labour only tracing out the fault and functiong the microprocessor based upto 8 Zone conventional fire alarm control system, reassembling and testing complete all as specified and directed. Note :- (i) The fault shall be carry out by highly skilled trades man only and charges for new items shall not deemed to be included under this item.

Maintanenane/repair/servicing of fire system at various location in 7 BRD as required viz, fire panel, smoke detecter, beam detecter, wall sounder, all cable connection, manual call bell point and replacement of unserviceable parts with new parts re-assembling, connecting, commissioning and testing complete all as specified and directed. Note:- New parts if any required shall be measured and paid separately under respective item of this schedule.

Supply & fixing in replacement fire hydrant landing valve type B ( double head outlet) of 63 mm dia conforming to IS 13039-1991 along with 2 Nos cast iron hand wheel , 2 Nos female instantaneous outlet, 2 Nos ABS blank cap and chain complete all as specified and directed. Make: Padmini/DSS/Newage.

Supply & fixing in replacement fire hydrant landing valve type B ( single head outlet) of 63 mm dia conforming to IS 13039-1991 along with 1 Nos cost iron hand wheel , 1 Nos female Instantaneous outlet, 1 Nos ABS blank cap and chain complete all as specified and directed. Make: Padmini/DSS/Newage.

Supply and fixing in replacement hose box wall mounting type for keeping 2 Nos hose pipe of length 15 meter each, branch pipe.nozzle, coupling etc made out of 16 gauge mild steel sheet size 800mm x 600mm x 250mm , acrylic fronted double door with lock , 2 keys and a break glass recess for Key, painted fire red.Make: Padmini/DSS/Newage.

Supply and fixing in replacement branch pipe gun metal 63mm instantaneous inlet, made threaded outlet, 15mm bore nozzle long conforming to IS 903 complete all as specified and as directed. Make: Padmini/DSS/Newage.

Supply and fixing in replacement 63 mm dia 15 meter long CP hose conforming to IS 636 complete with male and female coupling conforming to IS 903 complete all as specified and as directed. Make: Padmini/DSS/Newage.

Supply and fixing in replacement fire hose reel drum 30 m long, as per IS : 3844-1989 with all accessories including gun metal valve 15 mm with nozzzle and fixed on wall complete all as specified and as directed. Make: Padmini/DSS/Newage

Taking out heavy duty MS duct cover 1.2x0.7x0.08 weighing 250 kg for cleaning of mud/stone whichever is there and refixing the duct cover after taking out pipe line and refixing the same of any size and capacity in the duct complete all as specified and directed.

M&L for boring holes 2 mtr deep (trench less) in soil for under-reamed piles, 250mm dia pipe, getting out and disposal of spoil to a distance not exceeding 50 mtr and making good distrubed surface complete all as specified and directed.

M&L for dismantling joints of flanged pipes in position including removing old gasket, nut ,bolts etc upto size 150mm dia complete all as specified and directed.

M&L for joints of flanged pipes in position including new rubber or fiber board gasket, nut ,bolts washers etc upto size 150mm dia complete all as specified and directed.

Taking up unserviceable CI water main(incl all fitting) with flanged ends incl disconnecting pipes and fittings complete of size 150 mm bore for laying /rerouting of serviceable pipe after cleaning complete all as specified and directed.

Material and labour for laying of CI pipes of size 150 mm bore with flanged ends centrifugally cast class A in any length laid in trenches/on surface/ over masonary pillar and connection to old or new position complete all as specified and directed. Make- Jindal/ Kesoram/Electro steel Note: CI fitting /gasket joint will be measured and paid seperately.

Material and labour for laying of CI pipes of size 100 mm bore with flanged ends centrifugally cast class A in any length laid in trenches/on surface/ over masonary pillar and connection to old or new position complete all as specified and directed. Make- Jindal/ Kesoram/Electro steel Note: CI fitting /gasket joint will be measured and paid seperately all the dismanted / demolished /taking down material shall be removed from site.

Supply and laying in replacement of steel water tubing medium grade in trenches/wall/floor with all fittings, connections as required at site of size 50 mm bore complete all as specified and directed. Make:- Jindal/TATA/BST

Supply and laying in replacement of steel water tubing medium grade in trenches/wall/floor with all fittings, connections as required at site of size 80 mm bore complete all as specified and directed. Make:- Jindal/TATA/BST

S&F in replacement CI special like Bends. Tapers. Tee pieces (single & double branch) any type and angle/radius and straight connecting pieces but all ends flanged of the following size upto 150 mm dia complete all as specified and directed. Note:- Gasket, nut bolt & washers for fitting shall be measured and paid separately.

Suply and fixing in replacement cast iron NRV flanged end of size 150 mm dia with all fitting and accessories including taking down old unserviceable NRV complete all as specified and directed. Make:Zoloto/Kirloskar/Kartar.

Supply & fixing in replacement Cast Iron sluice valve of size 80 mm bore class PN-1.6 IS : 14846 with SS spindle, both ends flanged with holes, provision of nuts, bolts, washers, rubber gasket etc. with CI wheel, fixed to CI water mains , and including taking down old unserviceable Sluice valve complete all as specified and directed. Make:Zoloto/Kirloskar/Kartar.

All as per item N0-36 here-in-before but 150 mm dia bore.

M&L for opening of fire Jokey pump type 30 LPS for repair and replacement of following unserviceable parts including re-fixing in position after repairing,testing and commissioning complete all as specified and directed. (a) Replacement of gun metal impeller. -01 Nos (b)Replacement of gun metal bush -02 Nos (c) Replacement of ball bearing.Make: SKF - 02 Nos. (d) Replacement of oil seal -01 Nos. (e) Replacement of gland -01 Job

M&L for rewinding of burnt Jokey pump motor of capacity upto 30HP, 30 LPS, 3 phase ,415 V, 50 Hz of any make with copper conductor of the same specification as per old one after dismantling / cutting out burnt windings from stator assembly, cleaning slots properly complete with insulating slots packing, sleeves, papers & reassembling stator and rotor after replacement of worn out spares/matching works including painting with two coats of synthetic enamel paint over a coat of red oxide primer after preparation of motor external surface and water proof jointing for cable 3 core, with replacement of oil seal, sand guard, bolt gasket, cable packing ring, circlip, bearing bush upper & lower etc complete all as specified and as directed.

M&L in replacement for MCCB 4 pole 250 Amps, 36 KA, make- Legrand/Havells cat Part No IHLFHF0250# / L&T/Standard.

M&L in replacement for MCCB 4 pole 400 amps,36 KA, make- Legrand or equivelent of Havells Cat Part No IHLLNFBF0400 / L&T/Standard.

S&F in repair cast iron foot valve of size 150mm dia heavy duty with necessary fixing arrangement like nut , bolts washer packing sheet etc including taking out existing unserviceable footvalve complete all as specified and directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to GI strip 32mm X 6 mm main earthing lead by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt all around earth plate, test point of phosphorous bronze / gun metal of size 75 mmx 75 mm x25 mm, PCC (1:3:6) type C-1 (using 20mm graded black trap/granite/basalt stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm graded black trap/granite/basalt stone aggregate) 40mm thick cover reinforced with 8mm dia TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh, and 40 mm dia GI medium grade earth lead protection pipe, complete all as specified and directed. NOTE : Earth strip and its protection pipe upto and including 7.5 mtr from the top of earth electrode are included under this item and additional earth strip/protection pipe etc. if any required at site shall be measured and paid for separately under appropriate item of Schedule `A’

Disconnecting, taking out, removing old existing unserviceable underground cable and Supplying ,Laying, jointing and testing new XLPE insulated, armoured, heavy duty, aluminum conductor cable 1100 volts grade ,laid in trenches/ducts, floors, fixed to walls etc. complete all as specified and directed of size 3.5 core 35 sqmm. Make :- Havells/Polycab/Gloster/Finolex.

Excavation in trenches not exceeting 1.5 Mtr wide and not exc. 1.5 Mtr in depth and getting out in hard/dense soil for laying cables complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and ramming in layers not exc. 25 cms complete all as specified and directed.

Removing excavated material not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Supply and filling dry river sand in trenches for cable cushioning complete all as specified and directed.

Supply and fixing subclass-B,bricks class designation-75 for cable protection complete all as specified and directed.

M&L for construction of valve chambers with MS cover 3 mm thick of valve pit of size 1200x1200x1200 MM( internal dimensions) including necessary excavation, earth work, 150 mm thick PCC 1:4:8 Type D2 using 40mm graded stone aggregate as in foundation, PCC 1:2:4 Type B1 using 20mm graded stone aggregate in coping, plastering 15 mm thick in cement mortar 1:4, and angle iron frame 50x50x06 mm and locking arrangement including painting with two coat of synthetic enameled paint over a coat of redoxide primer after preparation of surface complete all as specified and directed.

Taking out existing unserviceable MS pipe line of size upto 80 mm bore complete all as specified and directed.

Supply, laying , jointing, welding & testing in replacement of MS pipe ( Heavy duty Class 'C') including fitting as required of following sizes laid in treches or laying on floor for connecting to various accessories and to connect outgoing air pressure main complete all as specified and directed. Note:- MS flange and flange joint complete with jointing material shall deemed to be included in the unit rate of this item

20 mm bore

25 mm bore

80 mm bore

S&F in replacement ball valve brass with iron handle screwed both ends for iron pipe and fixed of following sizes :- Make-Zoloto/Leader/ Castle

dia of pipe 20mm

dia of pipe 25mm

Taking up unserviceable CI water main(incl all fitting) with flanged ends incl disconnecting pipes and fittings complete of size 100 mm bore for laying /rerouting of serviceable pipe after cleaning complete all as specified and directed.