Special repair to building No II-6A (Cooking shed, Dining Room Ration store) at 122 Inf Bn TA (MADRAS) at Calicut under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing including tilting tiles all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

M&L for structural steel work in tubular trusses including special shaped washer, etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 all as specified and directed.

M&L for MS Rolled sections as Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) using Fe 410-w (Gde E -250) quality A all as specified and directed.

Providing, cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding(but not backing),removing serviceable tiles and rubbish off the premises all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L for light shade joint free non-skid rectified ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:3) all as specified and directed.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

M&L for cement concrtet 1:2:4 (nominal mix), type B1 using 20mm graded stone aggregate as in lintels not exc 1.50m span, cills, steps, seismic and other similar bands including necessary form works complete all as specified and directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 27 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

M&L for second class hardwood, panelled shutter 35mm thick (two panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S&F mild steel framed work such as grills gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F 4mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F 75mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F Harrison rails 25mm dia, chromium plated with fixing brackets , stops, rollers etc. all as specified and as directed.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 75mm size fixed with stainless steel screws all as specified.

S&F casement stays 250mm long with hinged joints and two plates with studs complete all as specified and directed.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F Floor door stopper Overall length of cover plate 140mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor etc complete all as directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting all as specified and directed.

M&L for complete removal of existing treatment on surfaces of wall by scrapping down, preparation of surfaces and applying two coats of white wash all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying three coats of white wash all as specified and as directed.

M&L for complete removal of existing treatment on surfaces of wall by scrapping down, preparation of surfaces and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

JEETH CONSTRUCTION

LAKSHMI BUILDERS

B AND H CONSTRUCTIONS