ADDITION/ALTERATION AND REPAIR TO JCOs AND OR MD ACCN AT KS VIHAR, MS VIHAR AND GS VIHAR UNDER GE (S) AKHNOOR

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground floors) complete all as specified and as directed.

Cement concrete type B-0 1:2:4 using 12.5mm graded crushed stone aggregate, 25mm thick as in flooring etc.; finished the surface even & fair, complete all as specified and as directed.

Screed bed or bedding layer of cement mortar 15mm thick, for laying floor finishes in cement 1:4, complete all as specified and as directed.

Non-skid ceramic coloured designer pattern tiles 300mmx300mmx7mm thick in floors etc.; set jointed in neat cement slurry and pointed in white cement or coloured cement to match etc.; complete all as specified and as directed.

Non-skid Ceramic coloured tiles (Joint free) 7mm to 8mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as Item No. 5 above but as in skirting, complete all as directed.

Plain cement concrete (1:3:6), type C-1 (using 20mm graded crushed stone aggregate), 50mm thick, as in plinth protection and providing the joints throughout thickness, filled with mastic filling comprising bitumen 85/25 grade and sand mixture 1:3 by weight, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

10mm thick rendering as in backing coat of tiles in cement mortar 1:4 complete all as specified and as directed.

Glazed ceramic coloured designer pattern tiles 450mm x 300mm x7mm thick on vertical surface such as skirting, Dado etc. set and jointed in white colour cement complete all as specified and as directed.

Granite 20mm thick (table rubbed and polished) in cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust making holes in RCC shelves suitable for gas pipe with round edges where required complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. after that applying brushing neat cement slurry with 3.0 Kg of cement per Sqm to receive to kota stone/floor tile etc.; complete all as specified and as directed.

Machine cut kota stone slab flooring 18mm to 20mm thick over and including 20mm thick cement mortar (1:6) screed bed laid and jointing with grey cement slurry mixed with pigment including rubbing and polishing complete as on stair, shelves etc.; complete all as specified and as directed.

Machine cut kota stone 18mm to 20mm thick as in skirting/dado etc. laid over and including 10mm thick cement mortar (1:4) as back coat and jointing with grey cement slurry mixed with pigment including rubbing and polishing complete all as specified as directed.

Demolition of cement concrete exceeding 15cm thickness but above ground floor as sunken floor complete all as specified and as directed.

Plain cement concrete type E-2, 1:5:10 (using 40mm graded crushed stone aggregate) as in sunken flooring complete all as specified and as directed.

Water proofing treatment to sunken portion of WCs bathroom etc.; by applying cement slurry mixed with acrylic based polymer modified cementations composite compound:- (a) First layer of slurry cement @ 0.488 kg/ Sqm mixed with Acrylic based polymer modified cementations composite compound @ 0.253 kg/Sqm .The layer will be allowed to air cure for 4 hrs. (b) Second layer of slurry of cement @ 0.242 kg /Sqm mixed with Acrylic based polymer modified cementations composite compound @ 0.126 Kg/Sqm . The layer will be allowed to air cure for 4 hrs.

15mm thick rendering on fair face of concrete surface finished even and smooth without using extra cement in cement mortar 1:3 using water proofing compound as per manufacture instruction as in sunken portion of floor complete all as specified. Note: WPC will be measured and paid separately as supply only

PCC (1;2:4) type B-1 using 20mm graded crushed stone aggregate as sides of rounded or chamfered on edges of sunken floor, complete all as specified and as directed.

32mm dia G I pipe bevelled cut at both ends by making hole in walls sunken portion approx. above the RCC slab and ceiling finished the hole with cement mortar (1:2) to match with existing surfaces complete etc.; complete all as specified and as directed.

Grubbing up bushes, tree truck of trunk portion not exceeding 10cm girth including cutting of trees/bushes grown in over wall and roofs digging out roofs and making good damage area of wall/roofs with PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate, complete all as directed.

Preparation of RCC projection chajjas, roof, facia etc.; by necessary scraping, cutting, chiselling, derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but not exceeding 3Kg/Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand and work in patches area not exceeding 5 sqm and thickness RCC member not exceeding 70mm including necessary formwork and applying two coats of finishes to match with the existing surfaces at any height, complete all as specified and as directed. (Note: welded wire mesh shall be measured and paid separately)

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connection s including cleaning for refixing or removal to store 20mm bore complete all as specified and as directed.

Tube 'medium grade' galvanised, with all fitting and fixed complete to walls and ceiling etc.; 15mm bore complete all as specified and as directed.

Tube 'medium grade' galvanised, with all fitting and fixed complete to walls and ceiling etc.; 20mm bore complete all as specified and as directed.

Bib taps, chromium plated, fancy type, cast copper alloy screwed down screwed for iron pipe or for brass ferrule and fixed in repair, 15mm bore complete all as specified and as directed.

Stop valve, CP cast copper alloy fancy type, 15mm bore, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed in repair, complete all as specified and as directed.

Stop valve, CP cast copper alloy fancy type, 20mm dia, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed in repair, complete all as specified and as directed.

All as per Srl item No. 29 above but angle valve 15mm bore.

Brass chromium plated sink mixer for mixing hot and cold water screwed down for iron pipes and fixed in repair, 15mm bore, complete all as specified and as directed.

Brass chromium plated wall mixer for mixing hot and cold water with provision of shower screwed down for iron pipes and fixed in repair, 15mm bore, complete all as specified and as directed.

Fancy type Pillar tap, cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore complete all as specified and as directed.

PVC connection 15mm bore size with PTMT nuts of length 45cm complete all as specified and as directed.

PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets, flush pipe, fixed in repair, 10 litre capacity complete all as specified and as directed.

Brass chromium plated shower rose 125mm fixed in repair complete all as specified and as directed.

Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed in repair 20mm bore complete all as specified and as directed.

Stainless steel sink with draining board made of 1.00mm thick sheet for kitchen with plug, washer waste pipe cast iron cantilever bracket connecting union overall size 915mmx 460mm with bowl size 330mm x 160mm complete all as specified and as directed.

Acrylic shelf 450mm long and 100mm wide fixed over WHB of approved quality as per sample held in GE Office all as directed.

PVC bath room cabinet of size 535 x 483 mm x 110 mm with mirror all as directed.

Stainless steel plate rack of superior quality size 36" x 30" weight not less than 8 kg, fixed in repair, complete all as specified .

Rotational moulded polythene water storage tanks (ISI marked) cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part I, 500 ltr capacity incl dismantling water tanks, tank nipple and removing to store, complete all as specified and as directed.

Vitreous china wash basin, white flat back size 550x400mm excluding taps, waste chain and plug and proclain stopper but including bracket, fixed in repair, complete all as specified and as directed.

Vitreous China squatting pattern Orissa pattern WC size 580mmx440mm white with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and as directed.

Brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges, fixed in repair, complete all as specified and as directed.

40mm dia waste pipe for kitchen sink, complete all as directed.

3mm thick, sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm, each pane, complete all as specified and as directed.

Taking down chowkhat or frame with shutter, without taking off shutter from frame exceeding 1.5 Sqm and not exceeding 4 Sqm, complete all as specified and as directed.

Taking down chowkhat or frame with shutter without taking off shutter from frame not exceeding 1.5sqm each complete all as specified and as directed.

Taking down shutter of any description exceeding 1 sqm but not exc 2 sqm each, complete all as specified and as directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube supplying and fixing in opening as specified and directed.

MS Framed work as in doors or gate, coolers stand of angle or others section etc. confirming to Fe 410-W (Gde -E- 250) quality A complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 125mmx60mm, complete all as specified and as directed.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105mmx60mm, complete all as specified and as directed.

Plain cement concrete M-10 (1:3:6), type C-0, (using 12.50mm graded crushed stone aggregate), as in hold fasts or filling in hollow portion of steel frame, complete all as specified and as directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site, complete all as directed.

40mm thick, Flush shutters, (Factory made) solid core construction, with partical board core and plywood face panels, commercial type on both sides complete all as specified.

Cupboard shutter 20mm thick (style) factory made panel PVC including chowkhat frame made out of m.s tubes 19 gauge for top and bottom rails m.s frame shall be covered with heated moulded plain colour PVC (c) channel having a PVC sheet strip of 10mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side 10mm (5mmx2) thick of 20mm and 20mm cross PVC sheet and as gap insert for top and bottom rail. Panelling for plain colour PVC sheet to be fitted in the m.s frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification and drawing, fixed in repair, complete all as specified and as directed.

Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber framework as in shelves of cupboard etc., fixed in repair, complete all as specified and as directed.

External teak wood lipping, 6mm thick fixed with nails over block board or veneered particle board for cupboard self, complete all as specified and as directed.

Factory made glazed and skeleton shutters open rebated and prepared to receive (glass) gauze (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing gauze (glass) etc.; size of members of shutters 35mm thick, 2nd class hard wood, complete all as specified and as directed.

Aluminium anodised powder coating of any colour frame for doors, windows, ventilators of size 114.30mmx44.45mmx2.42mm thick with one or more rebates including joining cleat for fixing etc.; complete all as specified and as directed.

Aluminium anodised powder coating of any colour window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1No.). hinges type B-21 100mm long (2No.) suitable handle (1No.) complete all as specified

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

Butt hinges, medium weight cold rolled mild steel and fixed 100mm long, complete all as specified and as directed.

Aluminium anodised barrel tower bolts of extruded section and fixed 200mm long, complete all as specified and as directed.

Aluminium handles cast type anodised 150mm long, complete all as specified and as directed.

Brass ordinary rat tail rod pattern spring 300mm long including roller plate complete all as specified and as directed.

Aluminium alloy anodised sliding door with hasp staple(bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 250mm long, complete all as specified and as directed .

Hasp and staple safety type aluminium anodised with mild steel hinges pin including bolt to hinge plate and fixed with screw size 125mm, complete all as specified and as directed.

Preparation of new or previously untreated wood or wooden surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coat of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed .

Floor doors stoppers of aluminium alloy body and tenque anodised with hard drawn steel spring fixed in floor 150mm long, fixed in repair, complete all as specified and as directed.

Epoxy powder coated pelmet rods of mild steel 25 mm with and including pair of fancy type finnals, fixed in repair, complete all as specified and as directed.

Dismantling of old/damaged existing roof treatment along with concrete padding and cleaning all waste and dirt by wire mesh, picking, sweeping and washing down with water to remove dust, etc., and removal of all material out side the cant area, complete all as specified and as directed

Dismantling brick tiles or terracing tiles single layer on roofs, complete all as directed.

10mm thick screed bed, bedding layer for laying floor finishing in cement mortar (1:6) using water proofing compound as per manufacture instruction on roof surface, complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately as supply only.

Water proof treatment roof top with 5 layered APP membrane treatment will be applied as under:- (a) Applying a coat of bituminous primer confirming to IS - 3344 @ 0.40kg/Sqm on the prepared surface. (b) After the primed surface has dried , apply a coat of hot blown 85/25 penetration grade blown bitumen or equivalent viscosity grade blown bitumen ( Penetration of bitumen when tested as per IS 1203 will not be more than 40) conforming to IS 702 @1.20 kg/ Sqm of the surface. (c) Provide APP ( Atactic polypropylene ) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film . Minimum weight of membrane will be 3kg /Sqm . Other properties of APP modified water proofing membrane will be as laid down in MES SSR -I Part 11.43.2.2. APP membrane will be laid minimum end lap of 150 mm and side lap of 75 mm bonded with hot blown bitumen. (d) Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen or equivalent viscosity grade blown bitumen (Penetration of bitumen when tested as per IS 1203 will not be more than 40) / conforming to IS 702 @ 1.20 kg /Sqm and blinded with fine sand in dry condition @ 0.50 Kg/Sqm dusted over the bitumen cost.

M&L for Water proof treatment roof top with 5 layered APP membrane treatment will be applied as under:- (a) Applying a coat of bituminous primer confirming to IS - 3344 @ 0.40kg/Sqm on the prepared surface. (b) after the primed surface has dried , apply a coat of hot blown 85/25 penetration grade blown bitumen or equivalent viscosity grade blown bitumen ( Penetration of bitumen when tested as per IS 1203 will not be more than 40) conforming to IS 702 @1.20 kg/ Sqm of the surface. (c) Provide APP ( Atactic polypropylene ) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film . Minimum weight of membrane will be 3kg /Sqm . Other properties of APP modified water proofing membrane will be as laid down in MES SSR -I Part 11.43.2.2. APP membrane will be laid minimum end lap of 150 mm and side lap of 75 mm bonded with hot blown bitumen. (d) Over the APP membrane apply semi hot blown 85/25 penetration grade bitumen or equivalent viscosity grade blown bitumen (Penetration of bitumen when tested as per IS 1203 will not be more than 40) / conforming to IS 702 @ 1.20 kg /Sqm and blinded with fine sand in dry condition @ 0.50 Kg/Sqm and applying two coats of aluminium paint over a coat of primer, complete all as specified and as directed.

Providing 20mm thick precast PCC tiles jointed & pointed flush in cement mortar (1:6) over 15mm thick bedding layer of cement mortar (1:6) using 5% creosote oil, complete all as specified and as directed.

PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, benching rounded or chamfered on edges, including use of form work complete all as specified and as directed.

Supply only integral waterproofing compound.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved in plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in filling and mass concrete etc.; complete all as specified and as directed.

Framedwork such as grills, gratings, etc.; with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework/ caging of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

150mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Expanded metal weight not exceeding 4 Kg/Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, complete all as specified and as directed.

Mild steel screw bolts having dia of neck 11mm to 15mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5cm long but not exceeding 10cm long complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc.; including raking out joints, hacking for key, scrubbing down with water etc.; complete all as specified and as directed.

10mm thick plastering on other than fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed.

5mm thick plastering on concrete surfaces, finished even and smooth without using extra cement in cement mortar (1:3) on ceiling, complete all as specified and as directed.

15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in cement mortar 1:4 using water proofing compound as per manufacture instruction complete as specified and as directed. Note: Water proofing compound shall be measured and paid separately as supply only.

Preparation of new plastered surface of wall and applying two coat of oil emulsion paint white or tinted over one coat of primer over and including 1mm thick wall care putty on plaster surface, complete all as specified and directed.

Complete removal of existing treatment and preparation of surface of wall and applying two coat of oil emulsion paint white or tinted over one coat of primer over and including 1mm thick wall care putty on plaster surface, complete all as specified and directed.

Preparation of new plastered surface of wall and applying by finishing walls with acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed.

Complete removal of existing treatment of wall and applying by finishing walls with acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed.

Preparing of new plaster surface of ceiling and applying three coats of white wash complete all as specified and as directed.

Preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. including cornices, pilasters etc.; plastered or unplastered surfaces and applying two coat of white wash complete all as specified and as directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out from trenches, floors or wall, complete all as specified and as directed.

Dismantling of 75mm dia cast iron or reinforced concrete drain pipes, jointed in cement motar and taking out of trenches, floor or wall complete all as specified and as directed.

100mm dia cast iron pipe (sand cast) spun pipes soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and as directed.

100mm dia cast iron pipe (sand cast), soil, waste and vent pipes in any length with or without ears, with cement joints, as in floors or laid in trenches or floor, complete all as specified and as directed.

75mm dia cast iron pipe (sand cast), soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and as directed.

75mm dia cast iron pipe (sand cast), soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls, complete all as specified and as directed,

CI bend (any radius) with ducks foot or heel rest of 100mm bore complete all as specified and as directed.

CI branch pieces single equal or unequal, ordinary or inverted with parallel branch of bore 100mm complete all as specified and as directed.

CI branch pieces single equal or unequal, ordinary or inverted with parallel branch of bore 75mm complete all as specified and as directed.

CI Bends of 100mm diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

CI Bends of 75mm diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

CI branch pieces double equal or unequal, ordinary or inverted with parallel branch of bore 100mm complete all as specified and as directed.

100mm dia CI, P or S trap complete all as specified and as directed.

75mm CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and as directed.

150mm x 100 mm dia, salt glazed stone work gully trap setting and jointing with cement mortar (1:1) complete all as specified and directed.

Precast cement concrete1:2:4 type B-1 using 20mm graded crushed stone aggregate, as in cover slab for manholes and similar work set in cement mortar 1:4 including use of form work, complete all as specified and as directed.

PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints, fixed to walls in repair, complete all as specified and as directed.

PVC (SWR) bends 110 mm dia, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding1.5m in depth for foundation etc.; not exceeding 10 sqm om plan and getting out in any type of soil, complete all as specified and as directed.

Returning filling in, any type of soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, complete all as specified and as directed.

Removing excavated material (soil) exc 250m and not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC/PVC pipe not exceeding 150mm dia including all fittings, complete all as specified and as directed.

PCC (1:3:6) type C-2(using 40 mm graded crushed stone aggregate) as in bed to 150 mm dia internal pipe including packing under & hunching against the sides of pipes after they are laid tested, complete all as specified and as directed.

Salt glazed stone ware drain pipes 150 mm internal dia grade 'A' laid in trenches, jointed & tested, complete all as specified and as directed.

Kitchen Cabinet size (Length and height) as per kitchen space and width should not less then 550mm including partitions, shelves and drawers with brass sliding rails door handles door catchers, over all cabinet internally and externally made with both side PVC laminated termite proof board, 18/19 mm thick ,ISI marked , having following specification :- (i) Outer frame made size 50x47mm with sam board. (ii) Shutter both side PVC laminated termite proof board 18/19mm thick having continuous piano brass hinges of 30mm flap width with one No brass handle of 75mm including brass door catcher of not less than 50 mm size in each shutter. (iii) Drawers made of both side PVC laminated termite proof board, 18/19mm thick including brass handle of front and two sliding rails at sides in each drawers. (iv) All cabinet ,drawers, frames and boards shall be fixed at site with brass screws and PVC plugs of suitable size. Note :- (a) Only front dimensions (length and height) at site shall be measured entered in MB irrespective of Nos of partitios or drawers. (b) Different No of partitions and drawers may be as per site requirement with out any extra cost. (c) Kitchen Cabinet shall be fixed at below the kitchen platform.

Kitchen Cabinet size (Length and height) as per kitchen space and width should not less then 400mm including partitions, shelves and drawers with brass sliding rails door handles door catchers , over all cabinet internally and externally made with both side PVC laminated termite proof board, 18/19 mm thick ,ISI marked , having following specification :- (i) Outer frame made size 50x47mm with sam board. (ii) Shutter both side PVC laminated termite proof board 18/19mm thick having continuous piano brass hinges of 30mm flap width with one No brass handle of 75mm including brass door catcher of not less than 50 mm size in each shutter. (iii) Fixed type shelves made of both side PVC laminated termite proof board, 18/19mm thick. (iv) All cabinet ,shelves, frames and boards shall be fixed at site with brass screws and PVC plugs of suitable size. Note :- (a) Only front dimensions (length and height) at site shall be measured entered in MB irrespective of Nos of partitios or drawers. (b) Different No of partitions and Fixed type shelves may be as per site requirement with out any extra cost. (c)Kitchen Cabinet shall be fixed at above the kitchen platform

Anodised aluminium powder coating grill anodised transparent or dyed to required shade according to IS: 1868 with minimum anodice coating of grade AC15 of approved design /pattern, with approved standard section and fixed to the existing window with C.P. brass/stainless steel screws @ 200mm centre to centre ,including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening , all complete as per requirement and direction, complete all as specified and as directed.

40mm thick plain cement concrete type B-0 1:2:4 using 12.50mm graded crushed stone aggregate as in floor (sunken portion) complete mixed with water proofing compound all as per manufacture instruction laid finished even and rough to receive plaster without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately as supply only.

Frosted glass, 4mm thick, on one side type in squares not exceeding 0.5 sqm each pane, complete all as specified and as directed.

75mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base flooring, complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement and pigment etc., complete all as specified and as directed.

25mm thick sand cushioning, filling under floors including watering and consolidation all as specified and as directed.

15mm thick screed bed or bedding layer for laying floor finished in cement mortar 1:6 complete all as specified and directed.

Chequered cement concrete tiles glossy finish coloured 300mm x300mm x25mm thick pattern as approved by GE as in floor set & jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over with grey pigment cement and pigment, complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Demolition of reinforcement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed.

RCC 1:2:4, type B1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses etc.; complete all as specified and as directed.

RCC 1:2:4, type B1 using 20mm graded crushed stone aggregate as in chajja etc.; complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam hauntings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc.; to rough finished surface of concrete flat complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide, complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-In-Charge.

All as per Srl item No 141 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Mild steel, plain, black sheet 0.80mm thick for mumty door shutter, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints seams, including bending or turning up, mitred angles etc.; as required, complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power, security light) complete, including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes, small patches etc., complete all as specified and directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan including testing on completion complete all as specified and directed.

Taking down ceiling fan, dismantling blades and removing fan and blades and deposite to MES store complete all as specified.

Modular type switch 10 Amps, single pole, 1 way, 1/2 module, 240V, ISI Marked complete all as specified and directed.

Modular type switch 10 Amps, 2 way, single pole,1/2 module, 240V, ISI Marked complete all as specified and directed.

Modular Bell push 6 Amp 1 module complete all as specified and directed.

Modular type socket, shuttered type, 6 Amps, 2/3 Pin combined 2 module, 240V, AC (ISI Marked) complete all as specified and directed.

Modular type socket 6 A/16 Amps, 6 Pin combined shuttered socket 2/3 module with light indication, 240V, AC (ISI Marked) complete all as specified and directed.

Modular type switch 16 Amps, single pole, 1 way, 1/2 module, 240V, (ISI Marked) complete all as specified and directed.

Modular White cover plate with frame, 2 module including metal flush box 2 module Complete all as specified and directed.

Modular White cover plate with frame, 3 module including metal flush box 3 module complete all as specified and directed.

Modular White cover plate with frame, 4 module including metal flush box 4 module complete all as specified and directed.

Modular White cover plate with frame, 6 module including metal flush box 6 module complete all as specified and directed.

Modular White cover plate with frame, 8 module including metal flush box 8 module complete all as specified and directed.

Modular blank plate single module all as specified and directed.

Fan regulator modular type electronic, stepped type(01 to 4/5), 100 to 120 Watts, 240Volts, AC, (ISI marked) complete all as specified and directed.

Bell, AC, 230 volts, single pole multi music type complete all as specified and directed.

Ceiling rose, 3 terminal, PVC/polycarbonate body (ISI marked), complete all as specified and directed

Angle lamp holder, polycarbonate insulated body with back plate for bulb complete all as specified and directed.

LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan and connecting cable three core 0.75 sqmm round PVC sheathed from ceiling rose to fan connector and testing complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete one single pole MCB 20/30 Amps, 240V complete concealed on wall and connecting with all connections complete all as directed.

Sheet metal enclosure DB TPN 4 way double door made powder coated out of CRCA mild steel sheet 1.6mm thick 415 volts 200 amps rated bus bar dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to disturbed surface complete all as specified and directed.

Sheet metal enclosures DB's double door factory made power coated made out of CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wass and making good to disturbed surface and colour matching, fixed in repair, complete all as specified

Sheet metal enclosures DB's double door factory made power coated made out of CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 12 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in wass and making good to disturbed surface and colour matching, fixed in repair, complete all as specified

MCB TPN 63 Amps 10 KA,"C" series, AC, 415Volts, 50Hz, (ISI marked) complete all as specified and directed.

MCB SPN 6 to 32 Amps 10 KA,"C" series, AC, 240Volts, 50Hz, (ISI marked) complete all as specified and directed.

MCB SP 6 to 32 Amps 10 KA,"C" series, AC, 240 Volts, 50Hz, (ISI marked) complete all as specified and directed.

Taking down unserviceable sub main wiring concealed type of any description along with PVC conduit including conduit accessories and made good the disturbed surfaces where ever necessary complete all as specified.

Taking down unserviceable sheet metal enclosure concealed type with MCBs including making good the disturbed surface complete all as specified.

Taking down Exhaust fan, dismantling blades, deposite to MES store yard complete all as specified and directed.

Disconnecting, carefully old Electric water heater of capacity 25/50 Ltrs including PVC Connection and handing over to AGE E/M store yard, refixing the same on the same position after completion of the wall repair works including connection, cleaning of out side surface of the Geyser, testing after completion complete. including making good the surface complete all as directed.

Taking down of old unserviceable GI bracket set fixed on wall including making good the surface complete all as specified and directed.

Point wiring with PVC insulated unsheathed 1100 grade FRLSH cable with multi stranded copper conductor of size 1.5 Sqmm (nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia concealed in wall and surface on ceiling with all conduit fittings & fixing accessories including sunken anodized pressed. Steel terminal box of thickness 1.2mm up to size of 200mm x 300mm and 1.6mm thick for above size of 200mm x 300mm suitable for fixing of module top cover plate as per numbers of switch modules for modular switches, sockets, fan regulators, red colour indicator, blank plates etc.; as approved colours and including 1.5 Sqmm PVC insulated multi stranded FRLSH type unsheathed (green colour), single core cable with copper conductor cable as earth continuity conductor and connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface, complete all as specified and as directed following:

One light point/fan point/ exhaust fan point/ bell point controlled by one switch.

One 3 pin 5 amps socket point controlled by one 6 amps switch on independent board .

One 3 pin 5 amps socket point controlled by one 6 amps switch on same board .

One light point controlled by two 2 way switches.

All as per Srl item No. 178 hereinbefore, but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switch on independent board complete all as specified and directed.

LED bulb 9 watts, 240 Volts, 50Hz pin type and including removing old unserviceable fittings, complete all as specified and directed.

LED lights fitting 1x 20W, 4' long 220V, AC Decorative ultra slim square profile LED lighting fixture with extruded aluminium, environmental friendly, energy efficient with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

LED lights fitting 1x 10W, 2' long 220V, AC Decorative ultra slim square profile LED lighting fixture with extruded aluminium, environmental friendly, energy efficient with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Decorative wall light fixture Globe type including 9 W LED Lamp made up of aluminium complete all as specified and directed.

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, 230V, 50 Hz, Copper winding of sweep 200mm including making suitable hole on brick wall and making good the hole with cement plaster and provision of cable 3 core of 0 .5 sqmm from ceiling rose to fan complete all as specified and directed.

Sub main wiring complete with 2 run of 6 Sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FRLSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade (MMS) with all connected accessories such as Bend,Tee,Elbow,Short pieces etc. concealed in wall/roofs/floors and including one run of 6 Sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only.

All as per item ser No 185 above but 2 run of 4 Sqmm single core and one run of 4 Sqmm single core as earth wire for geyser.

Earthling complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directly in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade, GI funnel with wire mesh, including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45X 45X 45 CM, RCC cover 1:2:4 type B1 of size 45X45X6CM, excavation/earth work in any type of soil and returning filling, removal of surplus soil and testing/test point for required value including removing old unserviceable earthling items, complete all as specified and directed.

GI bracket pipe of size 40 mm dia, medium grade of 1.0 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick: 02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc., complete all as specified and directed.

Deduction to be made from BOQ for Sch 'A' Part - II (Schedule of credit) Amount of Rs. 10,70,456.00 during AOC. Note: Tenderers shall not quote for this schedule.

M/S KAPIL KUMAR KHATTAR (BID ID -3122658)

Standard engineers (BID ID -3125105)

TRIVENI CONSTRUCTIONS (BID ID -3134111)