Provn of concrete platform/hard standing at NOI Goa galvalume sheet shed from senior secondary wing to Porta cabin adjacent to security post at NCS Goa and addn altn and special repairs to bldg No P 152 near swimming pool at GNA under GE Gomantak

Amount

Surface excavation n. exe (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/disintregrated rock

M&L hardcore of broken stone of boulders gauge n.exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface.

M & L for 75 mm thick PCC type D-2, (1:4:8) (using 40 mm graded aggregate) as in sub base.

M&L for moorum/red bajri filling in floors or paving, laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering.

M & L for 100 mm thick PCC type B-2, (1:2:4) (using 40 mm graded aggregate) as in Hardstanding.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m soft/disintegrated rock.

M&L for screed bed or bedding layer of 15 mm thick for laying of floor tiles in CM (1:4).

M & L for rendering 10 mm thick CM 1:4 on on fair faces of brickwork or concrete surfaces for receiving wall tiles.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 Sqm but nexc 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for glazed ceramic coloured tiles in vertical surfaces/ Skirting 250 x 375 x7 mm thick set and jointed neat cement slurry and pointed in white /coloured cement to match.

M&L for pre-cast cement concrete block masonry, type C1 1:3:6 (20 mm graded aggregate) with solid blocks exc. 10 cm in width and setting in cement mortar 1:6

M&L for rendering 10 mm thick in CM 1:6 on concrete surface even and smooth without using extra cement.

M&L for applying two coats of Cement base paint over a coat of primer including preparation of new plastered surfaces of wall complete.

Excavating in post holes (or similar holes) in soft/disintegrated rock each n.exc 0.5 cum, getting out , returning, filling and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete.

Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe-410-W(Gde-E-250) quality-B)

M&L for two coat of synthetic enamel paint on steel surfaces including preparation newly steel surfaces over a coat of red oxide primer, over 10 cm in width or girth, not other wise described.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified Sheet shall be laid in curve shape to match existing shed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge fixed with self tapping screws as specified Sheet shall be laid in curve shape to match existing shed.

M&L for forming construction (Dummy) joints 65mm deep x 10 mm wide, filled with cealing compound Grade 'A'.

S&F aluminium powder coated frame and shutters for windows/ventilators sliding/fixed/openable type complete with necessary fittings such as two concealed lock for each window, roller etc and fixing all as speciefied and directed by Engineer-in-Charge. Note : Weight of aluminium three track section and tubes for windows/ventilators shall not be less than 0.55 Kg/RM and not more than 1.00 Kg/RM. Note : (a) The weight of rubber gasket beading will not be measured with the weight of aluminium shutters, glass will be measuerd and paid separatelly. (b) The rate quoted by the contractor shall also include necessary wheels for sliding shutters and hinges for side hung/top hung shutter as required at sight and concealed locks for windows. (c) The colour of powder coating shall be as approved by GE

S&F glazing with 5.5 mm thick in square or rectangular shape exc 0.50 sqm fixed with rubber gascut and aluminium beading etc.

S & F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exc 1.50sqm.

S&F glazing with 4mm thick plain sheet glass in square or rectangular shape exc 0.50 sqm fixed with rubber gascut and aluminium beading etc.

M&L for 12 mm thick prelaminated particle board, interior grade, prelaminated on both side with decorative choice lamination fixed with screw to timber framework.

S&F Rolled and hollow sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe-410-W(Gde-E-250) quality-B)

S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall

S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to froor

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor.

S & F 110mm bore PVC (SWR) bends With acces door any radius

S & F 75mm bore PVC (SWR) bends with access door any radius

S&F Solid PVC wall lining consisting of 5mm thick wood grain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall penelling inclusive of fixing on to wall to make PVC frame as per specification.

Demolition of precast concrete block walling/ boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete walling etc.

Taking down excisting collapsible gates and refixing the same to another opening after servicing and over hauling complete.

Taking down chowkhats or frame n.exc 1.5 sq. m each( without taking off shutters from frame)

Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq m each( without taking off shutters from frame)

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Hacking out old broken glass (any thickness size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads.

M&L forming jambs etc to opening including cutting toothing and properly bonding into old work including facing and plastring to match existing work in cement mortar 1:6 etc. complete.

S&F flat iron of size 25mm x 3 mm as in hold fasts confirming to Fe-290 Grade 'E' 165.

M&L for cement concrete type C2 1:3:6 (40 mm graded aggregate) as in inserting of holdfasts.

S&F Aluminium anodised handle of size 150 mm, "D type" complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt 100 mm long of extruded section all as specified.

S&F Butt hinges cold rolled mild steel medium weight 100 mm.

S&F Brass 2 lever mortice lock ,vertical type of size 100 mm all as specified and as directed.

M&L for Brass floor springs 300 mm (ISI Marked) for aluminium doors all as specified.

Taking down GI tubing15 mm dia and connections and refixing old steel tubing and connections in new or old positions.

Supplying and laying of CPVC pipes of 20 mm outer dia.SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Suppling and fixing in repair 15 Stop valves,fency type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F 15mm, fancy type CP, Pillar taps, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F PVC connections 15mm size with PTMT nuts of length 450mm

Suppling and fixing in repair 15 mm dia fency type bib taps,chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repairs vitreous china wash basin, white, flat back, size 550x400mm excluding ditto but including brackets including cutting for and pinning in ends of brackets or erecting stand including Supply and fixing of waste pipe

M&L for screed bed or bedding layer of 20 mm thick for laying of floor tiles in CM (1:4).

M & L for rendering 10 mm thick CM 1:4 on on fair faces of brick work or concrete surfaces for receiving wall tiles.

M & L vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20 mm screed in CM (1 : 6)

M&L for non-skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and joints in near cement slurry and pointed in white or coloured cement to match.

M&L for glazed ceramic tiles 7mm thick, in floors etc set and joints in near cement slurry and pointed in white or coloured cement to match.( size 400mm x 400mm)

Dismentling stone slabs and tiles of any description or thickness in floors, aprons etc laided, bedded and pointed in any mortor.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for rounding to edges of granite stone slabs one edge, such as in steps, cooking platform, and other similar situations (inner side only)

M & L Pre-cast cement concrete Type C 1 ( 1 : 3 : 6 ) 20mm graded aggregate block masonry with solid blocks, exc. 10 cm in width and setting in mortar (1 : 6 ) , complete

Rendering 10mm thick in CM ( 1 : 4 ) on fair faces of brick work or concrete surface finished even and smooth without using extra cement (Internal Surface)

M&L 15 mm thick plastering in CM 1:4, (external wall)on surface other than fair face of brick work finished smooth and even, including mixed with liquid water proofing compound with cement on wall in shafts, etc finished even and smooth without using extra cement all as directed by Engineer-n-Charge. Note : Water proofing compund measured and paid separately

Supplying Liquid water proofing compound

M & L 2 coats of synthetic enamal paint (Luster Paint) over a coat primer on plastered surfaces, preperation to complete removal of existing treatmentg.

M&L for applying two coats of acrylic emulsion exterior paint (anti fugal paint- APEX) cover a coat of acrylic emulsion exterior primer including preparation of new plastered surfaces of walls complete all as specified and directed.

M&L for applying one coats of acrylic emulsion exterior paint (anti fugal paint- APEX) cover a coat of acrylic emulsion exterior primer including preparation of old plastered surfaces of walls complete all as specified and directed.

M&L Hard core of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface

Demolition of reinforced cement concrete any description not otherwise described

M&L PCC 1 : 3 : 6 type C2 40 mm graded aggregate finishing the surface even and fair as in plinth protection - 75 mm thick.

M & L Cement concrete type C-2, 1:3:6 (ditto) 100 mm thick as in sub base

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in hard/dense soil

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in soft disintegrated rock

M/L for sand cushion in trenches for cable protection complete all as directed and specified.

Supply and lay PCC cable cover class LV type 1 flat size 250mmx150mmx40mm. Make : Mehtab/National

M&L for Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in thick using excavated hard/dense soil.

M&L for Removal of surplus soil to a distance not exceeding 50 m and depositing where directed by Engr-in-charge.

M&L GI pipe medium grade 40 mm dia complete with all fitting laid in ground/trench all as directed and specified. Make : Jindal/Tata

M&L for Cement concrete in foundation filling and mass concrete 1 : 4 : 8 type D2 complete all as directed by Engineer-in-charge.

Supply and lay LT cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 25 sqmm 4 core as specified and directed by Engr-in-Charge. Make : Polycab/Havells/Gloster

Supply and installation of LT panel 'KIOSK type' cubical, weather, water, dust and vermin proof (out door type) CRPI approved suitable for operation on 1100 volts 3 phase, 4wire, 50 HZ AC electric supply, externally powder coated & internally painted with two coats of synthetic enamel paint over one coat of red-oxide primer, made out of 3mm thick CRCA steel sheet as suitable size having opening and locking arrangement both from front and rear side with cable tray of size not less than 20cm including copper busbar strip size 50x6 mm, 04 Nos. fixing on angle iron size of 50 x 50 x 6mm including connected accessories and necessary PCC work 1:3 :6 type C-2 blocks complete with following accessories :- (a) Supply and fixing onload changeover switch 63 Amps without enclosure (b) Supply and fixing MCCB 4 pole 415 Volts of breaking capacity of 10 KA of 63 Amps (Incoming) (c) Supply and fixing MCB 4 pole 415 Volts of breaking capacity of 10 KA of 32 Amps (Outgoing) (d) Supply & fixing switch socket combination outlet 2 in 1 5 pin 5 Amps flush type. (e) Supply & fixing switch socket combination 2 in 1, 6 pin 15 Amps flush type. (f) Supply and fixing LED Indicating lamps for Main Supply indicating R, Y, B

Taking down carefully copper/aluminium point wiring any type (light, fan socket or power) complete (fittings such as switches, ceiling roses pendants, regulators, sockets etc to be measured separately) removing materials at site and making good disturbed surfaces of walls floors etc.

M&L for one light point or fan point controlled by one switch with cables 1.5 Sqmm copper cable FRLS multistranded unsheathed drawn through & including casing and caping and 1.5 sqmm conductor cable for earth wire including making connection with common earth and earth dolly including pressed steel terminal al boxes concealed in wall with 3 mm thick plastic laminated sheet top cover fixed with brass screw for mounting switches sockets regulator etc all as per directed by Engr-in-Charge.

M&L for point wiring for 5 amp independant point with 1.5 sqmm copper wire & 1.5 sq mm copper wire as earth lead drawn through & including casing and caping of suitable size.

M&L for point wiring for 15/25 amps independant point with 4 Sqmm copper wire & 4.5 Sqmm copper wire as earth lead drawn through & including casing and caping of suitable size.

Supply & Fixing modular switch 1 way 6A, 1 module, 230 volts.

Supply & Fixing modular switch one way 16 Amps, 1 module, 230 volts.

Supply & Fixing modular switch one way 25 Amps, 1 module, 230 volts.

Supply & Fixing modular socket 6 Amps-2/3 pin combined, 2 module.

Supply & Fixing modular socket 6A/16A-2/3 pin combined, 2 module.

Supply & Fixing modular socket 25A-2/3 pin combined, 2 module.

Supply & fixing modular metal flush box 3 module.

Supply & fixing modular metal flush box 8 module.

Supply & fixing modular white cover plate with frame, 3 module

Supply & fixing modular white cover plate with frame, 8 module

Supply & Fixing ceiling rose, surface Bakelite 65x50 mm Two to three terminals

Supply & Fixing Modular fan regulater electronic step type 120 watt 280 volt including removal of old one complete.

Supply & fixing MCB, 6 to 32 Amps, single pole, C Series, 10 KA, 240 volts.

Supply and fixing MCB 32 Amps TPN, C Series, 10 KA, 415 volts.

Supply & Fixing sheet metal enclosure DB, 4 way, TPN, double door factory made powder coated including neutral and earth link connector flush fixed in wall complete including dismantling of old one.

Supply and Fixing LED tube light fitting surface mounted integrated type with 20 watts LED having minimum 100 lumens/watt complete including dismantling old fittings all as specified and directed.

Supply and Fixing LED light fitting Recess/Surface mounting LED flat panel 2'x2' with high efficient LEDs & glare free opal diffuser of 34 watts LED including dismantling old fittings all as specified and directed.

Supply & Fixing LED Bulk head fittings designer type with having 10 Watts LED complete all as specified and directed.

Supply & fixing ceiling fan 1200mm sweep (ISI marked), 230 volts, (BEE rating 5 star) with connecting rod including removal of old one and depositing at MES Store complete.

Supply & fixing exhaust fan 300mm sweep, heavy duty, 230 volts including removal of old one and depositing at MES Store complete.

Supply & Fixing Submain wiring with three runs (Phase, Neutral & Earth) of 2.5 sqmm single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in casing capping including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

Supply & Fixing Submain wiring with Five runs (03 Phase + 01 Neutral + 01 Earth) of 6 sqmm single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in casing capping including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

M/S jvsr constructions

K M Subhanaiah

M/s Gayatri Contruction Co.

Tara Construction