SITC of Lift

Amount

SITC of automatic lift (as per manufacturer design as per detailed spectfication conforming to IS mentioned in Annexure -I ) and putting into operation after final testing in the existing shaft complete with all accessories and reparing the damaged wall /floor if any etc to complete as required. Make:- OTIS/KONE/Schindler/Thyssen Krupp/ Bharat Elevator Co. Ltd/EVS/Electromec/United Elevator/ Escon/Jhonson/Omega/LT Elevator.(Category-I and II)

Type : Passenger Lift without Machine Room

Load : 16 Passengers / 1088 Kg.

Control: Microprocessor based with Serial Communication. Controller in shaft and user interface in landing

Drive: VVVF Drive with feedback control (closed loop)

Machine: Energy Efficient Machine ; Gearless without Machine Room.

Speed : 1.0 Mtr. /Sec.

Floor Served : G + 3 (4 Stops)

Landing : 4 lands ; All on same sides

Total Rise : 13.5 Mtr. (approx)

Operation : Microprocessor based simplex full collective with or without attenedent.

Signals : Digital Car postion indicator, car travels direction indicator in car and at all landing with call registration indicator. COP & LOP must have stainless steel face plate silver brushed with surface mounted button with braille. Button : All buttons on car & landing shall be luminous & encoded with braille on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendent mode of operation. Display type : Monochrome/ Colour LCD / Segmented LCD/ Scroll. Operation Push Buttom for lift maintenance & service should be on top of the car.

Travelling Accuracy: ± 5mm (Micro Levelling Arrangement)

Car Inside:1600 mm (W) x 1600 mm (D) x Min. 2200 mm (H)

Car Entrance : Clear Opening 1000 mm (W) x 2000 mm (H) protected with car door.

Car Door : Stainless Steel Centre Opening (COPD) / Telescopic Opening (TSPD) automatic door provided with V3F controlled door drive system with 2D Infrared Curtain of light & Mechanical Force Limiting Device.

Landing Door: Stainless Steel Centre Opening (COPD) / Telescopic Opening (TSPD) automatic door provided with V3F controlled door drive system with fire rating of 120 min.

Door Opening: Automatic Power operated door with full length photocell assembly curtain sensor.

PROTECTIVE DEVICES & OTHER ACCESSORIES :-

ARD: Automatic rescue device complete with dry maintenance free batteries as required for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection. On overloading condition the lift car will not start with door remaining open and give audio & display indication.

Emergency Lighting In Car: Battery operated emergency lighting in the lift car.

Intercom System: Battery operated Intercom System in Lift Car, Machine Room & Control Room.

Emergency Alarm: Battery Operated alarm bell system in Lift Car & Control Room.

Fireman switch : Fireman switch placed at ground floor.

Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the lift.

Car Parking at top floor at idle condition.

Main Wire Rope/ Belt : As per manufacturer's standard conforming to IS.

Auto fan Cut-Off

DIMENSION OF SHAFT & POWER SUPPLY :-

Available Shaft Dimension: 2575 mm (W) X 1925 mm (D)

Pit Depth: 1600mm ( Bidder should visit the site)

Overhead: 5500mm ( Bidder should visit the site)

Electric power supply: AC 415V, 3 Phase, 50Hz terminated in machine room as per IS.

Note: 1) All the above rates should be quoted inclusive of all taxes & duties, District charges and LWC as applicable, with cost of maintenance, servicing, supply & replacement of spares for 03 (Three) years from the date of commissioning. 2) The Agency must procure the materials from the manufacture/OEM or their authorised sales Channel so that the standard warranty/support of the manufacturerer/OEM becomes applicable to the product to be delivered and installed by them. Documents that authenticate such procurement from the manufacturer/OEM or from their authorised sales Channel and standard warranty/support should be sent from the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work/submission of bill. If any refubrished materials are supplied and installed, penal action will be taken as per existing rule. Before execution of the work the prospective bider has to submit layout drawing as per design of OEM dully approved by the OEM. 3) Total is rounded off to the nearest rupees.

ELECTROMEC (BID ID -7557452)

Escon Elevators Pvt. Ltd. (BID ID -7504890)