REPAIRS TO HARD STANDING, BRICK WORK, RETAINING WALL, BOUNDARY WALL, COMPOUND WALL, CHAIN LINK FENCING, BOUNDARY PILLARS AND PPGL SHEETS AT ARTY CENTRE UNDER GE NASIK ROAD.

Amount

Dismantling asbestos cement (corrugated,semi corrugated)sheets in roof covering.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, drip and straight flashing.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F rolled mild steel joist, channel, angle, flat section fixed independently without connecting plates or MS tubular sections etc (cut to ordinary length i.e. within 20mm length indicated) grade Fe 410-W (E 250) all as directed by Engr in Charge.

S&F Steel work in tubular trusses including special shaped washer etc. tubular purlins post, rafter including necessary cutting welding etc complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as specified and directed.

S&F Framed work rolled mild steel plain angle cleats and plate for securing purlins to ragfter and similar small articals confirming to Fe-410-0 or Fe -250- as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section embeded in concrete, including taking out embedded portion and making good disturbed ground.

Excavating in post holes (or similar holes) each n exc 0.5 cum in hard /dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface.

M&L for PCC 1:3:6 type C2 (using 40mm graded aggregate ) in foundation for post holes.

S&F in repairs Galvanised. 2 strand, steel barbed wire 2.20 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing as directed by EIC (each line wire to be measured).

S&F Framed work such as MS grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

Dismantling fencing wire mesh, any type.

Supply only chain link fencing MS galvanised incl line wire any mesh size & standard rails , straightning bolts etc including providing of binding wire exc 4 kg/sqm

Fixing only chain link fencing including MS galvanised with line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire. Note:-Line wire shall be measured separately.

M&L for 6 to 8 mm dia TMT bars cut to length and binding with mild steel wire (Annealed) not less than 0.9 mm dia complete all as specified.

M&L for two coat synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description over 10cm in width or girth not otherwise described including preparation of new surfaces.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n exc 15cm long dia of neck in mm 16 mm to 20 mm complete alll as specified and directed.

S&F steel work in such post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in , etc., and similar work conforming to Fe-290 Gde E-165 rails braces holdfast etc

Demolition of brick work built in cement mortar (including coping).

M&L for brick work with fly ash brick straight or curved on plan exc. 6 mtr mean radius, built in CM 1:6 with old size bricks.

M&L for rendering 15 mm thick in on fair faces of brick work or concrete surfaces in cement mortar(1:4) finishing even and smooth without using extra cement complete all as specifed and directed

M&L for preparation of newly plastered surfaces and applying two coats of white wash complete all as specified and directed by EIC.

Demolition of Cement Concrete of any description in ground floor & paving n.exc. 15 cm thick(below or above ground level).

M&L for 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) in sub base of flooring/hard standing.

M&L for providing 25 mm Thick PCC 1 : 2 : 4 type B0 as in sub base of flooring/hard standing all as specified.

Forming Construction joints 66mm deep x 10mm wide, filled with sealing compound grade `A' thickness of slab 100mm all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping.

M&L for Providing precast cement concrete louvres and jallies Type B-0 (1:2:4) in CM 1:4, 25mm thick (mea-sured solid), including all mouldings but excluding frame.

M&L for filling of gap portion of gable wall with PCC (1:3:6) type C1 of any height with suitable arragement of shuttering & formwork all as specified and directed by EIC.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 1,69,750.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

PARADISE MILESTONE (BID ID -3074419)

sunway associates (BID ID -3074117)

Vinod Enterprises (BID ID -3085744)

Abhiraj Enterprises (BID ID -3084078)

M/S R.K.S. CONSTRUCTION (BID ID -3087524)

M/S K. K. Construction (BID ID -3074298)

Bidder Name

MAHIMA CONSTRUCTION

M/S K. K. Construction

sunway associates

Vinod Enterprises

M/S R.K.S. CONSTRUCTION

Abhiraj Enterprises

PARADISE MILESTONE