Estimate for Construction of Escape Regulator Off Take at Rd 19765 of Ramsara Minor Out Falling In Abul khurana Drain Rd 105855 including Fabrication of Gate and Gearing System.

Earth work in Excavation in of foundation of structure as per drawing and technical specification , including setting out, construction of shoring and bracing , removal of stumps and other deleterious matter( CSR 21.1 B) DEPTH UP TO 3 MTR

Earth work in Excavation in of foundation of structure as per drawing and technical specification , including setting out, construction of shoring and bracing , removal of stumps and other deleterious matter( CSR 21.1 B) DEPTH ABOVE 3 MTR AND UPTO 6 Mtr

PCC M-10 Cement Concrete in Sub Structure Complete as per drawing and technical specification using mixture. (CSR Item No. 10.12 ) (a(i)) mixing manual means

CCM-15 plain/ Reinforced Cement Concrete in open Foundation complete as per drawing and specifications. PCC Grade M15 (C.s.r -21.7 a)

R.C.C.M-25 height upto 5 mtr with batching plant transist mixure and concrete pump (CSR Item no: 21.32 f/a/ii).

Providing, Running and maintenance of pumping set 8 H.P./ Generator set for dewatering arrangements complete in all respects. (As per open Dewatering Plan attached) (CSR Item No. 25.4)

Suppling fitting & placing uncoated HYSD bar Reinforcement in Foundation complete in drawing and technical specification csr 18.18

Removing Hume Pipe dia 1000 mm

Providing & fixing in position of flat/wedge seal including preparation of surface complete in all respects and to entire satisfaction of Engineer in charge.(75 mm dia x 10 mm th.)

Providing of hollow bulb seal & fixing in position including preparation of surface complete in all respects and to entire satisfaction of Engineer in charge. (100/44)

Supply, Providing and fixing of Stainless steel Bolts & nuts (for seals of all types) with washer of all sizes and length required as per sample / drawing / direction of Engineer-In charge complete in all respects.

18 (CSR 18.15) Nuts & Bolts of all sizes and length required

Providing & fixing clamp plate, complete in all respects.

Painting of gate leaf with primer coat and two coats with Anti corrosive Bitumastic paint to give an even shade with special quality paint.

Providing and fixing Skin Plate 8 mm

Providing and fixing ISMC

Providing and fixing ISA 65X65X6mm @ 5.8 Kg/m

Supply of multi purpose Synthetic hetiv grease

Supply of Diesel

Supply of Mobil Oil ((1 Litre Packing) M-30(XVI))

Providing and fixing of chequred plate

Providing and fixing M.s Plate i.e Stiffner Plate, , Top Base Plate, bottom base plate, ladder base plate, Square bar, flat plate Etc

Providing and fixing 40 Nb

Pipe Fixing and Holding the gate with the help of 35 tonne capacity crane.

Providing and fixing Sqaure hollow section

Providing and fixing Stainless steel flat, complete in all respescts.

Providing and fixing ISST 100 @8.1 KG/M

Providing and fixing ISMB

Commisioning & testing of Gates at site complete in all respects and to entire satisfaction of Engineer In charge.

Drilling/Boring hole including rimming complete in all respects and to entire satisfaction of engineer in charge (i) 0-10 dia

CHAPTER NO. 29 SEWERAGE AND DRAINAGE (42) Providing, lowering in trenches to correct gradient and allignments, jointing with tytone rubber joint and cutting of RCC S/S pipes having inside HDPE. lining ISI marekd as per ISI code IS:458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc.,cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed. The pipes shall rest on the beds at all joints through their lengths and to ensure this, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer incharge including all cartage etc copmplete in all respects. (A) R.C.C. pipe with inside H.D.P.E. lining class- NP-3 (f) 800mm i/d pipe with inside H.D.P.E. lining

CHAPTER NO. 16 WHITE WASHING, DISTEMPERING, PAINTING & POLISHING(16.18) Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint.

CHAPTER NO. 16 WHITE WASHING, DISTEMPERING, PAINTING & POLISHING(16.18) Supply providing and fixing of spindle hoist 1.0 Ton capacity including CI Housing Cover with worm and worm wheel assembly, shaft, handle, gun metal bush with triple start threading inside for Spindle complete including labour charges. (1.0 Ton capacity), Supply and fixing of Spindle Cover and M.S Spindle with double start or triple start threading 11‘Height 1/3/4" dia complete in all respects

Any other item

MAGIC BUILDERS

The Behelewala Cooperative Labour and Construction Society Limited

AMIT MODI CONTRACTOR

VARSHA CONSTRUCTION CO

VARINDER KUMAR CONTRACTOR