UPGRADATION OF EXISTING STP AT LOHARA MARG FOR SECONDARY TREATMENT FOR TERTIARY TREATMENT UNDER GE W MATHURA

Amount

Excavation over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation over areas exc 1.5m but not exc 3m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-charge.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.50 mtr depth for foundation etc or for shafts, wells, cesspits, main holes, pier holes, laying of cable etc complete in hard/dense soil complete all as specified and directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soil complete all as specified and directed.

Removing excavated soil not exc 50 mtr and deposited where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed.

Removing excavated soil exc 250 metre but not exc 500 metre and depositing where directed at a level n.exc 1.5 Mtr above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) type D-2, using 40mm graded stone aggregate in foundation, filing and mass concrete complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces of concrete flat complete all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter complete all as specified and directed.

M/L TMT steel bars 6 to 8 mm dia TMT bars over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including mild steel wire (annealed ) not less than 0.90 complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) ladder/railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the ladder/railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

M&L for reinforced cement concrete M-30 design mix using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under- reamed piles and mass concrete complete all as specified and directed by Engineer-in -charge.

M&L for reinforced cement concrete M-30 design mix using 20 mm graded crushed stone aggregate as in Walls, retaining walls, basement walls, ballast walls and the like, any thickness;, above top of footings including attached pilasters and buttresses complete all as specified and directed by Engineer-in -charge.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge. Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed.

M&L hard core of guage not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M&L 5mm thick cement plaster on concrete surface in CM 1:3 on concrete surface finished even & smooth without using extra cement mixed with integral water proofing compound (WPC shall be measured seperately) all as specified and directed.

Supply only inegral waterproofing compound all as specified.

S&F PVC water bar complete all as specified and directed.

M&L 5mm thick cement plaster on concrete surface in CM 1:3 on concrete surface finished even & smooth without using extra cement complete all as specified and directed

M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint over a coat of white wash complete all as specified and as directed.

Supply, installation, testing and commissioning of high speed Monoblock pump set Capable to deliver 8 LPS at 17mtr head made of CI Casing, CI impeller, CS shaft, Stuffing box Gland packed and capable to handle 40mm suspended soft solids, coupled with 3 Phase IE2, 415V, IP55, 50Hz electric motor, driven Running RPM 2900 (± 10%) as per manufacturer recommendations complete with all accessories and comprising of the following:- (i) Suitable size wiring between motor to starer using single core copper conductor flexible cables drawn through and including of 2 runs of 32mm dia including earth conducting conductor all and rated, PVC pipe, cable lags gland etc. Cont/-

Cont/- (ii) Bourden'srdens type pressure gauge 100mm dial type on delivery of pump set. (iii) Common base foundation for pump set made of ISMC 100 suitable for above pump set as for manufacturers recommendation. (iv) PCC foundation alongwith shed water proof shed grouted in CM 1:2:4 type B-2 using 20mm graded aggregate 20cm above GL and 30cm below GL including grounding of eye bolts nuts etc pump set of inadequate size as per manufactureses recommendations.

Supply, installation, testing and commissioning of high speed Monoblock pump set Capable to deliver 13.5 LPS at 14mtr head made of CI Casing, Bronze impeller, 40C8S shaft, Stuffing box Gland packed and capable to handle 60mm suspended soft solids, coupled with 3 Phase IE2, 415V, IP55, 50Hz electric motor, driven Running RPM 2900 (± 10%) as per manufacturer recommendations complete with all accessories and comprising of the following:- (i) Suitable size wiring between motor to starer using single core copper conductor flexible cables drawn through and including of 2 runs of 32mm dia including earth conducting conductor all and rated, PVC pipe, cable lags gland etc Cont/-

Cont/- (ii) Bourden'srdens type pressure gauge 100mm dial type on delivery of pump set. (iii) Common base foundation for pump set made of ISMC 100 suitable for above pump set as for manufacturers recommendation. (iv) PCC foundation alongwith shed water proof shed grouted in CM 1:2:4 type B-2 using 20mm graded aggregate 20cm above GL and 30cm below GL including grounding of eye bolts nuts etc pump set of inadequate size as per manufactureses recommendations.

Supply, installation, testing and commissioning of high speed Monoblock pump set Capable to deliver 7 LPS at 25 mtr head made of CI Casing, SS 304 Impellar , SS 316 Shaft, Stuffing box Gland packed and capable to handle 60 mm suspended soft solids Coupled with 3 Phase IE2 ,415V, IP55,50Hz electric motor driven Running RPM 2900 (± 10%) as per manufacturer recommendations complete with all accessories and comprising of the following:- (i) Suitable size wiring between motor to starer using single core copper conductor flexible cables drawn through and inclluding of 2 runs of 32 mm dia including earth conducting conductor all and rated, PVC pipe, cable lags gland etc. Cont/-

Cont/- (ii) Bourden'srdens type pressure gauge 100 mm dial type on delivery of pump set. (iii) Common base foundation for pump set made of ISMC 100 suitable for above pump set as for manufacturers recommendation. (iv) PCC foundation Alongwith shed water proof shed grouted in CM 1:2:4 type B-2 using 20 mm graded aggregate 20 cm above GL and 30 cm below GL including grounding of eye bolts nuts etc for pump set of inadequate size as per manufactureres reccommendations.

Supply, installation, testing and commissioning of high speed Monoblock pump set Capable to deliver 15 LPS at 23 mtr head made of CI Casing, CI Impellar , CS Shaft, Stuffing box Gland packed and capable to handle 60 mm suspended soft solids Coupled with 3 Phase IE2, 415V, IP55, 50Hz electric motor driven Running RPM 2900 (± 10%) as per manufacturer recommendations complete with all accessories and comprising of the following:- (i)Suitable size wiring between motor to starer using single core copper conductor flexible cables drawn through and inclluding of 2 runs of 32 mm dia including earth conducting conductor all and rated, PVC pipe, cable lags gland etc. Cont/-

Cont/- (ii) Bourden'srdens type pressure gauge 100 mm dial type on delivery of pump set. (iii) Common base foundation for pump set made of ISMC 100 suitable for above pump set as for manufacturers recommendation. (iv) PCC foundation Alongwith shed water proof shed grouted in CM 1:2:4 type B-2 using 20 mm graded aggregate 20 cm above GL and 30 cm below GL including grounding of eye bolts nuts etc for pump set of inadequate size as per manufactureres reccommendations.

Suplying, laying, jointing & testing of Heavy class GI pipe both end flanged alongwith rubber sheet and nut bolts including fitting like tee,socket, bend etc, nominal dia 100 mm bore as per IS 1239 (2004) thickness 5.40 mm including fitting and testing specifications in any length, laid in trenches, cutting of hole in building complete with and including necessary joints complete all as specified and directed. Note : Excavation & earth work shall be measured and paid for seperately under appropriate item of this schedule.

Suplying, laying, jointing & testing of Heavy class GI pipe both end flanged alongwith rubber sheet and nut bolts including fitting like tee,socket, bend etc, nominal dia 80 mm bore as per IS 1239 (2004) thickness 4.8 mm including fitting and testing specifications in any length, laid in trenches, cutting of hole in building complete with and including necessary joints complete all as specified and directed. Note : Excavation & earth work shall be measured and paid for seperately under appropriate item of this schedule.

Suplying, laying, jointing & testing of Heavy class GI pipe both end flanged alongwith rubber sheet and nut bolts including fitting like tee, socket, bend etc, nominal dia 150 mm bore as per IS 1239 (2004) thickness 5.40 mm including fitting and testing specifications in any length, laid in trenches, cutting of hole in building complete with and including necessary joints complete all as specified and directed. Note : Excavation & earth work shall be measured and paid for seperately under appropriate item of this schedule.

Supply fixing and testing non return valve of size 100 mm bore ISI Marked alongwith nut bolt complete all as specified and directed.

Supply fixing and testing non return valve of size 80 mm bore ISI Marked alongwith nut bolt complete all as specified and directed.

Supply installation and fixing of Butterfly valve made of cast iron ISI Marked with handle for opening and closing suitable for pipe of dia 80 mm complete all as specified and directed.

Supply installation and fixing of Butterfly valve made of cast iron ISI Marked with handle for opening and closing suitable for pipe of dia 100 mm complete all as specified and directed.

Supply installation and fixing of Butterfly valve made of cast iron ISI Marked with handle for opening and closing suitable for pipe of dia 50 mm all as specified and directed.

Supply, installation, testing and commissioning of LT panel, outdoor type, floor mounted not less than of 1500 mm x 1650 mm x 450 mm IP -54 degree of protection suitable for 3 phase, 4 Wire system , 415 Volts, 50 Hz ,CPRI approved factory made having independent compartment for 100 Amps bus bar incoming feeder and each out going feeders of 32 Amp, dust and vermin proof, outer shell fabricated of 2 mm thick CRCA sheet & made out angle iron frame of 40 mm x 40 mm x 5 mm (for external) with seven tank treatment process for powder coating with thickness not less than 60 micron Cont/-

Cont/- provided with suitable gasket to make it dust/vermin proof & general construction confirming to IS 8063/93, pedestal flame grouted in PCC (1:2:4) type B-1 20 mm graded stone aggregate, thimble and cable entry boxes with cable glands including disconnecting and dismantling old LT panel of any size complete in all respect and comprising of the following: Inner Shell:- Inner shell made out of 1.6 mm thick CRCA sheet duly compartmentalised for each control gear, front lockable/openable by keys from both sides having chromium plated 19 mm dia fancy lock (02 Nos in each Cont/-

Cont/- neutral flow of air 'U' type completely vermin proof & to accomodate incoming/outgoing MCCBs and TPN aluminium bus bar of rating not less than 1.5 times of rated capacity of incoming MCCB. The colour coded heat shrinkable sleave for bus bar and shall be mounted on non hydroscopic, non combustible,track resistant, high strength FRP/SMC/DMC material at an interval not more than 250 mm throughout complete all as specified and as directed- Cont/-

Cont/- Incoming:- (a) MCCB - 63 Amp, 415 Volt, 4 pole, 36 KA with adjustable thermal & magnetic protection/setting, Ics = 100 % Icu, thermal adjustable - 0.8 to 1 In, magnetic adjustment - 5 to 10 In in accordance with IS/IEC 60068-2-6 standard. - 01 Each Outgoing:- (b) MCCB - 32 Amp, 415 Volt, 4 pole, 25 KA with adjustable thermal & fixed magnetic protection/setting, Ics = 100 % Icu, thermal adjustable - 0.8 to 1 In, in accordance with IS/IEC 60068-2-6 standard.- 02 Each (b) MCB four pole of current rating 40 Amp, C curve - 01 Each Cont/-

Supply, installation, testing and commissioning of LT panel, outdoor type, floor mounted not less than of 1500 mm x 1650 mm x 450 mm IP -54 degree of protection suitable for 3 phase, 4 Wire system , 415 Volts, 50 Hz ,CPRI approved factory made having independent compartment for 100 Amps bus bar incoming feeder and each out going feeders of 32 Amp, dust and vermin proof, outer shell fabricated of 2 mm thick CRCA sheet & made out angle iron frame of 40 mm x 40 mm x 5 mm (for external) with seven tank treatment process for powder coating with thickness not less than 60 micron Cont/-

Cont/- provided with suitable gasket to make it dust/vermin proof & general construction confirming to IS 8063/93, pedestal flame grouted in PCC (1:2:4) type B-1 20 mm graded stone aggregate, thimble and cable entry boxes with cable glands including disconnecting and dismantling old LT panel of any size complete in all respect and comprising of the following: Inner Shell:- Inner shell made out of 1.6 mm thick CRCA sheet duly compartmentalised for each control gear, front lockable/openable by keys from both sides having chromium plated 19 mm dia fancy lock (02 Nos in each Cont/-

Cont/- neutral flow of air 'U' type completely vermin proof & to accomodate incoming/outgoing MCCBs and TPN aluminium bus bar of rating not less than 1.5 times of rated capacity of incoming MCCB. The colour coded heat shrinkable sleave for bus bar and shall be mounted on non hydroscopic, non combustible,track resistant, high strength FRP/SMC/DMC material at an interval not more than 250 mm throughout complete all as specified and as directed. Cont/-

Cont/- Incoming:- (a) MCCB - 100 Amp, 415 Volt, 4 pole, 36 KA with adjustable thermal & magnetic protection/setting, Ics = 100 % Icu, thermal adjustable - 0.8 to 1 In, magnetic adjustment - 5 to 10 In in accordance with IS/IEC 60068-2-6 standard. - 01 Each Outgoing:- (b) MCCB - 63 Amp, 415 Volt, 4 pole, 25 KA with adjustable thermal & fixed magnetic protection/setting, Ics = 100 % Icu, thermal adjustable - 0.8 to 1 In, in accordance with IS/IEC 60068-2-6 standard.- 02 Each (b) MCB four pole of current rating 40 Amp, C curve - 01 Each Cont/-

Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty electric cable with stranded aluminium conductor 1100 volts grade of cross sectional area 25 sq mm 3.5 core confirming to IS-7098 (Part-I-1988) complete all as specified and directed by Engineer-in-charge. Notes :- (i) Excavation, earth work, sand cushioning, cable protection and GI pipe if required, shall be measured & paid for separately under respective items of BOQ. (ii) Road cutting / floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall deemed to be inclusive of the above provisions.

Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty electric cable with stranded aluminium conductor 1100 volts grade of cross sectional area 16 sq mm 4 core confirming to IS-7098 (Part-I-1988) complete all as specified and directed by Engineer-in-charge. Notes :- (i) Excavation, earth work, sand cushioning, cable protection and GI pipe if required, shall be measured & paid for separately under respective items of BOQ. (ii) Road cutting / floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall deemed to be inclusive of the above provisions.

Supply and layinging reinforced precast concrete cable cover, class LV, Type 1 with peak, size 250X150x 40 mm complete all as specified and as directed by Engineer-in-Charge.

M&L for dry sand (Tibba sand) and punning for cushioning to underground cable complete all as specified and directed by Engineer-in-charge Note: - For payment purpose thickness after punning shall be measured.

Supply, installation, testing and commissioning of pumping header made of (approx length 4 mtr) with 150 mm bore GI flanged pipe, medium grade comparising the following :- (i) Provision of 1 Nos outgoing and two nos incoming distribution feeder/by pass pipe feeder suitable for 100 mm bore GI pipe Heavy class including all fitting including Provn of suitable size sluice valves. (ii) PCC foundation in CM 1:2:4 type B-2 using 20 mm graded aggregate for support of header pipe as per manufacturer specification. Note:- 1. Butterfly valve of any size required to be fixed in Header will be measure and paid separately. 2. Distribution /Bypass pipe lines 100 mm will be measured and paid separately under respective items from header.

Supply, installation, testing and commissioning of pumping header made of (approx length 4 mtr) with 100 mm bore GI flanged pipe, Heavy grade comparising the following :- (i) Provision of 01 Nos outgoing and two Nos incoming distribution feeder/by pass pipe feeder suitable for 80 mm bore GI pipe Heavy grade including all GI fitting including Provn of suitable size sluice valves (ii) PCC foundation in CM 1:2:4 type B-2 using 20 mm graded aggregate for support of header pipe as per manufacturer specification. Note:-(1) Butterfly valve of any size required to be fixed in Header will be measure and paid separately. (2). Distribution /Bypass pipe lines 80 mm will be measured and paid separately under respective items from header.

Supply, laying, jointing and testing only of GI tubing medium grade 25 mm bore with all fittings laid in trenches complete all as specified and as directed by Engineer-in-Charge. Note:- Excavation and earth work and joints shall be measured and paid separately.

Supply & fixing gun metal globe or gate valve with iron wheel valve head screwed both ends for iron pipe size 25 mm dia . ISI marked complete all as specified and as directed by Engineer-in-Charge.

Supply and installing monoblock pumping set suitable for 415 Volt having Capacity 1 HP, 50 Hz electric driven, complete inclusive of starter and PCC foundation complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning 01 Nos Pressure sand filter (PSF) cylindrical inner surface MS epoxy coated and external surface Red oide with blue color coated construction of size 2200 mm dia x 2000 mm (1700 mm + 300 mm free board), Shell thickness 6 mm and Dish end thickness 8 mm and rate of flow 40 m3/Hr and filteration velocity 10 Cum/sqm/hr complete with supporting layers of pebbles and graded quartz gravels as filter media as recommended by OEM not less than 7000 Kg ,complete internal piping distribution system as per Cont/-

Cont/- OEM Recommendation outer piping arrangement alongwith butterfly valves of suitable size upto inlet and outlet alongwith backwash arrangement with 80 mm dia heavy grade MS Pipe Flanged ends at inlet and outlet dualy painted with epoxy coated, red oxide, Air vent provision as per OEM Recommendation pressure guage etc complete all as specified and as directed by Engineer-in-Charge. Cont/-

Cont/- Note :- (i) PCC/RCC foundation as per manufacture recommendation will be included in quoted rates. (ii) MS pipe 80 mm dia epoxy coated and should not less than 10 RM for connections and fitting and Hammer butterfly valves not less than 05 Nos 80 mm dia is included in quoted rates. (iii) Any other item required for functioning of plant as per manufacturers recommendation is deemed to be included in the item rate and no extra payment is admissible on this account.

Supply, installation, testing and commissioning 01 Nos Pressure sand filter (PSF) cylindrical inner surface MS epoxy coated and external surface Red oide with blue color coated construction of size 1400 mm dia x 1800 mm (1500 mm + 300 mm free board), Shell thickness 6 mm and Dish end thickness 8 mm and rate of flow 15 m3/Hr and filteration velocity 10 Cum/sqm/hr complete with supporting layers of pebbles and graded quartz gravels as filter media as recommended by Cont/-

Cont/- OEM not less than 2500 Kg, complete internal piping distribution system as per OEM Recommendation outer piping arrangement alongwith butterfly valves of suitable size upto inlet and outlet alongwith backwash arrangement with 50 mm dia heavy grade MS Pipe Flanged ends at inlet and outlet dualy painted with epoxy coated, red oxide, Air vent provision as per OEM Recommendation pressure guage etc complete all as specified and as directed by Engineer-in-Charge. Cont/-

Cont/- Note:- (i) PCC/RCC foundation as per manufacture recommendation will be included in quoted rates. (ii) MS pipe 50 mm dia epoxy coated and should not less than 10 RM for connections and fitting and Hammer butterfly valves not less than 05 Nos 50 mm dia is included in quoted rates. (iii) Any other item required for functioning of plant as per manufacturers recommendation is deemed to be included in the item rate and no extra payment is admissible on this account.

Supply, installation, testing and commissioning 01 Nos activated carbon filter (ACF) cylindrical inner surface MS epoxy coated and external surface Red oide with blue color coated construction of size 2200 mm dia x 2000 mm (1700 mm + 300 mm free board), Shell thickness 6 mm and Dish end thickness 8 mm and rate of flow 40 m3/Hr and filteration velocity 10 Cum/sqm/hrcomplete with activated carbon (Gac), Coconut base, IV-900-2500 Kg layers of as filter media , complete internal piping distribution system as per Cont/-

Cont/- OEM Recommendation outer piping arrangement alongwith butterfly valves of suitable size upto inlet and outlet alongwith backwash arrangement with 80 mm dia heavy grade MS Pipe Flanged ends at inlet and outlet dualy painted with epoxy coated, red oxide, Air vent provision as per OEM Recommendation pressure guage etc complete all as specified and as directed by Engineer-in-Charge. Cont/-

Cont/- Note:- (i) PCC foundation as per manufacture recommendation will be included in quoted rates. (ii) MS pipe 80 mm dia epoxy coated and should not less than 10 RM for connections and fitting and Hammer butterfly valves not less than 05 Nos 80 mm dia is included in quoted rates. (iii) Any other item required for functioning of plant as per manufacturers recommendation is deemed to be included in the item rate and no extra payment is admissible on this account.

Supply, installation, testing and commissioning 01 Nos activated carbon filter (ACF) cylindrical inner surface MS epoxy coated and external surface Red oide with blue color coated construction of size 1400 mm dia x 1800 mm (1500 mm + 300 mm free board), Shell thickness 6 mm and Dish end thickness 8 mm and rate of flow 15 m3/Hr and filteration velocity 10 Cum/sqm/hrcomplete with activated carbon (Gac), Coconut base, IV-900-925 Kg layers of as filter media , complete internal piping distribution system as per Cont/-

Cont/- OEM Recommendation outer piping arrangement alongwith butterfly valves of suitable size upto inlet and outlet alongwith backwash arrangement with 50 mm dia heavy grade MS Pipe Flanged ends at inlet and outlet dualy painted with epoxy coated, red oxide, Air vent provision as per OEM Recommendation pressure guage etc complete all as specified and as directed by Engineer-in-Charge. Cont/-

Cont/- Note:- (i) PCC 1:2:4 foundation as per manufacture recommendation will be included in quoted rates. (ii) MS pipe 50 mm dia epoxy coated and should not less than 10 RM for connections and fitting and Hammer butterfly valves not less than 05 Nos 50 mm dia is included in quoted rates. (iii) Any other item required for functioning of plant as per manufacturers recommendation is deemed to be included in the item rate and no extra payment is admissible on this account.