GF 2025-2026

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS 20B and Sand, silt or other loose soil, wet sand, silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and completed, cleaning and levelling the site etc., complete - Narrow Foundations - First Depth Upto 2.00M

Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at not more than 75cm centre to centre etc. complete complying with the standard specificaiton. - For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requirements of IS standards. - Upto Basement

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Supplying and filling the basement with Good carted Earth 5km away from the site and filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification.

Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9"X43/8"X 23/4" standard specification including finishing, curing, etc., complete complying with standard specification (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost).

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Plastering with cement mortar 1:5 (One cement and five plastering sand (P- Sand)) 12mm thick in all floors including cost and conveyance of all materials to site etc,complete as per standard specifications

Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections.All the materials should be got approved by the Engineer - In -charge before fixing as directed.

Supply and fixing of Stainless steel (Salem stainless steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc.complete as per standard specification.

Supply & fixing of Ano. Alu. Fixed window with three panels using 62x38x2 mm @ 1.174 kg/m thick extruded box section as verticals and horizontal member and fixing 4mm thick plain / frosted/ pin headed glass approved quality with necessary glazing clips, rubber beading etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish usder electrically condition in accordance with ISI1868/1962 specification for an average anodic film thick of not less than 15 microns.

Plain Cement Concrete 1:1.5:3 (one cement, one and half Commercial Sand (M- Sand) and three coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges etc., complete as per standard specification

Paving the floor with pre-polished Cement based hydrualically pressed Anti-Skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three plastering sand (P- Sand)) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg/sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position Cement based hydrualically pressed Anti-Skid tiles (pattern design) 20mm thick in cement mortar 1:3 (one cement and three plastering sand (P- Sand)) 20mm thick and pointing with white cement using at the rate of 0.40kg/m2 including finishing joint with tile surface etc., complete complying with standard specificaiton and as directed by the departmental officers

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three plastering sand (P- Sand)) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Supply and fixing Perculated gypsum board false ceiling using 18 mm thick of approved Quality and design suspended from the ceiling using ‘U’ shaped Galvanised Iron channel of size 25 x 25 x 0.55 mm thick at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing ‘U’ shaped G.I. Channel of size 50 x 30 x 0.55 mm thick at 0.60 m centre to centre on cross direction and fixing of ‘U’ shaped G.I. channel of size 50 x 10 x 0.55 mm thick at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W. reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design/pattern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using kit ply 12 mm thick and opening should be covered with Acrylic panel etc. complete complying with standard specification and as directed by the dept officers. All the materials should be got approved before use work.

Painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first quality and of approved colour over a priming coat including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required etc., complete complying with standard specification.

Painting the new iron work with two coats of best pproved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat and including cost of painting materials, brushes, putty, preparation of surfaces and scaffolding charges etc., complete complying with standard specification and as directed by the departmental officer.

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of 110mm dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). SD 23

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 54

Supplying and fixing of 1200mm ( 48'' ) sweep AC ceiling fan complete with regulator with 1M down rod including S & F of fan clamp with side plates and cross arm SD 107

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC power plug point.SD 40

Supply and fixing of AC / DC 76mm Buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW Board with push switch SD 105

Supply and fixing of 20 Amps DP plug and socket in sheet enclosure with 32 A DP MCB in flush with wall with earth connection for AC plug SD 144

Supply and fixing of 3Nos 5 Amps (3 pin and 2 pin ) compined flush type wall socket with control switches concealed in suitable TW Box covered with Hylem sheet in flush with wall earth connection for Computer plug socket SD 142

Supply and run of 2 of 4sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG Cu wireand making good of the concealed portion with suitable colour (SD57)

Supply and run of 20 pair telephone wire in PVC Condiut insulated unsheathed etc, complete as per standard specifications.

Supply and run of CAT 6 LAN cable in pvc conduit in PVC Condiut insulated unsheathed etc, complete as per standard specifications.

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962 and should be got approved by the Executive Engineer before use.

Supplying and fixing the 5 star rated (Carrier/ Voltas /"O" General or equivalent) Split A/C machines of 2.00 tons capacity of ISI make with Supply and installation of 5 KVA capacity Automatic Voltage Stabilizer with time delay relay, Supply and fixing of MS stand for fixing outdoor unit, Supply and fixing of 3m length water drain pipe line (1” PVC Pipe) and all other necessary accessories as instructed by the Departmental officers etc complete as per standard specifications

Supply and fixing of LED 4000K 2 X 2 square type Recessed fitting (Phillips / Havells / equivalent) etc, complete as per standard specifications.

Supply and fixing of 18W LED 3000K square type Recessed fitting (Phillips / Havells / equivalent) etc, complete as per standard specifications.

Manufacturing, Supply and delivery of table size 2400mm X 1200mm X 750mm, using 18mm thick Antitermite water proof ply and top of table should be covered with laminated partice board, with drawers and cabinets with necessary accessories and two coats best varnish on the inside of the table and the sides of plywood should be lipping with teak wood beading and with two coats of varnish etc., complete. All the materials to be used should got approved by the departmental officers before use on work. The rate includes cost of materials labour charges, conveyance, neat finishing, fixing etc., complete complying with standard specification and as directed by the departmental officer.

Manufacturing, Supply and delivery of Computer table size 2400mm X 525mm X 750mm, using 18mm thick Antitermite water proof ply and top of table should be covered with laminated partice board. The keyboard tray shall be of size 710mm (front width) X 300mm (depth) approximately is to be provided with end fittings made from minimum 2mm thick MS steel mounted on either side and the keyboard tray shall be easily slideable, provided with two telescopic channels with balls. The size of the open area for CPU should be 200 mm (W) x 400 mm (D) x 500 mm (H).The Cost shall incluidng drawers and cabinets with necessary accessories and two coats best varnish on the inside of the table and the sides of plywood should be lipping with teak wood beading and with two coats of varnish etc., complete. All the materials to be used should got approved by the departmental officers before use on work. The rate includes cost of materials labour charges, conveyance, neat finishing, fixing etc., complete complying with standard specification and as directed by the departmental officer.

Manufacturing, Supply and delivery of table size 1500mm X 750mm X 750mm, using 18mm thick Antitermite water proof ply and top of table should be covered with laminated partice board, without drawers and cabinets but including necessary accessories and two coats best varnish on the inside of the table and the sides of plywood should be lipping with teak wood beading and with two coats of varnish etc., complete. All the materials to be used should got approved by the departmental officers before use on work. The rate includes cost of materials labour charges, conveyance, neat finishing, fixing etc., complete complying with standard specification and as directed by the departmental officer.

Manufacture and supply of council hall chairs with using superior quality Nigerian teak wood, hand crafted by skilled artificiants with premium finishing. Seat & back is made up of the luxurious high density foam covered with jute textured premium cotton cloth and the colour and quality as directed. All the materials to be used should got approved by the departmental officers before use on work. The rate includes cost of materials labour charges, conveyance, neat finishing, fixing etc., complete complying with standard specification and as directed by the departmental officer.

Manufacture and supply of S- Type ordinary chair for office use with MS pipes normal finishing . Seat & back is made up of the PVC wire mesh and the colour and quality as directed. All the materials to be used should got approved by the departmental officers before use on work. The rate includes cost of materials labour charges, conveyance, neat finishing, fixing etc., complete complying with standard specification and as directed by the departmental officer.

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Add gst 18%

Nimalan Enterprises (BID ID -1418176)