PROVN OF ANNEXE NEAR BLDG NO P-07 MANEKSHAW MARG AND FACILITY CENTRE AT ECHS BHAWAN DELHI CANTT-10

Amount

M & L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavated materials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

M & L for Hard core of gauge exc 63mm but not exc 100mm deposited spread and leveling in layers n exc 15cm thick water and raming to a true surface complete all as specified and directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base complete all as specified and as directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and similar work; vertical or to batter complete all as specified and directed.

M & L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular rough finished surfaces of concrete laid flat complete all as directed.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M & L for form work to soffits of suspended slabs such as roof slabs, floor, slabs landings and stair and similar work not exc. 20 cm thick flat rough to receive plaster all as specified and directed.

M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete.

M & L for mild steel TMT bar 10mm dia and over cut to length,bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 13 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M & L for RCC M25 Design Mix using 20mm graded agg as in footings, plinth beam and bases of columns complete all as specified and as directed.

M & L for RCC M25 Design Mix using 20mm graded agg as in beams,lintle/plinth bands cantilevers, bressumers, lintel over 1.5m clear span supported on walls complete all as specified and as directed.

M & L for RCC M25 Design Mix using 20mm graded agg as in columns , piers posts and struts complete all as specified and as directed.

M & L for RCC M25 Design Mix using 20mm graded agg as in slabs, supported on walls, landings, balconies and in shelves and the like complete all as specified and as directed.

M & L for brick work in CM 1:6 using Sub class "B" bricks straight or curved on plan exc. 6mmean radius complete all as specified and as directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 finished even and smooth without using extra cement including a mix of water proofing compound @ 200ml/50Kg Cement Bag (Smartcare vitalia of Asian Paint product or equivalent of Berger and Nerolac), complete all as specified and as directed. (Note : Cost of water proofing compound shall deemed to include in the quoted rate).

Providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Make: SmartCare Damp Proof of Asian Paints or equivalent in Berger and Nerolac. Notes: (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) All materials shall be procured directly form manufacturer. (4) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position incl scafolding etc, complete all as specified.

M & L for 15mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position incl scafolding etc, complete all as specified.

M & L rendering 10 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and smooth without using extra cement including complete all as specified and as directed.

S & F plain gypsum board panel 12 mm thick on ceiling with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm including two coat of OBD over a coat of chalk whitening putty complete all as specified and directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer applied and 1mm thick wall care putty over new surfaces complete all as specified and as directed.

M & L Preparation of newly plastered /unplastered surfaces of walls and ceilings over 1mm thick Birla White/J K White wall care putty, again sand papering thus making surface good and applying Two coats of Oil Bound Distemper on wall surfaces over a coat of primer ,complete all as specified and directed.

M & L for Preparation of New plastered or unplastered surfaces of walls and applying Texture Painting on Wall/Ceiling of various pattern/design over a coat of wall primer and 1mm thick wall care putty JK or Birla complete all as specified and as directed.

S & F for Preparation of New plastered or unplastered surfaces of walls and applying wall paper on Wall/Ceiling of various pattern/design over a coat of wall primer and 1mm thick wall care putty JK or Birla complete all as specified and as directed.

S & F for 1st class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S & F for Factory made door shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS: 1003(Part 1), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F for Factory made window with side hung shutters with glazing beads, shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels)of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per SSR Part I, Section 8 clause 8.24(b), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F for Factory made window with side hung shutters without glazing beads, shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels)of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per SSR Part I, Section 8 clause 8.24(b), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F 35mm thick 1st class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. devided into squres with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples include for fixing with beads.

S & F 5.5mm thick tinted glass sheet glass glazing with oil putty in squares n exc 0.5sqm in each panes complete all as specified and as directed.

M&L Preparation of new wooden surface and applying polish for a glossy finish over 10cm width or girth, complete all as specified and as directed.

S & F 150mm size brass butt hinges complete all as specified.

S & F 150 mm long brass barrel tower bolt, fixed complete all as specified and directed.

S&F 300 mm long brass coated sliding door bolts, plate type, stove enamelled black, with brigh bolt not less than 12 dia with and incluidng 1 minimum of 6 bolts and nuts four or bolt plate and tow on staple plate complete all as specified.

S & F 150 mm long brass handle oval type, complete all as specified and as directed.

M & L for Designer type wall panel of minimum thickness not less than 12mm (Pattern and design as approved by GE) inclusive of fixing to wall incl moulding end caps fixed with PVC sleeves and screws as required at site complete all as specified and as directed.

Supply and fix for frame work such as grill, grating etc with ends bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors and similar work confirming to Fe 290 Gde E-165 complete all as specified and directed.

M&L two coat of synthetic enamel paint (finishing coat) over one coat of primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M & L 20 mm thick granite (Z black colour) of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over and incl rendering/ screed bed 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding complete all as specified and as directed .

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and smooth without using extra cement, complete all as specified.

M & L for Vitrified coloured ceramic tiles light shade 10mm thick, square/rectangular(with pattern and boarder work as required at site), area of tiles exceeding 0.42Sqm and not exceeding 1.50Sqm each tiles as in flooring over 15mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match over or filling spacers as per requirement at site or as directed including designer tiles pattern work between the tiles complete all as specified and as directed by Engr-in-Charge or GE, complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M & L for wall cladding tiles of size area exc. 0.18 sqm but n.exc 0.60 of 8-10mm thick on vertical surfaces of wall over and incl 10mm thick screed bed in CM 1:4 complete all as specified and as directed and sample approved by GE (Make : Unistone/ultra/Coral/Somany/Kajaria).

M & L for Wooden coloured interlocking tiles (Wooden Flooring) 1215mm x 168mm x 8mm thick rectangular fixed in floor/dado laid over existing floor with foam sheet of approved best quality including joint/end covering strip including all other fixing materials complete all as specified and directed. Make : kajaria catlog No AC 3 or equivalent in Cera/Somany.

M & L for glazed coloured ceramic tiles in vertical surface area of each tile exc 0.18 Sqm but n exc 1.08 Sqm (with pattern and border work as required at site) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick rendering in CM 1:4 complete all as specified and as directed.

S&F 15mm dia GI tubbing medium grade with all fitting and fixed to wall and ceiling or laid in floors etc incl scafolding, cutting chases in wall where ever required etc complete, all as specified.

S&F 20mm dia GI tubbing medium grade with all fitting and fixed to wall and ceiling or laid in floors etc incl scafolding, cutting chases in wall where ever required etc complete, all as specified.

S&F bib taps, (Long body) cast copper alloy fancy type, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe15mm bore all as specified and directed. Make & Cat Part : Jaquar-Cat No. CON-047KN, Jaquar-Cat No. CON-107KN, Kohler-Cat No.K-37341IN-4-CP

S & F 1000 ltr capacity rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia PTMT ball valve valve complete all as specified.

S & F for 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover CP jet spary, Health Faucet, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed. (Make : Jaquar or equivalent in Cera/Parryware).

S & F Vitreous china wash basin counter oval type size 600x425x195mm, under granite slab with all fitting and fixture complete all as specified and as directed. (Make : Jaquar or equivalent in Cera or Parryware).

S & F Vitreous chinaware table top wash hand basin (WHB) of size 595mm x 440mm x 185mm complete including 32 mm dia chromium plated waste coupling, PVC waste pipe etc., complete all as specified and as directed. (Make : Jaquar or equivalent in Cera or Parryware).

S & F Brass CP basin mixer central hole, sensor type , for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions complete all as specified and directed. Make & Cat Part : Jaquar-Cat No. SNR-1501-7PMPK, Jaquar-Cat No. SNR-15017PM, Kohler-Cat No. K-18656IN-ND-CP.

S & F Brass chromium plated wall mixture 3 in 1 system with provision for hand shower and overhead shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. CON-281KN, Jaquar-Cat No. COP-281PM Kohler-Cat No. K-98754IN-4-CP.

S & F wall mounter multiple function Shower panel including all fittings and fixtures as per product code make Jaquar/Hindware description below :- (a) Item Product code 511686 (Size-1650mmx150mmx550mm) - Make-Hindware. (b) Item Product code JPL-SSF-ST88148B. (Size-1600mmx 200mm)- Make-Jaquar. (c) Item Product Code JPL-WHT-TMCURVENEO. (Size-1500mmx230mm)-Make-Jaquar

S&F Ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated, fixed in repairs, complete all as specified and as directed. consisting of the following combination :- (a) Wash Hand Basin 810mm x 500mm. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. (d) Mirror cabinet size 780mm x 160mm x 800mm. Make : Hindware - Cat Part No. 70089 or 70084/ Kohler : Cat Part No. K-31602IN-E63

S & F Angle valve of CP high pressure screwed for iron pipe and fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F Two way Angle cock 15mm bore dia or pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S& F Brass chromium plated towel rack of size 600 mm x 350mm, fixed with brass screws, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F PVC (SWR) Floor/Nahani trap, plain dia of outlet 125mm, complete all as specified and as directed.

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, complete all as specified and as directed.

S & F CP toilet paper holder fixed with plug and brass screws, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S&F 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals and Sink etc all as specified and directed.

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

Fabrication & fixing of Modular wardrobe/ cupboard made out of 18-20 mm thick HDHMR boards with 2.00mm thick fabric colour laminate sheet of approved quality and texture on all exposed sides with edge band including providing cabinet for keeping baskets/ drawers etc. complete all as specified and as directed. (Design and pattern as approved by GE). (Make : Rajshree or equivalent)

S & F for 18-20mm thick HDHMR boards with laminated fabric colour on both sides, fixing in partitions of Modular kitchen cabinet & wardrobe/ cupboard complete all as specified and as dirfected. (Make : Rajshree or equivalent)

S & F for Continuous piano type hinges, stainless steel with width of flaps 30mm, complete all as specified and as directed.

S & F for Fancy type Stainless steel bright polished handles oval type of size 150mm size, complete all as specified and as directed.

S & F 50mm size cup board locks of brass, 2 levers including keys set, complete all as specified and as directed.

S & F for Magnetic catches with steel body ‘H’ type, fixed to shutter, complete all as specified and as directed.

S & F for Hettich soft closure hinges of premium quality, fixed in door/cup board shutters complete all as specified and as directed

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 200 mm dia SGSW pipe complete all as specified & directed.

S&F 200mm internal dia of SGSW pipes laid in trenches and jointed with cement mortar 1:3 complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 200 mm bore drain pipe complete all as specified and as directed.

S & F for Stainless steel work grade 304 (as in vertical post, hand rails, railings in gallery, purlins, including special shaped, washers horizontal/vertical) fixed/welded in any position etc., complete using stainless steel fittings, notching, drilling, grinding, fitting cleats, fish plates, gusset plates, etc., complete all as specified and as directed.

M & L for Sliding/openable glass door 12mm thick (toughened glass) of approved quality including necessary all stainless steel powder coated hardware fittings (As like sliding rail, guide, clips, frame , brackets , clits , jammers, stopers, locking arrangement etc) door fixed with floor spring, with two No's stainless steel handle on each leaf/door n exc 30 cm long 25 mm thick complete drilled for fixing with all fitting and fixture complete all as specified and as directed.

M & L for 12mm thick (toughened glass) of approved quality fixed in any position (partition, bathroom enclosure and the like)including necessary all stainless steel hardware fittings (As like frame, brackets, clips, jammers, stoppers. etc.) complete drilled for fixing with all fitting and fixture, complete all as specified and as directed.

S & F painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L for Glossy finished Designer Coloured Chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over and incl 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for PU Moulded glossy finished Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid over 50mm thick sand cushioning, laid duly mainting propper slope as per requirement at site over hardstanding/path complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm, watering and removing of surplus soil to a distance not exc 50m and making good surfaces, complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 complete all as specified and directed

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position complete all as specified and directed.

S & F 110mm bore PVC (SWR) bends any radius complete

S & F Stack clamps out of 50 mmx 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for bore of pipe 100mm complete.

S & F 110mm PVC (SWR) vent cowl complete.

M&L Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

M&L Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete.

S & F Aluminium alloy powder coated standard hollow section for ventilotors as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and as directed.

S&F Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 2mm in vertical and horizontal members and glazed with 5mm thick tinted glass and 12mm thick prelaminated particle board interior grade with laminations on both faces as directed by Engr-in-Charge according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement, complete all as specified and as directed.

S&F UPVC designer type frame for fixing of glass in doors/ windows of any shape, size and thickness as required at site (Design and pattern as approved by GE) complete all as specified.

Anti termite treatment for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per Sqm of surface area complete all as specified and as directed.

M & L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid over 50mm thick sand cushioning, laid duly mainting propper slope as per requirement at site over hardstanding/path complete all as specified and as directed.

M&L Soakage well of size 3.0mtr dia and 4.5mtr effective depth including excavation in any type of soil and removal of soil not exceeding 50mtr and depositing, PCC 1:3:6 type C-2 using 40mm graded curshed stone aggregate as in foundations, honey combed brick work in one brick wall in cement mortar 1:4, RCC M-25 Design mix using 20mm graded aggregate in top ring beam and cover slab, with SFRC manhole covers and intercepting chamber and screen chamber and making connections of RCC/DWC pipes and loose filling of brick aggregate of gauge 63mm, complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers and including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box and cover plate for fixing of moduler of suitable sizes for fixing modular switches/sockets/fan regulator etc , with Modular plates of suitable size complete all as directed for the following :- (a) one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

All as per Srl item No. 105 here in above but for four light point controlled by one one-way switch

All as per Srl item No. 105 here in above one socket outlet point 5 amps on the same board.

All as per Srl item No. 105 here in above but one socket outlet point 5 amps on the independent board.

All as per Srl item No. 105 here in above but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for socket point on independent board

S&F Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F Modular bell switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.

S&F Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.

S&F Modular socket 6/16 Amp multipurpose type, 2 module size complete all as directed.

S&F Modular Fan regulator step type, 120 watts complete all as directed.

S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps complete all as directed.

S&F Bell ding dong AC 240 V 50 Hz complete all as specified and as directed

S & F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 20 Watts, cool/warm white as per site requirement complete all as specified and directed..

S & F fancy LED energy efficient integrated fittings, metal extruded in golden frame, 10 Watts, mirror light cool/warm white as per site requirement complete all as specified and directed..

Supply and fixing LED ceiling light fitting 10 watt, in round shape, surface/recess type cool/warm white with inbuilt driver as per site requirement and making all electric connections complete all as directed. Make :Make:-Havells/Bajaj/Philips/Wipro/Syska/Fiem/Polycab

Supply and fixing LED ceiling light fitting 6 watt, in round shape, surface/recess type cool/warm white with inbuilt driver as per site requirement and making all electric connections complete all as directed. Make :Make:-Havells/ Bajaj/ Philips/ Wipro/ Syska/ Fiem/ Polycab

S&F ceiling fan complete with blades, down rod,and accessories 230V 1200 mm sweep, minimum air delivery 210CFM with service value 6.00 BEE, five star rated with brushless direct current motor without remote complete all as specified.

Supply and fixing Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections complete all as directed.

Supply and fixing Ventilating fan 200 mm sweep plastic body type including self closing louver and making all electric connections complete all as directed.

S & F fancy LED energy efficient integrated fittings, metal extruded in golden frame, 5/6 Watts, bed light with flexible cord cool/warm white as per site requirement complete all as specified and directed..

S&F fancy Wall bracket fittings suitable for cool/ warm white retrofit LED bulb with base B22 holder complete all as specified and as directed

Supply and fixing Geyser 25 ltre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners for hanging and CP and PVC connection for inlet and outlet upto stop cock complete all as specifed and directed.

M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into PVC concealed conduit 25 mm dia medium grade with all fittings and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

M&L Sub main wiring with 2 run of 4 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed

S&F distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 12 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed

S&F Modular AC Socket with 25 Amps SP mini MCB, 230 Volts, 50Hz. In 4 module sheet metal enclosure complete all as specified and as directed.

S&F MCB SP, C Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F Isolator SPN, 40 Amp, 240V complete all as specified and as directed

Supply and fixing high pressure booster pump with 8 ltr capacity pressure tank, coupled with electric motor of capacity 0.98 HP, 230 volts, single phase, 50 Hz incl Pressure Guage, Pressure switch & connecting accessories of GI i.e bend, nipple, socket, tee of requisite size etc incl cutting of existing pipe complete all as directed

S & F energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

Supply and fixing street light fitting bracket, 1.0 mtr long made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Supply and fixing Flexible LED strip light tubular type, cool/warm white , incl LED AC to DC adopter and making all electric connections complete all as directed.

Supply and fixing AC to DC adaptor for LED strip light tubular type complete all as specfied and as directed

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

M&L XLPE insulated armoured heavy duty electric cable with aluminium conductor ,1100 volt, size 35 sqmm 3.5 core complete all as specified and as directed.

M&L HDPE DWC pipe 50mm internal dia fitting on wall/surface with clamp for passing cable ,complete all as specified and as directed.

Supply and fixing lamp holder PVC/ polycarbonate type suitable for batten fittings complete all as directed.

S & F LED simple batten fittings 10Watts, cool/warm white complete all as specified and directed..

S&F of Recess/Surface mounting 2'x2' square flat panel ultra slim scoop LED light 36 watt warm/cool white with driver etc suitable for Grid ceiling/Gypsum board/POP ceiling incl making electric connection complete as as directed.

Supply and fixing of Ventilating fan 250 mm sweep plastic body type including self cosing louver and making all electric connections complete all as directed.

S&F of LED bulk head fitting 10 watts made of cast aluminium alloy with opal glass diffuser complete all as specified and directed.

Supply and fixing of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections complete all as directed.

Supply and fixing of MCCB 3 pole ,415 V fixed type 100Amp with breaking capacity 16KA.

M&L for Sub main wiring complete with 2 X 4.0 Sqmm(nominal area) FRLS,PVC insulated unsheathed multistranded copper conductor cable ISI marked, and 1 x 4 sqmm as earth wire in and including PVC casing caping 25 mm min, heavy duty double lock,and casing fitting such as tees,bends,elbow etccomplete all as specified and as directed.

S & F switch piano ,flush type single pole one way 15 Amp complete all as directed

S & F socket outlet,3pin , 15 Amp flush type complete all as directed.

PVC Gang Box suitable for one No 15 Amps Switch and one No 15 Amp Socket complete all as specified and as directed.

Supply and fixing PVC connection 600 mm long with C P brass adapter 10 mm dia with washer for inlet & outlet pipe, ISI marked for gyser complete all as directed.

S&F 15 mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, chromium plated and fixed complete all as directed

Supply and fixing 15 mm Angle stop valve of any colour high pressure screwed for iron pipe and fixed complete all as directed.

Material and labour for laying of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100Volt grade cross sectional area 16 sqmm 2 core complete all as specified and as directed

Material and labour for brick protection to cable using old size class 'B' bricks, laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as directed.

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as directed.

M&L of GI pipe medium grade 40 mm bore all fittings fixed to wall or laying under path/ road complete all as specifed and directed.

Providing and fixing factory made uPVC white/Off colour casement (Openable) door made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + –0.2 mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated). Corner strikers Secondary striker, Cylinder. Door transmition gear made of mild steel with multi point locking system with strikes] 3D hinges of zinc alloyed (white powder coated) and 8mm thick tinted/frosted glass. (Note: The unit rate quoted by contractor include cost of glass and all other connected accessories. Net opening will be measured for payment purpose.)

Providing and fixing factory made uPVC white/Off colour casement (Openable) door made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + –0.2 mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated). Corner strikers Secondary striker, Cylinder. Door transmition gear made of mild steel with multi point locking system with strikes] 3D hinges of zinc alloyed (white powder coated) and with stainless steel wiremesh (0.36mm nominal dia of wire and average width of apreture 1.40mm. (Note: The unit rate quoted by contractor include cost of glass and all other connected accessories. Net opening will be measured for payment purpose.)

Anti termite treatment for treating the backfill in contact with foundation at the rate of 7.5 liters of emulsion per square meter of vertical surface (area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

Anti termite treatment for treating the top surface of filed earth at the rate of 5 liters of emulsion per square meter of surface complete all as specified and as directed.

Anti termite treatment for treating the soil under plinth protection at the rate of 5 liters of emulsion per square meter of surface area complete all as specified and as directed.

S&F of ceiling fan complete with blades, down rods, and accessories, 230 volt, 1400mm sweep complete all as specified.

VIKRANT CONSTRUCTION CO.

The new hut furnitures

imran construction company

garnet engineers contractors