SPL REPAIR SINGLE OFFRS ACCN BLDG NO P-16 AT B MESS UNDER AGE B/R-II AT GE JHANSI

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr interval in length and joints between wall and plinth, laid to slope 1:30 incl forming joints 10mm wide and duly filled with proportion of mastic bitumen and sand in 1:3 (01 part bitumen mixed with 03 parts of sand) complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.

M&L for joint free, Vitrified Ceramic tiles of light shade 9-10 mm thick (square/rectangular) polished , area of each tile exc 0.42 but n.exc 1.00 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

All as per Ser item No 4 above but in skirting over and including 10mm thick CM backing coat in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed.

All as per Ser item No 08 above but not exc 1.5 sqm each complete all as specified and as directed.

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension,including 6 mm thick full length fancy type toughned glass, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed. Note: (a) UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (b) The quoted rates are deemed to be inclusive of toughned fancy glass and 3D hinges with aluminium hardware

Supply and fixing factory made uPVC white colour fixed glazed ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, including 6 mm thick full length toughned glass, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction. Note: (a) UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (b) The quoted rates are deemed to be inclusive of toughned fancy glass

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. including 6 mm toughned full length fancy type glass and wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed. Note: (a) UPVC frame sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (b) The quoted rates are deemed to be inclusive of glass and Aluminium wire mesh

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed. Note:- (a) The quoted rates are deemed to be inclusive of coloured glass and Aluminium wire mesh

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners incl in this item of required dia and length complete all as specified and directed.

M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

Removing existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime coba /brick layer etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush including removed rubbish from site complete all as specified and directed.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions laid with torch application complete all as specified and directed with following course of description below:- (a) 10 mm thick plaster in CM 1:4 with WPC (liquid water proofing compound @ 0.20 Ltr/bags(50 Kg Bag)) will be applied over the roof slab (subjected to condition as mentioned in notes) . After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based grout. After the surface is repaired the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/Sqm to be applied on prepared surface, till the surface is propely impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (f) after apllication of APP membrane one coat of aluminium paint @ 0.20 Kg/Sqm over APP membrance will be applied. Note : The cost of all items i.e. from Sr No. (a) to Sr No.(f) are included in quoted rate and no separate payment will be done for the above except liquid WPC.

Supply only liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed. Make : Dr Fixit LW+

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush and removing rubbish from site complete all as specified and directed.

M&L PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in mass filling in sunken portion complete all as specified and directed.

M&L for 25 mm thick ,type B-1 ,PCC 1:2:4 using 20mm graded stone aggregate as in padding , levelling course etc with liquid water proofing solution finished even and fair with proper slope as prepatory works to water proofing treatment complete all as specified and directed. Note:- liquid water proofing solution shall be provided in 200 ml in 50 Kg of cement by weight and cost of liquid water proofing solution measured and paid seperate item

M&L for 10mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 200 ml in 50 Kg of cement by weight and finished even and smooth without using extra cement complete all as specified and directed. Note:- liquid water proofing solution shall be provided in 200 ml in 50 Kg of cement by weight and cost of liquid water proofing solution measured and paid seperate item

M&L for application/forming of waterproofing liquid membrane on moistening the prepared surface for proper dispersion and penetration and applying two component cementitious elastomeric water proofing coating damp block 2k as per manufacturers specifications.The treatment shall be carried out to the entire bottom surface and vertical surface upto the bottom height of wall tiles. Adequate curing to be done on vertical surfaces and ponding test for 48 hours on the bottom surface to be carried out complete all as specified and directed. NOTE : (a) Treatment shall be done through authorised applicator/representative of the manufacturer only. (b) Warranty for water proofing to be submitted by the contractor as per manufacturer norms

M&L for Polythene film black 50 micron laid in floor complete all as specified and directed.

M&L for 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as specified and directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

M & L 25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description complete all as specified and directed. Note: (a) stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately (b) The quoted rates are deemed to be inclusive of 2mm thick , 25mm wide PVC edge binding tape of approved quality including necessary sythetic resin hot pressed to edge on binding machine

M & L 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description complete all as specified and directed. Note: (a) stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately (b) The quoted rates are deemed to be inclusive of 2mm thick , 18mm wide PVC edge binding tape of approved quality including necessary sythetic resin hot pressed to edge on binding machine.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 40 mm, complete all as specified and directed

S & F brass drawer/shutter handles fancy type , projection drop (50mm to 65mm) on screwed platey complete all as specified and directed

Supply and fix glass sliding shutter for Showcase /Bar using 5.5 mm transparent thoughned glass , aluminium two track rail all around the glass fixed with SS screw, including S S roller assembly for movement of glass shutter , including all necessary accessorries required for horizontal movement of two track glass shutter complete all as specified and directed

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, ISI, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. Note:- The quoted rates are deemed to be inclusive of glass and hardware etc

S&F in replacement of premium quality corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as specified and directed.

M&L in repair for SS curtain rod 25mm dia with fancy caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed. Note: Bracket and end caps/lobs are included in quoted rate.

S & F in repair chromium plated shower rose 150 mm size fancy type with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in replacement of 1st quality health faucet with 8 mm dia, 1.0 mtr long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in replacement of 3-in-1 wall mixer 1st quality with provision for overhead Shower with 115mm long bend pipe on upperside, connecting legs & wall flanges made of cast copper alloy, chromium plated fancy type, complete all as specified and directed.

S&F in repair vitreous china table top wash basin (1st quality) white or off w/o rim including single lever extended body swan neck basin mixer pillar tap suitable for table top wash basin , CP waste copling and CP bottle trap complete all as approved by Engr-in-charge and directed. Notes: Swan Neck Pillar Tap, Bottle Trap, Waste coupling , connection pipe, outlet pupe are included in quoted rate.

Supply & Fix in repairs Vitreous China wash down water closet pan (single unit, means one pieceof EWC with flushing cistern) white or off white coloured including matching coloured seat covered fixed, complete all as specified and directed.

S&F in replacement of towel rack 600 mm long fancy type with wall bracket made of cast copper alloy, chromium plated, complete all as specified and directed.

S&F in replacement of 1st quality PVC multipurpose cabinet mirror having inbuilt shelf to accommodate daily routine items with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

M&L for 15 to 18mm granite of any type table rubbed and polished for wall lining , window/door cill, counter for WHB , window jamb etc and over 10mm thick in cement mortar (1:4) and pointing with white cement using marble dust with admixture of pigment to match with shade of granite including rounding the outer/exposed edge complete all specified and directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work inlcuding removing of demolished material from site complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20 mm stone agg) as in Chajja supported on walls, beams and columns in roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for mild steel deformed TMT bars 10mm dia and over (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L for rough finish formwork to soffits of suspended slabs such as roof slabs, floor slabs and lintels, landing and similar work n exc 200mm thick complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick /concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 and 2nd coat 5 mm thick in CM 1:4 with WPC with 200 ml in 50 Kg of cement by weight on fair faces of brick work/concrete surfaces, finished even & smooth without using extra cement on brick or stone wall,dado and skirting etc complete all as specified and directed. Note: liquid water proofing solution shall be provided in 200 ml in 50 Kg of cement by weight and cost of liquid water proofing solution measured and paid seperate item

M&L for 10 mm rendering thick in CM (1:4) on fair faces of brick /concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:3) on fair faces of concrete surfaces in ceiling finished even & smooth without using extra cement on brick or stone wall,dado and skirting etc complete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper/interior acrylic emulsion and over a coat of primer incl a layer of 1mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and directed.

M&L for preparation of surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for preparation of new plastered of ceiling surface and applying three coats of white wash on new plastered surface , complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of primer including a layer of (JK/Birla) 1mm thick wall care putty to get smooth and level finish, complete all as specified and directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated ceiling surfaces and applying three coats of white wash on old plastered surface of ceiling surface, complete all as specified and as directed.

S&F SS grating of round shape 125mm dia floor trap traps etc, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M & L for 595 x 595mm in size machine cut kota stone slab flooring 18-20mm thick and over 20mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing (Mirror Polishing) complete all as specified and directed.

M & L for machine cut kota stone slab 15-18mm thick in riser of steps, skirting, dado and pillar laid over10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing complete all as specified and directed. Note: The quoted rates are deemed to be inclusive of kota stone in Step will be placed in single piece with groove lines at edge and moulded

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, andover 50mm thick sand cushioning, including CM (1:3) to stopper at edges of pavers, complete all as specified and directed. Note :The quoted rates are deemed to be inclusive of sand cushion and plastering to edges is included in quoted rate.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Dismantling timber scantlings any size and section, in any position complete all as specified and directed.

Supply and fixing stainless steel (grade 304) railing made of hollow tubes , channel, plates, etc. including welding , grinding, buffing, polishing, and making curvature (where required) and fitting the same with necessary stainless steel nuts and bolts complete (the railing includes with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc) of required size on the top of the floor/staircase or side of the waist slab with suitable arrangements complete all as specified and directed. Notes: (a) For payment purpose , weight of the stainless steel members shall be considered including fixing accessories such as nut, bots fasteners etc as these are deemed to be included in quoted rate

S&F for Stainless Steel railing (304 grade) with glass , side mounted 900 mm high made of hand rail pipe of 50 mm outer dia and 1.6 mm wall thickness polish with automatic round polishing machine to get a uniform hailine finish K240 mounted with the help of adjustable solid neck support on balustrade of approved design at 900 mm center to center or actual division as per site condition fitted with four numbers for solid glass connectors for holding the infill glass of 12 mm thick toughned and laminated with connectors to be fitted with balustrade with help of SS screw overall mounted on the SS 304 grade solid base plate 100mm x 8 mm with the help of dash fastners or Hilti/Fischers based on sample complete all as specified and directed. Note : The quoted rates are deemed to be inclusive of the railing shall be accessories such as nut, bots fasteners etc and toughned glass

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of modular cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly all as specified and directed by Enrg-in-charge. (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :-

One light point controlled by one switch

One Exhaust fan point controlled by one switch.

One ceiling fan controlled by one switch

One Bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Ser item No 92 above but with 4.0 sq mm FRLSH copper wire with 4.0 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

All as per Ser item 94 but 2runsX4 Sqmm +1runX4Sqmm complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length complete all as specified and directed.

Notes for item No. 92.00 to 95.00 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

Supply and fix of Modular switch 1 way 6A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix of Modular switch 1 way 16A, 1 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable switch of any description complete all as specified and directed.

Supply and fix of Modular Socket 6A/16A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

Supply and fix of Modular Socket, 6A - 2/3 pin combined 2 module 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

S&F Modular angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix of Modular Bell push 6A 1 module, 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable bell push of any description complete all as specified and directed.

S&F electric bell of DINGDONG type, 240 volts, single pole and making all necessary connections, complete all as specified and directed.

Supply and fix in replacement of Modular fan regulator step type in 5 steps, 240V, 50Hz with required modular white cover plate with frame including taking down existing unserviceable socket of any description complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S & F 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 20 watt, 4 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 20 watt, 4 feet long, twin light (cool white & warm white) in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix LED batten 10W (2 Feet) complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix in replacement of Decorative wall light fixture made up of Polycarbonate with and including 7W retrofit LED lamp, full white of approved model including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of sleek round recessed cum surface mounting LED down light 10 W with aluminium die-cast body, finish with drop down PC diffuser warm / full white with optimized heat sink for efficient dissipation including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix LED building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix in replacement of LED bulkhead luminaire 10W in die-cast aluminium alloy/ PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fix in replacement of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

S& F MCCB TPN 100 Amp, 16 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed

S& F MCB SPN 40 Amp, 10 KA, 'C' curve, 230 V, 50 Hz complete all as specified and directed

S& F MCB SP 6 to 32 Amp, 230 V complete all as specified and directed

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or strip and overall PVC sheathed, 25 sq mm 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down existing service cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Supply and fix BLDC ceiling fan, 1200mm sweep, 3 blade, white colour, energy efficient, power cosumption, minimum 310 RPM, 100% copper winding motor with and including down rod, canopy (02 Nos), GI fan clamp with rubber bush, GI nuts, bolts and split pins etc (with remote) and connecting up with 3 core x 0.5 sqmm flexible copper conductor cable from ceiling rose to connector of fan complete all as specified and directed.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

m/s ramesh saran agarwal (BID ID -3220665)

UNIVERSAL ENGG CO (BID ID -3225836)

M/s Jagdish Chandra Arora (BID ID -3225542)

HARNAM SINGH ANIL SINGH (BID ID -3225744)