Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹31.7 LAccepted-AOC 1ST FLOOR PRABHA SHOPPING COMPLEX OLD PAHARGAON DOLLYGUNJ PORT BLAIR SOUTH ANDAMAN ANDAMAN NICOBAR 744103 UDYAM AN 01 0000143 | SOUTH ANDAMANS | ANDAMAN AND NICOBAR ISLANDS | 744103 | L1 | Accepted-AOC L1 | |
| 2 | L2₹34.2 L+₹2.5 L (7.89%)Rejected-AOC SHOP NO 6 BENGALI CLUB MIDDLE POINT SRI VIJAYA PURAM 744101 | SOUTH ANDAMANS | ANDAMAN AND NICOBAR ISLANDS | 744101 | L2 | Rejected-AOC L2 | |
| 3 | L3₹34.8 L+₹3.1 L (9.88%)Rejected-AOC | L3 | Rejected-AOC L3 | |
| 4 | L4₹37.8 L+₹6.2 L (19.4%)Rejected-AOC | L4 | Rejected-AOC L4 | |
| 5 | L5₹38.4 L+₹6.7 L (21.2%)Rejected-AOC NEAR OLD CCS JUNGLIGHAT SRI VIJAYA PURAM 744 103 | SRI VIJAYA PURAM | SOUTH ANDAMANS | ANDAMAN AND NICOBAR ISLANDS | 744103 | L5 | Rejected-AOC L5 |
Tender Value
₹32 L
EMD Value
₹64,000
Closing Date
30 Aug 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GARRISON ENGINEER BRICHGUNJ
GARRISON ENGINEER BRICHGUNJ PORT BLAIR-744 103
PROVN OF COMN STORE AT SIGNAL CENTRE AND ALUMINIUM WINDOW WITH FLY PROOF AT P300 AND CURTAIN RODS AT CERTAIN BLDGS IN INF BN 2 AT BRICHGUNJ MILITARY STATION PORT BLAIR
2022_MES_544815_1
8261A
Open Tender
Civil Works
Item Rate
180 days
GARRISON ENGINEER BRICHGUNJ
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GARRISON ENGINEER BRICHGUNJ PORT BLAIR
₹64,000
Yes
12 Sept 2022
11 Aug 2022
1 Sept 2022
11 Aug 2022
30 Aug 2022
25 Aug 2022
11 Aug 2022 - 25 Aug 2022
Amount
M & L Excavating over areas, n exc 1.5 m deep and getting out Hard/Dense Soil.
All as per serial item No.1.00 here-in-before but for each additional 1.5m or part thereof in depth beyond the first 1.5 m and getting out Hard/Dense Soil.
M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling.
M & L for RCC- M - 30 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and complete all as specified and directed.
M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) above top of footings including attached pilasters and buttresses
M & L for RCC- M -30 Design Mix as in columns, pillars, piers,posts and struts and complete all as specified and directed.
M & L for RCC- M -30 Design Mix as in beams, cantilevers,bressummers, lintels over 1.5m span and complete all as specified and directed.
M & L for RCC- M -30 Design Mix as in slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in,shelves and the likeall and complete all as specified and directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm and complete all as specified and directed.
Removing excvated soil to a distance n.exc 50 m and depositingand complete all as specified and directed.
Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces and complete all as specified and directed.
M & L for Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions and complete all as specified and directed.
Use and waste of form work to sides and sofit of Beams for Fair finished surfaces and complete all as specified and directed.
Use and waste of form work to sides and sofit of Slab & Chajja etc for Fair finished surfaces and complete all as specified and directed.
M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips and complete all as specified and directed.
M&L Mild steel TMT bars 6 mm to 8mm dia cut to length bent to shape required and binding with mild steel wire annealed not less than 0.9 mm dia.
All as per serial item No.16.00 here-in-before but 5mm dia and over up to and including 10mm dia as in stirrups, spacers, binders and the like and complete all as specified and directed.
M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) and complete all as specified and directed.
M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B-O to horizontal or vertical surface including necessary formwork and complete all as specified and directed.
M&L Rendering 10mm thick on concrete surfaces in CM (1:6) finished even & smooth without using extra cement and complete all as specified and directed.
M&L Rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like finished even and smooth without using extra cement and complete all as specified and directed.
M&L 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement. (Note : Water proofing compound shall be measured and paid seperately)
Supply only integral Water Proofing Compound (3% by wt of cement) .
M&L preparation of newly plastered surfaces of wall and applying two coats of Oil Bound distemper over a coat of primer over a coat of internal wall care putty and complete all as specified and directed.
All as per serial item No.24.00 here-in-before but but on Ceiling surfaces.
M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed by Engineer-in-Charge.(Make Apex Ultima)
M&L Filling under floors or in foundations including watering and consolidation
Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil.
M&L Hard Core of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surfce.
M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in 75mm thick as in sub base.
M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in 40mm thick.
M&L PCC 1:3:6 type C1 using 20mm graded aggregate of 75 mm thick as in Plinth Protection.
M & L Chequered cement concrete tiles, with grey cement and pigment 30cm x 30cm x 20mm thick set, jointed and pointed in neat cement slurrry in floors including 20mm thick screed bed in Cm 1:4 complete all as specified and as directed.
M&L Coloured Non-Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor over 15mm thick screed bed in CM (1:6) complete all as specified and as directed.
M&L Glazed Ceramic Coloured tiles 350x 250x 7mm/ 450X 350X 7mm thick as in Dado/Skirting/Steps etc set and jointed in neat cement slury and pointed in coloured cement to match all as specified and directed including backing coat 10mm thick in CM 1:6 complete all as specified and as directed.
Material and labour for anodized aluminium sections (minimum anodisation 15 micros) for partitions, window and door with frame and shutters fully or partially glazed, side Hung type ( two numbers glazed and gauzed) without sash bars, with panel inserts of sheet glass, gauze including necessary jointing cleats, glazing clips, rubber beading, Neoprene packing, anodized aluminium snap beading, screws,i max hinges, butt hinges etc. The size of aluminium sections shall be all as specified in relevant IS code and SSR part-I and completed all as specified and as directed by engineer-in-charge. (Note: (i) supply only panel inserts of glass/gauze, handles, tower bolts and sliding bolt will be measured and paid separately as supply only. (ii) Weight of aluminium section only shall be accounted for payments purpose. However, until rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts of glass/ particle board/gauze, handles, hinges, sliding bolts, tower bolts etc.)
Supply only 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed by Engineer -in-Charge.
Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each panel.
S&F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified and as directed
S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed
S&F Aluminium anodised barrel tower bolt of extruded section of size 100mm long complete all as specified and as directed
S&F 100 mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed
S&F 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed.
S&F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410-W grade E 251 Quality B complete all as specified and as directed
S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240
Mild steel bolts of diameter of neck exc 12mm and n.exc 20mm, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut n exc 30cm long complete all as specified and as directed.
Preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide primer over 10cm in width or girth,not otherwise described.
S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified.
S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws complete all as specified and as directed.
S&F MS works as in wind ties for roof incl securing bolts etc complete all as specified and as directed.
S & F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.
M&L Painting to new steel and iron surfaces of n exc 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and as directed.
Material and labour for false ceiling with aluminium grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces all as specified and directed by Engineer-in-Charge.
Taking down chowkats or frames with shutters area n.exc 1.5 Sqm each(without taking off shutters from the frame) all as specified and as directed
All as per Serial Item No.54.00 here-in-before but are exc 1.5 Sqm but n.exc 4.00 Sqm.
M&L for powder coated aluminium sections in doors/windows/ventilator/cupboards including necessary joining cleats, glazing clips, rubber neoprene packing anodised aluminium snap beading, screws, handles 2 Nos in shutters, hinges, hook and eyes, anodised aluminium fittings etc complete of standard sections all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/Indalco) Note :- Weight of aluminium sections for frames and shutters shall only be considered for measurement for payment. However, cost of other consumables given in the items shall be deemed to be included in the rate quoted. Glass panels, aluminium grill, aluminium wire mesh and prelaminated particle boards as applicable will be measured and paid separately as supplied only.
Supply only 5.5mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares n exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.
Supply only 5.5mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.
Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed by Engineer-in-charge.
Supply and fix 20mm dia aluminium anodised curtain rod , complete all as specified and directed by Engineer-in-Charge.
Supply and fix 20mm dia aluminium anodised brackets, fixed to pelmet box/wall etc complete all as specified and directed by Engineer-in-Charge.
Supply and fix in repairs 20mm dia aluminium anodised curtain rod , complete all as specified and directed by Engineer-in-Charge.
Supply and fix in repairs 20mm dia aluminium anodised brackets, fixed to pelmet box/wall etc complete all as specified and directed by Engineer-in-Charge.
M & L for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit suitable size including Tee junction bends etc concealed in wall/fixed on ceiling and PVC switch board box type complete all as specified and as directed by Engineer-in-Charge. (a) One light point controlled by one way switch
(b) One ceiling fan point controlled by one way switch
(c) One three pin 5 Amp switch socket cum on same board
(d) One three pin 5 amp switch socket outlet multipurpose on independent board
All as per Serial Item No.67.00 here-in-before but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings complete all as specified and as directed by Engineer-in-Charge.
Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed.
Supply and fix switch socket combination 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as dircted by Engineer-in-Charge
Supply and fix switch socket combination 2 in 1, 3 pin 6 and 16 Amp controlled by one switch, flush type.
Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge
Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge
Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed.
Supply and fix energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.
S&F Street light New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 25 w as light and electronic driver complete all as per with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.
M & L in repairs for sub main wiring complete with two runs of 6 Sqmm FRLS single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Casing and caping and all accessories fixed to wall/ roofs/ floors etc with one run of 6 sqmm FRLS single core multistranded copper conductor as earth continuity conductor,complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of conduit & one run of earth continuity conductor shall be measured as one running metre.
Supply, install, commissioning and testing split type air conditioner of nominal capacity 1.5 TR, 5 star INVERTER ANTI POLLUTION (Cooling mode, inverter type, withstand with the option of cool with dual rotor invertor compressor and copper compressor , suitable for working on 230 volts, single phase, 50HZ supply, complete including cutting of wall, providing stand for out door unit and making good disturbed surface of wall etc and remote operation complete all as specified and directed. Note :-Rate are included in quoted by contractor for following items are as under :- (a) Fixing the cooling unit with grouting nuts, cutting groove to wall for gas pipe and water drainage pipe. (b) Insulation of both the copper pipes with insulating material. (c) Charging of correct qty of Ecofriendly refrigerant gas R32 or equivalent after necessary brazing / fixing of both the outdoor/indoor unit and testing complete on load to obtain 18 degree celcious temperature at specified Amps. (d) All other connected civil work such as cutting of holes in existing wall for copper tube and service cable for installation of split AC for proper functioning as directed by Engineer-in- Charge
Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation 170 V to 250 V with output voltage stabilized at 230 V with aacuracy of + 2.5% and of capacity 4 KVA all as specified and as directed. Make : V Guard / Vinitec / AE
Sheet metal enclosure single pole and neutral with a two pin socket and earth plug complete with one MCB single pole and 240V, 20 Amp , 10 kA, complete all as specified.
Supply and fix sheet metal enclosures Loadline distribution board TPN, 4 ways 415 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs and in and including 63 AMP MCCB as incomming complete all as specified and as directed complete.
Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.
M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I
Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 4 Core 16 sq mm.
Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out Soft/loose Soil
Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.
S&F tube light grade galvanised with all fittings laid in trenches of size 50 mm bore.
Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.
Bharat Udyog
AMR TRADERS
bansal construction
SKV Engineering
CHANDER SEKER ENTERPRISE
M/s Ramesh Lal
Bismi Builders & Enterprises
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .