Up-gradation of existing Psychiatric OPD (2nd floor) as a Department of Clinic Psychology at Gauhati Medical College Hospital, Guwahti-32

Amount

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:15.28.1: G.S. Sheet

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :15.12.2: Of area beyond 3 sq. metres

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.15.2.1: Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.12.1.3: 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.12.4.2: 0.63 mm thick with zinc coating not less than 275 gm/m²

Grading roof for water proofing treatment with 22.14.1: Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :21.1.1: For fixed portion 21.1.1.3: Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

21.1.2: For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.3: Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.21.2.2: Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):21.3.2: With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.45.4: Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement :3 coarse sand)

12 mm cement plaster of mix: 13.1.1: 1:4 (1 Cement: 4 fine sand)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Frame size 65 x 125 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 26.88.2: 35mm thick

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).9.1.3: Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :9.74.1: 250x10mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :9.96.1: 300x16 mm

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.3: Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3: Size of Tile 600 x 600 mm

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Centering and shuttering including strutting, propping etc. and removal of form for :5.9.3: Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size de rived from natural sources).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.2.2: Granite of any colour and shade 8.2.2.1: Area of slab upto 0.50 sqm

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :13.43.1: Water thinnable cement primer

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.13.83.2: Two coats

Finishing walls with Acrylic Smooth exterior paint of required shade :13.111.1: Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Applying priming coat:13.50.3 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.61.1: Two or more coats on new work

Finishing of 35mm thick flush Door bothside with 6mm Plyboard Pasting and 1.5mm decorative laminate Pasting,finished with PU poish as per desired colour and shade as per Archietcts instructions and provided with Concealed Door Clouser, Magnetic Door Stopper,125mm long 2.9mm thick Heavy Duty S.S Bearing Hings, Mortice Lock with Handle (All fitings to be of DORMA make as specified in the drawings), complete with all other necessary hardwares as per design,specified and directed by the department/conultant(1x2.1x1.00-2.10M2)

Supplying fitting and fixing Johnson Zebra Roller Blinds(Combi Blackout) make and shade, design as per choice complete as specified and directed by the department at all levels.

Providing erecting cutting and fixing of full height cupboard/wardrobe on place in the position and made with 19mm thick plywood on all frame structure and required partition with self member as per required height with covering door shuters,including providing ,cutting and pasting of 1.5mm thick decorative laminated sheet in the bothside of plywood surface & all hardware fitings like,nails, fevicol, door handle, magnate cather,hinge,lock etc. as a complete with all necessary required materials and labour as directed by the concerned department.

41 /CE PRODUCT AL-60 WORKSTATION:-Table top and 1200 HT Partitions Specification : Partition : AL 60, Height 1200 mm Table top 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Tile Finishers Partitions : Partitions is made of 60mm thick with fabric above and laminate below the table top. Fabric magnetic and laminate board markers are provided for each workstation .Retum and end screen : 525L x 12mm fabric magnetic screens. Support : MS Brackets and gable ends Wire Management: Grommet Hole provided on table top. Raceway provided below table top. MOBILE PEDESTAL 2D+ 1F SIZE: 400Wx 450D X 600 HT Pedestal: Pedestal are made of 18mm thick. PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided finger grooved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite. 1500/1350 L x 600/450 D x 750 Ht

Model: Senate HT -501-A : Size: 2200L X 800Dx 780 H Side Unit: 1010 Wx 500Dx 640 H specification: Material: MDF particle board of 5Omm thickness. Surface finish: Melamine Wire manager meluded. Color: Dark walnut. Make: Featherlite

43/CE Chair :- Model: Optima HB OC-1 High mesh back chair adjustable Lumber SuDDort Seat slide mechanism 3 way adjustable arms Multilocking mechanism Chrome base Make: Featherlite

44/CE Visitor's Chair : Model: Astro VA Medium mesh back chair Additional lumber support Fixed arms Sledge base Make: Featherlite

45/CE Workstation & Reception Chairs Model: Contact Project MB Medium mesh back chair Single lock synchro mechanisim Fixed arms Nylon base Make: Featherlite

46/CE Visitor Module table & Reception Table Model : Edge Table Specification Table top 25mm thick pre laminated board with 2mm edge lipping. Supported on: 50 x 50 ms square powder coated legs. Front Modestry Wire management : race way below table top With gromet hole. MOBILE PEDESTAL 2D+1F SIZE: 400Wx 450Dx 600 HT Pedestal: Pedestal are made of 18mm thick PLB with 2 drawer units and 1 filling folder unit. The Drawer units are made mobile with the use of castors. The drawer units are provided finger grooved handle and suitable locks. CPU TROLLEY AND KEYBOARD TRAY Make: Featherlite.Main table size: 1500x600x750 Ht Side table size: 900x 450x750 Ht with Return Screen

Providing and fixing PVC pipe complete as per field requirement. PVC pipe 110mm

Providing and fixing PVC Coupler complete as per field requirement. PVC Coupler 110mm

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :17.3.1: W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :17.10.1: Kitchen sink with drain board 17.10.1.3: 510x1040 mm bowl depth 200 mm

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.18.50.1: 15 mm nominal bore

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.17.73.2: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :17.11.2: Size 600x450x200 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Oval shape 450x350 mm (outer dimensions)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 18.9.1: 15 mm nominal outer dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1.14.1: 12X 1.5 sq. mm+ 1X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2X4 sq. mm + X4 sq. mm earth wire

4X6 sq. mm + X4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following nodular switclh sockct on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1.24.1: 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular Each plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1.27.1: 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

6 Module (200mmX75mm)

12 Module (200mm X 150mm)

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in surface etc as required. 1-2 Module (75mmX75mm)

3 Module (100mmX75mm)

8 Module (125mnX125mm)

12 Module (200mmX150mm)

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying with fitting fixing of surface & wall mounted LED luminaries complete with all accessories including driver directly on wall ceiling including connection with I.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (BAJAJ/Crompton/PHILIPS/Havells or equivalent considering the mother items rate and specification) (a) I8W 4ft LED Batten

Supplying and commissioning of the following indoor recessed Type Luminairs complete with all accessories including driver in the false ceiling (Armstrong / Gypsum or similar type) mounted with necessary support and connection with 1.5sqmm PVC insulated SC copper conductor as required and as directed by the deptt. (300mm X 300mm) (Crompton or equivalent make) 30W, recessed Type (300mm X 300mm) LED fitting

Supplying and commissioning of the following indoor recessed Type Round Luminairs complete with all accessories including driver in the false ceiling (Armstrong / Gypsum or similar type) mounted with necessary support and connection with 1.5sqmm PVC insulated SC copper conductor as required and as directed by the dept. (Bajaj or equivalent make) 15W, recessed round Type LED fitting

Supplying and commissioning of the following indoor recessed Type Square Luminairs complete with all accessories including driver in the false ceiling (Armstrong / Gypsum or similar type) mounted with necessary support and connection with 1.5sqmm PVC insulated SC |copper conductor as required and as directed by the dept. (Bajaj or equivalent make) 18W, recessed Square Type LED fitting

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning elc. as required. Single pole

Double pole

Supplying fitting fixing of following 4P 240-440V 'C Series 10ka MCB in the existing DB/panel as specified and directed by the department. (Legrand or equivelent make) 63A 4P 240-440V'C Series 10ka MCB

Supplying including fitting fixing of following |A.C. Ceiling fan (1SI Marked) complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. (USHA or Equivelent make) 1200mm Sweep

Supplying including fitting fixing of following A.C. Ceiling fan (ISI Marked) complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Dept.)as required complete and as directed by the Department [Without regulator). (Crompton or Equivelent make) 900mm Sweep

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (USHA or equivelent make) 225mm Sweep Metal Blade

Supplying including fitting fixing of following A.C. Wall fan in the wall of following sweeps with making necessary connection as approved by the Dept.)as required complete and as directed by the Department. (USHA or Equivelent make) 400mm Sweep

Supplying fitting fixing of following 25A Motor Starter (AC Starter) in the existing 2 Module Box as specified and directed by the depart1ment. (Havells or equivelent make)

Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthing system with 100 MM dia. 2.9 Metres length corrossion free centrifugally Cast Iron Earthing Electrode complete with Reslow/BFC Grounding chemical compound ( 40 KG) and Advance Earth Pit cover (CI) of size 300 mmx300 mm including excavation of earth pit and construction brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the dept. 100 mm Dia Chemical Earthing

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Supplying testing and commissioning of Hi -- wall INVERTER 3 STAR rating non ducted copper condencing unit split type air conditioner of the following capacity with cordless remote complete with copper pipe and electrical connection cable, as approved by the Dept.)up to 3 m between the room unit and out door unit as directed by the department.a) 1.5 Ton 3 Star (Voltas or Equivelent make)

Providing Copper pipe including control cable fitting for Split / Cassetter AC as per required size inclduing Nitrile Insulation complete For 1 Tr to 1.5 Tr Capacit

Supplying with fitting and fixing of ready made powder coated MS frame for installation of Outdoor Unit of Airconditioner machine for 1.0 Tr to 2.0 Tr Outdoor Unit

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type single door, wall mounting compartmentalize panel board of size 0.9M(B)X1.5M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 40mm X 40mm X Smm size angle having 4 nos legs at the bottom and C.R. sheet roofing on the top. The panel board is to be fitted |direct on wall with necessary nut-bolt etc. complete neatly wiring done with a provision of 125A MCCB as Incomer and Snos TPN as out going as specified and directed by the dept. confirming to IP 65 protection comprising of the following electrical items:1. i) 40mm X 6mm 4 strip Aluminium Bus Bar 1.5 M length each 2. Poilt Lamp with integral ckt LED T10- 230 V (Red, Yellow.& Blue) 3 nos 3. Multifunction Meter -1 no 4. 2 A SIide fuse unit - 3 nos (Incoming Switch Gear of reqd. rating will be measured and paid separately)

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. required 100 Amp. 3OKA, FPMCCB

250 Amp. 36KA, FPMCCB

Supply of following size PVC/XLPE insulated and PVC sheathed 1.1KV gd Solid Aluminum conductor up to 10 sqmm, balance stranded conductor, XLPE Insulated, cores laid up, PVC tape innersheathed, Armour (Aluminium wire for single core up to 70 sqmm, balance Aluminium strip, Glavanised wire for cables upto 2x10 sqmm,, 3x10 sqmm,,4x6 sqmm, & balance al galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable as specified and directed by the dept. ( Havells or equivelent make) 16.0 Sqmm 4core

70.0 Sqmm 4core

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with lmm thick saddle)

Above 35 sq. mm and upto 95 sq. mm

Supplying fitting fixing of following 4 way 240 440V wall mounted Bus-Bar Chamber as specified and directed by the department. (Havells or equivelent make) 63A 4way 240-440V Bus-Bar Chamber

100A 4way 240-440V Bus-Bar Chamber

FAKRUL ISLAM KHANDAKAR

Beena Infratech