IMPROVEMENT OF WATER SUPPLY SYSTEM AT PALLIPALAYAM MUNICIPALITY,NAMAKKAL DISTRICT UNDER AMRUT-2.0

Amount

Supply,delivery of DI K7 S/S tyton joint pipes of 5.0m length for potable water supply as per IS specification no. 8329 /2000 and as amended from time to time with ISI marking of the following sizes and for delivery at site including loading, unloading, freight stacking, conveyance to the work site etc., complete as directed by the Engineer-incharge

Supply, delivery of Ductile Iron Specials As Per IS 9523/2000 including unloading, transportation and stacking charges, conveyance to work site etc., complete as directed by the Engineer in charge.

DI D/S Specials (250 mm to 300 mm)

Supplying and conveying to site, the following sizes of HDPE pipes of class PN6 (PE-100) confirming to IS:4984/1995, as specified in Technical specifications in standard lengths including labour charges for loading, unloading and stacking at site and transportation charges etc., complete as per standard specifications and as directed by the Engineer in Charge.

Supply, delivery of HDPE Specials As Per IS 1736-1995 including unloading, transportation and stacking charges.Specials for HDPE pipes as per IS 8360/1977/ Part I(Reaffirmed 1992) Part II and III (Reaffirmed 2002). Reaffirmed to IS 4984-2016 conveyance to work site etc., complete as directed by the Engineer in charge.

HDPE Bends -90°

HDPE Equal Tee

110 mm X 110 mm X 110 mm

140 mm X 140 mm X 140 mm

200 mm X 200 mm X 200 mm

HDPE Reducer

140 mm X 110 mm HDPE Reducer

160 mm X 110 mm HDPE Reducer

160 mm X 140 mm HDPE Reducer

200 mm X 110 mm HDPE Reducer

200 mm X 140 mm HDPE Reducer

110 mm HDPE EndCap

FLOW CONTROL VALVE: Supply, Installation of DI Flow rate Limit control Valve (PN10/16) with the function to limit the flow rate to a set point. In case the downstream demand increases beyond the set limit, the valve closes down to bring the flow back to set limit. The valve shall have an orifice plate and the orifice diameter is designed based on the set point as per the requirement and installed downstream of the control valve. “Manufacture supply and delivery of DI D/F Diaphragm type own medium controlled Flow rate Limit Control valve with cast body of ductile iron grade G-40 or equivalent grade or as per IS 3896-Part-2-1985 customized control cylinder for linear control behaviour or equivalent, performed diaphragm and pull out safe profile sealing ring of EPDM, threaded inserts (CORFIX - to prevent the coating from coming off in the connections area as well as corrosion and incrustations in the control circuit) or equivalent.

Flange connection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/IS 1538, all parts (Epoxy coating, and diaphragm) in contact with medium are as per KTW and DVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating (EP-P) should be approved by W270. (EP-P)/ WRAS & NSF.”Pilot valve system having Stainless Steel / Brass fittings with spring of stainless steel 304 as per standard parts according to DIN EN 12 266-1, orifice plate shall be as per the set point of flow rate and all the external control tubing of SS 304 / Copper/ reinforced plastic rated PN16, Tightness to DIN EN 12 266-1, leakage rate A (or) equivalent and the needle valve/ speed control device should be provided to vary opening speed of the main diaphragm with self-cleaning filter to avoid possibility of dirt build up inside the control tubing.

DI D/F Gate Valve: Supply,Delivery and fixing of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron of Grade GGG 40 or equivalent grade, Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 O- Ring protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 14846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application with pressure rating PN 10/16 and with 5 years

Battery Powered Electromagnetic Flowmeter: Operating Pressure : max 10 bar g bar g, Operating Temperature : Max 80 deg C deg C. Electromagnetic Flow Sensor - Type : Pulsed DC, Meter size : Ref BOM, Flow tube : Metallic Alloy, Coil housing : Sheet Steel, Liner : Rilsan, Electrodes : SS316, Grounding type : Rings Grounding ring material : SS316, Process connection : Flanged to DIN PN16, Flanges : CS Flange, Area classification : Non-Hazardous, Cable entry : M20 x 1.5 with blind plug, Protection class : IP 68, Calibration : 3 point Type : Wet. Signal Converter; Cable length : 5 METER , Mounting : Wall Mounting/ Panel Mount, Type : Microprocessor Based, Accuracy : Better than ± 0.5% of measured value, Max load : 500 Ohms, Display : Large back lit LCD Display, Housing : Polycarbonate Housing, Battery : Dual Battery Pack, Cable entry : M20 x 1.5, Area classification : Non-Hazardous, Protection class : IP 66 / 67. Accessories : GSM Modem with Data logging facility and adaptor.

Supply, delivery of Ductile Iron Specials as Per IS 9523/2000 including unloading, transportation and stacking charges for fixing of valves with specials including labour charges for lowering, laying, jointing etc complete as directed by Engineer in Charge

For 110 mm Main valves arrangements comprising 100 mm Flow Control Valve, 100 mm DI D/F Gate Valve and 100 mm Electromagnetic Flow Meter upto 35 lps flow with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below

100 mm Dia DI Flanged Socket Tail Piece - 2 Nos

100mm Dia DI D/F Pipe - 0.5 m length - 2 Nos

100 m Dia DI D/F Gate Valve - 1 No

100 mm Dia Flow Control Valve 1 No

100 mm Electromagnetic Flow Meter - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

100 mm Dia DI pipes and Specials - 1 m

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

100 mm Dia DI Pipes and Specials - 2 Nos.

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

100 mm dia DI pipes and specials - 6 Nos.

Above 110 mm upto 160 mm Main valves arrangements comprising 100 mm Flow Control Valve, 150 mm DI D/F Gate Valve and 100 mm Electromagnetic Flow Meter upto 35 lps flow with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below

150 mm Dia DI Flanged Socket Tail Piece - 2 Nos

150mm Dia DI D/F Pipe - 0.5 m length - 2 Nos

150 m Dia DI D/F Gate Valve - 1 No

150 mm X 100 mm Dia DI D/F Taper - 2Nos

100 mm Dia Flow Control Valve 1 No

100 mm Electromagnetic Flow Meter - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

150 mm Dia DI pipes and Specials - 1 m

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

150 mm Dia DI Pipes and Specials - 2 Nos.

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

150 mm dia DI pipes and specials - 5 Nos.

100 mm dia DI pipes and specials - 3 Nos.

Above 160 mm upto 200 mm Main valves arrangements comprising 100 mm Flow Control Valve, 200 mm DI D/F Gate Valve and 100 mm Electromagnetic Flow Meter upto 35 lps flow with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below

200 mm Dia DI Flanged Socket Tail Piece - 2 Nos

200mm Dia DI D/F Pipe - 0.5 m length - 2 Nos

200 m Dia DI D/F Gate Valve - 1 No

200 mm X 100 mm Dia DI D/F Taper - 2Nos

100 mm Dia Flow Control Valve 1 No

100 mm Electromagnetic Flow Meter - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

200 mm Dia DI pipes and Specials - 1 m

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

200 mm Dia DI Pipes and Specials - 2 Nos.

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

200 mm dia DI pipes and specials - 5 Nos.

100 mm dia DI pipes and specials - 3 Nos.

Above 200 mm upto 300 mm Main valves arrangements comprising 100 mm Flow Control Valve, 250 mm DI D/F Gate Valve and 100 mm Electromagnetic Flow Meter upto 35 lps flow with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below

250 mm Dia DI Flanged Socket Tail Piece - 2 Nos

250mm Dia DI D/F Pipe - 0.5 m length - 2 Nos

250 m Dia DI D/F Gate Valve - 1 No

250 mm X 150 mm Dia DI D/F Taper - 2Nos

150 mm X 100 mm Dia DI D/F Taper - 2Nos

100 mm Dia Flow Control Valve 1 No

100 mm Electromagnetic Flow Meter - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

250 mm Dia DI pipes and Specials - 1 m.

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

250 mm Dia DI Pipes and Specials - 2 Nos.

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

250 mm dia DI pipes and specials - 5 Nos.

150 mm dia DI pipes and specials - 2 Nos.

100 mm dia DI pipes and specials - 3 Nos.

Pressure Relief Valves: Supply and delivery of DI D/F Pressure Sustaining / Relief Valve (PN10/16) with the function to relieve excess pressure in the downstream pressure to set point irrespective of upstream fluctuations. The downstream pressure set point can be changed as per the requirement. “Manufacture supply and delivery of DI D/F Diaphragm type own medium controlled Pressure Sustaining / Relief valve with cast body of ductile iron grade GGG-40 or equivalent grade or as per IS 3896-Part-2-1985 customized control cylinder for linear control behaviour or equivalent, performed diaphragm and pull out safe profile sealing ring of EPDM, threaded inserts (CORFIX - to prevent the coating from coming off in the connections area as well as corrosion and incrustations in the control circuit) or equivalent. 2 pressure gauges for operator-friendly control to determine the actual inlet and outlet pressure connected directly to the valve. Flange connection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538,

all parts (Epoxy coating, and diaphragm) in contact with medium are as per KTW and DVGW certified (harmless)/ WRAS & NSF approved. The EPDM rubber & Epoxy coating (EP-P) should be approved by W270.(EP-P)/ WRAS & NSF.” Pilot valve system having Stainless Steel / Brass fittings with spring of stainless steel 304 as per standard parts according to DIN EN 12 266-1 with all the external control tubing of SS 304/ Copper/ reinforced plastic rated PN16, Tightness to DIN EN 12 266-1, leakage rate A (or) equivalent and the needle valve/ speed control device should be provided to vary opening speed of the main diaphragm with self-cleaning filter to avoid possibility of dirt build up inside the control tubing.

DI D/F Gate Valve: Supply,Delivery and fixing of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron of Grade GGG 40 or equivalent grade, Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 O- Ring protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 14846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application with pressure rating PN 10/16 and with 5 years

Supply, delivery of Ductile Iron Specials as Per IS 9523/2000 including unloading, transportation and stacking charges for fixing of valves with specials including labour charges for lowering, laying, jointing etc complete as directed by Engineer in Charge

For 110 mm Main valves arrangements comprising 100 mm DI D/F Gate Valve and 100 mm Pressure Relief Valve with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below

100 mm Dia DI Flanged Socket Tail Piece - 2 Nos

100 mm Dia DI D/F Pipe - 1 m length - 2 Nos

100 m Dia DI D/F Gate Valve - 1 No

100 mm Pressure Relief Valve - 1 No

100 mm DI D/F D'Foot bend - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

100 mm Dia DI pipes and Specials - 2 m

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

100 mm Dia DI Pipes and Specials - 2 Nos.

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

100 mm dia DI pipes and specials - 7 Nos.

DI D/F Gate Valve: Supply,Delivery and fixing of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron of Grade GGG 40 or equivalent grade, Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 O- Ring protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 14846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application with pressure rating PN 10/16 and with 5 years

Supply, delivery of Ductile Iron Specials as Per IS 9523/2000 including unloading, transportation and stacking charges for fixing of valves with specials including labour charges for lowering, laying, jointing etc complete as directed by Engineer in Charge

100 mm DI D/F Gate Valve PN 16 in 100mm DI main with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below - Data:-27

100 mm DI D/F Gate Valve - 1 No

100 mm DI.Flgd Spt T.P.-1 No

100 mm DI.Flgd Skt T.P.-1No

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

100 mm dia DI pipes and specials - 3 Nos.

Jointing the C.I/ D.I-S/S pipes and specials with rubber gaskets (tyton joints) including cost of lubricants. (including cost of jointing materials)

100 mm Dia DI pipes and Specials - 2 Nos.

80 mm DI D/F Gate valve for Scour in 110 mm HDPE main with fixing of DI Specials as per IS 9523/2000 including loading, transportation and Stacking Charges as per the following sizes as per the drawing, details of valves and specials as below - Data:-26

100 x 100 x 80 mm Branch Flanged Scour Tee - 1 No.

80 mm x 1.00 m DI D/F Pipe - 2 Nos

80 mm DI D/F Gate Valve - 1 No

80 mm DI D/F D'Foot bend - 1 No

80 mm DI D/F 90° bend - 1 No

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the Officers.

80 mm Dia DI pipes and Specials - 2 m

Jointing the C.I/ D.I Double flanged pipes and specials with rubber insertion to the required specifications with M.S. bolts and nuts, complete. (including cost of jointing materials)

80 mm Dia DI pipes and Specials - 8 Nos.

Supply and Delivery of MS pipes of preferred dimensions ranging from 168.30mm OD to 2540mm OD having 2.6mm to 25mm thickness as per Table- 5 of IS 3589/2001 fabricated with Fe410 grade steel conforming to IS 3589:2001 and other allied codes with externally coated with plant applied CM 1:3, minimum 20mm thick including reinforcement as per clause A-9 of Annex-A of IS 3589:2001 for trenchless cutting works in SH/NHAI Roads including transportation, unloading and stacking charges

For 110 mm HDPE pipe in 219.10 mm x 3.6 mm thick MS Pipe

For 140mm HDPE pipe in 273 mm x 5 mm thick MS Pipe

For 200 mm HDPE pipe in 406.40 mm X5 mm thick MS Pipe

For 250mm DI D/F pipe in 508 mm x 5.6mm thick MS Pipe

Earth work excavation and depositing on bank with an initial lead of 10m and initial lift of 2m inthe following classification including otherincidental charges such as barricading etcexcluding refilling in hard stiff clay,stiff blackcotton,hard red earth, shales, murram, gravel, stoneyearth and earth mixed with small size bouldersand hard gravelly soil Exculding BT & CC Road Cutting charges etc., complete as directed by the Engineer in Charges

HDPE Pipes

DI Pipes

Refilling with excavated soil (other than sand) complying with standard specification in layers of 15cm watered well rammed and consolidated after the pipes and specials are laid,jointed and tested etc. and removing and depositing the surplus earth complete as directed by the Engineer--in-charge.

HDPE Pipes

DI Pipes

Lowering HDPE pipes and specials to trench and laying to proper grade and alignment complete as per standard specifications and as directed by the Engineer in Charge

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment complete as per standard specifications and as directed by the Engineer in Charge.

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc., complete as per directed by Engineer in Charge.

Jointing the DI S/S pipes and specials with rubber gaskets (tyton joint) including cost of lubricants, cost of jointing materials and testing to the required pressure with water etc., complete as per standard specifications and as directed by the Engineer in Charge.

Testing of M.S. / C.I. / D.I / P.V.C. / H.D.P.E / pipes with hydraulic testing equipment by filling with waterand testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc., complete for the following diametres of pipes.

HDPE Pipes

DI Pipes

Valve Chamber :Construction of masonry valve chamber:

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum

Plain Cement Concrete 1:4:8 using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Brick work in CM 1:5(one cement & five sand) using ground moulded country bricks of size 8.75 inch X 4.25 inch X 2 3/4 inch standard specification including finishing, curing, etc., complete complying with standard specification - 100cft

Plastering with cement mortar (1:3) 12 mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309)

RCC (M20) Precast Slab of 0.15m thickness using 20mm thick hard broken stone jelly and river sand excluding the cost of reinforcement grills and fabrication charges but including moulding, curing, finishing charges and fixing in position neatly complying with standard specification and as directed by the Departmental Engineer etc. complete-

Supply and Fixing of Cut Stone Slab all faces dressed including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

CI surface box at a of size 100x125x150 mm conforming to IS 3950 having hinged and weighting not less than 14 kg.The surface box shall be fixed on top of the RCC cover slab during the casting of slab for key rod operation. The surface box shall be painted with 3 coats of black bitumastic paint

Refilling the trenches with suitable excavated earth available in layers of 150 mm thick, watering, ramming & consolidation complete as directed by the Engineer in charge

Conveyance of excess earth to a distance not exceeding 5km as directed by the Corporation Engineer including cost of loading, transportation and unloading charges etc complete (Total Earthwork Quantity - Refilling Quantity)

Scour Valve and Sluice Valve

Scour Valve Chamber - 1 m x 1.3 m x 1.5 m - Up to 200 mm main

Sluice Valve Chamber - 1.2 m x 1 m x 1.2 m - Up to 110 mm main

Flow Control Valve (FCV +Flowmeter + Sluice Valve)

1.2 m x 0.9 m x 1.1 m - Up to 110 mm main

2 m x 1.2 m x 1.2 m - Up to 160 mm main

2.9 m x 1.3 m x 1.5 m - Up to 300 mm main

Pressure Relief Valve (PRV + Sluice Valve)

1.2 m x 1 m x 1.2 m - Up to 110 mm main

Disposal of surplus earth including loading & unloading, conveyance within a distance of 5 Km and spreading as directed by the Engineer in Charge. For Pipe Quantity and Road Restoration

Labour charges for cutting open roads in BT / WBM for laying of water supply pipe line measurement

Dismantling concrete roads for laying pipe line excluding cost of earth work in linear measurement

Trenchless cutting works in SH / NHAI road crossings as directed by Engineer in Charges. Excavating of driving pit and receiving pit of size 3.00m (length) x 3.50m (breadth), upto 5m depth in all soil including shoring and strutting using 6mm tk MS Plate of size 3.50m x 3.50m usable for 20 operations and providing 16mm thickness MS plate of size 3.00m x 3.50m with 100mm x100mm x 12mm angles of 4m length for holding the MS plates for Thrust arrangements to receive the impacts during pushing operation of encasing pipe. Lowering the following size of MS encasing pipe by using Contractor’s crane and machineries and jointing MS pipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc and driving the horizontal bore by pushing / jacking method (trenchless technology method) using contractor’s machineries such as cranes, jacks, jacking materials, generator, welding machineries, compressor, jack hammer and other equipments etc. without interfering and causing any hindrance to the movement of traffic or any other vehicles, without any disturbances to the railway/road/canal formation etc. including bailing /

pumping of water where ever necessary without affecting any installation like water supply pipeline/telephone cable, electric cables etc. passing nearby area and scooping the earth inside the pipes and pit and depositing the surplus earth in a convenient place and leveling the site after completion of entire work as directed by TWAD Engineers. The rate includes the cost of driving pit, thrust bed/wall and receiving pit to the depth of om to 5m excluding the cost of MS pipes.

For For 110 mm HDPE pipe in 219.10 mm x 3.6 mm thick MS Pipe

For For 140mm HDPE pipe in 273 mm x 5 mm thick MS Pipe

For For 200 mm HDPE pipe in 406.40 mm X5 mm thick MS Pipe

For For 250mm DI D/F pipe in 508 mm x 5.6mm thick MS Pipe

BARRICADING FOR PIPELINE WORKS FOR THE WSS WORK: Barricading work (Where, there is less traffic areas and broader roads etc.) for laying of pipe line using casurina poles at 1.50m center to center (8cm to 10cm dia and 1.80m height) vertical with horizontal poles in three rows including painting the vertical poles in the road facing sides with ready mix paint, tying the vertical and horizontal poles with coir rope including fixing charges and fixing 75mm dia reflectors including earth work excavation for fixing vertical posts and finally removing and stacking the materials safely for further use etc., complete and as directed by the engineer in charge.

Length of barricading (Less Traffic)

BARRICADING FOR PIPELINE WORKS FOR THE WSS WORK: Barricading work (Where the lines are in narrow width of municipality area, busy streets like Market, Bus-stand and in the Highways etc.) for laying of pipe line using casurina poles at 1.50m center to center (8cm to 10cm dia. and 1.80m height) vertical with horizontal poles in two rows, painting the vertical poles in the road facing sides with ready mix paint, tying the vertical and horizontal poles with coir rope including supplying, delivery and fixing of GI sheet (0.90m x 0.8mm thick) in the horizontal poles and fixing 75mm dia. reflectors including earth work excavation for fixing vertical posts and finally removing and stacking the materials safely for further use etc., complete and as directed by Departmental officers.

Length of barricading (Heavy Traffic)

Instrumentation

Design, supply, installation of level gauge at each SR over head tank. Application: Flout & Board level indicator switch for max 100 degree celsius Temperature. Instrument: Float and Board level indicator for water application forms connection. 1" ASA flange 150# RF, SS304 Float : SS 316, 250mm 80mm wire range, SS 304, Thickness 4mm, Nylon material printer: Red p[pointer with Nylon roller pulley enclosure: SS304, Power Coater 2 Nos Scale / Board : Aluminium Scale with marking in Block & White least count : 10mm Mounting Bracket : Type (Powder Coated) Nozzle: At actual Connecting Pipe: as per nozzle distance Float test pressure : 6 kg/ Cm2 Total Length - 5000 mm

HSC for HDPE Mains

1.Labour for cutting open road for laying water mains or sewer.B.T. Roads (or) Maccadam road.

2.Earth work excavation and depositing on bank with initial lead of 10 m and lift of 2 M in narrow trenches for laying of pipes for water supply and sewerage works in the following type of soils Hard stiff clay, stiff black cotton, hard red earth, shales, murram gravel, stoney earth and earth mixed with small size boulders and hard gravelly soil. as directed by Departmental officers

3.Refilling with excavated soil (other than sand) complying with the standard specification for filling in foundation and basement (total earth work quantity - volume of the pipe)

4.HSC Connection in HDPE Mains for Water Supply Scheme Supply, delivery of the following Electrofusion tapping saddle PE 80 blue, PN 12.5 with female threaded metal insert of SS 304 as per standards BS EN 12201 tested as per BS 6920 for drinking water in WRCNSF ltd, UK. (Non Wrap with top loading type). Sizes:63mm to 315mm dia distribution HDPE pipes. shall as detailed in a drawing furnished.

5.Supply, delivery of Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded as per IS :554 BSPT, ISO:7-1 to suit the corresponding bore sizes of 15mm dia size ( 1/2", ) in the saddle Connection .as per IS :554 BSPT, ISO:7-1

6.Supply, delivery of Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, OD MDPE pipes

7.Supply, delivery of Poly propylene 90 Degree Compression elbow with compression joint at both ends as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mmOD MDPE pipes

8.Supply, delivery Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 as per standards ISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK for connecting 20mm, 20mm and 25mm outlet points of Brass ferrule of sizes 15mm respectively.

9.Supply, delivery of MDPE PE 80 Blue pipe as per standards ISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK

10.U PVC ball valve with one side compression end and other side female end as per ISO 4422-4 and Tested as per BS 6920 in WRC-NSF LTD, UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and 32mm OD X 3/4" ID

11.Supply and delivery of protection box of size 20cm x 30cm for fixing of Water Meter. The box should be rectangular base in construction and material of construction should be weather resistant polyethylene (PE) blue /black .Reinforcement rips should be provided at the walls of the box. Box should be at two components comprising body and lid. Lid should be press fitted to the body. No hinges should be used for opened /closed. Operation meter box should be provided with built in lock. The body as inlet and outlet windows to pass the pipe through suitable for use with pipes of sizes up to 1" .Base of the box should be designed in such a way .That the box can be installed to the floor/wall using anchor Bolts / screws without grouting the entire base of the meter Box .Provision for fixing Name plate showing the name of the Department etc., complete and as directed by the Engineer in Charge.

12.Supply and delivery of Multi Jet water meter with removal mechanism water meters confirming to ISO 4064 Class B or IS 779 Standards with type test certificates for Routine Test, IP 68 Test certificates issued by FCRI/NABL Accredited Lab. The water meter shall have magnetic or mechanical drivers or shall be versatile for installation in Horizontal position. The meters shall be hydrodynamically or hydrostatically balanced. The runner, runner chamber, pointers of the meter shall be as per ISO 4064 Class B specification. Dry dial excavated counter housing fully protected against flooding ensuring easy reading in all climatic conditions. The meters shall be inferential, Dry-Dial Type, Class B with straight reading Cyclometer with inbuilt filter basket, Meter body shall be of Brass body confirming to DCB2 material specifications and suitable for drinking water applications. The body shall be painted, or powder coated. Each water meter shall be supplied with Brass Nut and tailpieces, protective top lid, secured by a robust hinge with sealing facilities for couplings. The process connections shall be screwed ends with BSP Threads. Each water meter shall be tested for a maximum pressure rating up to 16 Bar. Water meter shall be supplied with manufacturer Calibration & hydrotest certificate. The dimensions must comply to IS 779 standards

13.Lowering MDPE pipes and specials to the trench and laying to proper grade and alignment, jointing with couplers with cement past etc coplete for the pipes size upto 40mm dia OD MDPE Pipes

14.Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc., complete as per directed by Engineer in Charge.

15.Supply, delivery and fixing of GI pipes for encasing in open drain including handling charges. etc complete as per standard specifications and as directed by the Engineer in Charge.

16.Labour charges for drilling, cutting, Threading and Fixing Ferrules in distribution pipes.

P.C.C 1:4:8 (one cement, four sand and Eight coarse aggregate) using Ordinary Portland cement and 40 mm H.B.G stone including mixing concrete, laying, curing and compacting of concrete etc., complete and as directed by the Engineer in Charge.

P.C.C 1:2:4 (one cement, two sand and four coarse aggregate) using Ordinary Portland cement and 20 mm H.B.G stone including mixing concrete, laying, curing and compacting of concrete etc., complete and as directed by the Engineer in Charge.

GST Amount for providing Service to Government Contract Works for the Above construction works. (GST Amount is the Total GST Amount for total overall quoted amount above this row for this work)