SPECIAL REPAIR TO BLDG NO P-748 AT TRANSIT CAMP AT BD BARI UNDER GE KALUCHAK

Amount

B&R PORTION:- Demolition of cement concrete (unreinforced) in ground floors and paving n exc. 15 cm. thickness, below or above ground level complete all as specified & directed.

Demolition of cement concrete (reinforced ) in ground floor and paving n.exc 15cm thickness (below or above ground level) (reinforement cut as required to facilitate demolition), complete all as directed by Engineer-in-Charge..

Taking down cement plaster and decayed concrete of any description from roof projection, chajja etc, racking out jointing hacking for key scrubbing down with water and removing all the demolished material outside cantt area complete all as specified and directed.

Taking down cement plaster and decayed concrete of any description from roof projection, repair with 15mm thick rendering on fair face of concrete surfaces in CM 1:4 with water proofing compound ( As per manufacturer detail ) including junction portion, making proper slope towards out side, finished even and smooth with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) and provision of two coats of cement based paint and including all necessary scaffolding / safety arrangement for carrying out work on outer side of triple Storey Building complete all as specified and directed. (Note: Water proofing admixture shall be measured and paid seprately)

Dismanting floor, hearth wall tiling or terrazzo toping on wall including cement mortar bedding (but not backing) & rubbish off the premises complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt) & removing from site, complete all as specified.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area exceeding 1.5Sqm but not exceeding 4Sqm each including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt) & removing from site, complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Complete removal of the existing sunken treatment including roughing and prepration surfaces of old concrete floor by picking , scurubbing down with steel brushes ,sweeping clean and washing down with water to remove dust etc.and applying the following treatment complete all as specified (a) 15 thick rendering plaster on fair faces of brick work or cement surfaces in cm 1:4 mixed with water proofing admixture by weight of cement to sunken portion including wall of sunken portion with proper slope towards outside and finishing cement concrete or brick work surface even and smooth using extra cement finishing concrete including walls of sunken portion with proper slope all as spd ( NOTE :- W P admixture shall be measured and paid separately) (b)Applying Ist course of bitumenous primer @ 0.4 ltr /sqm conforming to IS-3384 over plastered surface. (c)Applying 2nd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperatureand applied @ 1.2 kg/sqm. Item contd to 9.01

(d)Applying 3rd course of APP (Atactic Polypropylene) modified polymeric 3mm thick weight not less than 3.6 kg/sqm with 160 Grams/sqm non woven polyster made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat . (e)Applying 4th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature and applied @ 1.2 kg/sqm .

Complete removal of existing roof treatment of any description viz. tarfelt or membrane surface or roof tiles etc. including grubbing up of tree roots and removing all the debris to a distance n.exc 100m and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt / dust etc and applying the following roof treatment complete all as directed:- (a) Applying Ist course of 15 mm thick cement screed in CM 1:4 over concrete surface. (b) Applying 2nd course of bituminious primer confirming to IS-3384 @ 0.4 lit/sqm over the screed bed. (c) Applying 3rd course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C and applied @ 1.2 kg/sqm. Item Contd 10.01

(d) Applying 4th course of APP (Atactic polypropylene) based polymeric membrane minimum weighing 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 100 mm overlap by forced / torch application as per manufactures instructions. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 degree C and applied @ 1.2 kg/sqm over APP membrane, complete all as specified and directed.

Plain Cement Concrete 1:5:10 (using 40mm graded crushed stone aggregate) as in mass filling in sunken floor of toilets, complete all as specified.

Steel water tubing of 50 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls, ceilings, laid in floors or from sunken floor to out building wall, complete all as specified.

Vitreous china squatting pan 'Orissa pattern, size 580x440 mm white, with integral foot rest and P or S trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding and making good to floor as existing, fixed in repairs, complete all specified in SSR part I complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed, complete all as specified.

Taking up or down 15 mm bore steel tubing and connections including cleaning, threading for refixing or removal to store, all as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning, threading for refixing or removal to store,complete all as specified & directed.

15 mm bore steel tubing, medium grade, galvanished with all fittings like socket, union, elbow, bend, tees etc and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

20 mm bore steel tubing, medium grade, galvanished with all fittings like socket, union, elbow, bend, tees etc and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Fixing only old steel galvanised tubing of 15 mm bore, with and including all fittings in new or old position as in walls, ceiling, floors etc complete all as specified.

Fixing only old steel galvanized tubing of 20mm bore, with and including all fittings in new or old position as in walls, ceiling, floors etc,complete all as specified & directed.

Dismantling water tanks of any description exc 500 and not exe 1000 litre capacity and removing from site complete all as specified & directed.

Rotational moulded polyethylene water storage tanks, tripple layered (cylindrical vertical with closed top ) hoisted and fixed in position, including over flow and drain out pipe complete of 1000 litre capacity , all as specified in SSR Part-I complete all as specified & directed.

Ball brass valve, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete of 20 mm bore dia complete all as specified & directed.

15 mm bore brass stop cock, cast copper alloy CP with long shank and cup (concealed type), high pressure, with capstan head handle, weight not less than 450 gms screwed both ends for iron pipe or for unions fixed in repairs, complete all as specified and directed.

15 mm bore Angle valves, cast copper alloy CP, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions fixed in repairs, complete all as specified and directed.

15 mm bore bib taps, cast copper alloy CP with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed in repairs, complete all as specified and directed.

PVC low level flushing cistern valve less,syphonic action type of 10 ltrs capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, fixed in repairs, complete all as specified and directed.

Vitreous china wash hand basin white, oval shape of size 580x400mm with PVC connection (15x450)mm long with PTMT nuts and PVC washer and including cutting for pinning in ends brackets and provision of GI waste pipe 32mm (light grade) of adequate size and length , brass chromium plated waste coupling 32 mm dia, fixing and taking down unserviceable wash hand basin, complete all as specified and directed .

15mm dia CP pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and directed.

PVC 'P' or 'S' traps of 110 mm dia including dismantiling of old traps, complete all as specified.

25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in base course of floor surfaces, complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8mm thick ( Square or rectangular) area of each tile exeeding 0.06 Sqm but not exceeding 0.11 sqm as in floors laid over & including 15 mm thick screed bed in CM 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of floor, complete all as specified.

Non skid joint free ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match shade, pattern, laying etc of tiles, laid over and including 15mm thick screed bed in CM (1:4), complete all as specified and directed.

20 mm thick granite black (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including Screed bed or bedding layer of mortar 15mm thick for laying floor in CM 1:4 finished even & rough to receive top layer, complete all as specified and directed.

Glazed ceramic coloured joint free tiles 300x450mmx7mm thick for work vertical surfaces such as shirking / dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles laid over and including 15mm thick cement plaster in CM 1:4 ,including dismantling floor,hearth or wall tilling,cement mortar bedding (but not backing), terrazzo toping all as specified and directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

75 mm thick PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in plinth protection etc finished even and smooth without using extra cement, complete all as specified and directed.

Pressed steel frames (factory made) made out of 1.25 mm thick black MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete size of frame 125x60mm including bottom of each chowkat to be welded with 2 Nos 25x3mm thick flat iron projecting 10 cm on either side, including one shop coat of red oxide zinc crome primer etc. Complete all as specified and directed.

Plain Cement Concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in back filling of pressed door frames, complete all as specified.

Plain framed panelled shutters factory made 35mm thick of 2nd class hard wood rail and style (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12 mm veneered particle board with commerciel venering on both faces. the size of rail and style as per IS:1003 (part I) kiln seasoned and chemically pressure treated, complete all as specified.

35 mm thick 2nd class hard wood factory made glazed & skeleton shutters, open rebated & prepared to receive glass gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a); complete all as specified and directed.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing all as specfied and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC strip of 20 mm width stuck in side with solvent cement for style and plain colour PVC sheet for top rail, lock rail and bottom rail on either side as in gap insert for top rail and bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement with and including suitable size mild steel butt hinges suppling and fixing in the frame at site ( Stiles and panels to be used of different colours) as per specification and drawing complet all as specified and directed.

Steel windows with side hung double shutters (window consisting of two shutters out side and two shutters of similar dimension inside of single MS Frame) box type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work) dovetailed or welded complete all as specified and directed.

Steel Ventilator with side hung double shutters (Ventilator consisting of one shutters out side and one shutters of similar dimension inside of single MS Frame) hung shutter type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work) dovetailed or welded complete all as specified and directed.

Galvanised mild steel wire cloth 0.45 mm nominal dia or wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple, fixed, complete all as specified and directed.

3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane and hacking out old broken glass (any thickness size and quality or description ) from metal / steel frames including punching or drilling out old glazing pins / spring clips and providing and fixing new ones all as specified.

3mm thick sheet glass, ordinary quality glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, welded to steel frame work, complete all as specified.

125 mm long extruded Aluminium handles, fabricated type, anodised complete all as specified.

150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified.

300mm long MS ordinary halical or rat tail rod pattern springs including roller and roller plate, complete all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed 300mm long, complete all as specified.

Steel locking bolt with mild steel electro galavnised plate and bright bolt not less than 10mm dia , 100 mm size, complete all as specified.

Rendering 15mm thick plaster in cement sand mortar 1:4 on fair faces of brick wall or concrete surface mixed with & liquid integral water proofing compound as per manufacturer's instructions all as directed by Engr-in-charge. (WPC shall be measured and paid seperately)

Supply only Liquid water proofing liquid admixture of approved make, complete all as specified.

Rendering 15 mm thick plaster in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even and smooth with out using extra cement, complete all as specified & directed.

Rendering 5 mm thick plaster in cement mortar 1:3 on concrete surfaces as in ceilings finished even and smooth without using extra cement, complete all as specified.

Machine cut Kota stone slab flooring not less than 20mm thick, laid over & including 15 mm thick screed base in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sqm incl marble strip design as per direction of GE ( Marble will be measured and paid seperately), complete all as specified.

Machine cut Kota stone slab not less than 20mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per sqm, complete all as specified.

100 mm wide Marble stone not less 20 mm thick (of any type) work (table rubbed and polished) in floors for strip in kota stone flooring and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade laid over and inlcuding 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed.

Demolition or breaking up pipe ( AC or concrete) set in cement mortar of 100mm/75mm bore of pipe, complete all as specified and directed.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and side of RCC/PCC bands in wall, horizontal or sloping and similar work exc 5 cm but n exc 10 cm wide for fair finished surfaces, complete all as specified and directed.

TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

RCC nominal mix 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in slab supported on walls, beams, column etc for kitchen/ bathroom counter for WHB, complete all as specified.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified.

110 mm bore PVC (SWR) bends provided with oval access door any radius, fixed in repair, complete all as specified.

PVC (SWR) junction, single (single T) equal or un equal 110 mm bore fixed, fixed in repair, complete all as specified and directed.

PVC (SWR) vent cowl for 110mm dia, complete all as specified.

75 mm bore PVC (SWR) bends provided with oval access door any radius, complete all as specified.

PVC (SWR) junction, single (single T) equal or un equal 75 mm bore fixed, complete all as specified and directed.

75 mm dia PVC (SWR) multi floor trap plain with grating including jointing with solvent cement, complete all as specified.

Preparation of new plywood surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified and directed.

Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified.

Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in single shade, complete all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

Applying two coats of cement base paint including preparation of newly plastered surface on walls complete all as specified.

Complete removal of existing treatment (scrubbing, washing down etc) of old treated or painted surfaces of wall & applying two coats of cement base paint on wall including preparation of old plastered surfaces, complete all as specified.

Complete removal of existing treatment, rubbing down and stopping of distempered, white wash or any type of treatment and applying two coats of oil bound distemper over a coat of alkali resistant primer on old plastered surface of wall, complete all as specified.

Preparation of newly plastered surface of wall and applying two coat of oil bound distemper with and including wall care putty 3mm thick over plastered surface of wall , white or tinted shade, complete all as specified.

Prepartion of old treated plaster surface of wall and applying one coat of white wash, complete all as specified and directed.

Prepartion of newly plastered surface of wall and applying one coat of white wash, complete all as specified and directed.

Preparation of newly plastered surface of ceiling and applying three coat of white wash, complete all as specified and directed.

Applying one coat of white wash on ceiling including preparation of old decorated surfaces, complete all as specified & directed.

Supply and fixed in repairs chromium plated shower rose of 125mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and as directed.

E&M PORTION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into CI/pressed steel terminal boxes not less than 2mm thick, including 3.00mm thick laminated sheet cover of hylam brand IS-2036 marked, for mounting switches, sockets, fan regulators etc for one light/fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

Description all as per srl item No-90 here in before but for one 3 pin socket outlet 6 amp as on independent board complete all as specified.

All as per item No. 90 above but for 3 pin 5 Amps on same board with cable 1.5Sqmm size, all as specified and directed

Description all as per srl item No 90 here in before but for one 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for main wiring and 2.5 sqmm as in continuous earth wire.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Switch socket multipurpose combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal,complete all as specifed.

Switch socket multipurpose combination 2 in 1, 2 pin & 3 pin, 6 Amp flush type universal,complete all as specifed.

Ceiling rose surface bakelite 65mm x 50mm (ISI Marked) 3 terminals PVC/poly carbonate, insulated body, compete all as specified.

Tube light fitting integrated type slim 20 Watt efficancy 125 lumens / watt, extruded aluminium housing, PC diffuser complete with housing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to light fitting, complete all as specified and directed. Make:-Crompton Greaves Model Bright Linea Cat Part No CCS-100-20-65-HL2-DP-NWH or Equivalent cat part of make as specified in Appx 'F' here in after.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings with and including LED lamp 9Watt, complete all as specified and directed.

Fan regulator two module 80 W, stepped type (electronic ) flush type for 1200/1400mm sweep AC ceiling fan, complete all as specified. .

Factory made epoxy powder coated distribution board TPN 4 ways (TPN MCB DB) with metal door (IP-43 Protection) Fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, stranded DIN rail, earth bar and cable ties for cale management, top and bottom removable gland, plates with knockouts and suitable for ohne FP-MCCB 40/63 Amp as incomer and SP/TP MCBs outgoing complete all as specified and confirming to IS : 8623. Make : C&S Cat No. CSDBMCCBDD041P43S or or equivalent cat part of make as specified in Appx 'F' here in after.

Factory made epoxy powder coated distribution board SPN 12 ways (SPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including DIN rail, earth bar and cable ties for cale management, top and bottom removable gland plates with knockouts and suitable for one SPN/DP-MCB as specified and confirming to IS : 8623. Make Legrand Cat No 507622 or equivalent cat part of make as specified in Appx ‘F’ here-in-after

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, fixing in replacement, complete all as specified. Make:- Legrand cat part No-5076 20 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB four pole 63amps 415 volts 50 Hz, 10 KA breaking capacity, complete all as specified.

MCB single pole and neutral 06 to 32 amps 240 volts 10 KA 'C' series fixing in replacement, all as specified. Make:- Legrand Cat Part No 4086 18 or Equivalent cat part of make as specified in Appx 'F' here in after.

MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series fixing in replacement, all as specified. Make:- Legrand cat part No-4085 87 to 4085 95 or Equivalent cat part of make as specified in Appx 'F' here in after.

Sub main wiring with single core cable 2 x 6 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including 20mm rigid PVC conduit (Concealed) medium grade alongwith 1x 4 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface, complete all as specified and directed. Note:-2 wire of 6sqmm, 1 wire of 4sqmm and one run of PVC conduit shall be measured as one unit.

Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh, 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection pipe, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- Rate for earth lead wire & protection pipe upto 7.5mtr length are inclussive in this item & no extra payment shall be admissible for the same.

Excavation in trenches in any type of soil not exceeding 1.5m wide and n.exc 1.5 mtr in depth for laying / taking out of under ground electric cable and getting out complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified.

Removing excavated surplus materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified.

Dry river sand cushioning to UG cable 8 cm thick before laying and 15 cm thick after laying complete all as specified and directed. Note:- (a). Dry fine sand of best available quality shall be used. (b). Punned thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

GI pipe medimum grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts, road crossing etc with fixing clamps, nuts bolts, washer of requrered size if required, complete all as specified.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 50 Sqmm x 3.5 core, complete all as specified.

Sub main wiring concealed type with four Nos single Core PVC insulated unsheathed multi strand copper conductor FRLS cable of size 10 Sqmm and two Nos single core PVC insulated unsheathed multi stand copper conductor FRLS cable of size 6 sqmm as in continuous earth wire confirming to IS 694 drawn into and including rigid non-metallic ISI marked PVC conduit medium grade 32 mm dia concealed in wall complete with fittings and fixings accessories complete all as specified and as directed by the Engr-in-Charge. Note:-2 wire of 10sqmm, 1 wire of 6sqmm and one run of PVC conduit shall be measured as one unit.

Factory made epoxy powder coated distribution board TPN 8 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp Copper bus bar, neutral bar, stranded DIN rail, earth bar and cable ties for cale management, top and bottom removable gland plates with knockouts and suitable for one FP-MCCB 40/63 Amp as incomer and SP/TP MCBs outgoing complete all as specified and confirming to IS : 8623. Make : Legrand Cat No. 507622 or equivalent Cat Part of make as specified in Appx ‘F’ here in after.

Supply and fixing MCCB four pole, 63A, 415 volts, breaking capacity : 25KA. Fixed overload and fixed short circuit all as specified and as directed by the Engineer-in-Charge. Make : Legrand Cat No 420053 or equivalent Cat Part of make as specified in Appx ‘F’ here in after.

Supply and fix MCB TP-32 Amp, 415 Volts 50 Hz AC supply, 10KA, C Curve, complete all as specified..

M/S TRIKUTA BUILDERS

KAMAL CONSTRUCTION

Tawi Constructions

NARESH KUMAR AND COMPANY

Kanwal Nain Behl