PROVISION OF OFFICERS ATTACHED TOILET IN BUILDING NO.P-37,P- 29,P-12,P-19 AND P-7 AT SARAIBARI ,PROVISION OF SCOOTER PARKING NEAR JCO,S MARRIED ACCN NEAR BLDG NO.P-5 AT ROWRIAH AND SPECIAL REPAIR TO ROOF,

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

Dismantling of Asbestos cement/CGI (corrugated, semi corrugated etc) sheets in roof covering complete all as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil, each n exc. 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n exc. 50 m and making good surface, complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil ,complete all as specified and directed.

Excavating over areas, n exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Returning filling in soft/loose soil, including, spreading levelling watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 Metres and depositing where directed at a level n. exc. 1.5 M above the starting point complete all asspecified and directed.

Materials and Labour for, broken stone or boulder hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface , complete all as specified and directed.

M & L for providing PCC 1:2:4 type B1 using 20mm graded aggregate louvres and jallies, 25mm thick (measured solid), including all mouldings including frame (precast frame shall be included) set in CM 1:4 complete all as specified and directed.

Materials and Labour stone kerb of machine pressed finish precast cement concrete(1:2:4) type B-1 using 20mm graded stone aggregate,block of size 300X300X150mm thick finished at top bullnosed shape and finished surface jointed in CM(1:4) struck finished , complete all as specified and directed.

Materials and Labour for plain cement concrete (1:4:8) Type D-2 using 40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) Type C-1 using 20 mm graded aggregate in foundations, filling , mass concrete and embedding of post etc complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregate in lintels up to 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary from work complete all as specified and directed.

M & L for RCC M-20 design mix in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-20 design mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete ,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-20 design mix in chajjas,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-20 design mix in beams, cantilever, bressumers, lintels over 1.5M Span,complete all as specified and directed.

Materials and Labour for reinforced cement concrete M-20 design mix in columns; pillars; piers; posts; struts etc,complete all as specified and directed.

Materials and Labour for plain cement concrete (1:2:4) type B1 using 20 mm graded aggregate as in surface channels and drains complete all as specified and directed.

Materials and Labour Extra for forming fair finishing to surfaces channels/drain 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, etc complete all as specified and directed.

Supply only integral water proofing compound all as specified

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:6), complete all as specified and directed.

Materials and Labour for brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in built in CM (1:4),complete all as specified and directed.

Materials and Labour for,cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, in stone concrete block or slab walls, complete all as specified and directed.

Materials and Labour for brick work with Sub Class ‘B’ bricks straight or curved on plan exceeding 6M mean radius built in cement mortar (1:4), complete all as specified and directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sided and soffits of plinth beams and similar works; vertical or to batter for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to chullah hoods, chajjas,troughs and similar items including edges for fair finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings , girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete, flat, complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed.

Supply and Fix, factory made rigid lam PVC door frame of size 125 mm x 50 mm, double rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet 'C' channel of 5mm PVC foam sheet of size 35mm x 35mm x 25mm & 40mm x 55mm x 40 mm & 25 mm x 35 mm x 35 mm using solvent cement, the two side 'C' channel shall be reinforced with 19mm x 19 mm MS square tube of 19 SWG with all three 'C' ed to flat base of 5mm PVC sheet with solvent cement. The profile shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube inside the 19 mm square tubes. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 08 Nos. of screws shall be provided for each vertical member and minimum 04 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm single side prelam PVC sheet with edges painted to match with prelam sheet, reinforced with MS square tube, fixed in opening, complete all as specified and directed.

Supply and Fix, factory made wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and Fix, factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

Materials and Labour for, Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

Supply and Fix, mild steel butt hinges, medium weight, cold rolled 100 mm size complete all as specified and directed

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

Supply and Fix, extruded aluminium alloy handles, fabricated type, anodized, 150 mm size, complete all as specified and directed.

Supply and Fix, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and with overall length of cover plate 150 mm, fixed in floor, complete all as specified and directed.

Supply and Fix, stainless steel, 300 mm, ordinary rat-tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and Fix, Aluminium Alloy, anodised, sliding door bolt, length of bolt 300 mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and Fix, stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix mild steel TMT bars 10 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 8 mm dia. and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed

Supply and fix mild steel TMT bars 5 mm dia. and over up to and including 10 mm dia. in stirrups, spacers, binders etc. cut to length, bend to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

S&F Rolled mild steel Roof trusses (framed), trussed purlins crane gantries, rails & fastenings & heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. GDE Fe410-0 or Fe 310-O complete all as specified and directed

S & F 5-10mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed

Materials and Labour for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Grade E-165 complete all as specified and directed.

Supply and Fix, Rolled Mild Steel, Fe 410 W (Grade E- 250) Quality-B, in plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachments, complete all as specified and directed.

Materials and Labour for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St.-240, complete all as specified and directed.

Supply and fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and directed.

Supply and fix Steel ventilator with centre hung shutters including two pairs of brass cup pivots,catch spring and pulley wheel all as specified and directed.

S & F rolled mild steel work in joist, channel, angle, or tee sections, fixed independently, without connecting plates etc., cut to within 20mm of the length indicated, quality confirming to GDE Fe-410-S complete all as specified and directed.

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.Make(Tata bluescope/CRIL/Sexena Marine Tech )

Material and Labour for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws, complete all as specified and directed.

Material and labour for (seamless) suspended ceiling which includes GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and web of 27mm) along with perimeter of ceiling, fixed with screw to brick wall with half of nylon sleeves and screws at 610mm center to center. Then suspended GI intermediate channels of size 450mm (0.90mm thick with two flange of 15mm each) from soffit at 1220mm center to center with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit, trusses rafters or pipe etc. with GI cleat and steel expansion fasteners Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with the half of connection clip and in direction perpendicular to the intermediate channel at 457mm center to center 12.50mm thick gypsum board (conforming to IS-2095-1982) is then fixed with screw to ceiling section with 25mm dry wall screw at 230mm center to center. Screw fixing is to be done mechanically either with the driver or drilling machine with suitable attachments. and then finally the boards are to be jointed and finished so as to have flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint proper tape as per manufacturer instruction all as specified and directed

Material and labour for pre-fabricated glass fiber reinforced gypsum beads/cornices architecturally beautifully crafted decorated 100 mm wide all as specified and directed.

Supply and fix pre-fabricated glass fiber reinforced gypsum mouldings/ corners of approved architectural design and make all as specified and directed

Material and labour for pre-fabricated glass fiber reinforced gypsum mouldings of Architectural design of circular panels n.exc 75cm dia all as specified and directed.

Materials and Labour for exposed metal frame ceiling with 6mm thick high pressure steam cured (HPSC) non asbestos fibre reinforced cement designer building boards for fixing in 600 mm x 600mm grid with and including exposed metal frame using hot dip galvanised steel, exposed pre-coated ceiling suspension system of grid size 600 mm X 600 mm, with main runner ‘T’ section 24 mm (W) X 38 mm (H) X 0.40 mm (T), cross ‘T’ section 24 mm (W) X 28 mm (H) X 0.30 mm (T) , wall angle 24 mm X 24 mm X 0.43 mm (T) and suspended with 4 mm dia. GI hangers/wire fixed with steel dash fasteners from purlins/soffits spaced at 1200 mm centre to centre with butterfly clips, hold down clips, providing provisions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc., complete all as specified and directed. Make of Grid Armtrong

Materials and Labour for 25 mm thick plain cement concrete (1:2:4) type B0 using 12.5 mm graded aggregate as in floor/paving/hardstanding/DPC , complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregate as in sub base in floor/paving/hardstanding , complete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:4:8) type D2 using 40 mm graded aggregates as in sub base of floor/pavings/hardstanding, complete all as specified and directed.

Materials and Labour for,Digital glazed ceramic coloured tiles, 600 X 300 X 7mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 10mm thick rendering cement mortar(1:3)complete all as specified and directed.

Materials and Labour for 100 mm thick plain cement concrete (1:2:4) type B2 using 40 mm graded aggregates as in sub base of floor/pavings/hardstanding/bed of septic tank, complete all as specified and directed.

Materials and Labour for, Digital Non - skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6),complete all as specified and directed.

M & L for Vitrified ceramic tiles dark Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

M & L for Vitrified ceramic tiles dark Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm, as riser of steps, skirting, dado and pillar laid with and including 15 thick rendering Cement mortar (1:3) complete all as specified and directed

Materials and Labour for pre cast reinforced cement concrete (1:2:4) Type B1 (using 20 mm graded aggregates) in landings, covers slabs (for man holes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4), complete all as specified and directed. Note: - Reinforcement will be measured and paid separately.

Materials and Labour for Granite (of any type) tiles 18-20mmthick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with and including 20mm thick cement mortar 1:3,complete all as specified and directed.

Material and Labour for Machine Pressed Precast Concrete Interlocking Paver Block ,with grey cement and pigment, any shape and size conforming to IS 15658-2006, of 60 mm thickness, M-35 Grade,laid on pavements,with and including 30mm thick sand cushion compacted in two layers with joint filled complete all as specified and directed.

Materials and Labour for rendering 10 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surface in walls,complete all as specified and directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound will be measured and paid separately)

Material and Labour for applying two coat of100 % Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including 1mm wall care putty premium quality over a coat of primer to new plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

M&L for preparation of new plastered or un -plastered from walls, and applying two coats acrylic distemper on walls, over and including a coat of 1 mm thick white wall care putty complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

Material and Labour for applying two coats of cement-based paint, white or tinted over and including cement base primer to new plastered surfaces on walls,including preparation of surfaces complete all as specified and directed.

Materials and Labour for applying two coats of interior emulsion paint silk glamor brand or equivalent any shade and colour to new plastered surfaces on walls, over and including 1mm thick wall care putty premium quality over priming paint as manufacturer,s intruction and including preparation of surfaces, complete all as specified and directed.Note Work shall be executed through authorised applicator of manufacturer,s paint Paint manufacturer Make Berger(Silk luxury)/J&N Special effect Insta colour/Asain(Royale)/Nerolac(Impressions) Note Work shall be executed through authorised applicator of manufacturer,s paint and got approved by GE before commencement.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed.

Preparing surfaces of wood and wood based materials,steel and iron work, new or old,of any description and girth,not otherwise described,applying two coat of black bituminous paint complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 15 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor, complete all as specified and directed.

Materials and Labour for galvanized steel tubing, medium grade, 25 mm bore with all fittings, laid in trenches, complete all as specified and directed.

Material and Labour for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part – I complete, all as specified and directed.

Materials and Labour for, Ball valves high pressure of PTMT (Minimum weight 210 gms) with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe, 20 mm bore and fixed complete all as specified and directed.

Supply and Fix, bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed. Make:Cat No.QQT-7037 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, stop valves/Angle cock, cast copper alloy, fancy type, chromium plated,screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 15 mm bore, complete all as specified and directed.Make:Cat No.QQT-7053 of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for steel pipe of for unions, 20mm bore, complete all as specified and directed. (Make:Jaquar/Marc/Kohler)

Supply and Fix, pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, 15 mm bore, including taking down existing unserviceable one complete all as specified and directed.Make:Cat No.QQT-7011 of Jaquar or equivalent make of Marc/Kohler)

Supply and Fix, brass chromium plated shower rose 125mm size,with swivel joints, fixed to steel pipe or union 15 mm bore, complete all as specified and directed.Make:Cat No.MSR-1060 of Marc or equivalent make of Jaquar/Kohler)

Supply and Fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. Make Cat no. CAN-CHR-1171N of Jaquar or equivalent make of Kohler/Marc

S & F hat pegs, solid body, 125mm to 175mm, brass complete all as specified and directed.

Supply and Fix, brass chromium plated, Towel Rack 600mm long with Lower Hangers including taking down existing one complete all as specified and directed.Make Cat no.AQN-7781 of Jaquar or equivalent of Marc/Kohler

Supply and Fix, toilet paper holder brass chromium plated complete all as specified and directed.

S&F chromium plated Health Faucet 15mm dia complete all as directed. (Make- Jaquar cat No-ALD-CHR-583 or equivalent of Marc /Kohler)

Supply and Fix vitreous China wash down water closet pan (pedestal pattern), white, (including fixing bolts,seat cover and flush pipe connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe etcas per existing specification complete all as specified and directed.

Supply and Fix, gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe, 20 mm bore, complete all as specified and directed.

Supply and Fix,sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm,complete all as specified and directed.

Supply and Fix, vitreous China wash basin, white, flat back, size 505 X 605 X 475 mm excluding taps, waste chain and porcelain stopper, but including brackets and half pedastal,complete all as specified and directed.Make:Cat No.FNS-WHT-0606 of Jaquar or equivalent make of Marc/Kohler)

Materials and Labour for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Supply and Fix PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, complete all as specified and directed.

Supply and Fix , brass chromium plated soap dish, , fixed with brass chromium plated screws, complete all as specified and directed. (Make Cat No.AQN-7731 of Jaquar equivalent make Marc/Kohler)

Supply and Fix, Towel ring brass chromium plated, complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 600 mm,complete all as specified and directed.

Cutting into existing manholes for connecting new drains (Internal dia. of pipe 100mm) , making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required,complete all as specified and directed.

Supply and Fix, two way bib tap, cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.:Make:Cat No.CON-041KN of Jaquar or equivalent make of MARC/Kohler)

Supply and Fix 32 mm bore low density polyethylene (LDPE) pipes waste pipe of wash hand basin with suitable fixing arrangement to waste coupling, complete all as specified and directed

M & L for salt-glazed stone-ware gully traps of 150x100mm sized, square or round mouthed, type ‘P’complete all as specified and directed.

Supply and Fix, 75 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints,laid in trenches or in floors, complete all as specified and directed.

Supply and Fix, 110 mm bore UPVC (SWR) pipes, single socketed in any length with rubber ring joints,laid in trenches or in floors, complete all as specified and directed.

S&F 110mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

S&F 75mm dia PVC(SWR) junction single, (single T) equal or unequal with access door complete all as specified and as directed.

Supply and Fix, 75 mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

Supply and Fix, PVC (SWR) floor trap, plain with grating including jointing with solvent cement with dia. of out let 75 mm, complete all as specified and directed.

Supply and Fix, 110mm bore PVC (SWR) bends any radius, with access door, complete all as specified and directed.

S & F 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for concealed type wiring using approved colour coding as per IS for one light/ fan/ bell point controlled by one switch with1.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

M&L for concealed type wiring using approved colour coding as per IS for switch socket combination 15 amps 5/6 Pin point on Independent board with2.5 Sqmm (Nominal area) PVC insulated, unsheathed, multistranded copper, conductor cable FRLSH (1100Volts grade) drawn in and including heavy duty PVC rigid conduits of 20/25 mm dia with all fittings and accessories alongwith PVC insulated multi stranded copper conductor of size 1.5 Sqmm as earth continuity conductor including fixing of 1. 22mm thick MS sunk terminal box duly flushed to wall with 3mm thick plastic laminated/ebonite sheet cover fixed with brass screws,cap and washers complete all as specified and as directed. Note:- (i) The chases in the wall shall be cut with elect cutter (ii) The disturbed surfaces of wall shall be made good with cement plaster 1:4 including matching the surfaces with as per existing finishes and to the entire satisfaction of Engineer in Charge

Materials and Labour for two single core FRLSH PVC insulated unsheathed cable 6.00 Sq. mm. (Nominal area) with multi stranded copper conductor cable, 1100 Volts grade, drawn in PVC Casing and Capping and continuous earth wire of single core FRLHS PVC insulated, unsheathed cable 4.00 Sq. mm (nominal area) with multi stranded copper conductor cable, 1100 Volts grade for sub main wiring, complete all as specified and directed.

Supply and Fix, switch piano, flush button, single pole, one way, 5 Amps, complete all as specified and directed.

Supply and Fix, ceiling rose, three terminal, PVC/ Polycarbonate insulated body, complete all as specified and directed.

Supply and Fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings,complete all as specified and directed.

Supply and Fix, switch socket combination 3 pin 16A, flush type, complete all as specified and directed.

Supply and Fix, LED lamp, 10 Watts, lumen output 770 lm, colour temp 6500 K, lamp current 0.04 amp, lamp base cap B22, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, 20W, 240 Volt, LED tube light as per Havells Cat No. LHEXBLP7PN1W020 or equivalent of philips/Bajaj/wipro and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S&F Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body environmental friendly, 8W, 240 Volt, LED tube light as per Wipro Cat No. LL20-111-XXX-65-NE or equivalent of philips/Bajaj and including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from light fitting to point outlet, complete all as specified and directed.

S & F 35 Watt 230 volt 50 Hz LED type new generation energy saving building security light luminiries housing is of versatile pressure die cast aluminium IP 66 with high power LED light complete with ballast/charging unit including of all accessories prewired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 2 m of length fixed to pole/wall etc and testing with and including 1.5mtr GI pipe 40mm dia light grade bracket bend to shape ,clamps,nuts,bolts and washer complete all as specified and directed. Make: Wipro cat part No. LR02-391-XXX-57-XX or equivalent of philips/CG.

Supply and Fix, Heavy Duty Exhaust Fan with self closing metallic louvers, 300 mm sweep, 1400 RPM, Single Phase, 230 V, 50 Hz, all as per Model “Turbo Force” of Make ‘Havells’ or equivalent Model of Make ‘Usha’ / ’Crompton Greaves’/’Almonard’ and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

Supply and Fix, double door, sheet metal enclosure for DBs for mounting of MCB for 240 Volts, 6 way, with 200 Amps rated bus bar, Single Pole & Neutral,IP43 IK09 complete all as specified and directed. [Cat No.DBSPN006DD of Make L&T or equivalent Model of Make Legrand/Siemens]

Supply and Fix, miniature circuit breaker (MCBs), single pole, 240 Volts,10KA, 6-32 Amps complete all as specified and directed.

Supply and Fix, miniature circuit breaker (MCBs), single pole and neutral, 240 Volts,10KA, 40 Amps complete all as specified and directed.

M&L for cutting existing GI pipe 40mm Bore (dia) in postion for taking out branch connection 20mm bore dia inserting 1 Nos GI Tee of size 40X40X20 mm including providing new reducting tee ,all joints and jointing materials, including necesary excavation and earth work complete all as directed

Supply,laying, jointing and testing of LT, XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 10 sq. mm, 2 core, including with suitable size of lugs complete all as specified and directed.

Supply and filling in approved dry sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and directed.

Supply and laying common burnt clay building bricks, sub-class ‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

M/S SANTOSHI TRADERS

THE SUPPLY AGENCY