KNMT - 2024-25

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete 10 cum - FOOTING First Depth 2.00m

PLINTH BEAM

Supplying and filling in foundation and basement with filling Crushed stone dust in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four Crushed stone sand and eight aggregate) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) - Plane Surfaces - 0 to 3.30m

Square column - 0 to 3.30m

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. - Foundation and Basement

Above basement

Supplying, fabricating and placing in position Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in following Cement Mortar using best quality II class table moulded chamber burnt bricks of size 9" x 4-3/8" x 23/4" in CM 1:5 for foundation and basement including curing, etc., complete complying with standard specifiction. - In Cement Mortar 1:5 Upto Basement

In Ground floor

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two M.Sand) over 10 mm base layer plastering and pointing with white cement neatly as directed. - Glazed tiles of size 305X200X6 mm

Paving the floor with design Rajasthan kotta tiles (colour and shade as directed) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification

Special Ceiling Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Plastering with Cement Mortar 1:5 (One cement and Five Crushed stone sand ), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Painting 2 coats with approved emulsion paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no M.Sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three M.Sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Plain Cement Concrete 1:1.5:3 (One part of Cement, one and half part of Crushed Sand (M- Sand), three coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Providing and fixing Bitumen Pad for Expansion joint in between pavement slabs to 12mm thick and fixed as shown in the drawing including cost and conveyence of expansion joints including shalimar pad and joint sealent etc, complete as per standard specification

Laying with new C.C. Laminated tiles (Like Dora tiles Eurocon tiles etc),(anti skid) of 20mm thick of approved spl quality and set in Cement Mortar 1:3 (1 of cement and three part of P-sand ) 20mm. Thick using river sand and pointing with colour cement using at the rate of 0.40 kg/M2 and mixing with colour pigment at the rate of 0.3 Kg/M2 including finishing complete with Standard Specification and as directed by the Departmental Officers etc.,

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supply and fixing of Terocotta jally including cost and conveyance of all materials and labour charges etc complete.

Plastering with cement mortar 1:3 ( one cement and three P.Sand) mix to 20mm thick including cost and conveyance of all materials to site including curing etc.,complete as per standard specification – 10m2

Supplying and fixing in position white glazed Indian water closet of size 580 X 440mm of Orissa type of approved quality with 'P' or 'S' trap with sand cushion and forming flooring alround the closet using 40mm broken brick jelly lime concrete 1:2:5 ; 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes by dismandling masonry / RCC works and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works.)

Supply and run of 2 of 6 sq.mm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') bent at both ends with necessary angle iron up right and end supports for mains SD 71

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour SD 55

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC.unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable Colourfor open PVC light point / fan point (For electronic regulator) (5 points per coil) SD 24

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 mm x 100 mm x 113mm TW switch box in flush with wall with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point. SD 37

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. SD 88

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb SD 83

Supply and fixing of 1200 mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450 mm (18") SD 106

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board 1No 32 Amps DB MCB as incoming and 6 Nos 6 Amps to 32 Amps SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Standard make). SD 506

Supply and fixing of 32 Amps DP Switch of 500V with metal clad with fuse and neutral (Side Handle) on suitable TW Board with PWD Earthing SD 147

Supply and fixing of TNEB meter Board suitable for 32A Three Phase service connection with 3 Nos. 32A Fuse unit(500V) 32A neutral link and earth link (1" x 1/8" Copper flat) on TW plank of size 600mm x 450mm x 19mm withsupporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank onwall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit. SD 125

Supply and Delivery of 12.00 Mtr High Mast light System with all accessories, including Octagonal Pole with top Diameter 150mm and Bottom Diameter 350mm, Galvanizing Standard is 4759, Base Plate 450mm with thickness of 20mm, P.C.D 320mm, Metal Protection Hot-Dip Galvanization Internally & Externally, Material Construction Shaft Equivalent to BSEN 10025, 6mm Thickness, Thickness of Galvanization 70 microns Avg., Overhang CO-CENTRIC with RING Type Bracket. Free standing 8 sided octogonal continously tapered Galvanized Structure, Foundation Bolt M25x600mm (6Nos), LED focus light quantity of pole is 6 Nos, Manual operated forward-Reverse gears with steel rope and Wind loads for design is As per IS-675

Supply and Erection Of 150W LED Street Light Fitting with LED etc., complete as per standard specifications.

Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 4 x 25 sq.mm. LTUG armoured cable with earth connection etc., complete as per standard specifications.

Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay etc., complete as per standard specifications.

Foundation with a Bolt Size of M25*600mm in "L" Shape including 6 Foundation Bolts With a Template of 3800D*3mm and 2Nuts & 2 Plain Washers. Full Concrete Foundation with Sand and Cement in 5 Feet Height With 2 Feet Width and 2 Feet Length.(The rates has been adopted as per the lowest quatationn approved by Executive Officer.)

Providing Top Round for Fixing the Solar Fittings and Required Equipments.(The rates has been adopted as per the lowest quatationn approved by Executive Officer.)

Supply and Erection of Control panel is timer based automatic On-Off controller, Energy meter fixing provision with fuse units and Rain water proof powder-coated double door box.

Installation of Commissioning and Testing Charges etc., Complete as per standard specifications.

Transportation Charges etc., Complete as per standard specifications.

Supply and delivery and fixing of HDPE tank 1000 litres capacity as per IS 12701/ 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges as directed by departmetal officers.

supplying and fixing of ISI approved make PVC pips, Specials - 32mm pipe

25mm pipe

32mm Tee

32mm bend

32mm Coupling

25mm Tee

25mm bend

25mm coupling

32/25mm Reducer

25/20mm Reducer

PVC Tap

110mm PVC pipe

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanium colour sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.