Extension/Establishment of existing Laboratory area in Emergency of GMCH Jammu alongwith allied works in adjoining areas including upgradation of Trauma area.(Civil part)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms /sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm wide x1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of anglehanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board /calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board withrecommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board,all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 : 2011 (Board with BIS certification marks)

Engage carpenter for removal and refixing of doors

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1mm thick

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete

Providing and fixing PVC fitting accessories

75mm plain tee

110mm plain bend

110mm plain tee

110mm to 75mm reduction socket

Providing and fixing aluminium work for doors ,windows ,ventilators and partitions with extruded built up standard tubular section /appropriate Z sections and other sections of approved make conforming to IS :733 and IS :1285 ,fixed with dash fastner of required dia and size including necessary filling up of gaps at junctions i.e , at top ,bottom and sides with required EPDM rubber /neoprene gasket felt etc. aluminium sections shall be smooth ,rust free,straight ,mitred and jointed mechanically wherever required including cleat angle ,aluminium snap beading for glazing /panelling ,C.P brass/stainless steel screws ,all complete as per architectural drawings and the directions of engineer in charge (glazing ,panelling and dash fasteners to be paid for separately).

For fixed portion powder coated aluminium (minimum thickness of powder coat 50 microns )

For shutters of doors ,windows & ventilators including providing and fixing hinges /pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber /neoprene gasket required (fittings shall be paid separately ).Powder coated aluminium 50 microns.

providing and fixing glazing in aluminium door window ventilator shutter and partitions etc. with EPDM rubber /neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge with float glass panes of 5 mm thickness weight not less than 12.5kg/sqm

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

providing and fixing aluminium fitting of door closer complete job

Providing and fixing PVC panelling superior quality as per the direction of engineer in charge

Providing and laying gang saw cut of specified thickness, mirror polished/ flamed pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-inCharge. 18 mm thick

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia.0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (30mm) Second class deador wood

Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete. With Galvanized M.S. Wire gauge with wire of dia 0.63 mm With 2nd class teak wood beading 62x19 mm

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: Internal work (Parkash, Suyra Make) or equivalent expose on wall

15mm nominal

20 mm dia. nominal bore

25mm dia

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) (Unique/DRP make)

15mm Nominal

20 mm nominal bore

Providing and fixing PVC pipe including / jointing with seal ring (Finolex / Supreme) of pressure @ 4kg

75mm dia pipe

110mm dia pipe

Providing and fixing PVC floor trap of Finolex / Supreme OR equivalent

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing of PVC conection 450 mm long

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:

Flexible pipe 32 mm dia

Providing and fixing C.P fittings 15mm nominal bore and fixtures (jaquar/cera or equivalent)

Short nose bib cock

Long nose bib cock (kb1211033)

Angle valve

C.P gratings 4"

Soap dish

C.P. towel rod 2'-0"

Towel ring 200 mm dia

cp jet

handle 200mm

handle 150mm

tower bolt 150mm

tower bolt 100mm

C.P. Mixer

Looking glass

C.P. Extension Nipple 1"

Providing and fixing 19mm thick ply with fevicol and nails complete job

Providing and fixing superior quality of 1mm thick mica including grooving and fevicol nails complete job

Providing and fixing sliding bolt 300 mm x 16 mm

providing and laying cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) all upto plinth level

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand)

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Disposal of mulba including loading and unloading job complete

Engage Labour for dismantling and shifting of mulba from ground floor to outer side and shifting of construction material from outer area to working site and removing of old damaged false ceiling (to be paid as per actual)

Engage Plumber

Engage Welder with hire charges of welding set

Engage Sweeper

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040mm bowl depth 225mm

Engaged Aluminium Fitter for repair of old damaged false ceiling

Providing and dixing cup bords/Almirah frame and shutters with 6mm thick ply fixed over 19mm thick ply of supeior quality with decorative mica fixed on outer side of almirah of superior quality and plain mica of superioe quality on inner side of almirah shutters complete incluidn internal boxes / partitions with 19 mm thick ply of superior quality wherever required decorated with plain mica/enamel/emulsion complete wherever required including all fittings and fixtures as directed by Enginer-in-charge (complete job)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm. and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead for thickness of tiles 10 mm to 25 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in charge: 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in charge: 1:4:8 or leaner mix (i/c equivalent design mix)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointingin white cement mixed with pigment of matching shade complete.

Providing and fixing PVC pipe including / jointing with seal ring (Finolex / Supreme) of pressure @ 5.5 kg/Cm2

75mm dia plain bend

75mm dia door bend

110mm dia plain bend

110mm dia door bend

110mm dia door Tee

12mm Cement plaster of mix: 1:4 ( 1 cement : 4 fine sand)

15mm cement plaster on the rough side of the single side or half brick wall finished with floating coat of neat cement of mix 1:4

Providing and Fixing wall Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. Size of tile 600x600 m

Providing and fixing ACP SHEET of superior quality, complete job

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required : size 450 x 300 x 150 mm

Providing and fixing Brass Ball Valve

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with White P.V.C automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required: Single half stall urinal with 5 liter P.V.C automatic flushing cistern.

Please Enable Macros to View BoQ information