SPL REPAIR TO TOILET BLOCK AT PT GROUND AND NEAR MAIN GATE OF ARMY AD CENTRE INCLUDING CERTAIN LBW WORKS AT GMS UNDER GE I GOS

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of floor hearth or, walls tiles including bedding but backing and rubbish off permises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exceeding 0.18 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 for laying of floor tiles complete all as specified and directed.

M&L 40 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm grante stone aggregate as in floors including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed.

M&L for glazed ceramics coloured tiles of size 450x350x7mm thick in vertical surfaces such as skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed..

M&L for 10 mm thick plaster in cement mortar 1 : 4 for fixing of wall tiles complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed.

M&L Brick work with Fly Ash bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brick work with Fly Ash bricks bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 in half brick thick wall complete all as specified and directed..

M&L for PCC 1:3:6 type C1 using 20mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for PCC 1:2:4 type B1 using 20 mm graded stone aggregate for insertion of hold fast incl necessary form work etc complete all as specified and directed.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and directed.

Supply only water proofing compound (liquid), ISI marked.

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

All as per item No 18 above but exc 1.5 Sqm but n.exc. 4 Sqm each.

M&L 2nd class hard wood plain solid straight chowkhat & frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

S & F factory made 40 mm thick Flush shutters solid core constraction, with block board core and ply wood face panels comercial type on both sides complete all as specified and directed.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube supplying & fixing in opening as per specified & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long complete all as specified and directed.

S & F in repairs Aluminium anodised barrel Tower Bolt of size 150 mm of extruded section complete all as specified and as directed.

S&F 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F 100 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re-fixing complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down 25 mm bore steel tubing and connections complete all as specified and directed.

M&L for Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S & F 25 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S& F in repairs Counter Wash hand basin fixed on Granite/Marble or other appropriate top coloured including chromium plated waste coupling and PVC connection complete all as specified and directed.

S&F in repairs white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed.

S&F in repair vitreous china squating pan 'Orissa' pattern WC size 580x440 mm white with integral foot rest and trap and including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified and directed.

S&F in repair chromium plated health faucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete all as specified and directed.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and directed.

S&F in repair bib tap 15 mm bore,fency type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed..

S&F in repair CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair stainless steel soap dish, of standard size and shape complete all as specified and directed.

S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed.

S&F glass shelf assembly cosisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long complete all as specified and directed.

M&L for 18 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F MS TMT bar 8 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90 mm dia or security with clips complete all as specified and directed.

Taking down AC/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of any dia pipes complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

M&L PVC(SWR) bend of 110mm bore of any radius etc complete all as specified and directed

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia complete all as specified and directed.

M& L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed.

S&F PVC (SWR) bends any radius provided with access door of 75 mm dia complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm bore complete all as specified and directed.

All as per item No 65 above but 75 mm bore

S&F PVC (SWR) vent cowl 110mm bore

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete all as specified and directed.

S&F PVC (SWR) 'P' trap for 110 mm dia etc complete all as specified and directed.

Dismantling water tanks and removing to store of capacity exc 500 and n exc 1000 ltrs complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity complete all as specified and directed.

S&F Ball valves 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete all as specified and directed.

S&F in repairs Gun metal, globe or gate valve with iron wheel head, 25 mm bore, screwed both ends for iron pipe complete all as specified and directed.

M&L for preparation of of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete all as specified and directed.

M&L for Preparation of old wooden surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall or concrete surface over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for Preparation of surfaces of ceiling and applying two coats of white wash complete all as specified and directed..

M&L preparation of old decorated plastered or unplastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots to obtain smooth surface and applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on plaster wall surfaces complete all as specified and directed.

Taking down existing water proofing membrance and cleaning roof, plastered surface etc preparing the surface to receive plaster by brushing with wire brush and fanning the surface to remove all loose dirt etc and brushing neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in sub base flooring 40 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed.

M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 with water proofing compound 3% by the weight of cement complete all as specified and directed. (Note Integral WPC will be measured and paid separately)

M&L for water proofing treatment to roof surface complete all as specified & directed with the followings :- (a) Apply bituminous based primer confirming to IS: 3384-1965 @ 0.30 kg/sqm. (b) APP modified bituminous membrane 3mm thick with non woven polyester core of weight not less than 3.2 to 3.5 Kg/sqm laid and bonded to the sub strata by heat process, over laps of 100mm shall be sealed/fused by flame torch application as per manufacturer instructions. (c) Applying bituminous based aluminium paint @ 0.20 Kgs/Sqm in two coats over APP membrane

S&F in repairs vitreous china urinals, flat back of size 465mmX355mmX265mm, white with grating and union for discharge pipe complete all as specified and directed.

S&F 32mm dia waste pipe of polythelene,flexible, for wash hand basin or urinals complete all as specified and directed.

S&F waste coupling of PTMT (half or full threaded) for 32mm bore complete all as specified and directed.

M&L precast RCC 1:2:4 type B1 using 20mm graded stone agg in shelves/cover slabs similar articles set in cement mortar 1:6 including all necessary form work (Note : Reinforcement shall be measured and paid separately).

M&L RCC 1:2:4 Nominal Mix using 20 mm gradded stone aggregate in slabs supported on walls, beams and columns in floor,roof,landing etc complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs floor slabs, landing and similar work for fair finished surface complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, break in floors, window cills, horizental or sloping and similar exc 10cm but not exceeding 20 cm wide for fair finished surface complete all as specified and directed.

M&L hard core of gauge 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed..

M&L Cement concrete type C-2, 1:3:6 using 40 mm graded crushed stone aggreates 100 mm thick as in flooring finished even and fair complete all as specified and directed.

M&L 50 mm thick Sand cushning below interlocking paver tile complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size fixing with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed..

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN Dbs/TPN DBs/ Main switch including old unserviceable MCCBs/ MCBs isolators etc and making good to disturbed surface site complete all as specified and directed.

M&L in repair for point wiring with 1.5 Sqmm signle core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including concealed PVC conduit of size 20/25 MM ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminted 3mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for following:- (a) One light point controlled by one , one way switch 5 Amp

(b) One fan/ exhaust fan point controlled by one ,one way switch 6 Amp

S&F in repair LED bldg security light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make Havells, Cat No enduraPearlsl25Wled757sasYtoPCmP or equivalent of higher cost.

S&F in repair LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F in repair Switch piano flush button single pole one way 6 Amps, complete all as specified and directed.

S&F in repair for Sheet metal enclosure factory made double door for mounting MCBs with 200A rated bus bar Scapacity SPN 4 way AC 240 Volts with IP-43 protection, complete all as specified and directed.

S&F in repair for Sheet metal enclosure factory made double door for mounting MCBs with 200A rated bus bar Scapacity SPN 8 way AC 240 Volts with IP-43 protection, complete all as specified and directed.

S&F in repair for Ceiling rose 3 terminals of PVC/ polycarbonate, as per relevant IS code, ISI marked isolated body complete all as specified and directed.

M&L in repairs earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less'than 1.5 meters below normal ground level, connected to galvanised iron earth lead wire of 4 mm dia GI pipe mediam grade 15 mm dia upto 7.5 mtr including provn of conrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25x25x3 mm with lugs 02 Nos and with 6.0 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for earth plate, common sald and charcoal filing, test point made out of Bronze/ Gun metal with fixing arrangement, funnel, wire mess and excavation/ earthwork in hard/ dense soil, to a distance not exceeding 50 mtr all as per electrical plate No 3 of SSR 2010 Part I and connecting to earth test point all as specified or indicated incl testing on completion.

S&Fin repairs 240V, 10KA 'C' curve miniature circuit breaker (MCB) of size 5 to 32 Amp SP and current carrying capacity in the MCB DB complete with connection testing and commissioning.

S&F in repairs 240V, 10KA 'C' curve miniature circuit breaker (MCB) of capacity 32 Amp SPN and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Taking down and replacement of existing unserviceable street light fitting bracket with new brackets made out of 32mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall, painting with two coats of aluminium paint over a coat of red oxide primercomplete complete all as specified and directed.

Supply installation, testing and commissioning step down outdoor type transformer with minimum one star BEE label as per statutory requirment of Buerau of energy efficiency Govt of India, 11/0.433 KV (at no load), transformer, 3 Phase, 4 wire AC, 50Cycle 500 KVA, copper wound, with off load manual tap changing arrangment of HT side to vary secondary voltage upto -7.5% with steps of +-2.5% including suitable cable entry boxes on both HT and LT side complete in all respect with standard accessories and fitment conforming to IS, 2026, DYN-11 connection complete all as specified and directed. Silent features of transformer as under :- (a) Transformer shall be oil immersed, naturally/self cooled, copper winding, MS radiator cooled tank complete with first fill of transformer oil dielectric strength not less than 50 KV as per IS 335 with test certificates with ON/OFF and cooling systems, temperature of oil shall not rise to 55 Degree centigraded to ambient and 55 Degree centigrade of winding. Transformer shall be painted with two coats of smoke grey apoxy paint conforming to IS 632. (b) Rating plate and terminal marking plate. (c) Two earthing terminal for body earthing and two additional for neutral brought out on a bushing. (d) Lifting lugs. (e) Thermometer pocket with stem type thermometer with maximum temperature indication and resetting device. (f) Air release valve with plug and cover. (g) conservator tank with oil indicator. (h) Clear view type silica gel Breather assembly including with Silica Gel. (j) Oil level indicator with maximum and minimum marking. (k) Oil filing hole with cover. (l) Explosion Vent. (m) Roller -04 Nos Note : After installation of transformer, testing shall be conducted by SEI of HQ CECC or by rep of accepting officer before commissioning.

M&L for fabrication of towing type transformer trolley suitable for 500 KVA transformer step down outdoor type 11KV/433 volts capacity complete made up of MS "L" beam of 250x125x6.9mm (37.3 Kg/mtr) and MS sheet for platform 6 mm thick (47.1 Kg Sqmtr) mounted on 4 wheels (7.50"x16" size) with rims mounted on 02 Nos front and rear axle wheel with leaf spring clamps cushioning arangement, between platform and 02 Nos front and rear axles complete with towing arrangement with tow hook to take full load of trolley and transformer, jalli (XPM) around platform on angle iron frame of size 40x40x5mm opeing arrangemnt from both side with locking arrangment for loading and unloading of transformer including welding, bending and drilling holes, spray painting with two coats of synthetic enamel paint over a coat of primer overall surface complete all as specified and directed by Engr-in-Charge (a) Size of the transfomer trolley platform shall be 3mtr x 2.5 mtr and sufficient space all around after transfomer installation for ventilation / maint purpose as recommended by OEM and accommodate HT/LT connecting cables loops on the platform (b) The trolley shall be provided with steel square net of suitable gauge fixed on angle iron in all around the trolley body with opening arrangement as protection Note :- (i) Any other works not mentioned in item above but required for smooth functioning of trolley shall be deemed to be inculded in the rate quoted by the contractor (ii) Drawing of trolley shall be approved by GE before fabrication in factory/ workshop

M&L for XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 11000 volts Earthed, grade cross sectional area 120 sq. mm complete all as specified and directed.

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 240sq. mm 3.5 core complete all as specified and directed.

M&L for Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 to 185 Sqmm complete all as specified and directed.

M&L for Cable jointing kit for 1.1 KV (Earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 240 to 300 Sqmm complete all as specified and directed.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm galvanised iron strip complete all as specified and directed.

V.Venkata Ramaiah

M/S K MURALIDHARA PATRA

ABC CONSTRUCTION COMPANY

M/s Bapujee Builders and Traders

MM ENGINEERING SYSTEMS

M/S S. N. ENTERPRISES