Construction of Block Level Stadium under Sukruli Block With Indoor hall_building

CIVIL WORK Earthwork in excavation upto 1.50mtr depth of foundation trenches for columns, basement, tie beams, walls and steps in all kinds of soil including ordinary soil, hard/gravelly soil and stony earth mixed with stone and boulders etc but not requiring blasting with initial leads an: d lifts including dressing and leveling the bed sides up to required depth and depositing the excavated materials at places away from the work site with T&P for shoring, shuttering, dewatering if required etc. complete as per the drawing, design including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge.

Extra lift of 1.5m or part there of over the initial lift of 1.5m in all kinds of embankments and road works and ordinary earth work in general.

Filling foundation trenches and plinth with excavated earth (excluding rock) including laying the earth in layers not exceeding 23.5cm (9inch) thick ramming and watering with all leads and lifts including cost of all labour, T&P etc. complete as directed by the Engineer-in-charge.

Supplying all labour, T&P for the Carriage of excavated earth by mechanical means of transport within 5.00 K.M. lead including hire and running charges of vehicles, labour charges for loading and unloading as required for the work etc. complete as per the direction of the Engineer-in-charge.

Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for complete the work as per direction of the Engineer-in-charge.

Providing, mixing and injecting chemical emulsion for pre - constructional antitermite treatment as per IS specification and creating a chemical barrier in bottom and sides of foundation trenches, top-surface of plinth filing junction of walls and floors along with external perimeter of the building expansion joints surrounding the pipes and cables at the rate of 7.5liters per Square Meters on vertical surface and 5.0liters per Square Meters on horizontal surface, 50% of the emulsion to be filled in the holes made in treanches at 150mm centre to centre (or as directed directed by the manufacture) etc. complete using approved quality of chemical emulsion of requisite quantity prescribed by the manufacturer as directed by the Engineer-in-charge including cost of all materials and labour taxes etc. complete. (Measurement should be taken as per plinth area and indemnity bond for warranty for 10 years to be furnished) .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing & laying cement concrete of prop. (1:3:6) in foundation bed and floors using 40mm nominal size down graded, screened, washed hard black crusher broken granite metal of approved quality & from approved quarry including laying in the layers not exceeding 100 mm thick, hoisting, lowering, laying, watering and curing etc. complete to the required levels including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for complete the work as per direction of Engineer-in-charge.

Brick work in foundation and plinth with flyash bricks of size 25cmx12cmx8cm in cement mortar (1:6) with best quality bricks having crushing strength not less than 75 Kg/cm2 immersing the bricks in water for not less than 6 hours before use (the bricks shall be free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) includes molding, chamfering, corbelling .complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. and as per direction of Engineer-in-charge.

Providing, lifting, hoisting and laying Reinforced cement concrete work of M-25 grade having minimum compressive strength of 250kg./cm2 in 15cm cubes at 28 days and in accordance with I.S. 456 and I.S. 516 using crusher broken hard black granite chips of approved quality & from approved quarry including laying and compacting concrete with vibrator, watering and curing for 28 days, cost of rigid and smooth centering & shuttering and finishing to exposed surface smooth providing, grooves or beads wherever necessary including cost, conveyance, royalties & taxes of all materials and cost of all labour, T&P etc. as required for complete the work in all respects as per drawing, design and direction of Engineer-in-charge. (But excluding cost of M.S. rod/Tor steel and binding wires and labour charges for bending, binding and tying the grills)Foundation

Plinth Beam

Beam & Column

Lintel

Roof Slab

Staircase

Chajja

Roof Slab at Double Height

First Floor-Beam & Column

Lintel

Roof Slab

Chajja

Second Floor-Beam & Column

Roof Slab

Providing & fixing TOR Fe-500 D grade reinforcement bars of approved makes for RCC work of required diameter with straightening, cutting, bending, binding welding and joining (if necessary) and tying the grills and placing in position as required for R.C.C. work and providing fan hooks, hoisting, lowering and laying including cost, conveyance and taxes of tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all heights as per the drawing, design and direction of Engineer-in-charge. (Linear measurements will be taken & quantity will be calculated on standard weight. Weight of binding wire will not be considered for measurement)Ground Floor

First Floor

Second Floor

Brick work in superstructure with flyash bricks of size 25cmx12cmx8cm in cement mortar (1:6) with best quality bricks having crushing strength not less than 75 Kg/cm2 immersing the bricks in water for not less than 6 hours before use (the bricks shall be free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) includes molding, chamfering, corbelling .complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. complete as per direction of Engineer-in-charge.Ground Floor

First Floor

Second Floor

Half Brick work in superstructure with flyash bricks of size 25cmx12cmx8cm in cement mortar (1:4) with best quality bricks having crushing strength not less than 75 Kg/cm2 imersing the bricks in water for not less than 6 hours before use (the bricks shall be free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) with provision of stiffner (2 Numbers of 8 m.m dia M.S. Round Reinforcement Bars at each 4th layers, paid separately) includes molding, chamfering, corbelling, complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. complete as per direction of Engineer in charge.Ground Floor

Providing 12mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to inside smooth surface of brick masonry walls after scraping, cleaning and racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.Ground Floor

First Floor

Second Floor

Providing 16mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to outside smooth surface of brick masonry walls after scraping, cleaning and racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.Ground Floor

First Floor

Second Floor

Providing 6mm thick plaster in C.M. (1:4) over ceiling, chajja, loft, staircase, column, beams and walls after removing the false if necessary, scraping, cleaning and close deep chipping including rounding of the corners, recess and roughening concrete surface where necessary, watering and curing, finished smooth over R.C.C. surface, including cost, conveyance, royalty, taxes of all materials, cost of all labour, T&P etc. complete as per direction of the Engineer-in-charge.Ground Floor

First Floor

Second Floor

Providing 12mm. thick cement plaster in all floors at all height with cement mortar of mix (1:4) finished smooth to inside smooth surface of half brick masonry walls after scraping, cleaning and racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.Ground Floor

Providing & laying best quality Vitrified floor tile of specified size of thickness 6-10mm of approved make confirming to IS-15622 specifications in floor over 20mm thick cement mortar (1: 4) to proper slope, line and level including cutting to required size and shape, fixing at corners and splays etc. Including finishing the joints with epoxy based water proofing grout to match the color and shade of tiles complete as per the design & drawing with cost of all materials, labour, conveyance T&P etc.Full body premium grade matt finish vitrified tiles of size 600mmx600mm All complete of approved quality & specification as per the direction of Engineer -in-charge.Ground Floor

First Floor

Providing & laying vitrified tile of specified size in skirting cut from approved make confirming to IS-15622 specifications over 12mm thick cement mortar (1: 3) to proper line and level to a height as per design including cutting to required size and shape, fixing at corners and splays etc. including finishing the joints with epoxy based water proofing grout to match the color and shade of tiles and complete as per the design & drawing with cost of all materials, labour, conveyance, taxes ,royalties,sundries and T&P etc. Full body premium grade matt finish vitrified tiles of size 600mmx600mm All complete of approved quality & specification as per the direction of Engineer -in-charge.Ground Floor

First Floor

Providing & laying best quality Vitrified floor tile of specified size of thickness 6-10mm of approved make confirming to IS-15622 specifications in floor over 20mm thick cement mortar (1: 4) to proper slope, line and level including cutting to required size and shape, fixing at corners and splays etc. Including finishing the joints with epoxy based water proofing grout to match the color and shade of tiles complete as per the design & drawing with cost of all materials, labour, conveyance T&P etc. All complete of approved quality & specification as per the direction of Engineer -in-charge. Suede /Rustic finish Vitrified Tile 600x600mm.Ground Floor

Providing and fixing ceramic glazed wall tiles of specified size of thickness 6-10mm conforming to IS: 15622 specifications of approved make and shade, in skirting and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and finishing the joint with epoxy based water proofing grout to match the shade. All complete of approved quality & specification as per the direction of Engineer -in-charge. Ceramic glazed Wall Tile 300 x 600mm.Ground Floor

Providing and fixing 16-18mm thick granite flooring of approved quality and size in floors, steps, landings, window sill etc in all floors at all height on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and washed sharp sand for mortar and grouted with neat white cement slurry jointing the tile with neat white cement slurry mixed with required quantities of pigments of approved marks to match the shades of the marble tile if required watering and curing, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work including rubbing mechanically and wax polishing etc. All complete of approved quality & specification as per the direction of Engineer -in-charge.Ground Floor

First Floor

Providing 16-18mm thick and above 0.40 Sqm size granite tile cladding of approved quality, colour and size in walls in all floors at all height on 12mm thick bed of cement mortar of mix (1:3) (1 Cement: 3 Coarse sand) finished with modular pointing in white cement & pigment to match the shade of the granite including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour curing sundries and T & P etc. required for the work etc.All complete of approved quality & specification as per the direction of Engineer -in-charge. Ground Floor

Providing edge moulding and groove cutting of required numbers as per drawing and design to 18 mm thick granite stone counters, steps, Vanities etc., including machine polishing to edge to give high gloss finish etc. All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supplying, fitting and fixing in position 25mm thick cement concrete tile of approved make, quality, colour and size in all floors at all height on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient grouted with neat white cement slurry with required quantities of pigments of approved marks watering and curing, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries. All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing kota stone flooring using kota stone of approved quality, colour and size of 18-20mm minimum thick in floors, treads on steps and landings in all floors at all height on 20mm thick bed of cement mortar of mix (1:4) laid in proper slope and gradient with screened and washed sharp sand for mortar and grouted with neat white cement slurry jointing the kota stone with neat white cement slurry mixed with required quantities of pigments of approved marks to match the shades of the kota stone, if required , watering and curing for 21 days, including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work including rubbing mechanically and wax polishing etc. complete in all respect as per specification and direction of Engineer-in-charge.

Supplying, fitting and fixing in position, 18-20mm minimum thick kota stone of approved quality and size in dadoes in all floors at all heights and riser of steps on 12mmm thick cement plaster (1:3) using screened and washed sharp sand for mortar with grouted with neat cement slurry and jointed with neat cement slurry mixed with required shade of pigments to match the shade of the tiles including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, curing-sundries and T&P, etc. required for the work complete as per specification and direction of Engineer-in-charge.

25 mm. average thick artificial stone flooring with cement punning laid to proper slope with cement concrete of proportion (1:2:4) using screened and washed sharp sand for mortar with black hard crusher broken granite stone chips of approved quality and from approved quarry, washed and cleaned laid in two layers i.e. the bottom layer being 19 mm . thick and top layer of 6mm. thick with 12mm. to 20. size black hard crusher broken stone chips (20mm size chips not to exceed 25%) including chipping and chiseling and cleaning the top surface of the floor slabs in upper floors, including rounding of corners, watering and curing with cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as directed by the Engineer-in-charge

Supply & Installation of Sports Vinyl Flooring of 7 mm thickness EN428. Anti Vius, Anti Bacterial, Heavy Metal Free, Phthalate Free. Weight 4350 G/Sq. Mtr EN430. Impact Sound Insulation 20 - 22 EN ISO 717-2 & EN ISO 140 - 8, Flammability class CFL - S1 EN13501 - 1, VOC Indoor Air Quality Floorscore Certified ( SCS - FS - 04547), Impact Resistance >8 N.m EN1517, Shock Absorption 16% - 20% EN14808, Spectular Gloss <30 EN2813, Abrasion resistant (H 18 Wheel) <1000 Mg / 1000 Cycles EN ISO 5470-1. Colour - Blue. including cost, conveyance, loading, unloading of all materials, cost of all labour, sundries, T&P required for the work .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supply & Installation of 6 mm thickness EVA foam called " EVA Foam SOFT". The is specially designed to provide cushioning system over the Concrete Badminton Arena. Suitable for Indooe Use, The mat is Precise, flexible, closed cell Non-Absorbent nature for any kind of liquid & has a smooth Finish. This cushioning System is denser and soft, Ultra light weight, highly formale with high density of 140 Kg/ Cubic Meter with a shore hardnedd of 40 - 45. It has a smooth texture on both sides, is easy to cut, shape & Paste with Adhesive. It is excellent for heat forming and scoring. The cushioning needs to be pasted on the concrete base with Adhesive & Heat Technology before laying the PVC Vinyl Sports Flooring.All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supply & Installation of BWF Certified PVC Badminton Court Mat of 4.5mm thickness for playing area, Size Size 15.4m X 7.1m, EN/DN Tested (EN 14904: Shock Absorption>= 11%,Vertical Deformation or DIN 18032.2:Force Reduction>=11%,Standard Deformation) to be glued /taped on top of the mat, including line marking. The cost includes all materials, labour, conveyance, taxes, loading, unloading, T&P, etc. Complete as per drawing and as per relevant specification including the followings and asper the direction of the Engineer-in-charge.(Mat Colour -Green for Playing area)Must be approved by BWF. complete including cost of all materials, labour T&P etc.All complete of approved quality & specification as per the direction of Engineer -in-charge. (Per Court Mat)

Supply & Installation of 4.5 mm Sports PVC Flooring Mat for Play off Area/ Margin, EN428, Anti Virus, Anti Bacterial Heavy Metal Free, Phthalate Free. Weight 3350 G/Sq. Mtr EN430. Impact Sound Insulation 20 - 22 EN ISO 717-2 & EN ISO 140 - 8, Flammability class CFL - S1 EN13501 - 1, VOC Indoor Air Quality Floorscore Certified ( SCS - FS - 04547), Impact Resistance >8 N.m EN1517, Shock Absorption 16% - 20% EN14808, Spectular Gloss <30 EN2813, Abrasion resistant (H 18 Wheel) <1000 Mg / 1000 Cycles EN ISO 5470-1. Colour - Green.All complete of approved quality & specification as per the direction of Engineer -in-charge.

Preparation of fabrication drawing (shop drawing approved by EIC) and supply, fabrication, erection, testing & commissioning Structural steel (circular/rectangular/square) work welded in built up sections, trusses and framed work both in straight and curve shape including cutting, hoisting, fixing in position and applying 2 coats of zinc chromate anti corrossive primer and 2 coats of synthetic enamel paint of approved shade etc complete as per the approved drawing & design and direction of engineer-in-charge.

Supply and fixing of KALZIP /Equivalent SELF SUPPORTED SECRET FIX STANDING ROOFING SYSTEM IN 0.9mm THICK AA 3004/3005 ALUMINIUM ALLOY. The general roof construction shall comprise from bottom to top:Top layer Kalzip 65/400 Straight/ curved profile sheeting manufactured from aluminum self supported standing seam roof system from aluminum alloy AA 3004/3005 H46 (AlMn1Mg1) as specified in BS EN 1396: 2015 material thickness of 0.9mm and in finish of Pvdf consisting of anticorrosive primer of 5 microns, topcoat of PVDF in 20 plus or minus 2 microns with the Total coating thickness as 25 Microns. The coil for the top panel shall have 75 microns transparent protective guard film with the roofing manufacture name printed, This Guard film prevents scratches during roll forming & handling. The standing seam sheet panel of approved make shall be fixed on to the purlin using aluminum ST clips. The head of clips shall be fixed accurately to ensure the roof sheeting expands and contracts freely during thermal movement. The material properties shall be as follows: Ultimate tensile strength minimum 200N/mm2, 0.2% Proof Stress: min 185 N/mm2, Sheets are to be laid to meet the requirements of the building geometry and fixed on aluminum clips. Clip to be fixed with SS 304 screws only.Second Layer Insulation One layer of Rockwool India / Roxul /Rhino insulation of 50mm thickness minimum 60 kg/m³ density. Sub Girt- Top Hat and top hat bracket as required in 2.0 mm thick and 2mm thick Galvanised steel hat section to be fixed on trapezoidal Liner sheets extra Third Layer Vapour Control Layer Double Sided aluminum foil. Fifth Layer Trapezoidal Sheets Solid 30 to 35 /200 Galvalume steel liner 550 MPa, 0.5mm TCT 1000 mm total cover width 30 to 35mm deep ribs. Purlin Spacing to be advised by the roofing manufacturer and advised at 1200 mm. The panel shall be manufactured out of Hi tensile pre painted Zincalume/Galvalume steel AZ150 (min. 150gms/sq.mt total on both sides) having minimum yield strength of 550 MPa. The finish to the exposed surface of the liner will be polyester coating with film thickness of 15 to 20 m +/- 2 m. The roofing system manufacturer shall submit the below valid. 1. British Board of Agreement Certificate 2. The Institute of Bautechnic Zulassungbeschield N R 14.1 .181. 3. Factory Mutual certificate in India. The rate shall include all accessories for the expansion joint , nut bolts & panels. A qualification criteria includes t manufacturer should have prior experience in execution of stadiums with the specified roofing system in India. The erection / fixing /installation shall be done by specialized / authorized agency as approved by manufacturer. MOQ shall be 2500 Sqmtr for Mobilizing RF machines Aluminum Flashing Flashings manufactured from aluminum alloy AA 3004/3005 (AlMn1Mg1) as specified in BS EN 1396: 2015 material thickness of 0.9 mm & same finish as panel. Flashing girth to be maximum up to 578mm. Gutters -supply and fixing of gutters as per detailed drawings consisting of and aluminum gutter of 2mm in mill finish thickness, fabricated as per the sizes required. Supply and fixing of single skin 2 mm Aluminum gutter, GRADE AA 1100/AA1200 ALLOY with EPDM Expansion joints for every 6.0mtr length, Down take spout of 100- 250 mm at every 10mtr gutter length, & other accessories and welding at joints. The Girth of gutter shall be minimum 1200mm / as advice by the MEP consultant. Feasibility shall be confirmed based on site conditions.All complete of approved quality & specification as per the direction of Engineer in charge.

Supplying, fitting and fixing of M.S window grills made out of ms flats, pipes, square bar etc (as per I.S. specification and as per approved drawings) in proper position in all floors and at all height including making holes to brick walls/ R.C.C structure/wood work etc. and making good to the damaged walls/ structures with cement concrete (1:2:4) with black hard crusher broken granite stone chips of 12mm to 20mm size (20mm size not to exceeds 25% ) including watering and curing etc. complete in all respect as directed by the Engineer in charge.

Supplying, fitting and fixing of MS openable door with 35 x 35 x 6mm size M.S. angle frame as chowkath and 30x30x5mm Ms frame for shutter with 25x6mm flat fabricated to proper size of door opening with 16 gauge CR sheet including fixing clamps for door frames and hinges for fixing shutters and aldrop with tower bolt etc. complete for all floors including cost, conveyance, taxes of all materials, labour, T&P etc.required for the work etc. All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supplying, Fitting and fixing of stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mmx32mmx2mm @ 0.90mtr C/C and stainless square pipe bracing of size 32mmx32mmx2mm in 3 rows in stair case as per approved design and specification buffing polishing etc with cost conveyance taxes of all materials labour T&P etc required for the complete in all respect.All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. 75mm x 50mm.

Supplying and fixing of 46mm thick GI doors and frame conforming to IS 277 galvanized plain skin passed sheets of 0.8 mm in shutter and 1.2 mm in frame with minimum 120 gsm zinc coating with profile dimension of 100mmX58mm. Frame filled with Polyurethane foam and shutter duly filled with Honeycomb and both coated with minimum 60 microns of RAL 8017 PLAIN STEEL WITH OR WITHOUT VISION PANEL finish powder coating. Accessories (hinges/tarbolt/buffer.) will be provided with doors etc complete.(Size of Vision panel 300mm x200mm).All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cubic Meters and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water /moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. 30mm thick

ALUMINIUM SLIDING SYSTEM WINDOW WITH MESH PANEL :- Providing and fixing Anodized System Aluminum Sliding glazed windows suitable for 1.6 KPA wind load with 50mm visible aluminium section width in the centre interlock. The system offered must be ride-in system with two/three glass panels moving inside the channel without any external overhung along with a provision for mesh panel on the third/fourth track. The extruded aluminium sections should be made from Grade 6063-T5 & Anodized with Tex guard coating. Corner connection will be Butt joint with using Nano gaskets for sealing. All other major Accessories should also be made by the same manufacturer. All Slider doors & windows will be centre locking with integrated Anti-lift in slider panel. Only EPDM gaskets should be used in all meeting points instead of Brush Pile. The outer frame Depth will be 72 mm +/- 3 mm The bottom frame must use a subframe and no direct grouting will be permitted on bottom frame directly. All glasses will be 5 mm clear toughened.The system should qualify Airtightness ASTM E283: 10.7m3/h.m2 at 75Pa of pressure, Water tightness ASTM E300: 240 Pa, Wind load resistance ASTM E330: 1600 Pa.All complete of approved quality & specification as per the direction of Engineer -in-charge.3 Track 2 Glass panel 1 Mesh Panel

4 Track 3 Glass panel 1 Mesh Panel

Aluminum Fixed / Top hung Ventilators:Providing and fixing Anodized System Aluminum top hung windows of TOSTEM / NCL ALLURO / ALUMIL make using easy clean hinges with fixed part having cut outs on glass for exhaust provision, suitable for 1.6 KPA wind load. The extruded aluminium sections should be made from Grade 6063- T5 & Anodized with Tex guard coating. Corner connection will be Butt joint with using Nano gaskets for sealing. All other major Accessories should also be made by the same manufacturer.Only EPDM gaskets should be used in all meeting points instead of Brush Pile. The outer frame Depth will be 72 mm +/- 3 mm. All glasses will be 5 mm frosted toughened.The system should qualify Airtightness ASTM E283: 10.7m3/h.m2 at 75Pa of pressure, Water tightness ASTM E300: 240 Pa, Wind load resistance ASTM E330: 1600 Pa. Fixed / Top hung Ventilator

Fixed with exhaust provision / Top hung Ventilator

Top hung Ventilator

DOUBLE LEAF ALUMINUM OPENABLE GLASS DOOR :- Providing and fixing Anodized System Aluminum double leaf openable glass door made of suitable for 1.6 KPA wind load with 50mm visible aluminium section width in the centre interlock. The system offered must be ride-in system with two glass panels moving inside the channel without any external overhung along with a provision for mesh panel on the third track. The extruded aluminium sections should be made from Grade 6063-T5 & Anodized with Tex guard coating. Corner connection will be Butt joint with using Nano gaskets for sealing. All other major Accessories should also be made by the same manufacturer. All Slider doors & windows will be centre locking with integrated Anti-lift in slider panel. Only EPDM gaskets should be used in all meeting points instead of Brush Pile. The outer frame Depth will be 72 mm +/- 3 mm The bottom frame must use a subframe and no direct grouting will be permitted on bottom frame directly. All glasses will be 5 mm clear toughened.The system should qualify Airtightness ASTM E283: 10.7m3/h.m2 at 75Pa of pressure, Water tightness ASTM E300: 240 Pa, Wind load resistance ASTM E330: 1600 Pa.

Aluminum Fixed Curtain Glazing :- Providing and fixing Anodized System Aluminum curtain glazing, suitable for 2.4 KPA wind load. The extruded aluminium sections should be made from Grade 6063-T5 & Anodized with Tex guard coating. Corner connection will be Butt joint with using Nano gaskets for sealing. There shall be no visible joineries in any intermediate section. All other major Accessories should also be made by the same manufacturer. The outer frame Depth will be 100 +/- 5 mm with minimum transom / mullion size of 100 mm x 70 mm or 200 x 70 for height exceeding 3000 mm. All glasses will be 22 mm DGU Ref Toughened ST-146 and to be fixed from outside only.The system should allow glass thickness up to 12 mm. The system should qualify Airtightness ASTM E283: 10.7m3/h.m2 at 75Pa of pressure, Water tightness ASTM E300: 240 Pa, Wind load resistance ASTM E330: 2400 Pa.

Supply and fixing of U Shape Vertical Louver Batten Make profile height 50/100/50 mm , formed out of 0.50mm TCT Galvalume with 50 mm clear gap between two panels acting U shape vertical louvers with Powder Coating on Visible Surfaces of Panels to enhance the building and supporting structure to be coated black color Carrier, 20 mm wide at the bottom x 40 mm deep formed out of 0.60 galvanized steel black Coated with protruding ears to hold the panels in a module of 50 mm centre-to-centre gap. Gi rod 4 mm shall be fixed on Anchor Fastener into the slab at distance to-centre on which will be laid with not more than 1.2 mtr. centre corrosion proof ss clip and on this rigid structure carrier shall be fixed horizontally at distance of 1 mtr. To 1.2 mtr. centre-to-centre. Panel shall be clipped in carriers

Providing & fixing Restroom Cubicle (of approved design which includes 600mm door size width) self-supporting 12mm thick compact laminates made out of, urea free, thermosetting phenolic resins treated Kraft papers as core material and Amino plastic resin treated decor papers on the finish surface, conforming to latest and applicable IS: 2046-1995, EN 438:2016 and NEMA LD3-2005 quality standards with Antivirus, Antibacterial and Antifungal properties (conforming to ISO 21702:2019, JIS Z2801:2010 and ASTM G21-2015 standards respectively) to fulfil the applicable requirements of indoor air quality certifications for Greenguard-Gold standards.This also includes providing and fixing in position necessary hardware made out of Nylon Polyamide grade 6 & Aluminium alloy grade 6063-T6 powder coated finish in black and other available color hardwares as per manufacturers specifications & Architects instructions like (1) Self closing hinges in Nylon Polyamide grade 6 in gloss finish in available colors (2) Soft closing thumb turn lock made in nylon polyamide grade 6 in gloss finish in available colors (3) Single Coat hook in nylon polyamide grade 6 in gloss finish,available in similar available colors (4) U & F- profiles in Aluminium alloy grade 6063-T6 with powder coating in available colors (5) Nylon polyamide grade 6 Adjustable Leg (6) Top rail along with Nylon Polyamide grade 6 with end cap is a Round D shaped extrusion made of Aluminium alloy grade 6063-T6 with Powder Coating in available colors, (7) Rubber, (8) Screws & wall Plugs ( SS- 316 ). The top fitting should consist of Matt finish aluminium alloy grade 6063-T6 in avilable colors, which will get fixed on pilasters with SS Screws, All screws will of 316 Grade in stainless steel . All pilasters are supported by grade- 6 Nylon Polyamide Thermoplastic palm design pedestal footing with non corrosive steel inserts. The base anchored to the floor with grade 316 satin finish stainless steel screws with push fit capping at a clearance height of 150mm. Toilet Cubicle with standard dimension of 1995mm Height x1000- 1200mm Width x 1100-1200mm Depth, which includes 600mm door size width).

Providing 25mm thick grading concrete in C.C. (1:2:2) laid in proper slope over terrace roof slab by using two part of sand, one part of cement and two parts of 6mm size black hard crusher broken granite chips with addition of water proofing compound of approved quality to be mixed with specified ratio including watering, curing, cost, conveyance, royalties, taxes of all materials, cost of all labour, T&P etc. complete as required for the finished item of work as directed by the Engineer-in-charge. Ground Floor

First Floor

Terrace Water Proofing: Cleaning all the surface area to remove loose patrical such as mortar dust etc, with wire bruch and air blower complete in all respect like repairing of crack by polymer modified cementitious mortar as per the direction of Engineering In charge. Providing & Applying two component, cementitious acrylic polymer based high performance waterproofing coating AquaArm 2C-P/Equivalent manufactured and supplied by MYK Arment /Equivalent at a coverage of 0.5 m2/kg in 2 coats at approx 1.2mm DFT. Coverage may vary depending upon the surface. The waterproofing scope shall include supply of geotextile of 120 GSM. polymer modified cementitious mortar as per the direction of Engineering In charge.

Wet area Water Proofing: Providing and applying Single component AquaArm Saniflex/Equivalent synthetic rubber based coating with a coverage of 1.2 kg /m2 over primer surface for 0.8mm DFT in two coats .The coating shall be taken upto 300mm from finished floor level on the vertical walls. The coating shall have an elongation of a minimum of 86% when tested as per ASTM D 412 and tensile strength of 1.05 N/mm2.Thorough surface preparation by mechanical means to level and plain the surface of walls and floors of the toilet areas. All cracks and crevices to filled and made good to receive waterproofing coating treatment The coating shall cover all the floor area of the wet area (toilet) and be applied over on to the vertical walls upto tap point/shower point height above the floor in two or more coats to achieve required thickness.The rate includes coving/ bore packing wherever neccessary. Work shall be carried out by manufacturer's authorised applicator as per manufacturer's methodology.

Finishing inside wall surface with cement based wall putty of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging charges with cost of all materials taxes, labour T & P etc complete as per direction of Engineer-in-charge.Ground Floor

First Floor

Second Floor

Finishing outside wall surface with cement based wall putty of approved make and finished smooth and even surface to receive painting including cost of scaffolding staging charges with cost of all materials taxes, labour T & P etc complete as per direction of Engineer-in-charge. Ground Floor

First Floor

Second Floor

Providing and painting internal surface two coats with plastic emulsion paint over a coat of water based primer of approved quality and approved shade in all floors at all height by making the surface of wall smooth including cost, coveyance, loading and unloading and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by the Engineer in charge. Ground Floor

First Floor

Second Floor

Painting to external surface of building with two coats of weather coat over a coat of water based primer of approved shade and quality of approved design, after cleaning by watering & removing the dirts etc. to the surface to be painted including watering, curing, cost, conveyance and taxes of all materials, cost of all labour, brushes, T&P etc. and necessary scaffolding work complete as directed by the Engineer-in-charge.Ground Floor

First Floor

Second Floor

Providing and painting two coats with synthetic enamel paint over a coat of zinc oxide primer of approved quality and approved shade confirmming to ISI on steel work to give an even shade in all floors at all height including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge. Ground Floor

First Floor

Providing and applying two coats in approved shade on a smooth cement sand plaster. The composition of the texture paint should consist of Acrylic Copolymer Resigns combined with Quartz, Silica,mineral aggregates, synthetic inorganic pigments, bactericide, fungicides and various other additives,giving the product water repellant properties. The first coat to be applied by brush or wool roller as a base coat, diluted with sufficient water and the final coat applied undiluted with trowel and then finished with acrylic trowel to obtain the specified grooves.The thickness of both coats dhould be 1.0 to 1.5 mm. The water repellency of the product is 86gm/m2 as per test method IS: 5410-1969.

Supply & Fixing of Color Coated Galvaleum Metal Sheet of 0.5mmTCT having special polyester colour coating thickness of minimum 20 microns (DFT) on exposed surface and 5 microns (DFT) on unexposed surface over 5 microns (DFT) of polyester primer on both surfaces in CRCA Sheet of 550 MPa , Hot Dip coating of 150 Gms/m2 Aluminium Zinc alloy conforming to ASTM A 792 M-02/ AS 1397 all asper manufacturer's specifications of approved shade to be fixed to MS Structure by using self tapping EPDM based Screws of Hilti/ Fischer/ Buildex or equivalent make on outer Surface, G.I-Z purlin along with required INSULATION in between two sheets and 0.4.mm TCT Bare Galvaleum / GI Color coated Sheet on inner side having standard panel over the MS Structure with all accessories like , End Cap, Flashing and all hardware, silicon sealant, etc. all complete as per direction of Engineer in charge. (Excluding cost of steel)

Supplying, fitting and fixing of M.S decorative grill gate made out of ms flats, pipes, square bar etc including brass mouldings (as per I.S. specification and as per approved drawings) in proper position in all floors and at all height including making holes to brick walls/ R.C.C structure/wood work etc. and making good to the damaged walls/ structures with cement concrete (1:2:4) with black hard crusher broken granite stone chips of 12mm to 20mm size (20mm size not to exceeds 25% ) including watering and curing etc. complete in all respect as directed by the Engineer in charge.

Providing and laying cement concrete 1:2:4 on walls (any thickness), including the cost of centering, shuttering and finishing :including cost of all materials, conveyance, loading and unloading, all taxes and royalties, all labour, scaffolding, watering and curing, sundries and T&P etc. complete as per direction of the Engineer -in-charge

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre.

Construction, Providing , Supplying and fixing the pre cast , pre tensioned SFRC compound wall poles having finished dimention of 200mm x 200mm x 300mm long, (providing the construction joint at the interval of 15.4 mtr) made in M-30 grade concrete with 10 Numbers of 4mm dea. HTPC ( High Tension Pre Coated) wire, fixed in cast in situ PCC m-20 concrete in foundation footing of size 600 mm dia 750 mm depth from top inside the pre-cast RCC collar ( NP 2) of 600 mm Internal dia. & length of 750 mm placed over a base of PCC (1:4:8) of size 680mm dia, 100 mm depth including excavating foundation pit for each pole, kind of soil of size 680mm dia, 850mm depth ( at expansion joint of 15.4 m interval where combined poles are to be places with 900mm internal dia of NP 2 collar of 750mm height) including watering & curing for required days along with supplying, fitting & fixing of precast, pre tensioned, SFRC slab having dimention of 2100mm (long) x 300mm (Wide)x 500 ( thick) 7.5 Numbers. per span, made with M 30 grade concrete with 4mm dia. GI HTPC wire 4 Numbers. covering the top of the compound wall poles with a pre-cast SFRC cover of size ( 300x300x150) mm in order the prevent the slab panels from removing . all complete as a set to be measured in term of running meter including such pre cast, SFRC top cover, slab, pole, including painting two coats of approved weather coat paint over a coat of wall primer including curing cost and conveyance of all materials, royalties, taxes all labour, labour cess, T&P required for the work etc. complete including dewatering if required as per the direction of the Engineer in Charge(Excluding cost of GST)

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000x450x50mm, reinforced with 8mm dia four Numbers longitudinal & 9 Numbers cross sectional T.M.T hoop bars, including providing 50mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50mmx1.6 mm complete, all as per direction of Engineer-in-charge.

Excavation in all kinds of soil with hydraulic excavator (1 Cubic Meters capacity) including cutting and loading in tippers, trimming bottom and side slopes ,in accordance with requirements of lines,grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m.

Rolling & compacting to sub grade or formation loosening by cutting earth for 15cm below the sub grade including watering and compacting in layers by PRR, cost & conveyance of required quantity of water, cost of all labour sundries, T & P etc. required for the work to complete in all respect as per specification and direction of Engineer-in-charge.

Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (5th Revision) etc complete as per direction of Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in subbase/base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per Clause 406 of MoSRT&H Specifications for Road & Bridge works

Providing and laying 80mm thick factory made cement concrete interlocking paver block of M-40 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Supplying and fixing of precast kerb stone of size 600mm x 300mm x 150mm of M-30 grade of approved make, design, colour and size made by Block making machine with proper compaction fixed in required pattern etc. complete in all respect conforming to IS 5758:1984

Providing and painting two coats with synthetic enamel paint over a coat of zinc oxide primer of approved quality and approved shade confirmming to ISI on brick/rcc work to give an even shade in all floors at all height including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge.

Supplying and filling with river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for complete the work as per direction of the Engineer-in-charge.

Earthwork excavation of any approved type of soil in approved borrow area by mechanical means loading into transportation by mechanical means and unloading the soil within 5km lead on properly prepared . including spreading and leveling the earth in 22.5cm layers to make ready for watering and compaction with rollers and dozer etc.including all cost of labour , conveyance, royalties and taxes ,sundries ,T & P etc.complete as per the directions of Engineer-in-charge.

Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction.

Supply and Laying of geo synthetic texile @ 200 GSM .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing, laying, spreading and compacting graded stone aggregate to laying in uniform layers in subbase/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density etc.including cost of all labour,material,conveyance,loading and unloading,machinery charges all complete as per the direction of Engineer-in-charge.

Supplying , stacking and spreading of good earth at site within initial lead including royalty and carriagetransporting to site, spreading, grading to required slope and compacting to meet requirement.

Supplying , stacking and spreading of root zone sand as per USGA standard at site including royalty and carriage and Laying of root zone sand on the top of aggragate as per desired level

Supply and laying of labour and material for Base preparation of grassing and fertilizer apllication in the required proportion specified or directed by the Officer-in-charge.

Supply & Planting Bermuda grass on site by Planting method directed by engineer in charge. The grass must be weed fee. Rate including all required fertilizer, pesticider & Chemical etc. complete for growing the turf. Spec. No.:- As directed by Engineer in charge. (Including cost of 6 month of Maintenance of football Ground)

Providing and laying of hot applied thermoplastic paint 2.5 mm thick including reflectorising glass beads @ 250 gms per Square Meters area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Supplying, stacking, laying and compaction of a consolidated layer, 50 mm thick, of graded material of 4.75 mm to 2.36 mm mixed with cohesive material for stability and grip, etc., as per the direction of the engineer-in-charge.

Construction of cement concrete kerb with channel with top and bottom width 115mm and 165mm respectively 250mm high in M20 grade P.C.C on M15 grade foundation 150mm thick kerb channel 300mm wide 50mm thick ,slope towars the kerb ,kerb stone with channel laid with kerb laying machine ,foundation concrete laid in manually ,all complete .

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of land manure before and after flooding trench with water (excluding the cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site (Earth measured in stacks will be reduced by 20% for payment) with all lead and lift.

Supplying and stacking sludge at site (sludge measured in stacks will be reduced by 8% for payment) with all lead and lift.

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) . Screened through sieve of I.S. designation 20 mm

Screened through sieve of I.S. designation 16 mm

Screened through sieve of I.S. designation 4.75 mm

Rough Dressing the trenched ground including breaking clods etc.all complete as per the direction of Engineer-in-charge.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 60 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (The manure/sludge shall be paid for separately).

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 60 cm dia, and 60 cm deep

Holes 45 cm dia, and 45 cm deep

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Numbers ( 3 Numbers horizontal & 4 Numbers vertical U shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge.Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm

Filling of the following size empty pots with mixture of good earth & manure in the ratio of 2:1 (Two part of Good earth & one port of manure) and placing them on appropriate place i/c carriage of earth, manure and pots up to 50 mtr, as per direction of officer incharge. (The cost of good earth, earthen pots & manure will be paid separately.) Size of Empty Pots 35cm Top dia, 25cm Bottom Dia & 35cm Perpendicular height.

Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per Square Meters lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site incharge watering and removal of unserveiceable materials as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Shrubs Plant

Hedge Plant

Providing and displaying of Aglaonema dove variety Plant, having ht. 30 cm to 45 cm with 8 to 10 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema Snow-White hybrid plant (three in one), having ht. 30 cm & above with 6 to 8 leaves, bright colour, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot . (Specimen Plant) & as per direction of the officer-in-charge.

Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Croton Challanger variety plant, having ht. 30cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Croton Baby Golden plant (three in one), having ht. 30cm, multi branches, well developed with fresh and healthy foliage in 25 cm size of Earthen pot / Plastic pot. as per direction of the officer-incharge.

Providing and displaying of Dracaena Song of India plant (three in one), having ht. 30 cm and above, multibranched, well developed with fresh and healthy leaves in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Money Plant Broad Leaves mounted on moss stick 90 cm ht., 3 to 4 plants in each pot, well developed with full of fresh & healthy leaves in size of 25 cm Top dia x 18 cm Bottom dia x 25 cm Perpendicular height Earthen pot / Plastic pot . & as per direction of the officer-in-charge.

Providing and displaying of Phoenix palm plant, having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying plants Cladium Hybrid variety 3 to 4 plants in a pot well developed with fresh & healthy foliage 30 to 45 cm ht. in different colour 25 cm Earthen Pot/Plastic Pot and as per direction of the officer incharge.

Providing and Displaying plants Cosmos well developed fresh & healthy 20 to 25 cm ht. attractive colours multi branching at blooming stage in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying Acalypha green plant well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge.

Providing and Displaying Bamboo Buddha vally variety with umbrella shape plant having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy plant as per direction of the officer-in-charge.

Providing and fixing overhead type sprinkler system with self closing valve type 25mm X 20mm with self closing spring made up of alluminium alloy and brass fittings including cost of all materials, labour, T & P etc complete as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fixing 15mm dia CP Bib cock of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labours, T&P and fitting and fixing of the 20mm dia CPVC pipe confirming to IS 15778 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance and taxes of all materials all complete as per PH specification and direction of Engineer-in-charge.

provision of mentainance of the above landscaping work first year - @10%

Second Year @7.5%

Third Year @ 5%

Providing weep holes in Brick masonry /Plain/Reinforced concrete abutment,wing wall return wall with 100 mm dia PVC pipe,extendeding through the full width of the structure with slope 1V:20H towards drawing face,complete as per the drawing and direction of Engineer-in-charge.The cost inclusive of all material,pipe,fitting cost of all labour etc all complete.

Supply & Installation of AIFF/FIFA Compliant Portable & Movable Football Goal Post , Size 7.32 M X 2.44 M Inner to Inner, With 8 Inch Non Marking solid Galvanised Wheels for smooth movement, Main pipe made of 100mm Round Powder Coated High Grade Aluminium Alloy Pipe of 3mm thickness, Back Support made of 60mm Round Powder Coated High Grade Aluminium Alloy Pipe of 2.5 mm thickness, No sharp edges, All corners fully welded and ground smooth, 220 Pcs Polyproplene unbreakable net clips no sharp edges, including transportation, Installation, testing & commissioning as per Engineer-In-Charge .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supply & Installation of FIVB Compliant Portable & Movable telescopic Volleyball Post, Made of heavy duty 100mm round Aluminium Alloy Pipe with crank system for height adjustment 2.43 m for mens & 2.24m for womens, With 120kgs Weight Stacks for stability. Steel pulley on top, including transportation, Installation, testing & commissioning as per Engineer-In-Charge .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supply & Installation of Kho Kho Pole,Two rigid poles of 1.20 m height from ground level, Heavy Duty 4 inch Dia Smooth & Round Steel Uprights, No sharp edges to prevent injury

Supply & Installation of TTFI/ITTF Certified Table Tennis Table, Size 274cm X 152.5cm X 76cm, 25mm Top to ensure consistent bounce & optimal Spin Performance. 25 X 50 mm Heavy-duty alloy steel frame for superior durability and strength. Smooth, Axalta Polyurethane Anti-Glare top Finish for clear visibility and accurate play. Top Colour Black. Must have 100 mm eight wheels for easy mobility, with four being lockable for added stability. Premium Professional T T Tables with Foldable Design. N. W. / G. W. - 116 Kgs / 123 Kgs, including transportation, Installation, testing & commissioning as per Engineer-In Charge .All complete of approved quality & specification as per the direction of Engineer -in-charge.

Supply & Installation of BWF Certified Movable Badminton Post With 80 Kg Cast Iron Base for stability, 75 mm Nylon Wheels & Anti Stick PU Rubber Sheet Inside Base and Weights. 95x46mm Square Steel Pipe Connecting the Base & Uprights. 39mm Round Uprights of 4mm thickness. Uprights Height Must be 1.55 Mtr. Stainless Steel Pully Strong System. Powder Coated Rustproof.All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing, supplying Nyon BADMINTON NET With 4 side tape (Tournament Quality) of approved quality, size as per specificationand direction of Engineer-In-Charge Must be Approved by - BWF.All complete of approved quality & specification as per the direction of Engineer -in-charge.

Providing, supplying Badminton racket of approved quality, size as per specification and direction of Engineer-In-Charge.

Providing, supplying Nylon Shuttle Cock Tournament approved quality, size as per specificationand direction of Engineer-In-Charge. (PACK OF 6 Numbers)

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).

Providing Retro-reflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.

Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge.

Providing and fixing letters made out of acrylic sheet with light arrangement as per the architectural drawing/design complete with all materials cost, coveyance, loading and unloading, royalties and cost of all labour, T&P, sundries, with necessary scafolding & accessories complete in all respects as per the direction of architect / engineer in charge. 750mm height

300mm height

Plastic Waste bin Rectangular alongwith fabricated MS stand with one coat of primer and two coats of enamel paint for stand. MS stand should be grouted properly on the ground level. Capacity-60 350x350 mm Top Dia.250x250 mm Bottom Dia.850 mm Height pair Sintex, Nilkamal, Otto, Aristo

Plastic Waste bin without Wheel with Push type Top load along with fabricated MS stand with one coat of primer and two coats of enamel paint for stand. MS stand should be grouted properly on the ground level capacity 60 pair 350x350 mm Top Dia. 250x250 mm Bottom Dia. 850 mm Height Sintex, Nilkamal, Otto, Aristo

Plastic Waste bin without Wheel with Swing lid type Top load along with fabricated MS stand with one coat of primer and two coats of enamel paint for stand. MS stand should be grouted properly on the ground level. Capacity-60 pair 350x350 mm Top Dia. 250x250 mm Bottom Dia. 850 mm Height Sintex, Nilkamal, Otto, Aristo

PH WORK Supplying all materials, labours, T&P for fitting and fixing white glazed vitreous china floor mounted European coupled water closet of Jaquar make having cat no CNS-WHT-755S220SPPZ or equivalent type of approved make including supply of matching P/S trap to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete including cost of WC pan, PVC seat cover with CP brass hinges and rubber buffers etc all complete including cost, taxes and conveyance as per specification including polishing etc all complete as per PH specification and direction of Engineer-in-charge.

Supplying all material, labour T&P and fixtures for providing and fixing of white glazed vitreous chinaware under counter wash hand basin of approved size of Jaquar make having cat no CNS-WHT-705 or equivalent type of approved make with bottle trap of Jaquar cat no ALD 769L250x190 with CP waste coupling nut of Jaquar make having cat no ALD 709 and 15mm x 450mm PVC connection pipe of Jaquar make having cat no ALD 803AB with MS bracket with wooden plugs CP screws including cost of cement, sand, labour, T&P etc. complete including testing cost, conveyance, royalty and taxes of all materials etc. complete as per PH specification and direction of Engineer-in-charge.

Supplying and fixing urinal of Jaquar make having cat no URS-WHT-13261H or equivalent type of approved make including all fittings like 450mm long connection pipe of Jaquar make having cat no ALD 803B, waste pipe etc of approved make etc complete as per PH specification and direction of the Engineer-in-charge.

Providing and Fixing of Urinal Partitions made of 12 mm thick Compact Laminates having total height of 1195 mm and depth of 450 mm with SS 316 grade L clamp and scews for fixing..

Supplying all materials, labour, T&P and fixing standard sized 15mm dia Angular Stop cock of Jaquar Cat. No.-FLP 5053PM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized 15mm dia pillar cock of Jaquar Cat. No.-FLP 5011PM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing two way Bib cock of Jaquar Cat. No.-FLP 5041N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing health faucet of Jaquar Cat. No.-ALD 563 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized CP towel rail - 24" of Jaquar Cat. No.-ACN-1111SM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized CP towel ring square of Jaquar Cat. No.-ACN-1121N or equivalent etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized liquid soap dispenser of Jaquar Cat. No.-ACN 1135N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Providing and fixing C.P. Glass shelf 600mm long of Jaquar Cat. No.-ACN-1171N or equivalent type of approved make fixed to wall including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized CP toilet paper holder of Jaquar cat. No.-ACN1153S or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized CP robe hook of Jaquar Cat. No.-ACN 1191N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Providing all materials, labour,T&P and fittings and fixing of urinal valve auto closing system with built in control cock Jaquar Cat. No.-PRS 077 or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labor T&P for fitting and fixing in all floors' fixed type glass mirror of size 600mm x 450mm best INDIAN make of 5.5 mm thickness with supply of 13mm thick asbestos backing and wooden plugs C. P. Brass screw including cost, conveyance, royalty, taxes of all materials complete as per P.H. specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized Wall Mixer of Jaquar Cat. No.-FLP 5273PM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing of round shape CP overhead shower of Jaquar Cat. No.-OHS 1789 with arm SHA 477 or equivalent etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all materials, labour, T&P and fixing standard sized CP Soap case of Jaquar Cat. No.-ACN-1131N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Supplying all material, labour T&P and fixtures for providing and fixing of stain less steel sink with drainboard of Nirali Grace plain 610x510mm or equivalent type of approved make with its components like 32mm CP waste of cat no ALD 705, 40mm waste pipe etc, including all requisite fixing materials complete as per the PH specification and direction of Engineer-in-charge

Supplying all material, labour T&P and fixtures for providing and fixing of stain less steel sink with drainboard of Nirali Elegance 1045x510mm or equivalent type of approved make with its components like 32mm CP waste of cat no ALD 705, 40mm waste pipe etc, including all requisite fixing materials complete as per the PH specification and direction of Engineer-in-charge

Supplying all materials, labour, T&P and fixing standard sized sink cock of Jaquar Cat. No.-FLP 5347PM or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge.

Providing and fixing 6L step can in stainless steel etc complete as per PH specification and direction of the engineer in charge

Providing and fixing fragrance disperser etc complete as per PH specification and direction of the engineer in charge

Providing and fixing Floor drain in polished chrome with hole for floor/nahani trap etc complete as per PH specification and direction of the engineer in charge

Providing and fixing circular type stainless steel grating with hole for floor /nahani trap etc complete as per PH specification and direction of the engineer in charge

Supply all materials, labour, T&P and providing fitting & fixing (Aqua guard) pure Chill 80 PSS UV of size 750x570x1350 mm height with water storage capacity 120 liters along with 2 nos of fancets 1 for cold water and 1 for normal water including a flow of 1.5 ltr per minute etc. all complete as per approved drawing, specification and direction of the EIC.

Supplying all materials, labours, T&P and fitting and fixing of the following size of CPVC pipe SDR11 confirming to IS 15778 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance and taxes of all materials all complete as per PH specification and direction of Engineer-in-charge. (Concealed) (15 mm dia )

20 mm dia

25 mm dia

32 mm dia

Supplying all materials, labours, T&P and fitting and fixing of the following size of UPVC pipe S-80 confirming to IS 13592 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance of all materials all complete as per PH specification and direction of Engineer-in-charge.(Non Concealed) (40mm dia)

50mm dia

Supplying all materials, labour, T&P, fitting and fixing UPVC SWR pipes & fittings of approved make confirming to IS-13592, both below and above ground level / floor and on walls including supply of bobbins, nains, screws, wooden cleats, pipe clips as per requirement, including earth work in excavation and fitting, including cuting walls and floor and making good the damages with cement concrete (1:2:4) with hard granite chips, incluidng scaffolding wherever necessary all complete as per the PH specification and direction of the Engineer-in-charge. (75mm dia)

110mm dia

Supplying all materials, labour, T&P, fitting and fixing of UPVC SWR fittings of approved make with requisite testing etc complete as per PH specification and direction of Engineer-in-charge. (110mm dia Single Junction with door)

110mm dia Double Junction with door

110mm dia Cowl

110mm dia Plain Bend

110mm dia SWR Door Bend

125mm x 110mm Gulley Trap

110mm dia Tee with door

110mm dia Single Junction without door

110mm dia Socket plug

110mm dia Pipe clip

110mm dia Coupler

75mm dia Plain Bend

Supplying all materials, labour, T&P, fitting & fixing of different size UPVC Ball Valve of approved make including supply of all necessary jointing materials such as red lead paint, yarns etc. including cost, conveyance of all materials, T&P etc. all complete as per P.H. specification and direction of the Engineer-in-charge. (25mm Dia)

32mm Dia

40mm Dia

50mm Dia

Supplying all materials, labour, T&P and fitting and fixing of UPVC NRV valve of 50mm Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing of double air valve of 50mm Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge.

Supplying all materials,labours,T&P for cutting holes through existing brickwork including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/PVC pipes and fittings etc all complete as per PH specification and direction of Engineer-in-charge.

Supplying all materials,labours,T&P for cutting holes through existing RCC floors & roofs including making good the damages for taking GI pipes and fittings/PVC pipes and fittings etc all complete as per PH specification and direction of Engineer-in-charge.

Supplying all materials,labours,T&P for cutting grooves in pucca floors and walls for taking GI/PVC pipes and making good the damages as per direction of Engineer-in-charge.

Supplying all materials,labours,T&P for cutting holes through existing brickwork including making good the damages in cement mortar (1:4) for taking SWR/HCI pipes and fittings/PVC pipes and fittings etc all complete as per PH specification and direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fittings and fixing of 2000 ltr capasity Poly Propelene white double layer water storage Tank of approved make confirming to IS 12701-1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc including hoisting upto terrace level and placing the tank to the required position etc all complete as per PH specification and direction of Engineer-in-charge. (To provided with brick masonary guard walls which will be paid separately)

Supplyng all materials, labour, T&P for construction of brick masonary Gulley trap chamber of size 250mm x 250 mm with CI gulley trap, by flyash brick masonry in CM (1:4), CP (1:3) with 150mm x 150mm CI grating including labour and materials for fitting and fixing 100mm dia square mouth UPVC gully trap with supply of all jointing materials and encasing the gully trap with a block of CC (1:3:6) with 20mm & 10mm size hard stone metal all complete with providing and fixing of 250mm x 250mm precast RCC cover slab including cost, conveyance, taxes of all materials to site complete as per the PH specification and direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fixing grab bar of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. (Grab Bar Vertical swing,white (JAQUAR -WAC-WHT-860800/ Equivalent))

Grab Bar 692 mm long,white (JAQUAR -WAC-WHT-BR0600/ Equivalent)

Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/ P.V.C/ M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well).

Supplying 200mm polyvinyl chloride pipes as per ASTM-D-1785-89 schedule 80 having threads in accordance with DIN 2999 part-1/DIN-42225 part-II specification length of pipe (laying length) will be 3 mtrs. The pipes shall be supplied with both external and internal threaded with free socket. The pipe having external thread at one end i.e female and or belled end. The female end having internal thread is to be belled in order to accept the male end while jointing pipes,pipes shall be provided with a groove at the male thread to accomodate flexible PVC/Rubber 'O' ring to make the joint water tight colour of the pipe shall be blue. The name of the manufacture along with batch No class of pipe shall be stranded legibly of each pipe length.

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials.

Supplying all materials, labour, T&P and providing and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5m below ground level (as per drawing) to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock at the bottom to ensure sanitary sealing (excluding cost of cement which will be supplied directly by the department)

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge

Supplying all materials, labours, T&P and fitting and fixing of the 80mm dia of UPVC pipe (Sch-80) confirming to ASTM D1785 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance of all materials all complete as per PH specification and direction of Engineer-in-charge.(Non Concealed)

Supply, installation, testing and commisioning of vertical submerssible pump set of approved make having discharge 20m3 per hour and 60mtr head including installation of pump set with wire ropes, clamps etc inside the borewell, etc complete as per the Direction of Engineer-in-charge. (Duty of pump to be decided depending upon yeild of the borewell)

Protection to the Borewell with CC base

3 core 6.0Square Metersm copper flat cable

Bore Cap

Clamp

Earthwork in excavation upto 1.50mtr depth of trench in all kinds of soil including ordinary soil, hard/gravelly soil and stony earth mixed with stone and boulders etc but not requiring blasting with initial leads and lifts including dressing and leveling the bed sides up to required depth and depositing the excavated materials at places away from the work site with T&P for shoring, shuttering, dewatering if required etc. complete as per the drawing, design including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge.

Extra lift of 1.5m or part there of over the initial lift of 1.5m in all kinds of embankments and road works and ordinary earth work in general.

Filling trenches with excavated earth (excluding rock) including laying the earth in layers not exceeding 23.5cm thick ramming and watering with all leads and lifts including cost of all labour, T&P etc. complete as directed by the Engineer-in-charge.

Supplying and filling the trench with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for complete the work as per direction of the Engineer-in-charge.

Providing & laying cement concrete of prop. (1:3:6) in trench using 40mm nominal size down graded, screened, washed hard black crusher broken granite metal of approved quality & from approved quarry including laying in the layers not exceeding 100 mm thick, hoisting, lowering, laying, watering and curing etc. complete to the required levels including cost, conveyance, royalty and taxes of all materials, cost of all labour, T&P etc. as required for complete the work as per direction of Engineer-in-charge.

Providing, lifting, hoisting and laying Reinforced cement concrete work of M-25 grade having minimum compressive strength of 250kg./cm2 in 15cm cubes at 28 days and in accordance with I.S. 456 and I.S. 516 using crusher broken hard black granite chips of approved quality & from approved quarry including laying and compacting concrete with vibrator, watering and curing for 28 days, cost of rigid and smooth centering & shuttering and finishing to exposed surface smooth providing, grooves or beads wherever necessary including cost, conveyance, royalties & taxes of all materials and cost of all labour, T&P etc. as required for complete the work in all respects as per drawing, design and direction of Engineer-in-charge. (But excluding cost of M.S. rod/Tor steel and binding wires and labour charges for bending, binding and tying the grills.)Foundation

Beam & Column

Roof Slab

Providing & fixing TOR Fe-500 D grade reinforcement bars of approved makes for RCC work of required diameter with straightening, cutting, bending, binding welding and joining (if necessary) and tying the grills and placing in position as required for R.C.C. work and providing fan hooks, hoisting, lowering and laying including cost, conveyance and taxes of tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all heights as per the drawing, design and direction of Engineer-in-charge. (Linear measurements will be taken & quantity will be calculated on standard weight. Weight of binding wire will not be considered for measurement.)Ground Floor

Providing 12mm. thick cement plaster with cement mortar of mix (1:4) in all floors with Portland slag cement (PSC) and with screened and washed sharp sand for mortar with neat cement punning finished smooth to brick/RCC walls after racking out the joints including watering and curing complete with cost, conveyance, loading and unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P, scaffolding required for the work etc. complete in all respect as per the direction of Engineer-in-Charge.

Providing 12mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to inside smooth surface of brick masonry walls after scraping, cleaning and racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge. Ground Floor

Providing and painting two coats of cement paint over a coat of cement wash of approved quality and approved shade in all floors at all height including required admixture by making the surface to the internal plastered surface of wall smooth including cost, coveyance, loading and unloading and taxes of all materials, cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by the Engineer in charge.

Providing 25mm thick grading concrete in C.C. (1:2:2) laid in proper slope over terrace roof slab by using two part of sand, one part of cement and two parts of 6mm size black hard crusher broken granite chips with addition of water proofing compound of approved quality to be mixed with specified ratio including watering, curing, cost, conveyance, royalties, taxes of all materials, cost of all labour, T&P etc. complete as required for the finished item of work as directed by the Engineer-in-charge.

Water Tank Water Proofing: Providing and applying Single component AquaArm Saniflex/Equivalent synthetic rubber based coating with a coverage of 1.2 kg /m2 over primer surface for 0.8mm DFT in two coats .The coating shall be taken upto 300mm from finished floor level on the vertical walls. The coating shall have an elongation of a minimum of 86% when tested as per ASTM D 412 and tensile strength of 1.05 N/mm2.Thorough surface preparation by mechanical means to level and plain the surface of walls and floors of the toilet areas. All cracks and crevices to filled and made good to receive waterproofing coating treatment The coating shall cover all the floor area of the wet area (toilet) and be applied over on to the vertical walls upto tap point/shower point height above the floor in two or more coats to achieve required thickness.The rate includes coving/ bore packing wherever neccessary. Work shall be carried out by manufacturer's authorised applicator as per manufacturer's methodology.

Supplying and fixing 900mm dia SFRC cover without frame for manhole including cost of all materials, T&P, labour etc complete as per direction of Engineer-in-charge.

Supplying and fixing stainless steel ladder of approved gauge of 4.0 mtr long and required width inside under ground tank including cost of all materials, labour, T&P etc complete as per approved drawing, design and direction of Engineer-in-charge.

Supplying all materials, labour, T&P for fitting and fixing of water level indicator made of MS flats and plates with lablling etc complete as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P for fitting and fixing of 100mm dia CI/MS/DI overflow line of approved make etc complete as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P for fitting and fixing of puddle collar of 150mm dia of approved make etc complete as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P for fitting and fixing of 100mm vent pipe of approved make etc complete as per direction of Engineer-in-charge.

Supplying all labour, T&P for the Carriage of excavated earth by mechanical means of transport within 5.00 K.M. lead including hire and running charges of vehicles, labour charges for loading and unloading as required for the work etc. complete as per the direction of the Engineer-in-charge.

Supplying all materials, labours, T&P and fitting and fixing of the following size of CPVC pipe SDR11 confirming to IS 15778 certification mark with socket and screw joints in walls and floors including supplying of required number of fittings of approved make including cutting threads to pipes and pipes to length, including wastage,etc for fitting to the walls with supply of holder ats, clamps, fixing wooden plugs in walls, including testing of pipe line for water tightness complete as per IS specification including cost, conveyance and taxes of all materials all complete as per PH specification and direction of Engineer-in-charge. (Concealed) (65mm Dia)

80mm Dia

Supplying all materials, labour, T&P, fitting & fixing of different size UPVC Ball Valve of approved make including supply of all necessary jointing materials such as red lead paint, yarns etc. including cost, conveyance of all materials, T&P etc. all complete as per P.H. specification and direction of the Engineer-in-charge. (65mm Dia)

80mm Dia

Supplying all materials, labour, T&P and fitting and fixing of CI/DI gate valve of following Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge. (65mm Dia)

80mm Dia

Supplying all materials & labour, T&P and constructing brick masonary chamber for water sluice valve, single air valve & non return valve with flyash brick masonary in cement mortar (1:4) as per approved drawing and specification CC (1:4:8) with 4cm size hard granite metal on the bed, 12mm cement plaster (1:3) to inside and cement flush pointing (1:3) to outside surface with 100mm thick RCC M25 cover slab with 12mm hg chips using required quantity of tor steel, centring and shuttering to the slab and dismantling it after 31 days of casting, filling the outside cavity with excavated materials, watering, curing including cost, conveyance, taxes of all materials, labour charges for cutting, bending, binding and tying the grills in proper position etc all complete as per drawing, design and direction of Engineer-in-charge. (Sluice Valve Chamber (0.75x0.75x1.20mtr)

Providing & fixing of following dia CI/DI body non return valve of approved make with high tensile bress rising stem suitable for the system pressure as per IS 780 (65mm Dia)

80mm Dia

Supplying all materials, labour, T&P, fitting & fixing of different size bourden type pressure gauge of reputed make (0-10 kg/sqcm) with valves, piping, fitting of approved make including supply of all necessary jointing materials such as red lead paint, yarns etc. including cost, conveyance & taxes of all materials, T&P etc. all complete as per P.H. specification and as per the direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing of double air valve confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing of CI/DI foot valve of following Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge. (65mm Dia)

80mm Dia

Supply, installation, testing and commisioning of horizontal centrifugal pump set of approved make having discharge 16.5m3 per hour and 35-40mtr head including installation of pump set (5 HP) with suitable base plate and foundation inside the sump, delivery arrangement with suitable GI or MS pipe providing valves fittings etc and connection within 10mtr distance etc complete as per the Direction of Engineer-in-charge. (1W + 1S)

Brick work in foundation and plinth with flyash bricks of size 25cmx12cmx8cm in cement mortar (1:6) with best quality bricks having crushing strength not less than 75 Kg/cm2 immersing the bricks in water for not less than 6 hours before use (the bricks shall be free from cracks, well shaped, uniform in size and shall produce a clear metallic ringing sound when struck) includes molding, chamfering, corbelling .complete as per drawing, design and specification, watering and curing for 7days including cost, conveyance, royalty and taxes of all materials, labour, T&P etc. and as per direction of Engineer-in-charge.

Supplying and fixing 900mm dia SFRC cover without frame for manhole including cost of all materials, T&P, labour etc complete as per direction of Engineer-in-charge.

Supplying, fitting & fixing of MS grill to be fixed into the walls etc. made as per approved drawing etc. complete for all floors as per approved drawing and design, cutting to required size and welding properly, finished smooth and sand papering, painting one coat with red oxide primer, including cost, conveyance, taxes of all materials, T&P etc. as required for the work complete as per direction of the Engineer-in-charge. (Weight certificate way measurement will be produce at the time of bill)

Gravel(Quartz) filling to the filtration chamber with good quality gravel, mixing with water to make it to a plastic state and proper backing as per correct profile including cost conveyance royalty and other taxes of materials with all labour T&P materials required for the item complete as directed by the Engineer-in-charge.

Supplying all materials, labour, T&P, fitting and laying in trenches UPVC pipes & fittings of approved make confirming to IS-4985 and specials of the following outside diameter and classes including jointing with supply of approved solvent cement by non heat application method including testing etc complete as per the PH specification and direction of the Engineer-in-charge. (Earthwork to be measured separately) (100mm dia)

150mm dia

200mm dia

Providing and laying in trench cement concrete ( 1:3:6 ) with 40mm size hard granite metal in the following type of bedding for pvc pipes of the following internal diameter including curing complete as per specification (100mm dia)

150mm dia

200mm dia

Supplying all materials, labour, T&P and necessary materials towards laying of 250mm dia RCC NP2 Hume pipe push tight joint type (including cost of RCC Hume pipe) over PCC bed with plastic rope without damage to the pipe with all convenience the materials to site and including all taxes all complete as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing of PP flanzed end ball valve of 150mm Dia confirming to the relevant IS specification and dimension including fixing it in position along the pipeline with supply of all required materials such as rubber insertion, nuts & bolts including cost of all materials, taxes, and duties, transportation charges from store to site etc all complete as per the direction of Engineer-in-charge.

Providing and placing in position RCC ring of following dia below ground level including jointing the rings with cement mortar 1:4 for rain water silting chamber including cost of all materials, labours, T&P etc complete as per direction of Engineer-in-charge. (900mm Dia)

1200mm Dia

Supplying and fixing RAINY 100mm size MECHANICAL FILTER with auto clean screen and bypass valve as IFC -1 etc complete as per direction of Engineer-in-charge.

Supplying and fixing 200 mm dia FRP Filter Screen with epoxy resin base for dry bore upto 20 mtrs (1 mtr@2500 ) nos- ARC or equivalent etc complete as per direction of Engineer-in-charge.

Labour for drilling a perfectly vertical bore hole for a specified dia for a specified depth below G.L through consolidated and un-consolidated rocks with down the hole hammer drilling rig or combination drilling rig (1200 cfm/ 300 psi) as required to suit the site condition as per the direction of EIC including use of own rigs with its accessories, T&P & consumables etc. for lowering of 200mm dia PVC/GI pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (GI/ PVC casing pipes, if required to prevent collapse of over burden is to be provided by the contractor including lowering and withdrawing after completion of the Tube Well). Labour for drilling of 200mm dia & 150mm dia bore from '0' mtr. to '100' mtr.

Providing & lowering the following size PVC pipes (ASTM) with or without slotted pipes as per the necessity from 1.00m above ground level up to required depth and fitting and fixing up in perfectly vertical position, including cutting, threading pipe and slotted pipe and supplying and fixing all jointing materials, T&P etc. complete and keeping the top of the casing pipe threaded including plugging the tube well to prevent entry of foreign materials from above. The cost inclusive of pipes, fittings, labour, consumables, POL, consumables with hire & running charges of machinaries etc. as per specification & direction of EIC. Lowering of 200mm (8'') dia PVC plastic pipes Sch-80 as per ASTM-D-1785/2004 upto required depth.

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials.

Supplying all materials,labours,T&P for constructing inspection chamber of 900mmx800mmx450mm with cement concrete (1:3:6) on bed with hard granite metal size 40mm and flyash brickwork in cement mortar (1:4) in foundation and plinth, 100mm thick RCC M25 cover slab with supplying fitting and fixing of medium duty SFRC manhole cover, moulding and shaping the channel and benching with cement concrete (1:2:4) using 12mm size hg chips,12mm thick cement plaster in cement mortar (1:3) with punning to inside, cement plaster in CM (1:3) to outside the chamber including centring, shuttering, providing required quantity of MS rods and binding wires for reinforcement, bending, binding, tying the grills and placing in the proper position and drawing and design and PH specification including cost, conveyance, royalty, taxes etc for all materials as per the drawing, design and direction of Engineer-in-charge.

Extra for every additional depth of 0.10mtr or part there of inspection chamber as of previous item of size 900x800mm from 450mm to 900mm depth (data for 0.10 mtr per each)

Supplying all materials,labours,T&P and constructing inspection chamber/manhole of 1200mmx 900mmx900mm with cement concrete (1:3:6) on bed with hard granite metal size 40mm of 150mm thick and flyash brickwork in cement mortar (1:4) in foundation and plinth, 150mm thick RCC M25 cover slab with supplying fitting and fixing of medium duty SFRC manhole cover, moulding and shaping the channel and benching with cement concrete (1:2:4) using 12mm size hg chips,12mm thick cement plaster in cement mortar (1:3) with punning to inside, cement plaster in CM (1:3) to outside the chamber including centring, shuttering, providing required quantity of MS rods and binding wires for reinforcement, bending, binding, tying the grills and placing in the proper position and drawing and design and PH specification including cost, conveyance, royalty, taxes etc for all materials all complete as per the drawing, design and direction of Engineer-in-charge.

Extra for every additional depth of 0.10mtr or part there of inspection chamber as of previous item of size 1200x900mm from 900mm to 2.5mtr depth (data for 0.10 mtr per each)

Construction of circular brick masonary manhole chamber of size 1.20 x 0.90 mtr including cement concrete (1:3:6) in bed by using 40mm size granite metal, brickwork in CM (1:4) in foundation & plinth, cement plastering (1:3) over flyash brick, plastering in CM (1:3) with neat cement punning, CC (1:2:4) over bed for benching and channeling, RCC M25 for roof slab of 150mm thick and supply fitting and fixing SFRC medium duty type cover including cost of centring and shuttering cost of MS rod for RCC work, supplying fitting and fixing of the polypropelen step iron of required interval etc all complete with all cost, conveyance, royalties taxes etc all complete as per direction of Engineer-in-charge.

Extra for every additional depth of 0.10mtr or part there of manhole size 1200x900mm from 1100mm to 1650mm depth (data for 0.10 mtr per each)

Construction of circular brick masonary manhole chamber of size 1.20 x 1.670 mtr including cement concrete (1:3:6) in bed by using 40mm size granite metal, flyash brickwork in CM (1:3) in foundation & plinth, cement plastering (1:3) over flyash brick, plastering in CM (1:3) with neat cement punning, CC (1:2:4) over bed for benching and channeling, RCC M25 for roof slab of 150mm thick and supply fitting and fixing SFRC medium duty type cover including cost of centring and shuttering cost of MS rod for RCC work, supplying fitting and fixing of the polypropelen step iron of required interval etc all complete with all cost, conveyance, royalties taxes etc all complete as per direction of Engineer-in-charge.

Extra for every additional depth of 0.10mtr or part there of manhole size 1200x1670mm from 1650mm to 2300mm depth (data for 0.10 mtr per each)

Supplying all materials, labour, T&P and laying of UPVC SWR pipes & fittings of approved make confirming to IS-13592,in trenches as sewer line including jointing, laying in proper gradient etc all complete as per the PH specification and direction of the Engineer-in-charge. 100mm Dia

150mm Dia

Supplying all materials, labour, T&P and necessary materials towards laying of RCC NP2 Hume pipe push tight joint type (including cost of RCC Hume pipe) inside the pipeline trench of required size with plastic rope without damage to the pipe with all convenience the materials to site and including all taxes all complete as per direction of Engineer-in-charge. (150mm Dia)

200mm Dia

250mm Dia

Providing and laying in trench cement concrete ( 1:3:6 ) with 40mm size hard granite metal in the following type of bedding for pvc pipes of the following internal diameter including curing complete as per specification (A1-Type Bedding) 150mm Dia

200mm Dia

250mm Dia

Providing and laying plain cement concrete of (1:2:4) for mending of sewer line trench using 12 mm. Size black hard crusher broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required for the work etc complete as per the instruction of the Engineer-in-Charge.

Providing 16mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) finished smooth to outside smooth surface of brick masonry walls after scraping, cleaning and racking out the joints including watering and curing, rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and taxes of all materials and cost of all labours, sundries, T&P and scaffolding required for the work etc. complete in all respect as desired by the Engineer in charge.

Supplying all materials, labour, T&P and providing , fitting & fixing 100mm x100mm x100 mm SW Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification and direction of the Engineer in charge.

Supplying all materials ,labour, T&P and making MS Step Iron in 20mm diameter MS steel bars & fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

Supplying and fixing 900mm dia SFRC cover without frame for manhole including cost of all materials, T&P, labour etc complete as per direction of Engineer-in-charge.

Supplying all materials,labours,T&P and constructing 1.22m dia and 2.1m depth soakway pit with precast RCC rings joined loose,gravel backing in the rear of well steining,precast RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including cutting hole in the rings for inlet pipe,earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty etc all complete as per approved specification and direction of Engineer-in-charge.

Providing and laying in trenches DWC perforated pipe@ 100mm dia conforming to IS 16098 (Part-2) with all fitting accessories and jointing, including testing as per specification complete. (Earth work in trenches to be measured and paid fo separately). The cost inclusive of labour,material,fitting and fixing, conveyance, loading and unloading etc all complete as per the direction of Engineer-in-charge.

Providing and laying in trenches PVC non perforated pipe @160mm dia conforming to IS 4985-2000 with all fitting accessories and jointing, including testing as per specification complete. (Earth work in trenches to be measuredand paid fo separately)The cost inclusive of labour,material,fitting and fixing, conveyance, loading and unloading etc all complete as per the direction of Engineer-in-charge.

ELECTRICAL Recessed wirring to light point with 1.5 Squre Metersm FRLS PVC insulated copper conductor of ISI marked with 20 mm dia PVC heavy class FRLS Numbersn metallic conduit with 6A modular type switch ISI marked , and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size, MS box with 1.5 sq. mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.) Group A

Group B

Group C

Recessed wiring to Fan Point in Group B

Group C

Recessed wiring to Call Bell Point in Group B

Group C

Recessed wiring to Exhaust Fan Point in Group B

Group C

S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof. (M-22)

S/F of Angle holder replacing Ceilling Rose(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.))

S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 Numbers of 3pin 5/6amp modular socket out let & 2 Numbers of 5/6 amp piaNumbers type modular switch, connection, painting etc as required. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piaNumbers type Modular switch & Socket, connection, painting etc as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Power point with 4 modular & 2 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piaNumbers type Modular switch & Socket & Mini DP MCB, connection, painting etc as required for AC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 18 SWG Modular metal box of following sizes (Numbersminal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2 Modular box with base & cover

4 Modular box with base & cover

6 Modular box with base & cover

8 Modular box with base & cover

12 Modular box with base & cover

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia Numbersn metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2x1.5+1x1.5 (1.8.1)

S/F of 'B/C/D' series SP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP) (2.6.1) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 40A four pole (triple pole and neutral) 410 V residual current break (RCCB) having a sensitivity current up to 300 milli ampere in the existing MCB DB ISI marked complete with connection testing and commissioning etc as required(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 'B/C/D' series TPN MCB of 5 - 63A amp rating (As per direction of engineer in charge) 440Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required without MCB box(2.6.4) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)S/F of 4 way (4+12) TPN MCB DB double door (2.5.5)

S/F of 6 way (6+18) TPN MCB DB double door (2.5.6)

Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17)

Supply & laying 8 SWG Cu wire in recess for loop earthing as required (3.18)

S/F of G.I.Earth Plate Earthing 600 mm x600mmx6mm with Salt & Charcoal for Earth electrode (3:4)+(3.6)

S/F of Cu .Earth Plate Earthing 600 mm x600mmx3.15mm with Salt & Charcoal for Earth electrode (3:5)+(3.6)

S/L of 25mm x 6mm G.I. earth strip in ground(3:10)

S/L of 25mm x 5mm Cu. earth strip in 40 mm dia G.I.Pipe(3.11)

Supply and fixing of 300mm Exhust fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Call bell/Buzzer(Ding dong type) ISI marked suitable for DC/AC single phase 230 volts complete as required. (1.30)

S/F of 18-25Watt L.E.D Tube light fitting with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 1200mm Sweep BLDC Ceiling Fan with Aluminium Blades having watage Numberst more than 28 watt & Air Deleivery greater than equals to 215m3/min. (Replacement warranty will be 4 years)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F step type modular fan regulator (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15mm dia down rod with all accessories (1.39+1.41)

Supply and fixing of 400 mm wall fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of superior type Led bulk head fitting general domestic use ISI marked square / oval type including necessary connections. ( M-5 ) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 45-48 Watt Single LED Street Light Fitting with LED & Electronic driver For Building Premises Light with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15w Watt LED Bulb (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 12W LED Squre (10"×10") LSDSMN-12W-WW with surface Panel rings (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying an fixing of recess/surface mounted 2'x2' 36 W(595mmx595mmx70mm) square shaped LED with lumen efficacy Numberst less than 130lm/W, CRI Numberst less than 80, CCT of 5700-6500 degree K, THD less than 10%,internal surge protection of 3 KV, complete with Numbersn integrated isolated electronic driver (protects the output /secondary side from any disturbance on the input / primary side ensuring safe operation)and all other accessories suitable for operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (5 years warranty) as required as per direction of Engg.-in-Charge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, Installation, Testing and Commissioning of Linear LED SPorts light with Max system power of 80W , CCT 5700K +/-355K as per ANSI , CRI>80, SDCM<3 , with Minimum delivered lumen of >11,500 lumens . The fixture housing must be Made of extruded Aluminium housingfor better thermal healing & Powder coated by Corrosion resistant NaNumbers coating techNumberslogy. Luminaire must have minimum Ingress protection of IP66 and Impact Resistance of IK08. The fixture should be equiped with stabilized Injection moulded special PC diffused optics ensuring low glare & best in class uniformity( Glass cover Numberst allowed) . Luminaire housing should carry OEM's logo embossed / engraved (Numbers stickering is allowed). the Length of Luminaire should be between 900mm-1200mm . The luminaire must have Integral high efficiency electronic thermally isolated constant current IP66 driver with operating voltage range of 90-305V, power factor > 0.95, THD < 10%, with Inbuilt surge protection of : DM 4kV, CM 6kV and upgraded with integrated External IP67 protected SPD of 20KV/10KA surge protection . D . Weight of the Luminaire i should be less than 3 Kg .Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. CE Certified, ROHS compliant, BIS Certification for Luminaires & Drivers. All supporting documents like Technical data sheet of Luminaire & Driver, test reports including test reports photometry , TTC, IP, IK, Vibration and salt spray test from OEMs Own NABL accredited Laboratory. LM80 from LED OEM in 100% compliance with the specified luminaire technical requirements, shall be mandatorily submitted along with the bid.BIS of the Luminaire should carry the Own factory address of OEM, vendor facilities are Numberst acceptable. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 4x6Squre Metersm (37) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 3 1/2 x50Squre Metersm (26) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 3 1/2 x95qmm (28) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Laying of MV cable upto 25Squre Metersm in ground (5.1.1)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm in ground (5.1.2)

Laying of MV cable upto 25Squre Metersm on surface (5.5.1)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm on surface (Horizontally)(5.5.2)

S/M of end termination of LV/MV cable size 3 1/2 x50 Squre Metersm (5.8.22)

S/M of end termination of LV/MV cable size 3 1/2 x95 Squre Metersm (5.8.24)

S/I/T&Commissioning of LT indoor floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by siemens gray powder cote paint is designed as G.A drawing as per direction of Engg.-in-Charge.Warrentee period of replacement of panel & accessories must be with compelete test certificate must be submitted along with panel board including component list. 80X10MM Separate Aluminium Earth bus bar should be installed.Warrentee period of replacement of panel & accessories must be 1 years & compelete test certificate must be submitted along with panel board including component list.All the outgoing and incoming feeders shall have ON/OFF/TRIP indication and digital mutifunction meter with RS 485 compatability.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)In commer-1- 01 number 4p 125A 4P MCCB with ROM 25kA with adjustable MICRO PROCESSOR Release with Ics=100% Icu. Out going- 2 numbers of 63A 4P MCB 10KA & 4 numbers of 40A 4P MCB 10KA,Out going- 7 numbers of 40A 4P MCB 10KA & 3 numbers of 40A DP MCB 10KA (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 200mm(W) of ..The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 300mm(W) .The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of (IS/IEC 62561).Minimum cross sectional area should be 50 Squre Metersm for Al. Round ,complied as per IS/IEC 62561-2. i) Electrical resistivity-0.034 ii) Lighting impluse current of 100 kA for 10/350 iii) Tensile strength-178 mpa or N/mm2 .(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Roof conductor holder for parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder at every 1 meter distance. Complied as per IS/IEC 62305-3 & tested as per IEC 62561-2 (Make: OBO/DEHN/ABB/Cape/Equivalent brand as per the direction of Engg.-in-Charge)

Provision of Polyamide roof cable holder for flat roof: (frost-resistant concrete). Sleeve from polyethylene, black Conductor holder at every 1 meter distance & Complied as per IS/IEC 62305-3 & tested as per IEC 62561(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of 2 Meters Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 . Numbersminal size Ø10/16 mm aluminium rod: 2 Meters Airterminal: semi-hard (E-AlMgSiO5 corresponds to IEC-62305 & IEC-62561) Suitable for high wind load. Providing of Stand for Fang Fix system 16/17 kg with base ,made up of frost resistant concrete, stainless steel clamp, tested for 100KA lightning current, complied as per IS/IEC 62305-3, tested as per IEC 62561-1 . 16kG concrete Base should be provided for 2 Meters Airterminal. air termination rod of 2 Meters length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends(Tappered Type). The rod shall be mounted with supporting concrete block and fixing accessories . Test Parameter for 2 Meters vertical air terminal a)ELectrical Resistivity b) Tensile Strength c) Condition of Salt Mist (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.) Tested as per IEC-62561

Provision of T-cross / parallel connectors made of Stainless steel 304 grade .installation using hexagonal bolt M10X30 high grade stainless steel. Tested for 100kA lightning current.Tested for 100 KA lightning current as per IEC 62561-1 / Expansion Joint with connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations. Expansion Joint should be considered at every 20 Meters length of straight horizontal air termination and connected at both the end with use of straight connector conductor(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of (IS/IEC 62561).Minimum cross sectional area should be 50 Squre Metersm for Al. Round ,complied as per IS/IEC 62561-2. i) Electrical resistivity-0.034 ii) Lighting impluse current of 100 kA for 10/350 iii) Tensile strength-178 mpa or N/mm2(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Roof conductor holder/Polyamide holder with stainless steel base(V2A) bottom section with Ø8.5mm slot conductor holder@1 Meters distance & Complied as per IS/IEC 62305-3 & tested as per IEC 62561-2 / Stainless steel SS 304 Grade Conductor Holder for fixing the 8mm dia round conductor on the side wall . Test Parameter: Tested as per IEC 62561 (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Test Joint (Folding Clamp) made of Stainless Steel suitable to connect 8mm round conductor and max by 30x3/25x6 mm GI strip as specified in drawing and directed by Engineer provided by The cable junction boxes can be mounted on mounting plates with sheet metal screws 3.5 x 9.5 in openings on the floor. Internal dimensions: 100x100x48 mm ,Cover with labeling field and sealable.Internal dimensions: 100x100x48 mm.Degree of protection IP66; Degree of protection IK-Code IK07 / Stainless Steel Test Joint with enclosure (IP-65) to interconnect between 8 mm Al. round conductor to Flat conductor( 30x3mm) Test Parameter: Salt Spray Test for test joint plate -Numbers sign of Corrosion Tested as per IEC 62561-1 (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Galvanised Steel Flat 30X3 mm of thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized., Zinc Coating thickness- Avg. 70 microns. , as per IEC 62561-2.,(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Stainless steel Cross Connector for flat conductor at cross junction. Test Parameter Salt Spray Test ( IEC 62561-1) - Numbers sign of Corrosion. Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 Numbers of bolt.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of of Stainless Steel Conductor Holder for fixing the flat conductor on the side wall. Test Parameter: Salt Spray Test - Numbers Sign of Corrosion Tested as per IEC 62561-1 /flat conductor holder, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot dip galvanised steel, Bottom section from polyamide, black (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm of length 5 Meters. Made of petrolatum- coated chemical fibre fabric to meet the requirement of IS/IIEC-62305 (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of (A)UL Listed & CPRI Tested maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17 mm with copper coating thickness of 250micron tested as per IEC 62561-2. The rod should have been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467.-1 Numbers(B)Universal clamp made of SS to connect rod with flat conductor -1 Numbers (C)Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. (D) The above arrangements shall be provided with Heavy duty earth champer of 6000kg load bearing capacity to ensure the safety of earthing system .Earth Electrode Shall be tested as per IEC 62561-2. 1) Copper Coting Thickness- Minimum 250Micron. 2) Electrical Resistivity Test : Maximum electrical resistivity should be 0.25 Micro Ohm Meter for Copper coated steel. 3) Electrical resistance Test before and after salt mist test. 4) Tensile Test. 5) Bend Test 6) Adhesion Test. The Earth Enhancing Mineral Compound shall be tested as per IEC 62561-7. 1. Sulphur Content: Less than 2% 2. Resistivity 0.2 ohm m. 3. The Compound shall be tested and passed Toxicity Leaching Characteristic Leaching Properties. 4. Corrosion resistance : The Value observed under dry and wet Condition is greater than 4 ohm meter square. 5. The Earth Enhancing Mineral compound is Numbersn-hazardous in nature.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of CLASS 1 +2 SPD, for power line protection, 4P ( 3PHASE + NEUTRAL), Impulse Discharge Current/POLE (10/350 s) (L - N) /(N - PE) imp,12.5 kA ( As per NBC),Numbersminal AC Voltage (50/60Hz) Uo / Un 240 V,Maximum Continuous Operating Voltage 300 V, Numbersminal Discharge Current (8/20 s) (L - N) / (N - PE) In-20KA/50 KA, Maximum Discharge Current (8/20 s) (L - N) / (N - PE) Imax -50 kA / 100 kA, Impulse Discharge Current (10/350 s) (L - N) /(N - PE) imp,12.5 kA / 50 kA, Location of Use: Main Distribution Boards Network Systems: TT, TN-S,Mode of Protection: L-N,N-PE,IEC/EN/UL Category: Class I+II / Type 1+2 / Type 1CA,Open Type 1 SPD Listed,Housing: Pluggable Design, Compliance:NBC-2016, NEC-2023,IS/IEC-62305, IEC 61643-11:2011,EN 61643-11:2012 +A11:2018,UL 1449 5th Edition . 'along with all accesories connecting cables, lugs etc(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Installation Charges for the LA Sysytem Including with all materials accessories ( Screw Grip, Saddle, anchor) which is required for the complete Installation. Message on wall

Supply ,installation ,testing & commissioning of 10KVA Parallel UPS SYSTEM WITH IGBT based inverter system, true online double conversion system, inbuilt isolation transformer & automatic phase sequence corrector of 3ph in put to 3 ph output,415V, with built in BMS with battery back up up to 30 minutes with MS Rack for battery Housing, DC cable 7 Meters with SFU and links for installation (Battery required: 12V, 100AH, 60 Numberss) protection for fault by OL,UV,EF,GF,OC,Ph. . Warranty period of all accessories & component & system must be 2 years & complete test certificate must be submitted along with ups including component list & SLD.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, installation, testing and commissioning of Tube Axial flow fans complete with tube casing, impeller, bird screen, gravity louvers, necessary nut bolts, necessary transition piece and canvas connection for proper installation, directly coupled to TEFC Sq.cage, IE-3 High efficiency induction motor Class"F" insulation mounted on vibration isolators suitable for 415V±10%, 50 Hz. 3 phase electric supply complete as per the technical specifications enclosed. The fans should be AMCA certified for air and sound performance.The fan shall be complete in all respect and should match the specification ,Drawings and Schedule.The quoted price shall consist of mounting arrangemnt along with spring isolator for fan including the cost of labor & material T & P as required as EIC.7000 CFM ,Total static pressure of 40 mm (Exhaust air) (2w+1S)

7000 CFM ,Total static pressure of 40 mm (Fresh air) (2w+1S)

Supply of GSS Ducting as per ISI Standards and specification and providing openings wherever required in the existing civil structure and fixing of clamps,8 mm GI threaded rod and angle supports, hangs, etc including the cost of labor & material T & P as required as EIC.0.8 mm thick

0.63 mm thick

Suppling and fixing of powder coated, extruded aluminium grille without volume control dampers and fix up in positions with necessary frames, beedings and finished complete in coordination with civil works for use including the cost of labor & material T & P as required as EIC.200 mm linear grills

Supplying and fixing of volume Control Dampers made out of 1.6 mm thick galvanised sheet steel frame and blades of 1.6 mm galvanised sheet steel with linkages, operating handle & depth of 150mm with 40mm flanges all around suitable for manual control locations as reqd. including the cost of labor & material T & P as required as EIC.

Supply, installation testing and commissioning of MS angel,chanel,frame,nut,bolts etc/welding as per requirement for supporting of ducts from truss including the cost of labor & material T & P as required as EIC.

Supplying, Installing, Testing and commissioning of electrical motor driven booster pump of MoNumbersblock type capable to deliver 450LPM at 35MWC. The pump shall be coupled to TEFC motor of suitable HP with speed of 2900RPM and complete set shall mounted on common base frame as per direction of engineer in charge(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

1100 V GRADE POWER/CONTROL CABLES :SITC of FRLS, PVC outer sheateh, steel armoured, aluminium, 1100v grade power cables with glands etc. The minimum size of the cables shall as mentioned below as per direction of engineer in charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.). 3.5C x 10 mmsq

2 C x 1.5 mmsq

Supplying, Installing, Testing and commissioning of waffer type C.I. Numbersn-return valves as per with required flanges, nuts, bolts and gaskets etc. complete of size 100 mm Numbersminal dia.as per direction of engineer in charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying, Installing, Testing and commissioning of CI butterfly valves (PN 10) as per BS 5155 slim seal standard lever operated type with required flanges, nuts, bolts etc. complete of size 100 mm Numbersminal dia (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing, installing and commissioning C.I. flanged "Y" type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Gun metal chrome finished Ball valves with fittings of screwed end type.as per direction of engineer in charge of size 15 mm dia.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installaion of pressure switches of suitable range for pump sets (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.).

Supply and installaion of pressure gauges of suitable range for pump sets (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying, Installing, Testing and commissioning of MS PIPEsw conforming to IS 1239 Pt - I Heavy grade with fittings such as Reducers, Tees, elbows, flanges with painting of 1 coats of red oxide primer and 2 coats of PO red paint of size100 mm Numbersminal dia.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying, Installing, Testing and commissioning of MS PIPEsw conforming to IS 1239 Pt - I Heavy grade with fittings such as Reducers, Tees, elbows, flanges with painting of 1 coats of red oxide primer and 2 coats of PO red paint of size 40 mm Numbersminal dia .(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying & fixing first aid fire hose reel of thermoplast braided suitably reinforced 20 mm size & 30 m standard length with 5 mm tapering branch Numberszzle, 25mm dia. Pipe to connect to riser with cut off ball valve attachment. Hose to be swinging type wall mounted drum & recessing into hose cabinet to suit location including fixing with lead anchor fasteners & bolts (Including drum and swivel arrangement) etc complete(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying and fixing of automatic air release valve with unions etc. complete.as per direction of engineer in charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Gun metal chrome finished Ball valves with fittings of screwed end type. Of size25 mm dia.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying and fixing 2 way fire brigade connection of cast iron body with 2 Numbers Gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for 100 mm dia MS pipe connection, conforming to IS904 as reqd.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Flexyle Photoluminescent based Glow-in-the-dark sheeting with luminious properties enclosed in a weather-proof UV stabilized film with UV screen printing by imported inks pasted over 5 mm Thick Cast Acrylic Sheet with the Protection of 3 mm Thick Cast Acrylic from Front side with S.S stud for fire order, fire action and fire evacuation signages.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Manual Fire AlarmSystem-:Supply, installation, testing and commissioning of Conventional type Main Fire Alarm Control Panel (FACP), the panel shall be conventional type fire detection and alarm system with capacity of 4 zone complete with all accessories and battery back up for 48 hours in standby mode and 15 minutes in alarm condition. The panel shall have minimum of 80 character display complete accessories.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying, installing, testing and commissioning of conventional type Hooter at 85 dBA @ 3m for Audible annunciation and 75cd flashing at 1 Hz for visual indication with all accessories etc., complete. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying, installing, testing and commissioning of conventional type Manual call point with all accessories complete. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, installation, connecting, testing and commissioning of conventional type heat cum Photoelectric Smoke Detector With Remote Indicator Output and Magnetic Test Function, With Base (Certified by LPCB).(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg . (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing & fixing Water based Carbon-di-oxide 4.5 ltrs. fire extinguishers as per IS specification consisting of welded MS cylindrical body ,squeeze lever discharge valve fitted with internal discharge tube ,30 cm long high pressure discharge hose ,discharge Numberszzle,suspension brackets,finished exteranally with red enemel paint and fixed to wall with brackets with rawl plug/dash fastners complete with initial charging. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and laying of 4 pair Cat6 U/UTP Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall Numberst be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance Less than equals to 9.38 omm/100m Max., Cable support Delay Skew: less than 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 omm @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of Cat6 I/O with single Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold greater than 0.8 m. The connectors shall be compatible as per IEEE 802.3af standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Numbersn Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion, RJ45, 8P8C, 2 FORK 50 inch Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)For 1 Meters. Long

For 2 Meters. Long

Supply and fixing of 12U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 Squre Metersm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2Numbers 1U Metal Cable manager with Plastic cable loops and H/W screw. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 24 Port Layer2 Giga (10/100/1000BaseT) PoE Switch with 4 x 1Gig SFP Port , Switching Capacity 56 Gbps, Throughput 41.7 Mpps ,Management Port 1 x RJ 45 Console port ,PoE power budget 370 Watt, Switch should support IEEE 802.3af & IEEE 802.3at standard ,MAC Address 16K , Jumbo Frame 12K ,Temperature Working 0°C~50°C, storage -40°C~70°C, Power Supply AC: 100~240VAC. All hardware should supplied with necessary mounting brackets and IN power cord with 3 years of comprehensive onsite warranty. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Termination & link testing of LAN cable at both the end including the cost of labor & material T & P as required as EIC.

Supply & fixing of 5MP Dome IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQC, FCC, CE, BIS certified.) with accessories as require.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of 5MP Bullet IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQCL, FCC, CE, BIS certified.) with accessories as require.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of 16CH 2 SATA NVR Support 12MP/8MP / 5MP / 4MP / 3MP / 1080P / 960P IP Adopt standard H.265 high profile compression format, With 4k Video Output, Compression Standard H.265, Network Access Bandwidth 320Mbps, HDD SATA × 8(Upto 10TB Supported), 1- e-SATA And 2-way Audio RCA × 1, Local Output RCA × 1, USB 2.0 × 2 (one in the front panel and the other in the rear panel), USB 3.0 × 1 (rear panel) (UL, FCC, CE, BIS certified) including the cost of labor & material T & P. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 8 TB Storage Capacity,including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of 43" UHD (3,840 x 2,160) TV with 300 nits brightness,10W+10W Audio Output,Crestron Connected®, NTP sync timer, BEACON, Embedded CM (contents manager), Soft AP, WiFi , Screen Share (Miracast), DIAL, Bluetooth Audio Playback,Hotel Mode , Welcome Screen (Splash Image), Insert Image, One Channel Map, IP Channel Manager, External Speaker Out , Remote jack pack, Moving Picture Playback, Auto Off / Sleep Timer,Smart Energy Saving, Motion Eye Care,USB Cloning, WOL, Interface : Set Side - HDMI In 3, USB 1, CI Slot, RF In, Digital Audio Out (Optical), RS-232C, RJ45 , External Speaker Out,Power Consumption(Typ.)-145 W, with 3years Warranty including the cost of labor & material T & P as required as EIC.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and laying of 6 core Single mode OS2 Unitube Armoured Optical fiber cable through existing conduit: The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. Outdoor Corrugated Steel tape Central loose tube. ( Standard Approved: ISO 11801 2nd edition/ EN 50173-1:2002 / IEC 60794-1/IEC 60793-2-50 class B1.3 / EN 60793-2-50: class B1.3 / ITU Recommendation G.652.D - the oder ITU designations A, B and C are also fulfilled / OS1/ISO/IEC 24702:2006, cat. OS2; also OS1 requirements are fulfilled/IEEE 802.3 - 2002 incl. 802.3ae ) Jacket. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of 1000BASE-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um Single mode Fiber Type up to 20 KM. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of OFC PATCHCORD, SM (OS2), DUPLEX LC-SC, PC TYPE, 3M, LSZH Fiber Optic Single Mode OS2 Patch Cords are offered in LSZH Jackets with Corning Fiber,Insertion Loss : <= 0.2 db, Max 0.3db/MetersJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db, APC>=60db.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of 6 Port Rack mount Draw Type Loaded LIU available in Standard 19 inch ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled Steel as Raw Material , Consist of Top Cover and Bottom Panel , Easy to Assemble and Dissemble , Three Types of Input Holes Cable Entry Through Water Proof Cable Clamp , 3 Duplex SC or LC Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,ADAPTER, SM, SIMPLEX SC, PC TYPE ,Support the TIA/EIA Telecommunication Wiring Standards. Compact Design , Telcordia GR-326-Core and PIGTAIL, SM (OS2), SIMPLEX SC, PC TYPE, 2M, LSZH ,Insertion Loss : <= 0.2 db, Max 0.3db/MetersJ: Max 0.5db Return Loss : PC greater than eaquals to 45db, UPC greater than eaquals to50db, APC greater than eaquals to60db ,LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , 100% Factory Tested , Low Insertion Loss and Return Loss. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of SIP IP Horn Speaker with Built-in 30W amplifier IP67 rating, with PoE 802.3af enabled (Power-over-Ethernet) ,48K OPUS,G711U,G711A GSM MP3Audio Codec, Suppurt RTP Multicast. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of SIP IP Wall Speaker with Built-in 15W amplifier, IP55 rating with PoE 802.3af enabled (Power-over-Ethernet) ,48K OPUS,G711U,G711A GSM MP3Audio Codec, Suppurt RTP Multicast. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of IP Pagging microphone should support6 SIP lines, Android system, 16G EMMC, WiFi, RTP multicast paging, Real-time monitoring, Support HTTP server, USB disk music, 7.0-inch touch screen, 1024*600 resolution, HDMI interface (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Recessed wirring to light point with 1.5 Squre Metersm FRLS PVC insulated copper conductor of ISI marked with 20 mm dia PVC heavy class FRLS Numbersn metallic conduit with 6A modular type switch ISI marked , and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size, MS box with 1.5 sq. mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.) -do- Group A

Group B

Group C

Recessed wiring to Fan Point in Group B

Group C

Recessed wiring to Call Bell Point in Group B

Group B

Group C

S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof. (M-22)

S/F of Angle holder replacing Ceilling Rose (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 Numbers of 3pin 5/6amp modular socket out let & 2 Numbers of 5/6 amp piaNumbers type modular switch, connection, painting etc as required. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piaNumbers type Modular switch & Socket, connection, painting etc as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Power point with 4 modular & 2 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piaNumbers type Modular switch & Socket & Mini DP MCB, connection, painting etc as required for AC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 18 SWG Modular metal box of following sizes (Numbersminal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2 Modular box with base & cover

4 Modular box with base & cover

6 Modular box with base & cover

8 Modular box with base & cover

12 Modular box with base & cover

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia Numbersn metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2x1.5+1x1.5 (1.8.1)

S/F of 'B/C/D' series SP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP) (2.6.1) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 40A four pole (triple pole and neutral) 410 V residual current break (RCCB) having a sensitivity current up to 300 milli ampere in the existing MCB DB ISI marked complete with connection testing and commissioning etc as required(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 'B/C/D' series TPN MCB of 5 - 63A amp rating (As per direction of engineer in charge) 440Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required without MCB box(2.6.4) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)S/F of 4 way (4+12) TPN MCB DB double door (2.5.5)

S/F of 6 way (6+18) TPN MCB DB double door (2.5.6)

Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17)

Supply & laying 8 SWG Cu wire in recess for loop earthing as required (3.18)

S/F of G.I.Earth Plate Earthing 600 mm x600mmx6mm with Salt & Charcoal for Earth electrode (3:4)+(3.6)

S/F of Cu .Earth Plate Earthing 600 mm x600mmx3.15mm with Salt & Charcoal for Earth electrode (3:5)+(3.6)

S/L of 25mm x 6mm G.I. earth strip in ground(3:10)

S/L of 25mm x 5mm Cu. earth strip in 40 mm dia G.I.Pipe(3.11)

Supply and fixing of 300mm Exhust fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Call bell/Buzzer(Ding dong type) ISI marked suitable for DC/AC single phase 230 volts complete as required. (1.30).(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 18-25Watt L.E.D Tube light fitting with all accessories and connections(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 1200mm Sweep BLDC Ceiling Fan with Aluminium Blades having watage Numberst more than 28 watt & Air Deleivery greater than equals to 215m3/min. (Replacement warranty will be 4 years)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F step type modular fan regulator (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15mm dia down rod with all accessories (1.39+1.41)

Supply and fixing of 400 mm wall fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of superior type Led bulk head fitting general domestic use ISI marked square / oval type including necessary connections. ( M-5 ) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 45-48 Watt Single LED Street Light Fitting with LED & Electronic driver For Building Premises Light with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15w Watt LED Bulb (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 12W LED Squre (10"×10") LSDSMN-12W-WW with surface Panel rings(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying an fixing of recess/surface mounted 2'x2' 36 W(595mmx595mmx70mm) square shaped LED with lumen efficacy Numberst less than 130lm/W, CRI Numberst less than 80, CCT of 5700-6500 degree K, THD less than 10%,internal surge protection of 3 KV, complete with Numbersn integrated isolated electronic driver (protects the output /secondary side from any disturbance on the input / primary side ensuring safe operation)and all other accessories suitable for operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (5 years warranty) as required as per direction of Engg.-in-Charge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 3 1/2 x 35Squre Metersm (25)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 3 1/2 x50Squre Metersm (26)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm in ground (5.1.2)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm on surface (Horizontally)(5.5.2)

S/M of end termination of LV/MV cable size 3 1/2 x35 Squre Metersm (5.8.21)

S/M of end termination of LV/MV cable size 3 1/2 x50 Squre Metersm (5.8.22)

S/I/T&Commissioning of LT indoor floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by siemens gray powder cote paint is designed as G.A drawing as per direction of Engg.-in-Charge.Warrentee period of replacement of panel & accessories must be with compelete test certificate must be submitted along with panel board including component list. 80X10MM Separate Aluminium Earth bus bar should be installed.Warrentee period of replacement of panel & accessories must be 1 years & compelete test certificate must be submitted along with panel board including component list.All the outgoing and incoming feeders shall have ON/OFF/TRIP indication and digital mutifunction meter with RS 485 compatability(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)In commer-1- 01 number 4p 100A 4P MCCB with ROM 25kA with adjustable MICRO PROCESSOR Release with Ics=100% Icu. Out going- 2 numbers of 63A 4P MCB 10KA Sub incommer-01 number 80A 4P Change Over Switch. Out going- 1 Numbers 63A 4P MCB 10KA, 4 numbers of 32A 4P MCB 10KA & 3 numbers of 40A DP MCB 10KA .(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 200mm(W) of .The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying,fixing of perforated cable trays with horizental & vertical bends,reducers ,tees,crossover,brakets & other accessories ar requited confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x 300mm(W) e.The Load bearing capacity of the Cable Trays should be minimum of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required as per direction of Engg.-in-Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg .(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing & fixing Water based Carbon-di-oxide 4.5 ltrs. fire extinguishers as per IS specification consisting of welded MS cylindrical body ,squeeze lever discharge valve fitted with internal discharge tube ,30 cm long high pressure discharge hose ,discharge Numberszzle,suspension brackets,finished exteranally with red enemel paint and fixed to wall with brackets with rawl plug/dash fastners complete with initial charging. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and laying of 4 pair Cat6 U/UTP Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall Numberst be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance graeter than equals to 9.38 ohm/100m Max., Cable support Delay Skew: greater than 45 ns/100m, Operating Voltage: 72V , Impedance: 100 equals to 15 omm @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of Cat6 I/O with single Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold > 0.8 m. The connectors shall be compatible as per IEEE 802.3 of standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Numbersn Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50 inch Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)For 1 Meters. Long

For 2 Meters. Long

Supply and fixing of 12U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 Squre Metersm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2Numbers 1U Metal Cable manager with Plastic cable loops and H/W screw.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 24 Port Layer2 Giga (10/100/1000BaseT) PoE Switch with 4 x 1Gig SFP Port , Switching Capacity 56 Gbps, Throughput 41.7 Mpps ,Management Port 1 x RJ 45 Console port ,PoE power budget 370 Watt, Switch should support IEEE 802.3af & IEEE 802.3at standard ,MAC Address 16K , Jumbo Frame 12K ,Temperature Working 0°C~50°C, storage -40°C~70°C, Power Supply AC: 100~240VAC. All hardware should supplied with necessary mounting brackets and IN power cord with 3 years of comprehensive onsite warranty. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Termination & link testing of LAN cable at both the end including the cost of labor & material T & P as required as EIC.

Supply & fixing of 5MP Dome IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQC, FCC, CE, BIS certified.) with accessories as require.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of 5MP Bullet IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQCL, FCC, CE, BIS certified.) with accessories as require.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of 8CH 1 SATA NVR Support 12MP/8MP / 5MP / 4MP / 3MP / 1080P / 960P IP Adopt standard H.265 high profile compression format, With 4k Video Output, Compression Standard H.265, Network Access Bandwidth 320Mbps, HDD SATA × 8(Upto 10TB Supported), 1- e-SATA And 2-way Audio RCA × 1, Local Output RCA × 1, USB 2.0 × 2 (one in the front panel and the other in the rear panel), USB 3.0 × 1 (rear panel) (UL, FCC, CE, BIS certified) including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 4 TB Storage Capacity,including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of 32" UHD (3,840 x 2,160) TV with 300 nits brightness,10W+10W Audio Output,Crestron Connected®, NTP sync timer, BEACON, Embedded CM (contents manager), Soft AP, WiFi , Screen Share (Miracast), DIAL, Bluetooth Audio Playback,Hotel Mode , Welcome Screen (Splash Image), Insert Image, One Channel Map, IP Channel Manager, External Speaker Out , Remote jack pack, Moving Picture Playback, Auto Off / Sleep Timer,Smart Energy Saving, Motion Eye Care,USB Cloning, WOL, Interface : Set Side - HDMI In 3, USB 1, CI Slot, RF In, Digital Audio Out (Optical), RS-232C, RJ45 , External Speaker Out,Power Consumption(Typ.)-145 W, with 3years Warranty including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply ,installation ,testing & commissioning of 5KVA Parallel UPS SYSTEM WITH IGBT based inverter system, true online double conversion system, inbuilt isolation transformer & automatic phase sequence corrector of 3ph in put to 3 ph output,415V, with built in BMS with battery back up up to 30 minutes with MS Rack for battery Housing, DC cable 7 Meters with SFU and links for installation (Battery required: 12V, 100AH, 60 Numberss) protection for fault by OL,UV,EF,GF,OC,Ph. . Warranty period of all accessories & component & system must be 2 years & complete test certificate must be submitted along with ups including component list & SLD.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Recessed wirring to light point with 1.5 Squre Metersm FRLS PVC insulated copper conductor of ISI marked with 20 mm dia PVC heavy class FRLS Numbersn metallic conduit with 6A modular type switch ISI marked , and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size, MS box with 1.5 sq. mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.) Group A

Group B

Group C

Recessed wiring to Fan Point in Group C

Recessed wiring to Call Bell Point in Group B

Recessed wiring to Exhaust Fan Point in Group B

S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof. (M-22)

S/F of Angle holder replacing Ceilling Rose(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 5A. Modular Switch & 5A. Modular Socket outlet of ISI marked on existing board (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 Numbers of 3pin 5/6amp modular socket out let & 2 Numbers of 5/6 amp piaNumbers type modular switch, connection, painting etc as required.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piaNumbers type Modular switch & Socket, connection, painting etc as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 18 SWG Modular metal box of following sizes (Numbersminal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2 Modular box with base & cover

6 Modular box with base & cover

12 Modular box with base & cover

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia Numbersn metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2x1.5+1x1.5 (1.8.1)

S/F of 'B/C/D' series SP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP) (2.6.1) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 32A double pole (single pole and neutral) 240 V residual current break (RCCB) having a sensitivity current up to 300 milli ampere in the existing MCB DB ISI marked complete with connection testing and commissioning etc as required.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)S/F of MCB 12 way Double door (2.3.7)

Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17)

S/F of G.I.Earth Plate Earthing 600 mm x600mmx6mm with Salt & Charcoal for Earth electrode (3:4)+(3.6)

S/L of 25mm x 6mm G.I. earth strip in ground(3:10)

Supply and fixing of 300mm Exhust fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of Call bell/Buzzer(Ding dong type) ISI marked suitable for DC/AC single phase 230 volts complete as required. (1.30)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 18-25Watt L.E.D Tube light fitting with all accessories and connections(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 1200mm Sweep BLDC Ceiling Fan with Aluminium Blades having watage Numberst more than 28 watt & Air Deleivery greater than equals to 215m3/min. (Replacement warranty will be 4 years(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F step type modular fan regulator.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15mm dia down rod with all accessories (1.39+1.41)

Supply and fixing of 400 mm wall fan with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of superior type Led bulk head fitting general domestic use ISI marked square / oval type including necessary connections. ( M-5 )( Make- Philips/Jaquar/Bajaj/Crompton/ Wipro/ Havells/Panasonic/Equivalent brand as per the direction of Engg.-in-Charge )

Supply and fixing of 45-48 Watt Single LED Street Light Fitting with LED & Electronic driver For Building Premises Light with all accessories and connections (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 15w Watt LED Bulb (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

S/F of 12W LED Squre (10"×10") LSDSMN-12W-WW with surface Panel rings(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying an fixing of recess/surface mounted 2'x2' 36 W(595mmx595mmx70mm) square shaped LED with lumen efficacy Numberst less than 130lm/W, CRI Numberst less than 80, CCT of 5700-6500 degree K, THD less than 10%,internal surge protection of 3 KV, complete with Numbersn integrated isolated electronic driver (protects the output /secondary side from any disturbance on the input / primary side ensuring safe operation)and all other accessories suitable for operation on140- 270 V, 50 Hz ,L70 @50,000 burning hrs (5 years warranty) as required as per direction of Engg.-in-Charge (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 4x6Squre Metersm (37) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Laying of MV cable upto 25Squre Metersm in ground (5.1.1)

Laying of MV cable upto 25Squre Metersm on surface (5.5.1)

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg .(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Providing & fixing Water based Carbon-di-oxide 4.5 ltrs. fire extinguishers as per IS specification consisting of welded MS cylindrical body ,squeeze lever discharge valve fitted with internal discharge tube ,30 cm long high pressure discharge hose ,discharge Numberszzle,suspension brackets,finished exteranally with red enemel paint and fixed to wall with brackets with rawl plug/dash fastners complete with initial charging. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and laying of 4 pair Cat6 U/UTP Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall Numberst be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance less than equals to 9.38 ohm/100m Max., Cable support Delay Skew: less than 45 ns/100m, Operating Voltage: 72V , Impedance: 100 15 ohm @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of Cat6 I/O with single Face plate: The Outlet shall meet or exceed requirement as per ANSI/TIA 568C.2,ISO/IEC 11801, & EN50173. The information outlet NEXT, PSNEXT, FEXT, ELFEXT, PSELFEXT and return loss should be verified for CAT6 @ 250Mhz & CAT6A @ 500Mhz. The information outlet connector shall be of gold/nickel, thickness of gold > 0.8 m. The connectors shall be compatible as per IEEE 802.3af standard for POE application. The PVC material of Face plate should complie ABS /UL94-V-O certified. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Numbersn Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and installation of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50 inch Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)For 1 Meters. Long

For 2 Meters. Long

Supply and fixing of 9U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 Squre Metersm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2Numbers 1U Metal Cable manager with Plastic cable loops and H/W screw. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and fixing of 24 Port Layer2 Giga (10/100/1000BaseT) PoE Switch with 4 x 1Gig SFP Port , Switching Capacity 56 Gbps, Throughput 41.7 Mpps ,Management Port 1 x RJ 45 Console port ,PoE power budget 370 Watt, Switch should support IEEE 802.3af & IEEE 802.3at standard ,MAC Address 16K , Jumbo Frame 12K ,Temperature Working 0°C~50°C, storage -40°C~70°C, Power Supply AC: 100~240VAC. All hardware should supplied with necessary mounting brackets and IN power cord with 3 years of comprehensive onsite warranty. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Termination & link testing of LAN cable at both the end including the cost of labor & material T & P as required as EIC.

Supply & fixing of 5MP Dome IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQC, FCC, CE, BIS certified.) with accessories as require.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of 5MP Bullet IR Network Camera (1/3" CMOS sensor, Mini. Pixel of 2688*1520 or higher video quality, frame rate of Up to 25fps, Ultra 265, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30Meters IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for Numbersise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (STQCL, FCC, CE, BIS certified.) with accessories as require(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply and Installation of 8CH 1 SATA NVR Support 12MP/8MP / 5MP / 4MP / 3MP / 1080P / 960P IP Adopt standard H.265 high profile compression format, With 4k Video Output, Compression Standard H.265, Network Access Bandwidth 320Mbps, HDD SATA × 8(Upto 10TB Supported), 1- e-SATA And 2-way Audio RCA × 1, Local Output RCA × 1, USB 2.0 × 2 (one in the front panel and the other in the rear panel), USB 3.0 × 1 (rear panel) (UL, FCC, CE, BIS certified) including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

SITC of 8 TB Storage Capacity,including the cost of labor & material T & P as required as EIC. Make: Segate/WD/Equivalent brand as per the direction of Engg.-in-Charge

Supply and Installation of 32" UHD (3,840 x 2,160) TV with 300 nits brightness,10W+10W Audio Output,Crestron Connected®, NTP sync timer, BEACON, Embedded CM (contents manager), Soft AP, WiFi , Screen Share (Miracast), DIAL, Bluetooth Audio Playback,Hotel Mode , Welcome Screen (Splash Image), Insert Image, One Channel Map, IP Channel Manager, External Speaker Out , Remote jack pack, Moving Picture Playback, Auto Off / Sleep Timer,Smart Energy Saving, Motion Eye Care,USB Cloning, WOL, Interface : Set Side - HDMI In 3, USB 1, CI Slot, RF In, Digital Audio Out (Optical), RS-232C, RJ45 , External Speaker Out,Power Consumption(Typ.)-145 W, with 3years Warranty including the cost of labor & material T & P as required as EIC. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & fixing of IP Based PoE Phone, 2 SIP accounts, 2 line keys, 3-way conferencing, 3 XML programmable context-sensitive soft keys, Dual-switched 10/100 mbps ports, integrated PoE, HD audio on speakerphone and handset. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply,Installation,Testing & Commissioning of 1-PH I/P & O/P ,1 KVA line interactive UPS. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia Numbersn metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)2x1.5+1x1.5 (1.8.1)

Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17)

S/F of G.I.Earth Plate Earthing 600 mm x600mmx6mm with Salt & Charcoal for Earth electrode (3:4)+(3.6)

S/L of 25mm x 6mm G.I. earth strip in ground(3:10)

Provision of Armoured cable size 4x6Squre Metersm (37) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 4x10Squre Metersm (38) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 4x16Squre Metersm (39) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Provision of Armoured cable size 3 1/2 x 35Squre Metersm (25) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Laying of MV cable upto 25Squre Metersm in ground (5.1.1)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm in ground (5.1.2)

Laying of MV cable upto 25Squre Metersm on surface (5.5.1)

Laying of MV cable above 25Squre Metersm to 120 Squre Metersm on surface (Horizontally)(5.5.2)

S/M of end termination of LV/MV cable size 3 1/2 x35 Squre Metersm (5.8.21)

Supply and Installation of 7 Meters long hot dip galvanized Octagonal pole having base dia of 175 mm and top dia of 70 mm and plate thickness of 4 mm or more complete with base plate and 4 Numbers Jtype En 8 grade foundation bolts M24X750mm to withstand 180 KM / HR wind speed considering the weight. O Lights at a height of 7 Meters above ground .Both the Octagonal pole, En8 grade fdn bolts and bracket must be manufactured in the Octagonal pole manufacturing company. ( Bracket & En8 grade Fdn bolts manufactured by third party pole supplier/manufacturer shall Numberst be acceptable). (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & Instalation of 7 meter HDG octagonal Pole shall be designed to withstand the maximum wind speed as per IS 875.(Top 70 mm & Bottom 130mm of 3 mm thick) The poles shall with average coating thickness of 70 micron.The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal weldingwith Four arms detachable ring type Bracket suitable to hold lights symmetrically. The Base Plate (225X225X16mm) with 4 Numbers of plinth Foundation bolts(20 mm dia 700mm Length) to be mounted on concrete Foundation (1.5'X1.5'X4' high) usng HYSD steel reinforced for errection of Pole firmly as per direction of Engineer in Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & Instalation of 7 meter HDG octagonal Pole shall be designed to withstand the maximum wind speed as per IS 875.(Top 70 mm & Bottom 130mm of 3 mm thick) The poles shall with average coating thickness of 70 micron.The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal weldingwith Single arms detachable ring type Bracket suitable to hold lights symmetrically. The Base Plate (225X225X16mm) with 4 Numbers of plinth Foundation bolts(20 mm dia 700mm Length) to be mounted on concrete Foundation (1.5'X1.5'X4' high) usng HYSD steel reinforced for errection of Pole firmly as per direction of Engineer in Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply & Instalation of 7 meter HDG octagonal Pole shall be designed to withstand the maximum wind speed as per IS 875.(Top 70 mm & Bottom 130mm of 3 mm thick) The poles shall with average coating thickness of 70 micron.The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding with two arms detachable ring type Bracket suitable to hold lights symmetrically. The Base Plate (225X225X16mm) with 4 Numbers of plinth Foundation bolts(20 mm dia 700mm Length) to be mounted on concrete Foundation (1.5'X1.5'X4' high) usng HYSD steel reinforced for errection of Pole firmly as per direction of Engineer in Charge. (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying and Fixing the following size medium gauge GI mast arm pole bracket for fixing the luminair on the existing pole structure of approved design including making suitable fixing arrangement, with supplying nuts , bolts etc i/c painting etc as reqd. 1.5 Meters channel T bracket suitable for pole top Dia 70Mm with provision of fixing 4 Numbers 200W floodlight .( The arm should be HDG and of same OEM)(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, installation, testing & commissioning of 90 watt / >=120 luemns per watt, IP66, IK 08 , with 10 Kv SPD additional SPD street light, compact and aesthetic aluminium powder coated housing with precise street optic lens similar to make Wipro LR22-132 Skyline Street Light complete as per direction of Engineer-in-charge(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying and fixing Allumium/Cast iron Decorative lighting pole with junction box to the luminaries completely. The pole should have in built loop in /out box with 6 Amps 10 KA SP MCB connectors suitable for 6 / 16 Squre Metersm cable termination complete with DIN bar, shooting Links, end lock,foundation with M20 grade concrete for the pole etc as required including terminations with insulated copper lug etc. of approved make including the cost of labor & material T & P as required as EIC(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supplying & fixing of Pure polyester UV resistant powder coated,die cast aluminium housing with polycarbonet clear diffuser post topincluding 30/35 watt LED lamp with Driver for outdoor installtion, LM-79-80 suitable for mounting on the mast/Pole/base with suitbale size copper wire/ lugs and sockets, earthing, including fixing , making connection testing commissiong etc as reqd(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

LED bush & spike luminair 6-8 watt with extruded alluminium housing and adjustable mounting bracket with lamp.(Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

Supply, Installation, Testing and Commissioning of LED Sports Arena Light with Max system power of 200W , CCT 5700K +/-355K as per ANSI , CRI>70, SDCM<3 , with Minimum delivered lumen of >30,000 lumens at 60 degree beam angle. The fixture housing must be Made of ADC 12 Pressure die cast Aluminium housing for rapid thermal healing & Powder coated by Corrosion resistant NaNumbers coating techNumberslogy. Luminaire must have minimum Ingress protection of IP66 and Impact Resistance of IK08. The light engine should use Metal Core PCB with high grade aluminium (AL5052) and should have a thermal conductivity of >2W/m.K. The fixture should be equiped with stabilized Injection moulded special PC lens optics ensuring low glare & best in class uniformity( Glass cover Numberst allowed). The light engine and the driver compartment should be thermally isolated by an natural airgap for better thermal management . Luminaire housing and optical compartment both should carry OEM's logo embossed / engraved (Numbers stickering is allowed). The luminaire must have Integral encapsulated high efficiency electronic thermally isolated constant current IP67 driver having a Aluminium extrusion construction with operating voltage range of 90-305V, power factor > 0.95, THD < 10%, Output Current Ripple at < 200 Hz (pk-pk) <2% , with Inbuilt surge protection of : DM 6kV, CM 10kV and upgraded with integrated External IP67 protected SPD of 20KV/10KA surge protection . Driver should have Over Voltage Protection, Short Circuit Protection, and Over Temperature Protection and should have output lumen compensation to maintain constant light output over the life of the LEDs .Weight of the Luminaire including cradle should be less than 5 Kg Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. CE Certified, ROHS compliant, BIS Certification for Luminaires & Drivers. All supporting documents like Technical data sheet of Luminaire & Driver, test reports including test reports photometry , TTC, IP, IK, Vibration and salt spray test from OEMs Own NABL accredited Laboratory. LM80 from LED OEM in 100% compliance with the specified luminaire technical requirements, shall be mandatorily submitted along with the bid. BIS of the Luminaire should carry the Own factory address of OEM, vendor facilities are Numberst acceptable(Mounted on existing 12Meters Mast 7 Meters Pole) (Make should be as per the approved quality and specifications. It should be approved by the user agency (Sports & YS Department) and the works should be executed as per the direction of Engineer in charge.)

1st Year Maintenance

2nd Year Maintenance

3rd Year Maintenance

4th Year Maintenance

5th Year Maintenance

Please Enable Macros to View BoQ information