Interior and Fit-out work for office space of MIL at J-101, 1st Floor, Tower- J, World Trade Centre, Nauroji Nagar, New Delhi-110029

BILL OF QUANTITIES (BOQ)

S.No. Sub-Head DSR Amount (in Rs.) DSR Ref. NoMultiplication factor DSR Amount (in Rs.) NDSR Amount (in Rs.)

3 E & M (except light fixtures and UPS system) 2,371,281.28 2022 0.973 2,307,256.68 7,667,606.39

4 E & M (light fixtures and UPS system) 589,480.00 2025 1.00 589,480.00 2,663,704.50

8 PLUMBING & FIREFIGHTING WORKS 810,801.13 2023 0.973 788,909.50 689,129.24

Grand Total (DSR+NDSR) 39,600,502.19 A

Grand Total (DSR+NDSR) 39,600,502.19 A

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

Summary of Civil and Interior Works

S.No. Description of Works Amount (SR, in Rs.)

2 Masonry & Plaster

3 Paving, Flooring & Wet Works

4 Partitions & Wall Cladding

7 Finishes & Miscellaneous

GRAND TOTAL (Carried Forward) 11,811,553.78

GRAND TOTAL (Carried Forward) 11,811,553.78

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

CIVIL & INTERIOR WORKS

2 MASONRY AND PLASTER

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement

concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland

Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:

9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the

cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following

grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 110% of the minimum specified cement

content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

4.20.2 All works above plinth and upto floor V level

4.20.2.2 Concrete of M15 grade with minimum cement content of 240 kg /cum cum 40.00 9,341.80 373,672.00

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC

blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with

approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-

Charge. (The payment of RCC band and reinforcement shall be made for seperately).

2.4 13.2 CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick wall of mix.

2.5 13.4 12 mm cement plaster of mix

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five

level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size).

2.7 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

2.8 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers SQM 4.00 736.40 2,945.60

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and

binding all complete above plinth level.

5.22A.4 Hot rolled deformed bars kg 60.00 107.85 6,471.00

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick POP Punning over

cement plaster in line & plumb finished smooth to receive paint. (Internal surfaces of walls).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of

cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be

2.11 22.5 allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with water SQM 36.00 617.05 22,213.80

proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints,

corners, junctions of pipes and masonry with polymer mixed slurry.

AAC BLOCK FILLING: Providing and Laying of AAC Block Filling in the Slab Sunk or Raised Areas as a Back fill

or platform. Laying should be done in layers with pounding done at every level to ensure a proper cavity

free installation without disturbing any existing services in the area. Cost to also include haunching for

plumbing pipes.

SUB TOTAL OF MASONRY AND PLASTER 756,876.10 131,792.00

3 PAVING, FLOORING AND WET WORKS

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified

by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of

3.1 8.31 any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of SQM 115.00 1,267.95 145,814.25

cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,

including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in

all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey

3.3 11.41A cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The

tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch

trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles

gently and easily.

11.41A.2 Glazed vitrified floor tiles polished finish of size

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be

specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours,

3.4 11.40 shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 SQM 30.00 1,439.40 43,182.00

Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement

and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

3.6 MR coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting

and finishing complete as per direction of Engineer-in-charge.

KITCHEN/ PANTRY/ HAND WASH COUNTER :- Providing and fixing pantry and toilets with Granite stone top

(with straight edge polished nosing) complete with base cabinet made of 20mm BWP board, outside

surface (shutters) finished in 1mm thick Laminate of approved shade. All internal surfaces to have

balancing laminate. The rate inclusive of necessary hardware, handle lock sets, self closing hinges, spring

loaded shutter, latch inside, all cabinet hardware complete as per Architects approval. (BR of stone to be

taken as Rs 1600/Sqmt). Width of work top counter 600mm/ detailed drawings.

Carpet- Supply and installation of modular carpet (including skirting and underlayer) of approved model

and shade and made with 100% nylon 6/6.6 tufted textured tiles of minimum 500mm x 500mm in size, stain

resistant, anti microbial, and having colour fastness to water, fastness to light, rubbing fastness and castor

chair suitability as per relevant standard for heavy commercial usage, with 100% PVC free Wellbac

3.8 MR Function Backing with having average density 6000 oz/cu. yd. or more,Nominal total thickness of 5.9mm, SQM 35.00 2,160.00 75,600.00

and Pile weight – 16-18 oz/ sq yard. Material shall be CRI GREEN LABEL PLUS certified, and shall have

recycled content complying to GRIHA requirement, including fixing with GRIHA compliant adhesive of

approved make, minimum 15 years manufacturer's warrantee, all complete as per drawings,

manufacturer's specifications.

ALUMINIUM SKIRTING: Supply & fixing of 75mm Aluminium Skirting with 15 micron anodising In Natural Finish.

3.8 MR Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC RMT 125.00 360.00 45,000.00

Jointers and Gasket.

Supply and fixing of subway tiles as per selection on walls. Tiles shall be set with adhesive of thickness

required to achieve plumb and 90 degrees on all surfaces.

Providing and fixing removable raised/false access flooring with system and its components of approved

make for different plenum height with possible height adjustment upto 50 mm,comprising of modular load

bearing floor panels supported on G.I. rectangular stinger framework and G.I. Pedestal etc. all complete,

as per the architectural drawings, as specified and asdirected by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI

fully threaded stud 16mm outer diameter with two GI

Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head

in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using

epoxy based adhesive of approved make or the machine screw with rawl plug.

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm

thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded

screws ensuring maximum lateral stability in all directions, the grid

formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide

adequate solid, rigid support for access floor panel, the system shall provide a minimum clear

uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all

complete as per the architectural drawings, as specified and as directed by

the Engineer-in-charge

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome

and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection

and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland

cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished

with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion

and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on

area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The

panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of

50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-

charge. All specification must be printed on the side of the panel to ensure the quality of the product.

11.54.1 300 mm Finished Floor Height (FFH) SQM 12.00 5,623.95 67,487.40

ENGINEERED WOOD FLOORING:Providing and Fixing of Compct ENGINEERED WOODEN FLOORING Panel

12.5x145 x 1820 Total thickness 14 mm Numbers of panels per pack 6 Nested Lengths Max. 1 plank out of 6

m2 per pack 1,583 m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3 mm Core

board PEFC controlled sources Spruce Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue

and groove Length Uniclic Width Uniclic Multifit Domestic use Conditions in each pack 33 years Uniclic -

Multifit connection Lifetime Commercial On request "Wood for Life" Edge Protect + Provides a warranty on

build-up of residue dirt along the edges due to maintenance over the years 10 years "Wood for Life"

Surface & Edge Protect + (lacquered products only) Provides a warranty on pollution of surface structure

3.10 MR and a warranty on build-up residue dirt along the edges due to maintenance over the years 10 years SQM 70.00 5,600.00 392,000.00

Surface layer Wood species Oak Origin Europe Finishing UV cured Oiled finish 2 layers UV cured Lacquer

Anti-scratch top coat 5 - 7 layers Natural variance Due to nature, visual surface can deviate from samples

Surface treatments cf catalogue/website Nature Marquant Vibrant General aspect of installed EN 13489

Lipping - difference in height (mm) ≤ 0,20 difference in width (mm) ≤ 0,20 cupping lengthwise % ≤ 0,1

cupping in width % ≤ 0,2 Dimensional stability ISO 24339 Cupping short side max % ≤ 0,30 Changes 30 - 85 %

RH Cupping short side min % ≥ - 0,20 Open joints short side (mm) ≤ 0,20 Open joints long side (mm) ≤ 0,30

Underfloor heating Suitable of special installation instructions.or its equivalent as per direction of Engineer

TOTAL FOR PAVING & WET WORKS 1,044,193.65 636,350.00

4 PARTITIONS AND WALL CLADDING

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height consisting of G.I. frame and

required board, including providing and fixing of frame work made of special section power pressed/ roll

form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling

channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the

spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable

4.1 9.105 anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm

and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and

placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along

both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at

spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry

wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing

and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners

(25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's

specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG)

plaster board conforming to IS: 2095:

Gypsum Panelling:-Providing and fixing, in position concealed G.I. section for wall paneling using board of

required thickness fixed on the ‘W’ profile (0.55 mm thick ) having a knurled web of 51.55 mm and two

flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one

flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm.

4.2 9.133 Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully

threaded self-tapping dry wall screws. Board is fixed to the ‘W’ profile with 25 mm countersunk ribbed head

screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-incharge, the joints of the

boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide

seamless finish.

9.133.3 Gypsum board conforming to IS: 2095 Part - I

GLASS PARTITIONING:- Providing & Fixing Full Height Glass partition using 12mm Thk. Glass with anodised

Aluminium frame fixing glass with snap on option consisting of top, bottom and side frame measuring 40-

46mm x 18mm-26mm complete with glazing rubber as per manufacturer's specifications and instructions of

4.3 MR Engineer- in-charge. Rate include supply & Installation of 12 mm thk toughened glass with double sided SQM 40.00 5,584.00 223,360.00

adhesive tapes for glass to glass butt joints. Partition system from FFL to False Ceiling level, inclusive of cost

of support required for fixing in the ceiling. The frame to be powder coated in desired shade as per the

instructions of the Architect.

PARTITIONING- Partition using 12mm HDHMR board fixed on both sides on aluminium Studs Frame 50mm x

4.4 MR 50mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm c/c SQM 180.00 3,354.00 603,720.00

horizontally and vertically. Aluminuim frame to be fixed to floor and RCC Ceiling using fastners.

PANELLING- Panelling using 12mm thick HDHMR board fixed on one side on Aluminium Frame 50mm x

4.5 MR 25mm x 1.5mm as per approved sample and architectural drawings placing the same 600mm c/c SQM 225.00 2,384.00 536,400.00

horizontally and vertically. Aluminium frame to be fixed to walls, floor and RCC Ceiling using fastners.

4.6 MR Cladding using 12mm thick HDHMR board on existing frame/ surface. SQM 10.00 1,370.00 13,700.00

VEENER CLADDING- Providing and Fixing 4.0 mm thick decorative/ Natural Veneer of approved design and

shade , cladded on to existing partitioning. (base rate Rs. 1450/- sqm)

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade

texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180

nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd

coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove

excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with

4.8 13.116 special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry SQM 89.00 3,049.85 271,436.65

for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet

rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede

4.9 9.127 finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality.

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing and fixing of 4mm thick MDF on existing frame, GRG board, HDHMR board, Gypsum board with

4.10 MR the necessary screws, fixing arrangements, as per design and detail. The cost to include making in grooves SQM 400.00 794.00 317,600.00

of size and design as specified by the architect including fixing accessories complete.

Providing and fixing of 1.25mm thick laminates (as per IS:2046-1995, DIN EN 438, NEMA LD3-2005 quality

standard), made out of urea free thermosetting resign treated Kraft as core material and design paper as

a finish surface. water boiling test reflect the water immersion through permissible increase on thickness

and mass <0.60% , Laminated should accomplish Antibacterial properties ( under JIS Z2801:2000,

manufactured under EN438-2&3:2005 standard). The item to include proving and fixing of base of 4mm

thick MDF with/without grooves as per appproved design.

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183,

having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw,

rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of

Engineer-in-Charge.

Providing and fixing of Zinc reception backdrop panel made out of 18mm thick commercial plywood and

12mm thick clear acrylic sheet pasted below 1.0mm thick CNC cut Perforated Zinc titanium alloy in

approved design and shade. The cost to include all necessary support subframe, finishing of edge and

crimping of zinc sheet to cover the subframe in all respects. The cost to include making all necessary

provisions for adding strip light at the back (strip light to be paid seprately). complete as per approved

drawing and design by the architect/ engineer-in-charge.

Supply and installation of VMT Fabric Fluted 12mm PET panels which shall be processed with VMT

technology for surface customised colour options with fabric pattern/ or as approved as per the designers

requirement, the panel shall be made from -100% polyester fiber, with up to 70% recycled Fiber. size of

panel 2800mm x 1200mm (± 0.5mm). Panel Should be mostiure resistant and also Non-toxic, non-irritant,

and fire-resistant complying with safety standards confirm to Class 1 Fire Ratings tested as per BS 476 Part 6

(Fire Propagation) & Part 7 (Surface spread of flame) ,ASTM E 84 CLASS A, EN 13501 PART 1C,2S for interior

applications. Noise reduction coefficient (NRC) - 0.3 with direct fix method, 0.85 with 25 mm gap with infill,

0.95 with 50 mm gap with PET WOOL infill. The product should be 100% make in india and OEM must have

ISO CERTIFICATIONS- complying to- IGBC Membership ISO 14184-2 (Release formaldhyde)

ISO 9001 (Quality Mangement System)

ISO 14001 (Environmental Management System)

ISO 45001 (Ocupational helth & safety management system)

The cost to include advesive and/or any other accessory required for fixing complete as per instructions

of engineer - in -chage

SHELVES:- Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or

graded wood particle board IS : 3087 marked, with one side decorative and other side balancing

lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever

required, edges to be painted with polyurethane primer (fittings to be paid separately).

LAMINATED STORAGE CABINET FOR GENERAL STORAGE- Out of 19mm Commecial Ply Board finished using

1mm thick Laminate. The storage to be complete with all hinges, drawer glides and hardware from

4.16 MR approved make. All internal surfaces to be completed using balancing laminate. Including brass D-type SQM 20.00 10,250.00 205,000.00

handles for shutters and recessed type handles for drawers or as approved. Storage to be of all heights as

per design. Storage shutters to be made in solid laminate/ glass as per design and drawings.

DISPLAY SHELFS - Out of 19mm Commecial Ply Board finished using 1mm thick Laminate. The cabinet to be

4.17 MR complete with all hinges, drawer glides and hardware from approved make as required. All internal SQM 5.00 9,800.00 49,000.00

surfaces to be completed using 1mm laminate. Storage to be of all heights as per design.

Providing and fixing in place display cabinet made out of exposed 25 x 25mm MS frameworks and 12mm

thick plywood shelfs. The cost to include painting of MS works in duco paint of approved shade and

cladding of all plywood faces in approved shade and design of laminate. The overall size of cabinet shall

be upto 2.4m in width, 3.0m in height and 0.45m in depth complete as per design.

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

STORAGE CABINET FOR ELECTRICAL PANEL AND VOLTAGE STABLIZERS- Cabinet Shutters out of 19mm

Commercial Plybaord finished in 1mm Laminate of base cost Rs. 380 per sqmt. Shutters to be fixed to a

frame. Rigidly fixed on both sides and top finshed in laminate. No internal carcass required. All Hinges of

hettich or equivalent. Internal Surface of the shutter in balancing white laminate. All shutters to be provided

with Stainless steel louvers at the top and bottom of the shutter as per the site requirements and instrcution

of the Engineer In charge.

SUB TOTAL OF PARTITIONS AND WALL CLADDING 452,822.15 3,150,526.68

GYPBOARD CEILING :- Providing and fixing false ceiling at all height including providing and fixing of frame

work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm

each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

Including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering

upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction

of the Engineer in Charge but excluding the cost of painting with :

a) 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I SQM 410.00 1,355.80 555,878.00

TRAP DOOR :- Providing and fixing trap door in false ceiling made of "Novapan "pre-laminated board with

5.4 MR hardwood framing, dead locks, lapping all around including all hardware, hinges etc. complete as per SQM 5.00 3,098.17 15,490.87

design and drawing.

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and made hardwood

5.5 MR framings hung from ceiling @1000mm centre to centre with 1 nos of 12mm thk. Commercial ply on vertical RMT 22.00 1,161.00 25,542.00

& 12mm thk. Commercial ply on horizontal surface (straight & curved). Inclusive of finishing in Paint.

WOODEN VENEER CEILING :- Providing and fixing wooden veneer ceiling by Fixing Natural Teak Veneer on

12mm Underlay commercial Ply fixed to a subframe made using 50mm X 50mm Kiln seasoned and

5.6 MR chmeically treated hollock wood fixed to RCC ceiilng using Fastners . The cost to inlcude the finishing of the SQM 20.00 6,756.00 135,120.00

Veneer using wood stain and clear coat of PU (Gloss/ Matt) as per the instructions of the Engineer In

Charge. (base rate Rs. 1450/- sqm)

Providing the gypsum single sided cove of 150mm x 150mm having a facia of 75mm to macth the

specifications same as gypsum ceiling.

Providing the wooden cove of 150mm x 150mm having a facia of 75mm to macth the specifications same

GYPSUM BOARD VERTICAL BAND- upto100mm high gypsum band all round the mineral fibre/ gypsum

5.9 MR ceiling. In order to make the Mineral Fiber/ gypsum ceiling higher than the Gypsum Ceiling by upto 100mm RMT 40.00 372.00 14,880.00

as per drawings. (visible surface of gypsum band to not exceed 100mm) including plastic emulsion paint.

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Providing and fixing ceiling system formed as an open metal ceiling with an open area of more than 50%.

The multidirectional ceiling composed of equilateral triangles 600mm modules with perfectly

homogeneous aspect and the im-pression of a uniform assembly. The main blades comprising 100mm

height & 25 mm width interlocked polylams in Extruded aluminium 1.50mm thickness compensating

tolerances in x and y direction. The substructure consists of a form punched perforated profile [U1040] as a

lateral grid which is suspended from the ceil-ing with nonius adjustable upper and lower parts or with

5.10 threaded rods using official approved dowel plugs. The grid profiles are to be connected together at the sqm 95.00 23,510.00 2,233,450.00

ends by means of longitudinal connect-ors [U 1041] [screw fasteners]. The spacing of the grid profile is

according to the requirements of DIN EN 13964. On profiles angles, C-band raster as secondary profiles are

bolted on by means of C channel hanger bracket with M6 bolts. Only construction parts ap-proved by the

manufacturer may be used. Provide necessary supports, provisions as per the architects / PM’s Instructions.

Toler-ances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2008 approved by TUV.

Finish of ceiling is in wood Finish powder coated with minimum 60 microns paint thickness

SUB TOTAL OF CEILING 555,878.00 2,450,298.59

6 DOORS/ WINDOWS

35MM THICK VENEER FLUSH DOOR WITH FLOOR SPRING- 35mm thick flush Doors of size upto 2400mm x

1050mm complete with Hardware including floor spring, Door Closer, dead Lock with inbuilt key, D-Handle

etc. including cost of teak lipping all around with melamine/ duco finish. The item to include installation of

all kinds of latches as per the requirement. (BR of veneer to be taken as Rs 1450 per sqm)

DOOR FRAMES- Providing wood work in frames of doors, windows, clerestory windows and other frames,

6.2 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (

hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood CUM 0.25 142,949.70 35,737.43

LAMINATED FLUSH DOOR- Flush Doors finished using 1mm Thick Laminate on both sides panel of size upto

2400mm x 1000mm complete with Hardware including hinges, Door Closer, Mortice Lock with Handle,

latches etc. including cost of Door frame with melamine/ duco finish. The cost to include providing and

fixing of vision panel as per design.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts

6.4 9.53 and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse EACH 36.00 228.85 8,238.60

sand : 6 graded stone aggregate 20mm nominal size).

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door stopper with necessary

screws, etc. complete.

FIRE DOOR- Providing and fixing single leaf 120min Rated Fire Door of size 900x2400. with vision panel using

wired glass complete with Fire proof door frame. One side to be finished in fire retardant paint and one side

to be finished in Laminate of approved shade. All Frame to be finished in fire retardant paint. All hinges and

hardware to be thermatically sealed and 120 mins fire rated.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and

manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and

making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-

Providing and fixing of SS 1200mm long D handles to glass/ flush door in approved shade and finish

including all required fitting complete as per instructions of engineer-in-charge.

Providing and fixing of SS bottom patch lock on glass doors in approved shade and finish including all

required fitting complete as per instructions of engineer-in-charge.

Providing and fixing of SS half moon stopper with rubber bumper in approved shade and finish including all

required fitting complete as per instructions of engineer-in-charge.

SUB TOTAL OF DOORS 60,407.69 515,247.39

7 FINISHES & MISCELLANEOUS

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre SQM 450.00 73.95 33,277.50

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

7.2 13.83 Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete.

Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer using structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works kg 50.00 172.60 8,630.00

7.5 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

13.61.1 Two or more coats on new work SQM 100.00 155.90 15,590.00

HONEYCOMB BLINDS -Original Non-woven honeycomb shades having soft fabric appearance and high

energy-efficient fabric with high tear strength constructed out of Anti static, anti-UV, damp proof, resilient,

colour fast & Sanitized Treat 100% spun bonded non-woven polyester fibre & precision manufacture to form

a hexagonally shaped cell . Cell size 3⁄4”Honeycomb structure with dis􀆟nct air pocket for energy efficiency

and increased insula􀆟on. Shadings are single tone facing both exterior and interior .Being a Low shading

co-efficient will have following Comfort rating & solar optical properties. Aluminium profile should have

temper WP consisting of alloy 63400 along with anodizing of 10 micron and powder coating of 60 micron.

The tensile strenghth of profile should be 9.10 Kg/mm square and elongation 18.The control clutch drive

unit engineered heavy duty chain drive pulley operating system consisting of gear clutch housing and

locking plug containing minimum 6 ribs and inserted at minimum of 38mm into roller tube. It is self-

lubricating Exclusive clutch with safety pins for secure bracket installation and unlocking pin for quick

manual removal. Universal clutch is most convenient for large windows down to the smallest windows. It

shall be driven by a ball chain pulley with ball chain and can be positioned at Right hand or Left hand side

of the shade. Clutch gear ratio of 1.75:1 for reduced operating force on larger blinds.. Mounting hardware

brackets universal brackets including end plug bracket with lock down retainer device. Brackets finish of

powder coated metal installation brackets made of stamped and hardened steel. Roller tube circular-

shaped aluminium tube extruded from alloy 63400 and temper WP. Bottom rail flat-shaped extruded

aluminium from alloy 63400 and temper WP. Ball chain shall be 2mm diameter cord with plastic balls

moulded to form an endless ball chain. It is used for raising or lowering action of the shades. Plastic parts all

plastic components are UVstable compounds available white.

ZEBRA BLINDS -Providing & fixing of Twist Window Shadings Blinds as per the sample shown having room

darkening fabric strip and sheer fabric strips alternately in such arrangement as when light filering strips

overlap each other, it creates visibilty and once the light filtering strips overlaps the sheer ones, it creates

the no visibility effect.It has bottom rail made of aluminium alloy extruded profile, powder coated and

provided in fabric coordinated colour. The rolling tube should be made up of aluminium alloy from

extruded profile of Ø34mm. The fabric of this Blind should be made up of 100% anti-static polyester vanes

7.7 M.R. having light filtering and sheer vanes to reduce glare. Sheer layers made of white 100% knit polyester & the SQM 35.00 8,673.00 303,555.00

selection of colors, textures and opacities as per Engineer-in-charge. The FABRIC shall be constructed from

spun-bonded 100% polyester fiber, having Green guard Certification treated with soil & dust repellant

require minimum regular interval cleaning. The fabric has a maximum width of 2.80 M and a thickness of

0.38mm (+ 5%) and having weight of 272g/m2 (+ 5%).The strip size is Solid 8.5 cm / Sheer 6 cm. The shading

to be operated by Easy rise mechanism with a continuous cord loop operating option. All plastic parts are

in white color. Installation to be done by quick release brackets (wall or ceiling).

Providing & fixing decorative Poly décor fabric Wall Paper (on walls and ceiling) of weight 475 g /sqm as

7.8 MR per approved shade & design including prepration of surface with 2 coats of Nubin Glue based epoxy SQM 20.00 3,695.00 73,900.00

Providing & fixing custom printer, as per approved design, decorative Poly décor fabric Wall Paper (on

7.9 MR walls and ceiling) of weight 475 g /sqm as per approved shade & design including prepration of surface SQM 40.00 4,650.00 186,000.00

with 2 coats of Nubin Glue based epoxy quote.

Digitally signed by RAJ PAL

S.No. DESCRIPTION UNIT QTY RATE AMOUNT MARKET RATE AMOUNT

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface with 15 yrs MCS warranty

as approval of the Architect. (Only film surface area shall be measured and paid).

Reception Table:-Providing & Installation of Reception table of of size upto 2.4m x 0.90m x 0.75m/ 1.2m (ht),

made out of 19mm thk. Commercial Board finished in Acrylic Solid Surface of approved shade and colors

complete as per design. The front surface of the table shall be tapered as per approved design. One (1)

number Drawer pedestal with 3 lockable drawers and channels (all hardware from Hettich) to be provided

under the table to be finished in Solid Acrylic surface. All visible surfaces to be finished using Acrylic solid

surface as per details.

Conference Table - Providing & Installation of Custom made rectangular shaped Board Room Table

complete as per design having straight/curved edges out of the overall size of upto length 4.0 m, ht .

0.75m, width 1.5 m, in 19mm thk. Commercial Board. Base to be made out of powder coated MS members

as per design and shade. Table top to be made in 19mm thick commercial board and finished in 12 mm

thick acrylic solid surface of approved pattern and shade having edge of 50-75mm thick tapered edge on

all sides.Cable tray to be provided under the table top. Snake cable manager to be provided for taking of

cables form floor junction box to table top. The cost to include making of cut outs necessary for electricity

Preparation of complete set of shop drawings, services drawings, finishing, detailing and development of

7.13 M.R. design 2D/3D views, walkthrough and for supervision of all works including details. A qualified professional Percentage 1.00% 39,325,802.83 393,258.03

for the purpose shall be appointed after due appproval from Engineer In Charge.

Providing and fixing of 5-6 mm thick annealed GRIHA rated lacquered glass manufactured industrially by

curtain coating process with PU lacquer (50 micron thick), opaque (if viewed against a support wall)

conforming to EN 16477 standards for back painted glass , of approved color by Architect/ Client fixed with

compatible Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of

10 to 30 mins compatible for installation of mirror and lacquered glass / Foam based double sided

adhesive tape for instantaneous adhesion, compatible with mirror and lacquered glass having Shear bond

strength (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water proof marine plywood /

MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. The contractor should

submit test reports for backpainted glass from manufacturer - High humidity Resistance (conforms to BS EN

1036 1999); Color fastness ISO 105B02 standard & Mechanical Resistance ISO 7784 ( Taber Abrasion test )

ISO 2409 ( Cross Hatch Test ) standard The manufactured backpainted glass should be environmentally

friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post

industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float

Providing & fixing 12mm Thick. 100% Acrylic solid surface of approved make and colour using approved

Adhesive to 12 mm thk. Waterproof Plywood of approved brand as per shape, pattern & details given in

7.15 M.R. the drawing. The rate includes providing & fixing beading, cutting, scaffolding, nails, all materials, labour, SQM 5.00 14,168.00 70,840.00

lead, lifts, HOM etc., complete.-for Lift Cladding. (The make, Shade, pattern etc., to be approved by

SUB TOTAL OF FINISHES 161,162.50 1,895,999.03

Digitally signed by RAJ PAL

BOQ FOR FURNITURE WORKS

S.No. Item Specifications Qty Price Amount Ref. Image

Providing and Placing Main TAble of Size upto 3000x2550x740.MAIN WORKTOP Size 3000x1050x740, ERU 1500x600x610mm-

Main worktop - Made of 43mm Thick (±1) combination of MDF and particle board with top veneer face coated with

clear lacquer. All edges are edge banded with matching 1mm thick veneer lipping.LEATHER PAD:Made of 18mm Thick

(±1) MDF with Leatherette wrapped around top surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top

panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board with top

veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining

construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with

leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit

is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm

Thick (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All thickness edges

are edge banded with matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2

grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC

lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to

IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty is fitted with aluminum

trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is fixed with soft closing hinges

and handle is provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER

BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB power points, 1 HDMI connection, 1

inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

Providing and placing High Back chair.SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass

filled poly-amide. Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density

45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE: 45.5cm. (D) x 52.4cm. (W) 2.

BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic Inner. *HIGH

BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body &

all other adjustment are provided in adjustable arm top sub assembly. · Up-Down adjustment has 8 position (10.5±0.5cm

range) · Arm top swivel adjustment- 2 position, 12°±2° swivel inside · Arm top width adjustment - Any position (2.0±0.5cm

range each arm top) · Arm top To - Fro Adjustment- any position (4.0±0.5cm range) · Armrest top is made up of high

density PU molded over glass filled Poly-amide inner. MECHANISM: The adjustable tilting mechanism is designed with the

following features: · 360° revolving type. · Forward tilt of sesat and back. · Upright tilt lock. · Tilt tension adjustment can be

operated in seating position. · 3-position Tilt limiter. . SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the

seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting

position. Seat depth adjustment range is of 5.0±0.5 cm. 6. ADJUSTABLE BACK SUPPORT: Back Assembly is connected to

buff polish die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting

position. It can be adjusted in the range of 7.5±0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height

adjustment has an adjustment stroke of 13.0±0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing

finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia.TWIN WHEEL CASTOR: 5 Nos.

twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.5±0.1cm wheel Diameter and

assembled to pedestal.

Providing and placing mid back Chair .SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass

filled poly-amide. Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density

45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE: 45.5cm. (D) x 52.4cm. (W) 2.

BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic Inner.MID BACK

SIZE: 50.5 cm. (W) x 61.8cm. (D) Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all

other adjustment are provided in adjustable arm top sub assembly. · Up-Down adjustment has 8 position (10.5±0.5cm

range) · Arm top swivel adjustment- 2 position, 12°±2° swivel inside · Arm top width adjustment - Any position (2.0±0.5cm

range each arm top) · Arm top To - Fro Adjustment- any position (4.0±0.5cm range) · Armrest top is made up of high

density PU molded over glass filled Poly-amide inner. MECHANISM: The adjustable tilting mechanism is designed with the

following features: · 360° revolving type. · Forward tilt of sesat and back. · Upright tilt lock. · Tilt tension adjustment can be

operated in seating position. · 3-position Tilt limiter. . SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the

seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting

position. Seat depth adjustment range is of 5.0±0.5 cm. 6. ADJUSTABLE BACK SUPPORT: Back Assembly is connected to

buff polish die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting

position. It can be adjusted in the range of 7.5±0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4

pneumatic height

adjustment has an adjustment stroke of 13.0±0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing

finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia.TWIN WHEEL CASTOR: 5 Nos.

twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.5±0.1cm wheel Diameter and

assembled to pedestal.

Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented Durable and

ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aesthetics

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply

4 Sofa 3 seater cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity 1.00 91,721.40 91,721.40

and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Providing and placing sofa of size 1060mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery - Pigmented Durable and

ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the aesthetics

S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid wood frame with ply

5 Sofa 1 seater cross section which is moisture , termite and borer resistant. Adequate treatment of wood initiated to enhance longevity 1.00 55,176.80 55,176.80

and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board 3mm , webbing 2 inch , Zigzag Spring - 3.8mm

Comfort- The seat is made of soft foam of density 28 kg/m3 which enhances comfort and cushioning with sinking feeling.

Ground Elevation- Equipped with legs, the sofa is elevated to allow a level of ground clearance.

Providing and placing in position Centre Table having a size of : 1000mm(L) x 600mm(D) x 425mm(H). Understructure of the table

which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without

knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm

thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H.

Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral

pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts,

wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge.Complete all as per the direction of

Engineer in Charge.

Providing and placing in position Corner Table having a size of : 500mm(L) x 500mm(D) x 425mm(H). Understructure of the table

which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without

knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm

thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H.

Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral

pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts,

wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge. Complete all as per the direction of

Engineer in Charge.

Providing and placing in position of main table of main table with overall size of table 1650 x 1650 x 750mm. The main

table shall be of size 1650 x 750 x 750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF

– one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing

access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC

8 membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and 1.00 77,314.78 77,314.78

approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top

pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.

Pedestals are provided with lock for security.

Providing and placing in position back unit.The Back Unit shall be of dimensions 1650 x 500 x 750mm. It shall be made of

25mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to

top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge

banded with matching 2 mm thick PVC lipping. Shutters are made of 25mm thick MDF one side pre laminate board with

0.4mm PVC membrane pressed on top. Shutters have a soft closing & anti slam mechanism. Handles are provided for

ease of opening. Storage is provided with lock for security.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of

back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree

revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more

comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of

die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene.

The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium

back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded

polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to

back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair -

75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to

max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of

back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanim shall be Active Bio Synchro Mechanism. The mechanism of chair shall have following features:360 degree

revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more

comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of

die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene.

The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium

back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from

pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/- 1

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 2400 Width mm x 900 mm

Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and

final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty

panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener

and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height

Director Main and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener &

Table final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF

board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on

either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage

shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall

be 25mm.The product should be AIOTA certified.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO 18001:2007

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer

and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density

= 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D.

The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03

cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be

moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type

tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The

Main Chair armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the

13 (director & following features : 360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support 2.00 50,022.56 100,045.12

conference room) ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of

variable tilt angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth

adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T

spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the

pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos.

of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm. Seat

height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic

inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and

hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be

cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128

cm, upholstered with pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with

pure leather and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-pivot for tilt with

feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated

conference room)

in seating position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be integrated in

the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected

to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable

back support to suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal

shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm

wheel diameter and assembled to pedestal.

Overall Size :Width : 182cm Depth : 92cm Height : 89cm Seating Height : 47.5cm THREAD : Nylon . Material Handling Data Sheet

15 Sofa 3 Seater (MSDS) for Glue 1.00 78,708.36 78,708.36

Standard of Plywood used: IS 303 Commercial Plywood , Thickness 12mm

Overall Size :Width : 182cm Depth : 92cm Height : 89cm Seating Height : 47.5cm THREAD : Nylon . Material Handling Data Sheet

16 Sofa 1 seater (MSDS) for Glue 1.00 51,701.70 51,701.70

Standard of Plywood used: IS 303 Commercial Plywood , Thickness 12mm

Providing and placing in position Centre Table having a size of : 1000mm(L) x 600mm(D) x 425mm(H). Understructure of the table

which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without

knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm

thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H.

Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral

pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts,

wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge.Complete all as per the direction of

Engineer in Charge.

Providing and placing in position Corner Table having a size of : 500mm(L) x 500mm(D) x 425mm(H). Understructure of the table

which includes Legs, top wooden frame & bottom tie members are made out of first quality rubberwood of approved make without

knots &defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. Top: 8mm

thick toughened glass of approved make. Construction: Knock-down assembly.Wooden members are PU painted with hardness-2H.

Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral

pattern on bottom surface 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts,

wooden dowel, plastic leg bush. Complete all as per the dimension of Engineer-in-charge. Complete all as per the direction of

Engineer in Charge.

Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x 750mm.

The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work

surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with

0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming

19 to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board 1.00 133,460.36 133,460.36

of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts

made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-

BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft

closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The Back Unit shall be of dimensions 2350 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

20 Back Unit thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC 1.00 61,031.96 61,031.96

lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is

provided with lock for security.

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm

Seat Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W

cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular

armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is

height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360°

21 Main Chair revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt 1.00 25,305.10 25,305.10

tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the

chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back

frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Providing and Placing Mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W

cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular

armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is

height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360°

22 Visitor Chair revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt 3.00 23,616.52 70,849.56

tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the

chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back

frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Providing and placing 2 seater sofa of size of size 1680mm(L)x945mm(D)x930mm(H)Solid Wood Frame.The sofa frame is

made from seasoned solid wood that undergoes multi-step treatment for protection against termites and bugs.

Synthetic Leather Upholstery Upholstery used is of high quality synthetic leather which requires little maintenance. All you

need to do is use a piece of cloth to gently wipe the surface. It is resistant to cracking and easy fading increasing the

sofa’s durability.

23 Sofa 2 seater High Grade FoamThree layer of super soft foam is put together with a layer of recron which offers a sinking feeling with 1.00 42,573.22 42,573.22

floating comfort to create comfortable seating for long hours Anti-Sagging Nylon webbing of 2 mm thickness prevents

the foam from sagging as it ensures superior bounce back when the weight is removed from the seat.

Ergonomic Support Back rest of the sofa is designed ergonomically to provide an additional lumbar support to keep your

back in its perfect position. The extended angular head cushion provides adequate headrest and enables correct body

posture for long seated hours

Providing and placing 2 seater sofa of size of size 1155mm(L)x945mm(D)x930mm(H)Solid Wood Frame.The sofa frame is

made from seasoned solid wood that undergoes multi-step treatment for protection against termites and bugs.

Synthetic Leather Upholstery Upholstery used is of high quality synthetic leather which requires little maintenance. All you

need to do is use a piece of cloth to gently wipe the surface. It is resistant to cracking and easy fading increasing the

sofa’s durability.

24 Sofa 1 seater High Grade FoamThree layer of super soft foam is put together with a layer of recron which offers a sinking feeling with 1.00 31,021.02 31,021.02

floating comfort to create comfortable seating for long hours Anti-Sagging Nylon webbing of 2 mm thickness prevents

the foam from sagging as it ensures superior bounce back when the weight is removed from the seat.

Ergonomic Support Back rest of the sofa is designed ergonomically to provide an additional lumbar support to keep your

back in its perfect position. The extended angular head cushion provides adequate headrest and enables correct body

posture for long seated hours

Provding and placing centre table of size 1200mm(L)x594mm(D)x411mm(H).Ultra-modern combination of wood and glass,

specifically shaped and engineered to give it stability. Now, your drinks won’t spill as easily in case of accidental tugs and yanks. •

The Wenge finish of the coffee table is done with utmost care, making it a posh addition to your space. • Has multiple compartments

to store books, magazines, or place decor items. A hidden

compartment within can be used to store utility bills and keys. • Good ground clearance enables

Providing and placing Side table of size 600mm(L)x600mm(D)x450mm(H). Designed for the modern minimalist with a need for handy,

26 Side Table compartmentalized storage. • Tabletop of durable, toughened glass with a digitally back-printed Skyline pattern creates a sleek, 1.00 11,606.48 11,606.48

modern look. • A strong, knockdown construction built for longevity.

Providing and placing in position of main table of main table with overall size of table 1800 x 2100 x 750mm. The main

table shall be of size 1800 x 900 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick

MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft

closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of

25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to

top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm

27 Officer Main Table PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade 1.00 77,314.78 77,314.78

and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top

pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.

Pedestals are provided with lock for security.

Providing and placing in position back unit.The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of

25mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to

top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge

banded with matching 2 mm thick PVC lipping. Shutters are made of 25mm thick MDF one side pre laminate board with

0.4mm PVC membrane pressed on top. Shutters have a soft closing & anti slam mechanism. Handles are provided for

ease of opening. Storage is provided with lock for security.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of

back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree

revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more

comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of

die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene.

The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium

back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly propylene) with moulded

polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to

back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair -

75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat height - min 45.5cm to

max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of

back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which is

connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanim shall be Active Bio Synchro Mechanism. The mechanism of chair shall have following features:360 degree

revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should ensure more

comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The chair shall be

provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of

die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm

pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene.

The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium

back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from

pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/- 1

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made

of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Providing and placing in position Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened glass UV

glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202

grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm,

height=35.1 cm.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane

foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility

just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers

impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped

33 Reception Chair spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form 1.00 13,847.30 13,847.30

the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be

adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The

adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors.

The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Providing and placing in position of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The

seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made

Reception Sofa 3 of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

Seater upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with

Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made

Reception Sofa 1 of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr,

Seater upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood

(which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and

surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning

effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-

36 Centre Table 12823:1990, Edge banded with matching 2 mm thick PVC lipping.Access Flap along with a Gromett is provided on work 1.00 15,508.74 15,508.74

surface for wire management.Wir

Providing and placing in position Corner table. The Glass shall be 10+/-0.3mm thick black tinted toughened glass UV

glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202

grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm,

height=35.1 cm.

Providing and placing panel & tile based modular workstation. Of size 1500 X 1500 (w) x 600 D with panel thickness of

52.4 mm thick and ht – 1200 including powder coated aluminum trims. Work top shall be pre laminate particle board

,`below the work top is also pre laminate particle board. The panel thickness comprises of 38mm (35 mm Minimum) thick

paper honeycomb + 3mm MDF on each sides + 3.6mm thick line gap each side+ 0.6mm decorative laminate or fabric

or lacqurered glass on both sides. Tiles: top tiles shall be fabric tackable or writing board or lacquered glass. Bottom Tiles:

38 Workstation it shall be of plain metal. Intermediate blocks shall be given of laminate. Wire Management - Wires shall be taken into 8.00 92,645.34 741,162.72

the system through cable ducts from the junction boxes and it shall be carried up to the panels through concealed

conduits inside the blocks. Partition panel between two workstation should be 52.4mm . Pedestals are top supporting with

leg, central locking of size 390 mm w x 435 mm d x 720 mm height 3dr = 2box+1file. The work shall be carried out as per

guidance and instructions received from engineer in charge. The product shall be Green guard BIFMA LEVEL, AIOTA,

GRIHA, SCS IAQ, GREENPRO certified. OEM shall be ISO 9001:2015, ISO 14001:2015 & ISO 18001:2007 certified.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane

foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility

just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers

impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped

39 Workstation Chair spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form 8.00 13,906.30 111,250.40

the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be

adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The

adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled

Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled

Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors.

The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

The overall dimensions of the top shall be 1200mm x 900mm x 720mm. The Worktop is made of a 25mm thick MDF OSR

with PU painting on top side. Understructure: It should consist of an inner tube assembly with top plate, for worktop

mounting, & an outer tube assembly with round/square bottom plate. The inner and outer tube asemblies are

telescopically connected. The top plate is made of 5mm thk HOT ROLLED steel plates (HR) (As per IS:2062) & the bottom

plate is made of 8mm thk HOT ROLLED steel plates (HR) ( As per IS: 2062). The inner tube assembly is made of dia 82.5 X

40 Café Table 2thk ROUND ELECTRIC RESISTANCE WELDED tubes (ERW) ( AS per IS:7138) and 8mm thk HOT ROLLED Steel plate (HR) (As 4.00 24,662.00 98,648.00

per IS:2062) welded together using tungsten inert gas welding. The outer tube assembly is made of dia 89 X 2.5thk

ROUND ELECTRIC RESISTANCE WELDED tubes (ERW) ( AS per IS:7138) and 8mm thk HOT ROLLED Steel plate (HR) (As per

IS:2062) welded together using tungsten inert gas welding.The whole structure is EPOXY POLYSTER powder coated (DFT 40-

60 microns). The product has a KD construction. It is assembled using alloy steel hardware( Blackened and coated with

rust oreventive oil).

Providing and placing cafe tables of size 1200mm(L)x900mm(D)x1020mm(H). Swing legs a PDC (Swing leg corner PDC)

part made from Aluminum alloy, which is connected to the worktop and cross members.Swing leg can be offer in dual

color. Wire Management Single Power box with raiser (8M+3M & 8M+3M

Anchor Roma) with Soft closing dual access flap with brush.Worktop: 25mm thk prelaminated partical board with pvc

lipping."OEM shall be ISO-9001:2015, ISO-14001:2015, ISO-45001:2018, BIFMA and AIOTA certified. Product should have UL

greenguard,Bifma level 2 ,Green pro ,Griha ,SCS indoor avvantage gold.

Supplying and placing of chair of dimensions 635W x 630D x 800H mm. The seat height shall be 455mm.The back shell

shall be made of 15mm plywood panle connected using Brackets made from 3mm Hot Rolled Steel Plates . Steel

brackets are Epoxy Polyester Powder Coated. 25mm PU Slab -Stock foam is pasted onto both sides of the shell and

pinched together to achieve the radius along the periphery. It shall be upholstered in Leatherette. The seat cushion shall

be made using 50mm PU Slab-stock foam and is upholstered in Leatherette. It shall be held in place with Hook and Loop

tape stitched to its bottom side. The understructure shall be made of seasoned Tewak Wood finished witrh clear matt

coat of PU Lacquer. Undrstrucutre members shall be glued together using Epoxy Resin Based Adhesive. The shell is fixed

to the understructure using Alloy steel hardware (blackened and coated with rust preventive oil).

Providing and Placing Cafe hi stoolSEAT ASSEMBLY:Seat is leatherette upholstered cushion fitted to a seat tray. The

cushion is made of 1.2 cm of PU slabstockfoam. Slabstock foam glued to CRCA sheet of 0.12 cm (+0.01cm) thick and

upholstered with leatherette. The seat tray is made of CRCA steel of 0.25 cm thk (+0.01cm) as per IS:513.It is powder

coated with epoxy based polyster powder coating (40-60 microns).* SEAT CUSHION SIZE: 40.0 cm. (W) x 34.5 cm. (D) *

43 Café Stool TOP TRAY SIZE: 41.5 cm. (W) x 40.0 cm. (D).WOODEN UNDERSTRUCTURE: Understructure of bar stool is made of FS-certified 6.00 23,384.06 140,304.36

seasoned teak wood finished with a clear matt coat of PU lacquer. * UNDERSTRUCTURE SIZE: 48.6 cm (W) x 47.0 cm (D) x

6.88 cm (H).FOOT REST ASSEMBLY .Foot rest is made up of 01.6 cm ($0.02 cm) M.S. ERW tube (IS:71380). It is epoxy based

powder coating (40-60 microns). Additionally it is coated with abrasion resistance coating.

* FOOT REST SIZE: 40.3 cm (W) x 38.7 cm (D)

Audio Video System

S. No. Function Description QTY Rate Amount

Supply, Installation, Testing & Commissioning of Two-way, Ceiling-mount loudspeaker with back can.

Continuous Power - minimum 30 Watts or better, Sensitivity- minimum 89 dB SPL or better, Coverage Angle -

1.1 Ceiling Speakers 110° or better, Maximum Peak SPL - minimum 110 dB or better, Rated Impedance - 8 Ohms. Transformer 6 ₹ 24,050 ₹ 144,300

Tapping - 70V/100V(30,15,7.5watts) or better. Transducers - LF - mimimum 6.5-inch or better, HF- .86-inch

coaxially mounted with LF or better, Should include OEM supplied mounting brackets.

Supply, Installation, Testing & Commissioning of Quad Channel Class-D amplifier. Per Channel Power 60W

@8Ω/4Ω or better. Support for 70V/100V or more. Power Sharing or Bridge/Parallel modes for better power

Amplifier for Ceiling distribution. Frequency Response- 20 Hz – 20 kHz or better. Signal to Noise ratio -> 103 dB or better, Input

Speakers impedance - >10k, balanced or unbalanced or better, Front and Rear panel indicators for Power, signal (per

channel), limit / mute / protect etc. or better. Better to have Remote standby and Power saving features -

Supply, Installation, Testing & Commissioning of Open Architecture Digital Signal Processor with 4 Mic/Line

Input with Phantom Power and 4 Line Output. GPIO Ports - 8x8 or better. AEC channels - 8 or more with 200ms

tail length.Minimum 8x8 Dante channels and support for up to 64x64 Network audio channels via Dante

/AES67 or similar protocol. SIP Softphone integration for Audio conferencing. USB-B & C port supporting AV

1.3 Digital Signal Processor 1 ₹ 364,000 ₹ 364,000

USB Bridging for software or web-based conferencing applications emulating USB Audio (Speakerphone)

and USB Video (Camera) driver. 24 bit-A/D-D/A converters or better, 48 kHz Sample rate or better, Input

frequency response of 20 Hz to 20 kHz or better, Input dynamic range > 109 dB or better. RS232 Ports - 2 or

more. The processor should support Network amplifiers without any additional cards or accessories.

Supply, Installation, testing and commissioning of Ceiling Microphone tile with 26 or more no. of omni

directional microphone, coverage area : 55sq mtr or more, Dante connectivity : dual / redundant, POE

Ceiling Tile Microphone

1.4 enable (qty of microphone will vary as per the mentioned coverage area and built in micorphone), Lighting 1 ₹ 559,000 ₹ 559,000

Indication on all four corner, It should work on open control protocol software and compitable to monitor

with a single sofware for all the microphone in the campus etc complete required as per the specifications.

86" Intractive Panel ,Brightness : 450 nit, Multi Touch Point : 20 Points (Max.) Interface : HDMI (3), RGB (1),

Audio In (1), RS-232C In (1), RJ45 (1), USB 3.0 Type A(3), USB 2.0 Type A (3), Audio Out / Optical Output, Touch

USB (2), Screen Size : 65",Panel Technology : IPS Aspect Ratio : 16 : 9 Native Resolution : 3,840 x 2,160

(UHD),Contrast Ratio : 1,2000:01:00,Viewing Angle (H x V) : 178 x 178 ,Response Time : 8ms (G to G) ,Processor

2.1 Intractive Display 2 ₹ 520,000 ₹ 1,040,000

Hi3571560 Quad-coreA551,105GHZ, Android -11,Ram-4/8GB,Storage 32/64/128 GB,OPS CPU ARM Quad-core

Cortex-A53 1.4GHz RAM 2GB DDR3 Architecture 64-bit Graphic Engine ARM Mali T720mp2 Hard Drive/Internal

Memory (eMMC) 16GB USB USB 3.0 x 2, USB 2.0 x3 LAN 10/100 Ethernet Wi-Fi 802.11b/g/n/ac

VIDEO,SWITCHING & INTERFACE SYSTEM

Supply, Installation, Testing & Commissioning of Cable Manager with 1xHDMI and 1xUSB-C (Video), 1xRJ45,

3.1 Cable Manager for Table 2 ₹ 78,000 ₹ 156,000

1xUSB-A, 2 x Power sockets or better.

Supply, Installation, Testing & Commissioning of Wireless Presenter with HDMI and USB Ports. Should support

3.2 Wireless Presenter 1 ₹ 227,500 ₹ 227,500

Windows, Mac, iOS and Apple screen sharing with two simultaneous displays.

Supply, Installation, Testing & Commissioning of Network Video Streamer configured as Encoder. Minimum

Inputs – 1 x HDMI Input and 1 x USB-C or better. USB-C should supportsingle cable connectivity for Video

encoding, AV USB Bridging to provide conference camera video and AEC speakerphone audio driver for

Software based Video Conferencing (MS Teams, Zoom, GMeet etc.) and for charging the connected

AVOIP Encoder for device. Simultaneous Video encoding - Dual or more. Local Preview Output – 1x HDMI with Scaling or

3.3 Cable Mangers & better, HDMI audio embedding and de-embedding, Network Audio supported via Dante/AES67 or similar 3 ₹ 286,000 ₹ 858,000

Wireless Presenters protocol, Video Resolution – 4K60 4:4:4 or better. Power – PoE and AUX, Control Port – RS232 or better, USB-A

for HID Signal Routing. Mounting hardware should be included.

Note: Required hardware/accessories/expander with perpetual software license should be quoted to meet

the minimum specification to fulfil the requirements.

Supply, Installation, Testing & Commissioning of Network Video Streamer configured as Decoder. Outputs -

1xHDMI with scaling or better. Local Inputs – 1xHDMI and 1xUSB-C for local switching. Audio embedding and

deembedding, Network Audio supported via Dante/AES67 or similar protocol. Video Resolution – 4K60 4:4:4

AVOIP Decoder for

3.4 or better. Power – PoE and AUX, Control Port – RS232 or better, USB-A for HID Signal Routing. Mounting 1 ₹ 286,000 ₹ 286,000

hardware included.

Note: Required hardware/accessories/expander with perpetual software license should be quoted to meet

the minimum specification to fulfil the requirements.

VIDEO CONFERENCE

Supply, Installation, Testing & Commissioning of 4K Network PTZ Conference camera with minimum 12x

optical zoom & 80-degree horizontal coverage. Low Noise CMOS 4K image sensor with User-configurable

resolution and quality for IP streams (up to 1080p). HDMI resolutions up to 4K30 or better and SDI-3G resolution

up to 1080p60 or better. Image rotation controls to allow for inverted mounting using ceiling bracket.

Minimum Illumination - 0.5 Lux @ (F1.8, AGC ON) or better, Horizontal Rotation Range - ±170°, Vertical

Rotation Range - -30° to +90° or better, White Balance controls- Auto, indoor, outdoor, one-push, manual,

4.1 4K PTZ Network Camera 1 ₹ 487,500 ₹ 487,500

specified color temperature or better. Camera should be able to transmit video via network to USB endpoint

connected for video conferencing. Power – PoE & AUX. Shall include wall mounting bracket included.

Note: Required hardware/accessories/expander with perpetual software license should be quoted to meet

the minimum specification to fulfil the requirements.

CONTROL SYSTEM & ROOM SCHEDULING

Supply, Installation, Testing & Commissioning of Hardware or Software based control system with required

5.1 Control System ports to control the devices mentioned in BOQ with perpetual licenses to connect Wall/Table mount touch 1 ₹ 123,500 ₹ 123,500

screen controllers and iOS and Windows devices as wireless touch controller.

Supply, Installation, Testing & Commissioning of High Definition, Multi-touch Touch Screen Controller with 24-

bit color display. Viewable Screen Dimensions (diagonal) – 7-inches or better, Resolution - 1280x800 or better,

Brightness - 380 Nits or better, Aspect ratio – 16:10 or better, Power – PoE, Mounting – Wall and Tabletop,

5.2 Wired Touch Controller 1 ₹ 357,500 ₹ 357,500

Orientation - Vertical / horizontal. Programmable LEDs on both sides to show various indications i.e.,

Mute/Unmute. Sensors - Ambient Light Sensor, Proximity Detection or better.

Supply, Installation, Testing & Commissioning of Room Scheduling Panel. Diagonal Size - 10-inches or larger,

Aspect Ratio-16:10 or better, Resolution -1920 x 1200 pixels or better, Status Indication LED's at side. Should

5.3 Room Scheduling Panel 1 ₹ 286,000 ₹ 286,000

support O365, MS Teams or more. Should have options to reserve the room from the Desk, Mobile App or on

the spot. Power- PoE.

Supply, Installation, Testing & Commissioning of 12 port L3 Gigabit POE+ Network Swicth, PoE Budget -

5.4 Network Switch 120Watts, with Multicast support with IGMP V1/V2, QoS support, IPV4/IPV6 Support, Switching Capacity in 1 ₹ 195,000 ₹ 195,000

Gigabits per Second, 1 Gbps Non-blocking ports with standard accessories.

CABLE, CONNECTORS, ACCESSORIES

6.1 Supply, Installation, Testing & Commissioning of 18Gbps 15-feet HDMI Cable. 1 ₹ 26,000 ₹ 26,000

6.2 Supply, Installation, Testing & Commissioning of 18Gbps 6-feet HDMI Cable. 1 ₹ 26,000 ₹ 26,000

6.3 Speaker Cable Supply, Installation, Testing & Commissioning of 2 core 2.5 sqmm PVC Sheathed loudspeaker cable. 1 ₹ 65,000 ₹ 65,000

6.4 Microphone Cable Supply, Installation, Testing & Commissioning of 2 core shielded balanced microphone cable. 1 ₹ 39,000 ₹ 39,000

Supply, Installation, Testing & Commissioning of 3-ft High speed USB C-C, USB 3.2 Gen 2 , 10Gbps cable with

DisplayPort™ Alt Mode Video and 65W Charging support.

6.6 CAT6 Cables Supply, Installation, Testing & Commissioning of Cat6 Cable for AV Network connectivity . 1 ₹ 39,000 ₹ 39,000

6.7 Equipment Rack Supply, Installation, Testing & Commissioning of 12U Rack with standrad accessories 1 ₹ 65,000 ₹ 65,000

Programming and

6.8 Programming & Commissioning charges for Audio, Video and Control 1 ₹ 156,000 ₹ 156,000

Commissioning Charges

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

BOQ FOR PLUMBING & FIRE FIGHTING

SECTION DESCRIPTION S.I (AMOUNT) N.S.I (AMOUNT)

A SANITARY FIXTURES & FITTINGS 7,514.65 583,798.67

B WATER SUPPLY 184,221.30 0.00

C INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES) 295,579.55 4,598.56

D SPRINKLER PIPING & ACCESSORIES 323,485.63 100,732.00

Total Cost ( Carried Forward) in Rs. 1,499,930.37

Digitally signed by RAJ PAL

BOQ FOR PLUMBING & FIRE FIGHTING

SUB HEAD A: SANITARY FIXTURES & FITTINGS

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Supply, installation, testing and commissioning of glazed vitreous china single trap syphonic pattern having back inlet,

supporting chair, wall hung water closet complete with all internal fittings/ accessories and CP brass flush bend

(European type) water closet with seat and lid, with C.P. brass hinges and rubber buffers, adapter, rubber joints fixed to

W.C., C.P. brass screwed washers including cutting and making good the walls and floors wherever required and HDPE

WC pan connector including jointing with white cement complete in all respects.

Wall hung W.C. pan (White colour)with white plastic seat & lid "Thermoset moulded ( bakelite ) IS 2548 Part I Each 4 20,000.00 80,000.00

2 MR Supply, installation, testing and commissioning of concealed cistern including flush plate and all internal fittings/

accessories including cutting and making good the walls and floors wherever required complete in all respects. Each 4 12,000.00 48,000.00

Supply, installation, testing and commissioning of glazed vitreous china wash basin with R.S. or C.I. brackets painted white,

32mm C.P. brass waste of standard pattern , C.P brass wall flange 32 mm dia. C.P. brass bottle trap and union 32 mm dia

C.P. pipes to wall flange. complete including cutting and making good the walls wherever required.

Table top wash basin Each 5 12,000.00 60,000.00

Supply, installation, testing and commissioning of 15mm C.P. brass single hole wash basin mixer without popup waste

4 MR system with 450mm long copper pipes and brass nut 6,064.37

5 MR Providing & fixing toilet paper holding including cutting and making good the walls. Each 4 1,561.92 6,247.67

Digitally signed by RAJ PAL

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing & fixing Horizontal liquid soap dispenser with stainless steel lid and brackets fixed to wooden cleats with C.P.

brass screws. Each 4 14,859.15

7 MR Providing & fixing C.P. brass coat hooks fixed on toilet door with C.P. brass screws Each 4 618.70 2,474.80

Providing & fixing beveled edge mirror 5.5mm thick of superior quality plate glass complete with 6mm thick marine ply

8 MR sheet ground fixed to wooden cleats with CP brass screws and washerswith 40 mm wide teak wood frame as per design

including polishing Sqm 8 2,814.69 22,517.49

9 MR Providing & fixing Hand Shower (Health Faucet) with 8mm dia, 1M long PVC tube and wall hook CP brass wall flange 1,781.81

Providing & fixing, testing and commissioning of storage type electric water heater with automatic thermostatic control

10 MR electric element, pressure release valve, brackets fixed to expansion fasteners with M.S. nuts and bolts all complete

including cutting and making good the walls wherever required.

a 05 litres capacity (Horizontal /Vertical type1.5 kw electrical load). Each 4 11,919.58 47,678.31

Providing & fixing wall mounted 25 mm dia Stainless steel coated grab bar including cutting & making good the walls(size

450mm long) Each 4 4,164.37

12 MR Providing & fixing 15 mm dia C.P. brass bib cock with C.P. wall flange of approved quality. Each 5 1,578.82 7,894.10

FRAGRANCE DISPENSER MACHINE :-Providing and fixing of Automatic Fragrance Dispenser machine complete with refill

can and 'C' size battery (2 Nos) for operation fixed to wooden cleats with CP brass screws Each 5

Providing and fixing of stainless steel finish Paper Towel Dispenser having capacity of 300-350 paper towels fixed to

wooden cleats with C.P. brass screws Each 5

Providing and fixing of wall mounted fully automatic hand dryer in SS/ black finish as per approval complete will all

accessories. Each 4

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40

16 17.10 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

17.10.1 Kitchen sink with drain board

17 MR Supply, installation, testing and commissioning of 15mm C.P. brass single hole sink mixer complete. Each 1 11,999.82 11,999.82

Providing, installing, testing and commissioning of package sump unit with built-in submersible drainage pump, nonreturn

valves, cutter, electrical panel/starter cabeling,common header, all as per standard design and including making

connections with grease separator/sink waste pipes drain pipe upto sewer shaft connections to be provided and make it

operational complete in all respect. Each 2 83,000.46 166,000.93

Detail of Sanitary fixture are for the information of the Contractor,however model/makes of all sanitary fixtures shall be

selected by Architect/Interior designer/Project manager and the same shall be binding for execution.

ii. No additional fixing cost shall be paid for change in type of sanitary fixtures.

iii. Contractor to receive all the above mentioned items & store at place as directed at site.

TOTAL CARRIED OVER TO SUMMARY 7,514.65 583,798.67

Digitally signed by RAJ PAL

SUB HEAD B: WATER SUPPLY

SL. DSR- DSR Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

(CPVC) plain & brass threaded fittings including fixing the pipe

with clamps at 1.00 m spacing. This including jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

18.7.5 40 mm nominal outer dia pipes. Metre 10.00 702.95 7,029.50

18.7.6 50 mm nominal outer dia pipes. Metre 10.00 934.15 9,341.50

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings i/c fixing the pipe with

2 18.8 clamps at 1.00 m spacing. This including jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting

chases and making good the the same including testing of joints

complete as per direction of engineer in charge.

Concealed work including cutting chases and making good the

18.8.2 20 mm nominal outer dia pipes. Metre 90.00 537.60 48,384.00

18.8.3 25 mm nominal dia Pipes Metre 90.00 627.25 56,452.50

18.8.4 32 mm nominal dia Pipes Metre 60.00 739.30 44,358.00

Providing and fixing brass stop cock of approved quality

18.16.1 15 mm nominal bore Each 4.00 353.25 1,413.00

18.16.2 20 mm nominal bore Each 4.00 379.20 1,516.80

Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end):

Digitally signed by RAJ PAL

SL. DSR- DSR Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty NS Rate (Rs.)

18.17.1 25 mm nominal bore Each 4.00 622.40 2,489.60

18.17.2 32 mm nominal bore Each 4.00 689.60 2,758.40

Providing and fixing C.P. bass angle valve for basin mixer and

5 18.53 geyser points of approved quality conforming to I.S:8931 a) 15

mm nominal bore.

18.53.1 15 mm nominal bore Each 6.00 574.30 3,445.80

Providing and fixing unplasticised P.V.C connection pipe with

PTMT Nuts coller and bush of approved quality and colour.

18.74.2 15mm nominal bore with 45cm length Each 24.00 121.90 2,925.60

Sub-Total of Water Supply Installation, Separate for Scheduled & Non-Scheduled Items 184,221.30

Digitally signed by RAJ PAL

SUB HEAD C: INTERNAL DRAINAGE (SOIL, WASTE & VENT PIPES)

SL. DSR-2023 DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing cast iron trap of self cleansing design with cast

iron screwed down or hinged grating with or without vent arm

complete, including cost of cutting and making good the walls and

100 mm inlet and 100 mm outlet centrifugally cast (spun) iron S&S as

2 17.35 Providing and fixing soil, waste and vent pipes.

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.1.2 100mm dia cast (spun) iron S&S pipe Metre 40.00 1,180.75 47,230.00

Centrifugally cast (spun) iron S&S pipe as per IS 3989.

17.35.2.2 75mm dia cast (spun) iron S&S pipe Metre 40.00 1,186.00 47,440.00

Providing and fixing single equal plain junction of reqd. degree with

3 17.43 access door, insertion rubber washer 3mm thick, bolts and nuts

17.43.1.2 Sand cast (spun) iron pipe IS-3989 Each 4.00 925.70 3,702.80

17.43.2.2 Sand cast (spun) iron pipe IS-3989 Each 4.00 665.05 2,660.20

4 17.44 Providing and fixing single equal plain junction of reqd. degree.

17.44.1.2 Sand cast (spun) iron pipe IS-3989 Each 4.00 811.90 3,247.60

17.44.2.2 Sand cast (spun) iron pipe IS-3989 Each 4.00 561.20 2,244.80

Digitally signed by RAJ PAL

SL. DSR-2023 DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

Providing and fixing bend of required degree with access door,

insertion rubber washer 3mm thick, bolts and nuts complete.

17.38.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 4.00 705.20 2,820.80

17.38.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 4.00 522.80 2,091.20

6 17.39 Providing and fixing bend of required degree .

17.39.1.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 30.00 570.05 17,101.50

17.39.2.2 Sand cast (spun) iron pipe S&S as per IS 3989. Each 4.00 390.50 1,562.00

7 17.57 Providing and fixing collar.

17.57.1.2 Sand cast (spun) iron pipe S&S IS-3989 Each 4.00 513.15 2,052.60

17.57.2.2 Sand cast (spun) iron pipe S&S IS-3989 Each 4.00 362.05 1,448.20

Providing and fixing MS holder bat clamps of approved design to

cast iron (spun) pipe embedded in and Including cement concrete

8 17.37 blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded

stone aggregate 20mm nominal size) including cost of cutting holes

and making good the walls etc.

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps.

including cutting and making good the walls etc.

18.10.4 32 mm nominal bore Metre 60.00 667.00 40,020.00

18.10.5 40 mm nominal bore Metre 60.00 811.90 48,714.00

Digitally signed by RAJ PAL

SL. DSR-2023 DSR Rate NS Rate DSR Amount NS Amount

DESCRIPTION OF ITEMS UNIT Qty

Painting G.I. Pipes and fittings with two coats of anticorrosive

bitumastic paint of approved quality

18.40.4 32 mm nominal bore Metre 60.00 22.20 1,332.00

18.40.5 40 mm nominal bore Metre 60.00 25.25 1,515.00

18.40.6 50 mm nominal bore Metre 35.00 30.50 1,067.50

Painting sand cast iron / centrifugally cast iron( spun) iron soil, waste

and vent pipes and fittings with paint of any colour such as

chocolate, grey or buff etc. over a coat of primer (of approval

quality) for new work

17.65.1 100mm dia cast (spun) iron S&S pipe Metre 40.00 82.80 3,312.00

17.65.2 75mm dia cast (spun) iron S&S pipe Metre 40.00 62.95 2,518.00

Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I.

13 NS Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen

complete in all respect.

100 mm diameter pipe (Hopper ) Each 4.00 1,149.64 4,598.56

Providing lead caulked joints to sand cast iron/centrifugally

cast(spun) iron pipes & fittings of diameter :.

Providing & filling the joints with spun yarn,cement slurry & cement

mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes.

16 17.48 Providing and fixing single unequal plain junction of reqd. degree.

17.48.1.2 Sand cast (spun) iron pipe IS-3989 Each 4.00 1,032.40 4,129.60

Sub-Total of Drainage Installation, Separate for Scheduled & Non-Scheduled Items 295,579.55 4,598.56

Digitally signed by RAJ PAL

D- SPRINKLER PIPING & ACCESSORIES

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Providing, laying, testing & commissioning of 'C' class heavy duty

MS pipe conforming to IS 3589/IS 1239 including Welding, fittings

like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing

the pipe on the wall/ceiling with suitable clamp/support frame

and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

Shifting of existing pipes including testing & commissioning of MS

pipe including Welding, fittings like elbows, tees, flanges, tapers,

nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with

suitable clamp/support frame and painting with two or more coats

of synthetic enamel paint of required shade complete as required

as per directions of engineer-in-charge.

Digitally signed by RAJ PAL

SL. NO. DESCRIPTION OF ITEMS UNIT Qty DSR Rate (Rs.) NS Rate (Rs.) DSR Amount (Rs) NS Amount (Rs)

Supplying, fixing, testing and commissioning of butterfly valve of

PN 1.6 rating with bronze/ gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS 13095 of

following sizes as required :

Providing and fixing ISI Marked of approved make Fire Extinguishers

complete with all accessories as per manufacturer's specifications.

4.1 CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 2.00 13,940.00 27,880.00

4.2 Mechanical Foam gas cartridge type. 9 Kg capacity (IS:15683). NOS 2.00 3,153.00 6,306.00

4.3 ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 6.00 2,796.00 16,776.00

Providing, fixing, testing & commissioning of 15mm dia quartzoid

5 18.21 bulb type sprinklers of rating 68 degree centigrade with required

5.1 18.21.4 Concealed Sprinkler Each 52.00 1,435.00 74,620.00

Supplying, installation, testing & commissioning of sprinkler flexible

pipe (UL Listed) of stainless steel complete with 15 NPT on reducer

thread with maximum working pressure of 175 PSI test pressure of

6 18.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to

sprinkler head (Outlet) 15mm NPT female thread with reducer,

nipple, 2 side brackets, center bracket, stockbar of following sizes

complete as required.

Providing and fixing signages printed on photoluminescent U1000

aluminium sheet of 1.0 mm (+ -10%) containing lumigen II as base

chemical, covered under UV stablized coating and of appropriate

size including fixing on wall, door, ceiling etc. with proper clamps,

hangers, cleats anchor fasteners etc. complete in all respects as

diercted by Engineer-in-charge

Providing, jointing and testing of automaticaly operated Halotron

8 NS fire extinguishers(cap-5kg,temperature rating - 68 degc,test NOS. 1.00 16,308.00 16,308.00

pressure-30bar) complete with all accessories/ fittings.

TOTAL CARRIED TO SUMMARY 304,228.00 100,732.00

Amount after GST Multiplication factor on DSR Items @1.0633 323,485.63 100,732.00

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar,

Summary of HVAC Works

S.No. Description of Works Amount (DSR, in Rs.)

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR -2022 NON- DSR

Sno. 2022 Ref Description Units Qty Rate Amount Rate Amount

1 MR Replace AHU canvas connections Nos 1.00 6,222.00 6,222.00

Supply, Installation, Testing Balancing & Commissioning of G.S.S

square/ rectangular ducting complete with gaskets, elbows, splitters,

vanes, supports adjustable dampers, etc. as per drawings and as

required for dehumidified air distribution of following thickness as per

approved working drawings and requirement .

iii 16.12.1.3 Thickness 1.00 mm sheet Sq.m 20.00 1,381.00 27,620.00

Supply and fixing of external thermal insulation on supply air ducts

with 19mm thick chemically cross linked closed cell polythene

(XLPE) fire retardant grade insulation of density not less than 30kg

per cum in single layer with factory lamination of 30 micron

aluminium foil or 19mm thick insulation as per CPWD specifications

Suply, installation, testing and commissioning of GI volume control

duct damper complete with neoprene rubber

gaskets,nut,bolts,screws linkages,flanges etc. as per specifications

Supplying, fixing, testing & commissioning of powder coated

5 16.15 extruded aluminium section supply air grills with aluminium volume Sq.m 4.00 9,105.00 36,420.00

control dampers, as per specifications.

Supplying, & fixing, of powder coated extruded aluminium section

6 16.16 return air grills with louvers but without volume control dampers, Sq.m 7.50 5,910.00 44,325.00

complete as per required.

Supplying, fixing, testing commissioning of supply air diffusers of

7 16.17 powder coated aluminium with aluminium volume control dampers. Sq.m 5.00 12,184.00 60,920.00

( 23Nos of 600x600mm)

Supplying, fixing, testing, commissioning of return air diffusers of

powder coated aluminium.

Supplying, fixing Acoustic lining of supply air ducting complete with

G.I frame, tissue paper, 28G perforated al. Sheet, 25mm thick

32kg/cu.m fibreglass insulation as per CPWD specifications.

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR -2022 NON- DSR

Sno. 2022 Ref Description Units Qty Rate Amount Rate Amount

Supplying, fixing , testing and commissioning of fire dampers in

supply air duct/ main branch and return air path as & where

required of required sizes including control wiring. The damper shall

be motorised and spring return so as to close the damper in the

event of power failure automatically and open the same in case of

10 power being restored .the spring return action shall be built

mechanism and not externally mounted . The damper shall also be

closed in the event of a fire signals complete as required as per

specifications .

b 16.20.2 Motorised Actuator No. 8.00 9,948.00 79,584.00

Supplying,fixing,testing and commissioning of Bypass type VAV

Boxes for climate control, made out of 20 gauge thick galvanised

steel sheet acoustically lined from inside; low leak multi blade

11 extruded aluminium motorized face & bypass volume control

damper with thumb-wheel adjustable thermostat. Dynamic factory

calibrated and adjustable flow of below mentioned capacity

complete in all respect.

Supplying, fixing, testing commissioning of Inline Fan of GI Casing

12 MR Circular / Rectangular Type with light weight dynamic balanced GI

Impeller, suitable forSingle Phase Motor (Without Speed Regulator,

Bird Screen and Louver) for toilet/ dinning / pantry exhaust.

Amount after GST Multiplication factor on DSR Items @1.0633 1,328,123.37 297,250.00

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

1.0 E&M 2025 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating

having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum

two compressors (with individual separate PCB) for above 14HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with R-410-A

Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as

required. To have better efficiency condenser fan shall be capable to operate at

different speed with respect to load. The unit shall deliver the rated capacity and in

confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C

ambient temperature without tripping. The system shall be able to deliver 100% of the

rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/-

7.3 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with

first charge of the refrigerant and ready for use as required. The condenser should be

coated with a hydrophilic film to prevent water accumulation on the surface of the heat

exchanger, enhance water dispersion, and reduce the risk of degradation, thereby

improving overall performance and durability. The Indian Seasonal Energy Efficiency

Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building

Code (ECSBC) 2024 as below and complete as per CPWD specification, connections,

inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and

<70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

2.0 INDOOR UNIT

Supply, Installation, Testing and Commissioning of following minimum capacity 4 way

Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan / dynamically balanced blower, multispeed motor,

coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump,

grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for

7.4 operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The

Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals.

The system shall be capable to adjust air flow as per room requirement in auto mode.

The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and

19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall

type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan

section with low noise fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control,

drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single

phase AC supply, complete as required. The Indoor units must shut down upon receiving

a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow

as per room requirement automatically. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be

same as of Outdoor)

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

1.0 E&M 2025 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen

testing of following nominal sizes of soft/hard drawn copper refrigerant piping for

VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular

insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of

19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

3.1 7.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 10.00 256.00 2,560.00

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 10.00 346.00 3,460.00

3.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 10.00 487.00 4,870.00

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 15.00 615.00 9,225.00

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

1.0 E&M 2025 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount NDSR Amount

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15.00 739.00 11,085.00

3.6 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 10.00 904.00 9,040.00

3.7 7.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 10.00 1,068.00 10,680.00

3.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 1,157.00 34,710.00

3.9 7.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,222.00 24,440.00

3.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,286.00 25,720.00

3.11 7.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 10.00 1,322.00 13,220.00

3.12 7.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 10.00 1,368.00 13,680.00

Supplying and installing of following size of perforated hot dip galvanized G.I cable tray

with perforations not more than 17.5%, in convenient sections, joined with connectors,

suspended from ceiling with G.I suspenders including bolts and nuts, etc. for carrying

refrigerant pipe in outdoor application as required.

4.1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 5.00 1,139.00 5,695.00

4.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 25.00 729.00 18,225.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with fittings,

supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and accessories as

per specifications, drawings.

6 MR Imported fittings Y-joints and headers etc. Nos 6.00 4,414.00 26,484.00

7 MR Timer for Split ac for Server Nos. 1.00 3,905.00 3,905.00

Digitally signed by RAJ PAL

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

PART A - E & M (EXCLUDING LIGHT FIXTURES & UPS SYSTEM)

SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 MAIN PANEL & DISTRIBUTION BOARD Rs. 308,016.00 Rs. 94,154.15

2 CABELS / MAINS Rs. 306,588.58 Rs. 25,869.03

4 PASSIVE NETWORK SYSTEM Rs. 215,870.00 Rs. 147,798.70

5 EPABX SYSTEM Rs. 908,803.19 Rs. 148,543.01

6 D.C. LIGHTING Rs. 3,437,004.00 Rs. -

7 CABLE TRAY.& RACE WAY. Rs. 201,226.00 Rs. 78,152.55

8 ACCESS CONTROL SYSTEM Rs. 1,941,460.62 Rs. 16,342.92

9 FIRE ALARM & PA SYSTEM Rs. - Rs. 729,793.83

GRAND TOTAL Rs. 10,038,887.67

GRAND TOTAL Rs. 10,038,887.67

PART B - E & M (LIGHT FIXTURES & UPS SYSTEM)

SUB HEAD NDSR AMOUNT (Rs.) DSR AMOUNT (Rs.)

1 LIGHTING FIXTURES Rs. 2,663,704.50 Rs. 147,460.00

2 UPS SYSTEM Rs. - Rs. 442,020.00

GRAND TOTAL Rs. 3,253,184.50

GRAND TOTAL Rs. 3,253,184.50

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

1 MAIN PANEL & DISTRIBUTION BOARD

1.1 Supply,installation,testing and commissing of 3 phase and neutral 415V 4 wire free standing floor mounted

indoor MV panel made out of 14 SWG sheet after seven tank process and painting with epoxy powder

coating MV electrical panel shall be dust and vermin proof ,hinged and locable doors.The panel shall

consist of suitable rating TPN bus bar at the rating of 0.8A /SQMM Supported by DMC/SMC insulator and

color coded with heat shrinkable sleeves. Metering shall be provided as specified .The panel shall have

short circuiting with standing capacity of minimum 36KA and consist of the switch gear as mentioned

below .The panel shall got fabricated from manufacturer with CPRI test certificate .The panel shall be

mounted on U channel including supply and fixing of the same.(including Capacitor banks)

250 Amps 4P 36KA MCCB. -1No.

Spreaders-1Set.

Extended Rotary Operating Mechanism.-1Set

Digital V A F Meter with built in Selector Switch, CTs, CT shorting links, R/Y/B LED indicating lamps and

control SP MCBs.

Outgoing Section

63 Amps FP MCB_C curve -5Nos.

100Amps 4P25KA MCCB-1Nos.

40 Amps FP MCB_C curve -3Nos.

32 Amps DP MCB -2No.

8 Step Automatic Power Factor Correction Relay (Digital)_1 No

10 kVAR AC3 Duty Contactor with 220 V AC Coil_3 Nos

5 kVAR AC3 Duty Contactor with 220 V AC Coil_4 Nos

ON / OFF LED Indicating Lamps _7Set

Start / Stop Push Buttons_7Set

A/M Selector Switch_1 No

Control S/P MCB (2/4 A)_7 Nos

Neutral Links_7 Nos

Control Blocks_7 Nos

Enclosure, 300A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100% neutal& Non adhesive

PVC insulated heat shrinkable sleeves, Internal Wiring, Terminals, etc.as required.

1.2 Supplying the following MCCBs in sheet steel enclosure. For Ups Input & Output

100A 4P MCCB in sheet steel enclosure surface mounted on the wall along with incoming & outgoing

Cable Box, suitable for Termination of Aluminium / Copper Cable. (For Ups Input )

b) UPS Output panel

100 A 4P Onload changeover switch in sheet steel enclosure surface mounted on the wall along with

incoming & outgoing Cable Box, suitable for Termination of Aluminium / Copper Cable.

- Outgoing Section

- 80 Amps FP MCCB -3No.

- Spreaders-3Set.

- Extended Rotary Operating Mechanism.-3Set

Enclosure, 100A TPN 415V 50Hz Electrolytic grade AL conductor Busbar with 100% neutal& Non adhesive

PVC insulated heat shrinkable sleeves, Internal Wiring, Terminals, etc.as required._1Set

1.3 DISTRIBUTION BOARDS.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on

2.3 surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)+

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution

2.4 board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution

board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar,

common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required .

(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for

2.10 inductive load of following poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit

2.14 breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit

2.15 breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections,

testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, MCB in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Total of Main Panel/ DB carried over to summary 308,016.00 88,549.00

Amount after GST Multiplication factor on DSR Items @1.0633 308,016.00 94,154.15

2 CABELS / MAINS

Supply ,laying,testing and commissoning of 1100V grade armoured cable having sector / circular shaped

aluminium / copper conductor PVC insulated cores under ground PVC tape wrapped inner sheathed, GI

2.1 strip / wire armoured and overall extruded PVC sheathed confirming to IS: 1554, laid on wall or ceiling

using GI clamps and spacers as per route shown at site and further as directed by Engineer-in charge

a MR 250 Sq.mm 3 1/2 core Aluminium cable mtr. 30.00 0.00 0.00

b MR 25 Sq.mm 4 core copper cable mtr. 60.00 0.00 0.00

c MR 16 Sq.mm 4 core copper cable mtr. 120.00 0.00 0.00

d MR 10 Sq.mm 4 core copper cable mtr. 50.00 0.00 0.00

e MR 6 Sq.mm 3 core copper cable mtr. 50.00 612.00 30,600.00

f MR 4 Sq.mm 3 core Copper cable mtr. 120.00 2,299.90 275,988.58

Supply & fixing of end termination for above mentioned cables including compressed type brass glands,

2.2 crimping type coper lugs, insulation tape etc. as 'required complete with earthing of glands in following

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Total of Cables / Mains carried over to summary 306,588.58 24,329.00

Amount after GST Multiplication factor on DSR Items @1.0633 306,588.58 25,869.03

Point wiring for light point /Fan/Exhaust Fan point/ call bell point using 2 runs of 1100 V grade 1.5 sqmm &

one run of 1.5 sq.mm FRLS insulated multistranded copper wires, in & including 25 mm dia , MS conduit

3.1 surface/ concealed in wall / ceiling conferming to IS 732 including all accessries such as junction boxes ,

conduit bends, elbows and ceiling rose , and anodised GI switch box with modular switch ,modular plate

and the box covered with front plate

a 1.3.3 One light point controlled by one 6A switch Per Pts 20.00 1,845.00 36,900.00

b 1.54.3 Secondary light point controlled by same switch Per Pts 20.00 1,094.00 21,880.00

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed steel conduit as required.

a 1.7.1 2x1.5sqmm+1x1.5sqmmearth wire Per mtr. 550.00 327.00 179,850.00

c 1.7.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Per mtr. 600.00 428.00 256,800.00

3.3 1.3.3 Exhaust fan point including of ceiling rose near fan. Per Pts 3.00 1,845.00 5,535.00

Wiring for twin control point wiring using 1.5 sqmm copper conductor FRLS PVC insulated copper

conductor cable drawn through 25 dia MS conduit laid in surface/concealed over false ceiling or in

slab/wall chases including ,2way modular switches,modular plate ,suitable GI box and earthing the point

with 1.5 sqm FRLS PVC insulated copper conductor single core cable as required

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including

connections but excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 20.00 122.00 2,440.00

d 1.24.5 6 pin 15/16 A socket outlet Each 40.00 197.00 7,880.00

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular

switches in recess etc. as required.

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated,

3.9 1.19 shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed Meter 51.00 47.00 2,397.00

steel/ PVC conduit as required.

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

3.10 MR Supplying and laying HDMI Cable with connector on both ends. Meter 50.00 81.00 4,050.00

Supply and fixing of following sizes of MS conduit along with accessories in surface /recess including

3.11 1.20 painting in case of surface conduit,or cutting the wall and making good the same in case of recessed

conduit as required

Supply and fixing of 3 nos. 6A socket with 6M modular GI box, base plate and cover plate below worktop,

along with 1no. 6A socket, 1 no. 6A switch and 1 no. 16A switch(for 3 nos. sockets) in 4M modular GI box,

base plate and cover plate above worktop complete as per drawings and instructions of engineer in

Total of Wiring carried over to summary 40,690.00 981,399.00

Amount after GST Multiplication factor on DSR Items @1.0633 40,690.00 1,043,521.56

4 LIGHTING FIXTURES

4.1 1.3 LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round

/square/Rectangular) SMD type of following body material with PMMA and prismatic diffuser and

construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal

surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

(Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical

circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends as per

LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) ,

SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its

own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections

with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from

NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be

as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum

housing such that LED junction temperature shall not rise above 90°C).

4.2 1.9 LED Batten light (System lumen efficacy ≥105 <120 lm/Watt)

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body

material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver

efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40

deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.

F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitary),

of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K /

5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and

trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on

housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy

≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as

per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature

shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body (Thickness

Supply, installation, testing and commissioning of 13W LED (1.2m) linear recessed mounted LED Fixtures

constructed with extruded aluminium housing and high efficiency plastic diffuser, suitable for ambient

temperature from 0 to 45 deg C. It shall deliver a higher system efficacy greater than 120 lumen/watt, IP20

protection rating, color temperature options of 4000K and 5700K, minimum CRI of 80, and rated life

4.3 MR exceeding 50,000 hrs. (L70 Criteria), as per ANSI Bin C78.377A ensuring uniform and efficient illumination. Nos. 20.00 17,030.00 340,600.00

Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India.The fixture

shall be compatible for Power over Ethernet (PoE) operation through Cat-6 cabling, supporting smart and

low voltage lighting networks without the requirement of traditional drivers. The luminaire shall comply to

detailed specs as stated under "PoE based Lighting"

Supply, installation, testing and commissioning of luminaire shall be a linear/ curvi-linear suspended

mounted LED Fixtures constructed with extruded aluminium housing and special translucent flexible silicon

diffuser, suitable for ambient temperature from 0 to 45 deg C . It shall deliver a higher system efficacy

greater than 90 lumen/Watt, IP20 protection rating, color temperature options of 3000K/4000K /5700K,

4.4 MR minimum CRI of 80, and rated life exceeding 50,000 hrs (L70 Criteria), as per ANSI Bin C78.377A ensuring RMT 85.00 21,500.00 1,827,500.00

uniform and efficient illumination. Manufacturer shall have inhouse lab approved by NABL or ministry of

science of govt of India.The fixture shall be compatible for Power over Ethernet (PoE) operation through

Cat-6 cabling, supporting smart and low voltage lighting networks without the requirement of traditional

Providing & Fixing Coverings (Ceiling & Wall) Made out of Polyester Kintted fabric Coated with

polyurethane (PU). The Fibric width 2m,3m,4.1m,&5.1m with Weight of 200gm/m^2. thickness of 0.3mm. The

appearance of fabric is Matl. smooth and uniform with blance color and ligth transmission of 50%. The tear

strength of fabric should be accordance to CH. 4.5daN; TR: 6.5 daN. The fire Railing should be accordance

to B-S1, do. The febric should be humidity ressistant and free of cercinogenic subtance (CMR) or volatile

organic compounds (VOC's). At lableing in accordance with the French decree no, 2011- 321, Oeko -Tex

standar100 certified. The fabric should be paintabe/printable with approved manufacturer guidelines with

4.5 MR 10-year manufacture guarantee. the Installation of fabric should be dry installation 7done at room Sqm 5.00 12,315.00 61,575.00

tamperature using CLIPSO PVC, ASB tension profiles P.CC/P-C10QS/P-C11QS/P-CCB022/P-B1/P-CC1P.

There are several lighting options available including various LED options and fluorescent lighting. When

Positioned properly. LED Lighting modules provide an even light flow, casting no shadowns or hot spots.

coverings are used for a variety of aluminated applications, including but not limited to walls, ceiling,

lightboxs or wall frames. coverings can enhance your door with a variety of spacial effects fiber optics or

changinglights, or create a statement piece incorporating custom printing. The cost of electrical cove light

fixtures is included in the same.

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Supply, installation, testing and commissioning of luminaire shall be a aesthetically slim designed profile

suspended mounted LED Fixtures constructed with extruded aluminium housing and special high Efficiency

Translucence (HET) diffuser for uniform light Distribution without glare, suitable for ambient temperature

from 0 to 45 deg C. Luminaire shall design with Technology edge with high efficacy LEDs for optimal light

output. It shall deliver a higher system efficacy greater than 90 lumen/watt, IP20 protection rating, color

temperature options of 4000K /5700K, minimum CRI of 80, and rated life exceeding 50,000 hrs (L70 Criteria),

as per ANSI Bin C78.377A ensuring uniform and efficient illumination. Manufacturer shall have inhouse lab

approved by NABL or ministry of science of govt of India.The fixture shall be compatible for Power over

Ethernet (PoE) operation through Cat-6 cabling, supporting smart and low voltage lighting networks

without the requirement of traditional drivers.

4.7 MR SITC of decorative light fixture as per selection of the client (BR = Rs. 5000) Nos. 3.00 7,463.50 22,390.50

4.8 MR SITC of decorative light fixture as per selection of the client (BR = Rs. 20000) Nos. 1.00 29,854.00 29,854.00

Providing & Fixing Heavy Duty 4 Blade, 15" Exhuast Fan complete with all hardware and connectors etc., as

per the direction of the engineer In charge

4.10 1.5 LED Down lighter (COB Type) (System lumen efficacy ≥120 lm/Watt )

Supplying, installation, Testing & Commissioning of LED Recessed / surface Down lighter (Round / square/

Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating

temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should

be below 5 %), life time (LED,Driver & electrical circuitry), life time of minimum 50000 Burning Hours with ,

70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin),

SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its

own in house NABL lab setup for all testing facilities for LED fixtures. "complete in all respect i/c connections

with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report

from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall

be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum

housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded

aluminium Body including trim with Aluminium Reflector

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Total of Light Fixture carried over to summary 2,663,704.50 147,460.00

5 PASSIVE NETWORK SYSTEM

Supply, Installation, Testing & Commissioning of LED 24 Port loaded Cat 6 Jack Panel, Staggered 24

Port panel with All port LED in 1U Rack Unit, Copper Alloyed Contact Material, EIA 568A/B wired, PC +

glass fiber, UL 94V-0, black color, Front Port Labeling, 22-24 AWG Wire Accumulation etc.

complete as required.

Supply, Installation, Testing & Commissioning of dual face plate having provision for one I/O

along with spring type shutter for dust proof, made of ABS PVC plastic etc. complete as required.

Supply, Installation, Testing & Commissioning of single face plate having provision for one I/O along

with spring type shutter for dust proof, made of ABS PVC plastic etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Information Outlet, Universal label permits

5.4 T568A or B wiring, UL® Listed, meets all TIA and ISO requirements Complete in all respect as required by the Each 20.00 362.00 7,240.00

site etc. complete as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC

conduit as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 1 Mtr, 4 pair 26 AWG

stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for

EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements. Complete in all respect as

required by site completion etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 2 Mtr, 4 pair 26 AWG

stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for

EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements. Complete in all respect as

required by site completion etc. complete as required.

Supply, Installation, Testing & Commissioning of 6 Core Armoured single Mode Fiber optic

5.8 cable, Central Lose Tube With Jelly Compound, Corrugated steel tape armoured, Heaving 1300 nm Mtrs. 100.00 270.00 27,000.00

Wavelength in the existing surface/ recessed Steel/ PVC conduit etc. complete as required.

Supply, Installation, Testing and Commissioning of single Mode fiber SC-LC Duplex patch cord of 2

Mtrs. for Gigabit Connection between Patch Panel and Switch etc. complete as required.

Supply, Installation, Testing & Commissioning of 24 Port fully loaded Line Interface Unit LIU, 19",1u Rack

5.10 Mountable unit with splice Tray Holder, Cable Guide, Fiber Management and Splicing of Pigtails Each 1.00 27,800.00 27,800.00

and Fiber Cables Including Joints and Connectors etc. complete as required.

Supply, Installation, Testing & Commissioning of Horizontal cable manager etc. complete as

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

5.12 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit as

Total of Passive Network System carried over to summary 215,870.00 139,000.00

Amount after GST Multiplication factor on DSR Items @1.0633 215,870.00 147,798.70

6 D.C. LIGHTING

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

SITC of Smart Lighting Controller offering multiple channels for remote constant current/voltage LED

driving. This controller to have 8 ports ( RJ45 ) that can deliver controlled power in either IEEE standard

(90W per port) with an optional network card or extended -PoE (110W per port) configurations. Powered

by a 48V-57V low-voltage DC input, it must ensure efficient and reliable operation within the lighting

system, maintaining consistent and optimized power supply to the connected LED fixtures. The controller

provides power supply & dimming of 16 channels of LED Lighting groups, with each group drawing

maximum current of 1.2 Amp and maximum voltage of 48V. Each of Lighting Channel should be capable

of powering & dimming from 0 to 100% with 1% increment ( constant voltage and Constant current loads-

both need to be possible). The controller needs to provide API level control with GUI ( Graphic User

Interface), Operating Temperature of 0 to 50° . The controller need to be UL & CSA certified. The controller

would have two nos UP/DOWN Link RJ45 Ports; 8 nos IEEE 802.3bt PoE++ ( with optional network card) / 2-

CH extended-PoE Lighting RJ45 Ports(1) DC Power Input Port(1) Aux. Dry Contact Input Port(2) Pin-Hole

Operation/Reset Buttons. Certification: UL,FCL,ETL. Communication protocol:MQTT ,Operating Temp: 0°C

Storage Temp: -20 to +40°C (-4 to +158°F)

Humidity: 10% to 90% (non-conde)

SITC of AC-DC SMPS upto 1000w, adjustable from 48V to 55V & 21A, min. 1500ms rise time, min. 95% eff.,

6.2 <2mA leakage current, constant current limiting with hiccup mode, shutdown on over voltage, auto fan Nos 12.00 9,440.00 113,280.00

control, Compliance to EACTPTC 020,KC KSC 9832, KSC 9835,

SITC of Powered device with 2 RJ45 inputs & 2 - 2 core DC circuits, 48-57V input; to split input current from

Smart Controller ports to 2 individually dimmable Lighting groups.

SITC of Controls Switch equipped with screw/push type connectors or Ethernet cable connectivity for

efficient lighting management. It can be configured using lighting management software. Additionally,

6.4 the switch will offer the option to program a single button with three actions: Push, Push and Hold, and Nos 11.00 6,490.00 71,390.00

Double Tap, allowing for three separate action sets. Communication of switch actions would be on secure

wireless mesh ( 6LoPWAN technology) or on CanBUS

SITC of Smart Networked Sensor shall P.I.R. technology for high-precision presence detection, capable of

acquiring data related to occupancy and lux levels. The communication of sensor data will be on a

secure wireless mesh network ( 6LoPWAN technology) . It will operate within a voltage range of 24V DC,

with a power consumption of less than 2W. The sensor’s IP rating will be IP67, and its housing will be made

from UV-resistant polycarbonate, designed to function in temperatures from 0°C to 40°C. It will feature fine

adjustment for light measurement output, ranging from 100 to 1000 lux. The product will be compatible

with an LMS-based lighting control system, ensuring an energy-efficient, IoT-ready lighting solution.

Additionally, the sensor will provide temperature and humidity data to the IP network.

SITC of 24V-10A SMPS shall be designed to support sensors, providing a stable 24V DC output with a current

capacity of up to 10A. It will be energy-efficient, ensuring reliable operation of connected sensors while

maintaining low power consumption. The power supply will feature overcurrent, overvoltage, and short-

circuit protection to ensure safe and continuous operation. It will be housed in a durable enclosure,

suitable for installation in various environments, and will comply with relevant safety and performance

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

SITC of a gateway with hardware and software components, including a scalable processor for real-time

data processing and API interactions. The gateway will feature Ethernet ports, along with wireless modules

(6LoPWAN) for communication with switches and sensors. It will support sufficient RAM, non-volatile storage

for firmware and logs, and low-power operation compatible with existing infrastructure. The system will

have expansion ports for future integration, and the OS will be a lightweight real-time version (e.g., Linux or

RTOS). The gateway will support RESTful APIs, MQTT, WebSocket protocols, and provide a web-based GUI

and mobile app for configuration. Security features will include encryption (HTTPS, TLS), role-based access

control (RBAC), and secure firmware updates (OTA). The gateway will monitor and control ports, support

wireless integration, automation via schedules/triggers, and log device activity, power usage, and alerts

with export options. Additionally, it will offer dry contact functionality for passive switching of features like

dimming and emergency lighting, with compatibility for both voltage-free and current-controlled inputs.

Hardware will include RJ45 connectors, a wireless module, and power management within system delivery

limits. The enclosure will be durable, weatherproof, and compact. The system will comply with relevant

standards (e.g., IEEE, CE, UL, FCC).

SITC of Touch Pad -oF APPLE MAKE Ipad Apple iPad (10th Generation): with A14 Bionic chip, 27.69 cm

(10.9″) Liquid Retina Display, 64GB, Wi-Fi 6, 12MP front/12MP Back Camera, Touch ID, All-Day Battery Life

SITC of wiring for light point with with UTP 4 Pair CAT 6 Cable in surface PVC conduits in false-

6.9 ceiling/walls/ceiling, (Average length between the DC IOT hUB to First Point Primary (Including 25mm PVC Nos 96.00 1,180.00 113,280.00

Conduit, and Accessories, RJ 45 connectors)

SITC of wiring for group controlled (looped)light point with with 2 Core DC Cable in surface / recessed

6.10 medium class PVC conduit etc.in F.ceiling/walls/ceiling as required. Class 2 Wiring ( 2 core DC cable), Nos 458.00 1,003.00 459,374.00

(Including 25mm PVC Conduit, and Accessories, DC-DC connectors)

SITC of controller with number of inputs and outputs, including an HDMI output to enable an on-screen

display (OCD) interface. The processor to be able to the integration of third-party devices for the smart

home or smart business, such as audio and video distribution, lighting, shades, security, and HVAC.

Control to be delivered via IP, RS-232, infrared, relays, and sensing to support the entire ecosystem and

connected subsystems, allowing for easy expansion using multiple processors and a complete line of

6.12 accessory devices. This program to work quickly with Integration Designer programming software. Nos 1.00 252,402.00 252,402.00

The controller should be suppled along with Power supply (12V, 1A), RJ45 to DB9 serial adaptor and

necessary accessories. • Should Supports RM433 (433MHz) and ZM24 (2.4GHz Zigbee) RF modules.

Minimum Technical Specification: • Ethernet port • Six MPIO / IR ports, • Three RS232 ports • Three relays •

Three 12VDC voltage triggers • Three voltage sense inputs • Master or slave processor (to make expansion

device) • Astronomical time clock • Rack mountable 1RU hardware included

SITC of 640ma Power Supply with 30 VDC KNX Bus Power. 30 VDC Aux Power. Reset Button for Issue

Recovery. Power and Overload Indicators, input voltage: 230 Vac, 50/60 Hz

Power absorption 22 W, Loss < 3 W

6.13 Output voltage (KNX bus): 30 Vdc Nos 1.00 50,150.00 50,150.00

Output voltage (auxiliary output): 30 Vdc

Nominal current (output total): 640 mA

Buffer time: 200 ms

SITC of KNXnet/IP Interface with.. Single Tunnel. Supports KNX Data Secure Protocol Shows the user-defined

name and if the connection type is IP, the assigned IP address (as well as MAC address; the address will be

accepted when the connection is established/configured).

The user-defined name on KNXnet/IP tunneling (devices) is downloaded into the device later on. The

maximum length of the name is 30 characters.

When the device is discovered by ETS, then this name is shown.

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

SITC of Kitchen Dispaly Screen Size 32 Inches

Display TechnologyLED

Refresh Rate60 Hz

Special FeatureOfficial Android TV 11(R) | Built-in Assistant | RAM: 1GB | ROM 8 GB | Quad Core

Processor | Built-in Assistant | RAM: 1GB | ROM 8 GB | Quad Core Processor |

Included Components‎1 TV Unit, 1 Remote, 2 Table Top Stand, 2 AAA Battery, 1 User Manual

Connectivity TechnologyWi-Fi, USB, Ethernet, HDMI

Aspect Ratio16:9

Product Dimensions8.3D x 72.6W x 46H Centimeters

Total of DC lighting System carried over to summary 3,437,004.00 0.00

7 EPABX SYSTEM

Supply, Installation, Testing and commissioning of Executive Level IP Phone with Color display – 3.7 inches x

2.1 inches (9.5 cm x 5.4 cm)- Diagonal width: 4.3 inches (11 cm), Touch Screen display, 4-position

adjustable tilt display, Permanently-labeled feature buttons:, speaker, mute, headset, contacts, home,

history, message, phone, forwarding, volume (separate volume levels in handset, speaker, ringer, and

headset), Red LEDs on speaker, mute, headset, message and history, 24 administrative buttons, Wideband

speakerphone 0-5 Softkeys, Ergonomic hearing aid compatible, handset supporting TTD acoustic coupler,

Bluetooth and DECT headset support with adapter, Message waiting indicator, Ethernet (10/100/1000)

line interface, Secondary Ethernet (10/100/1000)line interface, Optional IEEE PoE 802.3af adapter registers

as class 2 device, SIP protocol, H.323 protocol support, Standards-based codec support: G.711, G.726,

G.729A/B, G722 , Include License.

2.8” (diagonal) color display—320 x 240 pixels, Multiple line phone with four red / green line / feature

indicators around display, 4 Context sensitive soft keys, Hard buttons for phone, messages, contacts,

history, home, navigation cluster, headset, speaker, volume, mute, LEDs for speaker, mute, headset,

message, history, Wideband audio in handset and wired headset, Full duplex speakerphone & handset,

Ergonomic hearing aid compatible handset supports TTD acoustic coupler, Message waiting indicator,

7.2 Mute key with optional mute alerting, IC call alerting with 360-degree visibility, Dual-position stand, optional Each 3.00 19,871.00 59,613.00

wall-mount stand, Gigabit Ethernet (10 / 100 / 1000) line interface, Second Ethernet interface 10 / 100 /

1000 Mbps, PoE Class (IEEE 802.3af) registers as class 1 device and supports 802.3az, Optional AC to 5 volt

power supply • SIP protocol support, Standards-based codec support: G.722, Opus, Configurable via Web

interface, Support for HTTPS, TLS and SRTP for encryption, Recent Call Log (100 entries), Zero touch

deployment via Device Enrollment Services Support, Include License.

7.3 Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight. Each 10.00 1,957.00 19,570.00

Supply, Installation, Testing & Commissioning of LED 24 Port loaded Cat 6 Jack Panel, Staggered 24

Port panel with All port LED in 1U Rack Unit, Copper Alloyed Contact Material, EIA 568A/B wired, PC +

glass fiber, UL 94V-0, black color, Front Port Labeling, 22-24 AWG Wire Accumulation etc.

complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 1 Mtr, 4 pair 26 AWG

7.5 stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for Each 20.00 408.00 8,160.00

EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 2 Mtr, 4 pair 26 AWG

7.6 stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on boots, Suitable for Each 20.00 560.00 11,200.00

EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Infornmation Outlet,Universal label permits

T568A or B wiring, UL® Listed, meets all TIA and ISO requirements etc. complete as required.

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC

conduit as required.

Supply, Installation, Testing & Commissioning of 6 Core Armoured single Mode Fiber optic

7.9 cable, Central Lose Tube With Jelly Compound, Corrugated steel tape armoured, Heaving 1300 nm Mtrs. 100.00 270.00 27,000.00

Wavelength in the existing surface/ recessed Steel/ PVC conduit etc. complete as required.

Supply, Installation, Testing and Commissioning of single Mode fiber SC-LC Duplex patch cord of 2

Mtrs. for Gigabit Connection between Patch Panel and Switch etc. complete as required.

Supply, Installation, Testing & Commissioning of 24 Port fully loaded Line Interface Unit LIU, 19",1u Rack

7.11 Mountable unit with splice Tray Holder, Cable Guide, Fiber Management and Splicing of Pigtails Each 1.00 43,140.00 43,140.00

and Fiber Cables Including Joints and Connectors+B592 etc. complete as required.

Preparation of complete set of MEP drawings including details. A qualified professsional for the purpose

shall be appointed after due appproval from Engineer In Charge.

Supply, Installation, Testing & Commissioning of Horizontal cable manager etc. complete as

Supplying and fixing of following sizes of medium class PVC conduit along with accessories

7.14 1.21 in surface/recess including cutting the wall and making good the same in case of recessed

conduit as required.

7.15 42U network rack including PDU and other accessories complete Each 1.00 76,500.00 76,500.00

Total of EPABX SYSTEM carried over to summary 908,803.19 139,700.00

Amount after GST Multiplication factor on DSR Items @1.0633 908,803.19 148,543.01

8 CABLE TRAY.& RACE WAY.

Supply, fabrication and fixing of steel frame work in position for cable tray/Panels fabricated out of 10 mm

dia GI rods, ISA-40 MS angle iron, ISMC-50 channels, flats etc.complete with providing of Anchor fastners

8.1 and all necessary hardwares as required for fixing, including cutting, bending, welding, drilling, bolting etc.

as per design as required and painted with one coat of primer and two coats of enamel paint of

approved shade.

Supply and fixing of Perforated type 2mm thick Hot dip Galvanised G.I. cable tray of following sizes

complete with bend/tee joints, coupling plate & nuts bolts etc. as required for fixing and including the cost

of providing loop earthing with 2 nos. 50 mm x 6 mm GI earth strips complete as per specifications, as

required and as below.

8.2 GI Raceway & Junction boxes ( Raceway on floor shall be of aluminium only)

Providing and fixing 2 mm thick steel sheet factory fabricated post galvanized raceway with internal

partition/compartmentized of the following sizes including providing removable 3 mm thick GI cover,

knock out holes and fixing accessories earthing with 8 SWG copper earth wire complete as required

including floor supports, bends, access boxes, tap off boxes and cross over as per specification and site

requirement. (overhead / wall mounted recovery & function boxes shall be 1.6 mm thick)

a) 300 mm wide x 38 mm deep raceway RM 20.00 2,476.00 49,520.00

b) 225 mm wide x 38 mm deep raceway RM 20.00 2,074.00 41,480.00

c) 150 mm wide x 38 mm deep raceway RM 30.00 1,490.00 44,700.00

d) 100 mm wide x 38 mm deep raceway RM 30.00 1,109.00 33,270.00

Providing and fixing 350 x 350 x 60 mm deep 2 mm thick GI sheet junction box including providing 3 mm

thick stainless steel cover as per specification.

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet junction box including providing 3 mm

thick stainless steel cover as per specification.

Total of Raceway carried over to summary 201,226.00 73,500.00

Amount after GST Multiplication factor on DSR Items @1.0633 201,226.00 78,152.55

9.1 Online UPS - Input supply: Single Phase, Output Supply : Single Phase

Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) ON

LINE Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC

Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH

capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery

shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass,

suitable isolation transformer for additional protection against neutral faults etc. The UPS systems shall be

Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier &

inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and

inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The

operating efficiency of the UPS systems shall be >95% at 100% non-linear loads. Current total harmonic

distortion (ITHD)/ total demand distortion (TDD) on the input grid shall be < 5% at 100 %load. (The required

LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0.99

and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ) however UPS shall

be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming

supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine wave single phase

220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins and 150% for 1 minute.

condensing, noise level less than 60db at 1 meter distance, Protection for Under voltage, over voltage,

abnormal output voltage, battery over charging, output over current, short circuit, battery deep discharge

, 10 KV surge. Display for watt/VA,Amp and Voltage power parameters etc. UPS shall comply with low

voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be

a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 & 3) . The UPS should

be with IGBT Based Inverter Technology, Communication RS232/RS485/SNMP port open protocol for BMS

integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable

rating and interconnecting copper conductor cable of suitable size and connectors and all required

accoseries are inclusive in the cost. The UPS should have QR code which should contain drawing, test

report OEM manual, Geo- Tag of manufacturing location etc

9.2 5.2 Online UPS- Input supply: Three Phase, Output supply: Three Phase

Digitally signed by RAJ PAL

VASTU MANDAL archit ect s, int er ior designers

F-328, Old MB Road . Lado S ar ai. Mehr aul i, New Delhi 110030

Te lfax 41665455 Emai l :vast umandal @gmail .com

Interior Fit-Out Works in The Office Space of the Munitions India Limited at World Trade Centre, Nauroji Nagar, New Delhi

DSR-2022 Description

S.No Unit Qty Rate MR Amount DSR Amount

Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor) at

operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine wave

Uninterrupted hot swappable (allow for the replacement or addition of battery modules without shutting

down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of

moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30

minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour

backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith

provision for manual bypass, suitable isolation transformer for additional protection against neutral faults

etc. UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest

technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar

Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of

design, manufacturing and inspection process should confirm to the relevant International standards such

as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode

and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input

grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included

in UPS cost), extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output

power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS shall be suitable

to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC :

3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity

of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter distance,

protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over

current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low

voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be

a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port open

protocol for BMS integration, all hardware & software for iOT Communication as per approved by

Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable

size and connectors and all required accoseries are inclusive of the cost).

This system must provide a means for logging and alarming of all monitored points plus email notification.

Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle

at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC

62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC

Display / LED ) to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output:

Voltage, frequency, Current. d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage. f)Temperature:

STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to

3000 events like: Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail

/ Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass /

Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load

/ UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible

Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown, Input Over, Under Voltage,

Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over Temperature.

The UPS should have QR code which should contain drawing, test report OEM manual,Geo- Tag of

manufacturing location etc.

5.2.2 20KVA (Each Power module shall be < 10 KVA) Each 1.00 341,772.00 341,772.00

Total of UPS system carried over to summary 0.00 442,020.00

Digitally signed by RAJ PAL

DSR NDSR Total

Sr. No Description Unit Qty Unit Rate DSR Total amount

Sr. No Description Unit Qty Unit Rate DSR Total amount

ref. no. amount

7 IP BASED CCTV SYSTEM

Supply, installation, testing and commissioning of IR & IP Based dome type indoor

coloured fixed camera with of 1/3" CCD,540 TVL, Sensitivity @ 30 IRE: Color

7.1 0.5Lx/Night Sense 0.18 Lx, AWB / BLC / AGC /Auto Black, 2.6 to 6 mm vari-focal lens Nos. 10 Rs. 7,200 Rs. 72,000

Auto Iris, 12VDC/24VAC for indoor application, complete in all respects as per

specifications as per engineer in charge.

Supply, installation, testing and commissioning of DVR-20-CH, 400/480fps display,

400f/480ps recording, H.264, Recording @704x480 (100/120ips)/ 704x240

(200/240ips)/ 352x240 (400/480ips), 8Audio In/ 1 Out, 16 Alarm In, 4 Relay Out,

Network Port available for Remote View S/W with transmission up to 120 IPS @

352x288 PAL, along with 3 TB HDD, complete all as specified with 230VAC power

supply complete in all respects as per specifications as per engineer in charge.

Supply, installation, testing and commissioning of High Resolution 32 inch LCD

7.3 colour TV monitor with on screen adjustment menu, durable metal cabinet etc. Nos. 1 Rs. 42,500 Rs. 42,500

complete in all respects as per specifications as per engineer in charge.

Supply and fixing of following sizes of MS conduit along with accessories in surface

7.4 1.20 /recess including painting in case of surface conduit,or cutting the wall and

making good the same in case of recessed conduit as required

7.5 MR Supply and fixing of RJ45 Connector Nos. 10 Rs. 373 Rs. 3,730

Supplying and fixing in position GI box for data outlet suitable for fixing of RJ 45

face plate complete as required.

Supply & fixing of Plug in type RJ45 computer data outlet in existing faceplate/ GI

Box in wall/furniture/floor complete as required.

Supply & Fixing of Single Faceplate, Single Port square plate having spring

7.8 MR shuttered front access for preventing ingress of dust, dimension as per commercially Nos. 10 Rs. 101 Rs. 1,010

available modular office furniture.

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair LAN Cable in

the existing surface/ recessed Steel/ PVC conduit as required.

TOTAL OF IP BASED CCTV SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 307,948 Rs. 81,920

Amount after GST Multiplication factor on DSR Items @1.0633 Rs. 307,948 87,105.54

Digitally signed by RAJ PAL

Sr. NDSR Total

2022. Description Unit Qty Unit Rate DSR Total amount

2022. Description Unit Qty Unit Rate DSR Total amount

8 ESTIMATED COST FOR ACCESS CONTROL SYSTEM

Supply, Installation, Testing & Commissioning of SCOSTA Based with 1 SAM Slot 4

Door Intelligent Access Control Controller vthrough Master/Slave

Architecture(optional), TCP/IP, IPV6, SNMP V3 ,200,000 card holder capacity,

200,000 transactions buffer, 32 acess levels per card holder, OSDP Secure Channel,

Supports 2 Doors, 4 Readers (OSDP) per controller (IN/OUT Reader Combination),

Integration with Fire Alarm System, Integration with Fire Alarm System, Open

Architecture - supports Multiple OEM Software, Supports downstream readers via

cable, UL Listed. as per specifications of this tender etc complete as required and

directions of Engineer-in-Charge.

Controller shall be installed inside ELV rooms & Utility Buildings including all

accessories complete as per specification/drawings and as directed by Engineer

Access Control System Software :-

Enterprise version Server software with Time attendance management system

as per specification with client version. Supply, installation, testing and

commissioning of Access Control System Server Software consisting of Access

Control system, Visitor management with all employee visitor license, Elevator

Control, Guard Tour Management , Mantrap, Alarm Document, Alarm Each 1.00 1,042,210.62 Rs. 1,042,211

management, 3 client License, Graphical layout, Card Enrolment, Badge

designing..All these along with high end security features consist in single package

with an option to integrate with CCTV sub system (License based ), VAPT and ISO

Certified as per specifications of this tender etc complete as required and

directions of Engineer-in-Charge.

Supply, Installation,Testing & Commissioning of Smart Card Reader 13.56 MHz

Credential as per specification Card Range:7 to10cm suitable for mounting on

metal surface/metal frames/ wooden frames / wall or as required based on site

conditions including all accessories complete as per specification/drawings Each 2.00 17,680.00 Rs. 35,360

and as directed by Engineer In Charge.

In case of SAM based SCOSTA Smart Card Reader - Minimum 1 SAM slot shall be

Digitally signed by RAJ PAL

Supply, Installation,Testing & Commissioning of Biometric - cum- Smart card

Reader supporting up to three-factor authentication. Support card/biometric

fingerprint, card/PIN or card/fingerprint/PIN. 13.56 MHz Credential

Compatibility. Operating Temperature -10° to 50° C; Operating Humidity : 5%

to 95% relative humidity non- condensing. ANSI-378 template stored on smart

card credential and verified on reader. Suitable for mounting on metal

surface/metal frames/ wooden frames / wall or as required based on site

conditions including all accessories complete as per specification/drawings and

as directed by Engineer In Charge.

Certification : BIS, CE, FCC

In case of SAM based SCOSTA Smart Card Reader - Minimum 1 SAM slot shall be

OEM Programmed Unprinted 37 bit Smart Cards.AES-128 bits cryptographic

algorithms for data protection. Supports ISO/IEC standards: 7810, 7816 and

contactless cards (14443 A) complete as per specification and as directed by

Engineer In Charge.:-

In case of SAM based SCOSTA Smart Card Reader - Smart card must have

SCOSTA CL OS and 64KB of memory"

Supply, Installation, Testing and Commissioning of Access Control Server with

Windows 10 Pro OS, SQL Database along with MS.Office Intel® Core™ i7- 10700

(16 MB cache, 8 cores, 16 threads, 2.90 to

4.80 GHz Turbo, 65W), 8 GB, 1 x 8 GB, DDR4, 3200 MHz, Intel® Integrated Graphics, Each 1.00 486,952.00 Rs. 486,952

3.5 inch 1TB 7200 RPM Hard Disk Drive, 64 MB cache, 4 GB AGP Graphics

Card, Windows 10 OS Professional 64bit or above etc, Keyboard and

Mouse as per the requirement of the surveillance system complete

Supply, Installation, Testing and Commissioning of Electro Magnetic Lock,

Lock Status Monitoring through LED,Low Energy Consumption, Electroless Nickel

(EN) Plated Armature Plate, 12/24V Selectable, Anodized Aluminium Housing, CE

Compliance, Ideal for all door type.

Single leaf Door Each 1.00 10,691.00 Rs. 10,691

Double leaf Door Each 1.00 18,540.00 Rs. 18,540

Providing & Laying of Armored, PVC insulated and PVC shiethed AB Copper

Shielded Flexible Cable on existing wall surface etc. complete as reqd.

Supply, Installation, Testing and Commissioning of Green ABS plastic Emergency

glass break Units etc. complete as reqd.

Supply, Installation, Testing and Commissioning of Magnetic contacts for all

access doors (one for each single leaf door and two for each double leaf doors) Each 3.00 2,325.00 Rs. 6,975

etc. complete as reqd.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

Digitally signed by RAJ PAL

Supplying and fixing of following sizes of medium class PVC conduit

1.21 along with accessories in surface/recess including cutting the wall

and making good the same in case of recessed conduit as required.

TOTAL OF ACCESS CONTROL SYSTEM CARRIED OVER TO SUMMARY Rs. Rs. 1,941,461 Rs. 15,370

Amount after GST Multiplication factor on DSR Items @1.0633 Rs. 1,941,461 16,342.92

Digitally signed by RAJ PAL

ESTIMATED COST FOR FA & PA SYSTEM

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : MR. DSR.

Sr. No Description Unit Qty Unit Rate Total amount Total amount

Sr. No Description Unit Qty Unit Rate Total amount Total amount

Supplying, installation, testing and commissioning of micro processor

based intelligent addressable main fire alarm panel, central processing

unit with the following loop modules and capable of supporting not less

than 240 devices (including detectors) and minimum 120 detectors per

loop and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile memory

1 17.2.1 (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt

sealed maintenance free batteries with automatic charger. The panel

shall have facility to connect printer to printout log and facility to have

seamless integration with analog/digital voice evacuation system (which

is part of the schedule of work under SH: PA System) and shall be

complete with all accessories . The panel shall be compatible for IBMS

system with open protocol BACnet/ Modbus over IP complete as per

specifications.

Supplying, installation, testing & commissioning of intelligent analog

2 17.2.4 addressable photothermal detector complete with mounting base Pcs 23.00 2,858.00 65,734.00

complete as required.

Supplying, installation, testing & commissioning of intelligent addressable

3 17.2.9 thermal detector with rate of rise cum fixed tempreature thermistor Pcs 1.00 2,726.00 2,726.00

complete with base as required.

Supplying, installation, testing & commissioning of addressable manual

call point complete as required.

Supplying, installation, testing & commissioning of addressable strobe

complete as required.

Supplying, installation, testing & commissioning of fault isolator complete

with base as required.

Supplying, installation, testing & commissioning of response indicator on

7 17.2.5 surface/recessed MS Box having two LED, metallic cover complete with Pcs 10.00 276.00 2,760.00

all connections etc as required.

B CABLES & ACCESSORIES FOR FAS :

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V

1 17.5.2 rated with annealed copper conductor having XLPE insulation, steel wire RM 150.00 173.00 25,950.00

armouring & FRLS outer sheath complete as required.

C SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES :

Supplying, installation, testing & commissioning of 6 zone, voice alarm

controller with USB, MP3 player (including 6 zone button paging station)

with seamless integration facility with main fire alarm panel for voice

evacuation complete as required.

Digitally signed by RAJ PAL

ESTIMATED COST FOR FA & PA SYSTEM

A. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : MR. DSR.

Sr. No Description Unit Qty Unit Rate Total amount Total amount

Sr. No Description Unit Qty Unit Rate Total amount Total amount

Supplying, installation, testing & commissioning of digital audio amplifier

50 Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted

loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

D CABLE & ACCESSORIES FOR PA SYSTEM

Supplying and drawing of cable Fire Retardant PVC insulated copper

conductor cable in the existing surface / recessed steel conduit of

following pairs, cores and size including connections and

interconnections etc. as required.

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm RM 100.00 54.00 5,400.00

Supply and fixing of following sizes of MS conduit along with accessories

in surface /recess including painting in case of surface conduit,or cutting

the wall and making good the same in case of recessed conduit as

Amount after GST Multiplication factor on DSR Items @1.0633 729,793.83

Digitally signed by RAJ PAL