Provn of Certain Special repair, LBW, Revenue and Minor works of AGE B/R I under GE (N) Bikaner at Mil Stn Bikaner

Amount

Surface dressing not exc 15 cm deep in soft/loose soil.

Excavation in trenches for foundation etc not exc 1.5m wide and not exc 1.5 m in depth in any type of soil all as specified.

Removal of excavated material to a distance nexc 50 m and depositing at a level nexc 1.5 m above the starting point

Removing excavated material exc. 500m and nexc 1.50 Km , depositing where directed at a level not exc. 1.50m above the starting point in soils

Returning filling in including spreading levlling, catering and well ramming in layers nexc 25cm thick complete all as specified.

Excavation in post holes or similar holes each nexc 0.5 cum getting out in any type of soil

Dismantling of Asbetose cement (corrugated, semi-corrugated, etc.) sheets in roofing complete .

Demolition of brick work built in cement mortar including all quions.

Demolition floor, hearth or wall tiling including cement mortar bedding but not backing layer and removal of rubbish complete all as specified and as directed by Engineer-in-charge.

Dismantling structural steel framed trusses n exc 10 m span complete directed by Engineer-in-Charge.

Demolition of un reinforced cement concrete in ground floors and paving not exc 15cm thick (below and above GL).

Dismantling of water tanks cap exc 250 & n exc 500 ltrs.

Demolition of reinforced concrete of any description and in any position ( reinforcement cut as required to facilitate demolition) complete all as specified and as directed by Engineer-In-Charge.

Dismantling old Textile (Hassion cloth) covering including frame and cover fillets as in false ceiling complete

Taking up or down steel water tubing 15mm dia and connection , including cleaning for refixing.

Taking up or down steel water tubing 20mm dia and connection , including cleaning for refixing.

Taking down cement plaster on brick stone or concrete surfaces including raking out joints hacking for keys and scrubbing down with water.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frame) and removal from site

Taking down chowkats or frames exc 1.5 sqm and not exc 4 sqm each with shutters (without taking off shutters from the frame) and removal from site

Rolling and consolidation formation to surfaces in cutting and filling with 8 to 12 tonnes roller.

Hardcore of gauge nexc 63mm , deposited , spread and levelled in layers nex 15cm thick watered and rammed to a true surface

PCC 1:4:8,type D-2 using 40mm graded crushed stone aggregate as in sub base and mass conc.

Cement concrete (1:5:10) type E2 using 40mm graded stone aggregate as in foundation, filling, sub base and mass concrete all as specified.

Cement concrete 1:3:6 type C-2 using (40mm graded aggregate) in foundations , filling and mass concrete in sub floors, even and rough complete all as specified and as directed by Engineer-In-Charge.

Brick work with fly ash bricks straight or curved on plan exc 6m mean radius , built in cement mortor 1: 6 complete all as specified and as directed by Engineer-In-Charge.

Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:4 comp all as specifeid.

Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 comp all as specifeid.

Brick work in cement mortar (1:4) in modular size bricks using sub class B bricks in walling ,straight or curved on plan to any radius to half brick thick .

40 mm thick for damp proof course to horizontal surfaces in cement concrete 1:2:4 type B0 using 12.50 mm graded aggregate incl all necessary form work

Form work to soffits of suspended slab floor slab and similar works n exc 200 mm thick wide finished rough.

Formwork to sides and soffits of floors or roof beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. finished to rough surface. Complete alll as specified and as directed by Engineer-in-charge.

Mild steel TMT bars 10mm dia and over dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia confirming to complete all as specified and directed by Engineer-in-charge.

Ditto as per item no 32 but 6mm to 8mm dia

Mild steel TMT bars 5mm dia and over upto incl 10mm cut to length bent to shape as reqd ,as in stirrups and spacers.

Reinforced cement concrete type B-1 1:2:4 ( 20mm graded aggregate) as in slabs/shelves complete all as specified and as directed by Engineer-in-Charge.

Form work to edges of concrete flats nexc 20 cm wide

PCC 1:3:6 type B-0 using 12.50 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; sesmic and other similar bands, plinth courses, string courses, lacing courses, parapet and railings upto 60 cm in height, copings, kneers, apex stones, bed plates, in pressed steel frames complete all as specified and as directed by Engineer-In-Charge.

PCC 1:2:4 type B1, using 20mm graded stone aggregated as in coping ,plinth band, lintel band, roof band and other similar bands etc all as directed by Engr-in-Charge at site.

Rendering 15mm thick on fair faces of brick or conc. Surfaces in cement mortar 1:4 finishing he surface even and fair.

Rendering 15mm thick on fair faces of brick or conc. Surfaces in cement mortar 1:4 finishing he surface even and smooth without using extra cement incl mixing of WPC if required . (Note WPC shall be measured and paid for separately)

Rendering 15mm thick on fair faces of brick or concrete surfaces as in walls, chajjas, parapets etc in CM 1:6 finished even and smooth without using extra cement.

Rendering 10mm thick on fair faces of brick or concrete surfaces as in walls, chajjas, parapets etc in CM 1:4 finished even and smooth without using extra cement.

Supply only integral water proofing compound .

Supply only liquid water proofing compound .

Supply only chain link MS galvinised fencing any size and type ( Wt 2 Kg/ sqm approx) as specified and directed

MS flat iron 40x6 to secure chain link fencing all as specified and directed.

Mild steel round bars 10 mm dia or over, cut to length, bend to shape required, fixed independently to support chain link fencing complete all as specified. Fe 410-0 or Fe 310-0

Fixing only chain link fencing incl line wire any mesh size

Mild steel bolts purpose made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut. Dia exc 5 to 10 mm dia and nexc 5 cm long.

Framed work as in doors and gates of angle or other section including stringers,ms plates, braces etc complete drilled for fixing of steel sheeting or other coverings to doors etc conforming FE-410-W grade E-250 quality ‘A’.

Mild steel bolts , purpose made with hexagonal or square head one end and screwed the other end or screwed both ends ; each screwed end to be fitted with washers and one hexagonal or square nut , exceeding 30 cms, dia metre of neck n.exc 12 mm complete all as specified.

Tie bars with screwed ends, nuts washers and mild steel plates for walls, chimneys, roofs, arches, etc. King rods and straining bolts conforming to fe.290. Gde-E-165 complete all as specified and as directed by Engineer-In-charge.

Angle iron section as in horns posts struts including notching drilling holes for wire mesh etc; conforming to Fe-290

MS plates/flates angle etc as in cleat gusset incl drilling welding etc Fe FE-410-W grade E-250 quality ‘A’.

Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. FE-410-W grade E-250 quality ‘A’.

Steel work in tubular trusses including special shaped washer etc using ERW or induction butt welded confirming to IS 1161-1971 grade ST 240.

As per item no. 56 but in refixing ( including erection and fixing only )

M&L for rolled section as in framing cladding, glazing and the like fixed with angle cleats and connecting plates conforming to Fe- 410-w (gde-250) quality-B.

Pre painted galvatume aluminium zinc coating based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed by Engineer-in-Charge.

Pre painted galvatume aluminium zinc coating based plain steel sheet 0.50mm thck of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed by Engineer-in-Charge.

S&F Anodized aluminium snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 35 x 25 x 1.4 mm weighing 0.24 Kg/RM and 25 x 25 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size 35 x 25 x 1.6 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre boards in grid fixed as false ceiling grid made of aluminium as per specification all as specified and directed by Engineer-in-Charge.

Providing false ceiling GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 to 30mm and web of 27 mm fixed to surrounding wall using screws at 450mm C/C channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm C/C with GI cleat and steel expansion of suitable hanging from soffits/trusses/bracking supporting hanger compressing of GI wire with 4mm thick 600 x 600 mm size asbestos cement plain building boards designer ceiling fixed to GI grid work with screws and applying new surfaces two coat of distemper over one coat of primer complete all as specified and directed Make- Everest/ BISON/RAMCO or equivalent approved make.

Plain mild steel wire of dia 3.15mm , galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staplles or steel pin including suspenders and adjusters etc. as directed (each line of wire to be measured )

25 mm thick PCC type B-1 , (1:2:4) using 20mm graded crushed stone aggregate as in sub base for laying floor finishes.

Screed bed or bedding Layer of mortar 15mm thick for laying of floor finishes in CM 1:4. complete all as specified and as directed by Engineer-in-Charge.

75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate)

150mm PCC 1:4:8 in sub floors, sub bases, (Levelling course to raise floor etc) even and rough to receive the topping layer complete all as specified and as directed by Engineer-In-Charge.

20mm thick Black granite machine cut slab table rubbed and polished granite as on cooking platforms incl. pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade laid over 20mm thick cement screed in cement mortar 1:6.

Machine cut kota stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match ;the shade of slab incl. rubbing and polishing laid over 20 mm thick cement screed base in CM 1:6

All as per item No 69 above but as in skirtings and dados etc over 10mm rendering in CM 1:4

Non skid tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sq, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured over 15mm screed bed in CM 1:6 complete all as specified and as directed by Engineer-In-Charge.

Non skid tiles 7 to 10 mm thick on verticle surface (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sq, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured over 10 mm screed bed in CM 1:4 complete all as specified and as directed by Engineer-In-Charge.

All as per item No 72 above but on vertical surface over 10 mm thick rendering in CM (1:4).

Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement over 15mm screed bed in CM 1:6

Non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement over 15mm screed bed in CM 1:6

Glazed ceramic tiles on verticle surface with glazed ceramic tiles of any colour of size 350x250 x 7mm /450x350x7 thick over 10 mm rendering in CM 1:4 including removing of existing skirting

40mm thick PCC type B-1 1:2:4 , using 20mm graded crushed stone aggregate as in flooring finished even and smooth without using extra cement.

Supply only 3mm thick 38mm wide glass dividing strips laid in design as directed by Engr-in-charge

Sand filling under floors, cushioning under interlocking tiles or in foundations incl watering and consolidations complete all as specified and directed.

Cement concrete with grey cement and no pigment machine pressed precast concrete interlocking paver block any shape and size conforming to IS15658-2006 of 60mm thickness, M-35 Grade complete all as specified and as directed by Engineer-In-charge.

80mm thick machine pressed pre-casted concrete interlocking tiles/paver blocks any shape size conforming to IS 15658-2006 of M-35 grade laid over 50m thick sand cushioning with grey cement or mixed with pigment as directed by Engr-in-charge.

Cement concrete tiles 20cmx20cmx20mm thick machine pressed; with grey cement and pigments set jointed and pointed in neat cement slurry in floors, and cut and polished. Complete all as specified and as directed by Engineer-In-Charge.

PCC 75 mm thick 1:3:6 type C-2 using 40mm graded agg as in plinth protection finished surfaces even and smooth laid in alternate pannels.

40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in plinth protection and in chajjas complete ass as directed

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889/2018 and Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer complete all specified. Note : (i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Box type steel ventilators top hung/Partly fixed shutters including hinges, steel peg stays and one coat of zinc chromate primer all as specified

Framed work such as grills, gratings etc. with end of bars shouldered and or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde E-165 complete all as specified and as directed by Engineer-In-Charge

Galvanised wire cloth 0.56mm nominal dia of wire and avg.width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples.

Sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane.

All as per Item No 89 above but 0.63 mm nominal dia of wire and average width of aperture 1.18mm

1.25 mm thick Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

1.25 mm thick Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provisions.

Cement concrete 1:3:6 type Co using 12.5 mm graded stone aggregate as in Filling in pressed steel frame chowkhats etc complete

Butt hinges extruded aluminium alloy with galvanised mild steel hinges pin anodised and fixed ,type B-21 of 100mm.

Aluminium anodised barrel tower bolt of extruded section of 2000mm

Aluminium anodised barrel tower bolt of extruded section of 150mm

Aluminium handles cast type anodised of 150mm

Aluminium Locking Bolt 250mm size

Anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified and as directed by Engineer-In-Charge.

Sheet glass 5.5mm thick , ordinary quality, in squares exc. 0.5 Sqm each Pane complete all as specified and as directed by Engineer-in-charge.

Aluminium extruded section Door closer hydraulically regulated designated No.3 universal type, suitable for doors shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed by Engineer-In-Charge.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

Factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification.

IInd class hardwood in plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamffered put together with glue pinned at joints complete all as spfd and directed

Plain framed, (factory made 35mm thick of IInd class hard wood panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.

35mm thick glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc II nd class hard wood edges of framing plain, chamfered, rounded or mitred fitted with cut and mitred beads size of members of shutters as specified in SSR-I Section 8 clause 8.20(a)

Mild steel but hinges medium weight cold rolled 100mm size

As per item No 108 but 75 mm size

Mild steel barrel tower bolts stove enamelled black with gright bolt 200mm size

Mild steel pressed handles oval type stove enamelled black 150mm size

Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate

MS sliding door bolts 300mm size, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum 6 bolts and nuts four on bolt plate and two on staple plate and fixed.

Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints fixed to walls, 50mm dia.

Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints 100mm dia laid in trenches.

Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints 75 mm dia laid in trenches.

CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4, 75mm dia.

CI Bends (any radius), diminishing pieces or tappers(larger bore measures), 100mm dia with access door.

CI Bends (any radius), diminishing pieces or tappers(larger bore measures), 75mm dia with access door.

CI Branch pieces ,Double (equal or unequal ) ordinary or inverted (spigot or socket type) or with parallel branches 100 mm dia.

CI vent cowls , 50mm dia

PVC (SWR ) pipe single socketed in any length with rubber ring joints fixed to walls for 75 mm bore pipe.

As per item No 122 but 110 mm bore pipe

PVC (SWR) branch piece equal or unequal plain including jointing with solvent cement 75 mm bore complete all as specified

PVC (SWR) vent cowl plain including jointing with solvent cement 75 mm bore complete all as specified

PVC (SWR) floor bend plain incl jointing with solvent cement 75 mm bore complete all as specified

As per item No 126 but 110 mm bore .

PVC (SWR) reducer pipe piece plian plain incl jointing with solvent cement 110 mm bore complete all as spfd.

PVC (SWR) floor trap plain with grating including jointing with solvent cement 75 mm bore complete all as spfd.

PVC (SWR) gully trap plain with grating jointing with solvent cement 110 mm bore.

Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 50mm bore piece.

Viterous china squatting pan Orissa pattern size 580x440mm white with integral footrest incl trap

Vitreous china wash hand basin white flat back, size 550x400 including 32mm CP waste coupling, PTMT PVC connections 15mmX450mm, 15mm dia fancy type CP Pillars Taps , 15mm dia stop valve, CP fancy type, Shelf of PTMT fixed with CP Brass screw and wood etc complete all as specified.

PVC flushing cistern, low level, white with inlet, ball valve, complete including connection to pipe all as specified.

Looking mirror of size 600mm x 450mm with PVC beading fitted over 6mm thick commercial ply complete all as specified.

32mm bore waste fittings ,brass chromium plated for wash hand basin etc with long screwed shank and fly nuts etc.

Pillar tap , fancy type with capstan head , chromium plated , screwed down under high pressure with or w/o lettered hot or cold with long screwed shanks for iron pipe of bore 15mm complete all as specified.

Chromium plated Bib Tap, with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia

Towel ring of PTMT with and incl chromium plated brass screws and wooden /plastic cleats

PTMT glass shelf with and including chromium plated brass screws and wooden cleats

Chromium plated stop cock/angular stop cock , with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia

15mm bore PVC connection with PTMT nuts.

Rotational moulded polyethylene water storage tanks of capacity 1000 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall be white coloured with three layered wall and shall be ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

Rotational moulded polyethylene water storage tanks of capacity 500 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall be white coloured with three layered wall and shall be ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

20 mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe

15 mm bore chromium plated Bib taps, cast copper alloy with alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engineer-In-Charge. (Make: Parko,Gem,Essco

15 mm bore brass chromium plated stop cock with crutch or butter fly handle screwed down , screwed for iron pipe or brass ferrule.(Make: Parko,Gem,Essco

Tubing galvanised medium grade with all fittings fixed to walls or laid in floors 15mm dia.

Tubing galvanised medium grade with all fittings fixed to walls or laid in floors 20mm dia.

Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair.

Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia fixed in repair.

Preparing newly plastered surfaces of walls and applying three coats of White wash all as specified

As per item No 152 but two coats of white wash on ceiling

Complete removal of existing treatment of walls and applying two coats of distemper oil emulsion, over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing treatment of walls and applying two coat of cement base paint (Ist quality) in plain pattern on walls and over a coat of alkali resistant priming paint complete all as specified.

Preparation of new or old untreted surfaces of plastered/unplastered by brooming down etc and applying two coats of distemper oil emulsion, white or tinted over a coat of chalk whiting on wall complete all as specified and as directed by Engineer-in-Charge.

Preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a priming of alkaili resistant priming paint complete all as specified and as directed by Engineer-In-Charge.

Preparing new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer

Preparing new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer

Preparing pre prime steel surface and applying two coats of synthetic enamel paint.

Soakage wells with excavation, in ordinary soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-25 concrete, including intercepting chamber, screen chamber, brick work in CM, RCC cover slab in M-25/RR masonary/filling with brick bats, complete of size 3.0 m dia x 3.00 m deep complete all as shown and specified on TD drg

Concrete bed to drain pipes(New pipe) including packing under and completely surrounding pipes with concrete after they are laid in cement conc. 1:4:8 type D-2 using 40mm graded stone aggregate For 150mm pipe.

Salt glazed stone ware drain pipes laid in trenches for grade A.150mm bore internal dia over existing concrete bedding and jointed as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and refofming benching as required.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds , mitered/ stopped ends etc

Septic Tanks, with excavation, in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole covers having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chamber etc. complete for 10 users all as specified and shown in TD drgs.

Soakage pit with excavation in ordinary soil , filled with bats and PCC plaster on top for 1.50 mtr dia and 1.50 mtr deep for soakage pit with and including brick tile layer on top and CI pipe 100 mm bore up to centre of pit complete all as specified and directed by Engr-in-Charge.

M & L for RCC (1:2:4) type B-I 20 mm graded aggregate for precast cement concrete in landings cover slabs (for man holes etc.) chullab hoods, chajjas, water troughs, mangers, shelves and similar articles with

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid surface PVC conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 171 here-in-before but socket point on the same board with other switches complete as specified as directed by Engineer - In - Charge

All as per item No 171 here-in-before but socket point on the independent board with other switches complete as specified as directed by Engineer - In - Charge

All as per item No 171 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/Cona/Havells

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Make : Anchor/Cona/Havells

S&F Socket outlet flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : - Anchor/Cona/Havells

S&F Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/Cona/Havells

S&F Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Anchor/Cona/Havells

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings with LED Bulb 9W complete all as specified and as directed by Engineer-in-Charge. Make :- Anchor/Cona/Havells

S&F Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge. Make Anchor/Cona/Havells

S&F Decorative ultra slim linear LED lightening fixture, energy efficient 18/20 Watt complete all as specified and directed by engineer-in-charge. Make Surya /Phillips/wipro/CG /Bajaj

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard/BCH/HPL

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Schneider/ HPL/Legrand/ GE/ Seimens/L&T/Indo sian/C&S/Havells/BCH/ABB

S&F MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ GE/ Seimens/L&T/Indo Asian/C&S/ABB/BCH /Havells

Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 4 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 4 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

Suppy and Fixing LED based security light, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 7200 lumens and maximum system wattage 25 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be withstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG/C&S/Bajaj/Havells

Supply and fixing Street light bracket , made of GI pipe 40mm bore, light grade not less than 1.2 m long bent to shape including fixing with 2 nos suitable size of MS flat iron clamps, nuts, bolts and washers and making connections all as directed by the Engineer-in-Charge. Make of GI pipe : Jindal/Surya/Prakash

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I.

S&F in replacement Plug and socket in sheet metal inclosure with 2 pin and earth plug and socket complete with and including MCB, SP, 20 Amps, 240 Volts heavy duty all as specified and as directed by Engineer-in -Charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and

Hanging only ceiling fan as taking down vide item si no. 23 and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.00 sq mm 3 core

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 mtr in depth for route of cable and getting out complete all as specified and as directed by the Engr-in-charge.

Returning, filling in soft/loose soil including spreading, leveling watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engr-in-charge.

Removing of surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.

Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.

M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 200 here-in-before but socket point on the same board with other switches complete as specified as directed by Engineer - In - Charge

Supply & fixing exhaust fans copper winding AC single phase 230/ 240 V of size 225 mm sweep heavy duty with louvers, frame, supporting legs and grouting with anchor fastener complete all as specified and directed by Engr-in-charge. Make : CG/ Havells/Orient /Khaitan.

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 2 ways , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard/BCH/HPL

S&F New sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 6sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 6 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

JAMUNA CONSTRUCTION AND GENERAL ORDER SUPPLIER

N.K. CONSTRUCTION COMPANY

SHREE GURU NANAK CONSTRUCTION COMPANY

MAHAVIR CONSTRUCTION CO

ALPHA ENGINEERING COMPANY

durga construction company

M/S ASHRAFI CONSTRUCTION CO

Beenu Co. Company